UT54ACTS157E Quadruple 2 to 1 Multiplexers July 2013 www.aeroflex.com/Logic PINOUTS 16-Lead Flatpack Top View FEATURES * m CRH CMOS process - Latchup immune * High speed * Low power consumption * Wide power supply operating range of 3.0V to 5.5V * Available QML Q or V processes * 16-lead flatpack * UT54ACTS157E-SMD-5962-96553 DESCRIPTION The UT54ACTS157E is a monolithic data selector/multiplexer. A 4-bit word is selected from one of two sources and is routed to the four outputs. A separate strobe input, G, is provided. A/B 1 16 1A 2 15 G 1B 3 14 4A 1Y 4 13 4B 2A 5 12 4Y 2B 6 11 3A 2Y VSS 7 8 10 9 3B (15) G (1) A/B 1A FUNCTION TABLE SELECT A/B DATA A B Y H X X X L L L L X L L L H X H L H X L L L H X H H EN G1 (2) (3) 1B (5) 2A (6) 2B (11) 3A (10) 3B (14) 4A (13) 4B OUTPUT STROBE G 3Y LOGIC SYMBOL The device is characterized over full HiRel temperature range of -55C to +125C. INPUTS VDD 1 1 MUX (4) (7) (9) (12) 1Y 2Y 3Y 4Y Note: 1. Logic symbol in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 1 LOGIC DIAGRAM 1A (2) (4) 1B 2A (3) (5) (7) 2B (6) 3A (11) (9) 3B 4A (10) STROBE G SELECT A/B 2Y 3Y (14) (12) 4B 1Y (13) (15) (1) 2 4Y OPERATIONAL ENVIRONMENT1 PARAMETER LIMIT UNITS Total Dose 1.0E6 rads(Si) SEU Threshold 2 108 MeV-cm2/mg SEL Threshold 120 MeV-cm2/mg Neutron Fluence 1.0E14 n/cm2 Notes: 1. Logic will not latchup during radiation exposure within the limits defined in the table. 2. Device storage elements are immune to SEU affects. ABSOLUTE MAXIMUM RATINGS1 SYMBOL PARAMETER LIMIT UNITS VDD Supply voltage -0.3 to 7.0 V VI/O Voltage any pin -0.3 to VDD +0.3 V TSTG Storage Temperature range -65 to +150 C TJ Maximum junction temperature +175 C TLS Lead temperature (soldering 5 seconds) +300 C JC Thermal resistance junction to case 15 C/W II DC input current 10 mA PD2 Maximum package power dissipation 3.3 W o permitted @ Tc = +125 C Note: 1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. Per MIL-STD-883, method 1012.1, Section 3.4.1, PD = (Tj(max) - Tc(max) ) / jc RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMIT UNITS VDD Supply voltage 3.0 to 5.5 V VIN Input voltage any pin 0 to VDD V TC Temperature range -55 to + 125 C 3 DC ELECTRICAL CHARACTERISTICS FOR THE UT54ACTS157E7 ( VDD = 3.0V to 5.5V; VSS = 0V6; -55C < TC < +125C) SYMBOL DESCRIPTION CONDITION MIN MAX UNIT VIL1 Low-level input voltage 1 VDD from 4.5V to 5.5V 0.8 V VIL2 Low-level input voltage 1 VDD from 3.0V to 3.6V 0.8 V VIH1 High-level input voltage 1 VDD from 4.5V to 5.5V 0.5 VDD V VIH2 High-level input voltage 1 VDD from 3.0V to 3.6V 2.0 V Input leakage current VIN = VDD or VSS -1 Low-level output voltage 3 IOL = 8mA IIN VOL1 1 A 0.4 V 0.4 V VDD = 4.5V to 5.5V VOL2 Low-level output voltage 3 IOL = 6mA VDD = 3.0V to 3.6V VOH1 High-level output voltage 3 IOH = -8mA 0.7 VDD V 2.4 V VDD from 4.5V to 5.5V VOH2 High-level output voltage 3 IOH = -6mA VDD from 3.0V to 3.6V IOS1 Short-circuit output current 2 ,4 VO = VDD and VSS -200 200 mA -100 100 mA VDD from 3.0V to 3.6V IOS2 Short-circuit output current 2 ,4 VO = VDD and VSS VDD from 3.0V to 3.6V IOL1 Low level output current 9 VIN = VDD or VSS 8 mA 6 mA -8 mA VOL = 0.4V VDD from 4.5V to 5.5V IOL2 Low level output curren 9 VIN = VDD or VSS VOL = 0.4V VDD from 3.0V to 3.6V IOH1 High level output current 9 VIN = VDD or VSS VOH = VDD-0.4V VDD from 4.5V to 5.5V 4 IOH29 High level output current VIN = VDD or VSS -6 mA VOH = VDD-0.4V VDD from 3.0V to 3.6V Ptotal1 Power dissipation 2, 8 CL = 50pF 1.3 mW/ MHZ 0.75 mW/ MHZ 10 A 1.6 mA VDD = 4.5V to 5.5V Ptotal2 Power dissipation 2, 8 CL = 50pF VDD = 3.0V to 3.6V IDDQ Quiescent Supply Current VIN = VDD or VSS VDD from 3.0V to 5.5V IDDQ Quiescent Supply Current For input under test Delta VIN = VDD -2.1V For all other inputs VIN = VDD or VSS VDD = 5.5V CIN COUT Input capacitance 5 = 1MHz, VDD = 0V 15 pF Output capacitance 5 = 1MHz, VDD = 0V 15 pF Notes: 1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: VIH = VIH(min) + 20%, - 0%; VIL = VIL(max) + 0%, - 50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are guaranteed to VIH(min) and VIL(max). 2. Supplied as a design limit but not guaranteed or tested. 3. Per MIL-PRF-38535, for current density 5.0E5 amps/cm2, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765 pF/MHz. 4. Not more than one output may be shorted at a time for maximum duration of one second. 5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and VSS at a frequency of 1MHz and a signal amplitude of 50mV rms maximum. 6. Maximum allowable relative shift equals 50mV. 7. All specifications valid for the maximum radiation dose available for the respective device types. 8. Power dissipation specified per switching output. 9. Guaranteed by characterization, but not tested. 5 AC ELECTRICAL CHARACTERISTICS FOR UT54ACTS157E2 (VDD = 5.0V 10%; VSS = 0V 1, -55C < TC < +125C) SYMBOL tPHL1 tPLH1 tPHL2 tPLH2 tPHL3 tPLH3 PARAMETER mA or mB to mY mA or mB to mY G to mY G to mY A/B to mY A/B to mY CONDITION VDD CL=50pF 3.0V to 3.6V CL=50pF CL=50pF CL=50pF CL=50pF CL=50pF MAXIMUM UNIT 3 20 ns 4.5V to 5.5V 2 11 3.0V to 3.6V 3 18 4.5V to 5.5V 2 10 3.0V to 3.6V 3 18 4.5V to 5.5V 2 10 3.0V to 3.6V 3 18 4.5V to 5.5V 2 10 3.0V to 3.6V 3 19 4.5V to 5.5V 2 11 3.0V to 3.6V 3 17 4.5V to 5.5V 2 10 Notes: 1. Maximum allowable relative shift equals 50mV. 2. All specifications valid for the maximum radiation dose available for the respective device types. 6 MINIMUM ns ns ns ns ns Packaging 7 Ordering Information: UT54ACTS157E: SMD 5962 * ***** ** * * * Lead Finish: (Notes 1 & 2) A = Solder C = Gold X = Optional Package Type: X = 16-lead ceramic bottom-brazed dual-in-line Flatpack Class Designator: Q = QML Class Q V = QML Class V Device Type: 02 = 1 rad(Si)/sec 03 = 50 to 300 rads(Si)/sec Drawing Number: 96553 = UT54ACTS157E Total Dose: (Note 3 and 4) R = 1E5 rads(Si) F = 3E5 rads(Si) G = 5E5 rads(Si) H = 1E6 rads(Si) Notes: 1. Lead finish (A,C, or X) must be specified. 2. If an "X" is specified when ordering, part marking will match the lead finish and will be either "A" (solder) or "C" (gold). 3. Total dose radiation must be specified when ordering. QML Q and QML V not available without radiation hardening. For prototype inquiries, contact factory. 4. Device type 02 is only offered with a TID tolerance guarantee of 3E5 rads(Si) or 1E6 rads(Si) and is tested in accordance with MIL-STD-883 Test Method 1019 Condition A and section 3.11.2. Device type 03 is only offered with a TID tolerance guarantee of 1E5 rads(Si), 3E5 rads(Si), and 5E5 rads(Si), and is tested in accordance with MIL-STD-883 Test Method 1019 Condition A. 8 Aeroflex Colorado Springs - Datasheet Definition Advanced Datasheet - Product In Development Preliminary Datasheet - Shipping Prototype Datasheet - Shipping QML & Reduced HiRel COLORADO Toll Free: 800-645-8862 Fax: 719-594-8468 INTERNATIONAL Tel: 805-778-9229 Fax: 805-778-1980 NORTHEAST Tel: 603-888-3975 Fax: 603-888-4585 SE AND MID-ATLANTIC Tel: 321-951-4164 Fax: 321-951-4254 WEST COAST Tel: 949-362-2260 Fax: 949-362-2266 CENTRAL Tel: 719-594-8017 Fax: 719-594-8468 www.aeroflex.com info-ams@aeroflex.com Aeroflex Colorado Springs (Aeroflex) reserves the right to make changes to any products and services herein at any time without notice. Consult Aeroflex or an authorized sales representative to verify that the information in this data sheet is current before using this product. Aeroflex does not assume any responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in writing by Aeroflex; nor does the purchase, lease, or use of a product or service from Aeroflex convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual rights of Aeroflex or of third parties. Our passion for performance is defined by three attributes represented by these three icons: solution-minded, performance-driven and customer-focused 9