Notes
(1) Safety approvals cover frequency range 47-63 Hz.
ACDC
Specification
140 Watts
•120/148 W Convection/Forcedcooled Ratings
•Class I & Class II Construction
•Remote Sense
•5 V Standby Option
•Remote On/Off & Power OK Signals Option
•IT, Industrial & Medical Safety Approvals
•3 Year Warranty
ECM Series
Input
Input Voltage • 80-264 VAC (120-370 VDC), derate output
power <90 VAC (See derating curve)
Input Frequency • 47-400 Hz(1)
Input Current • 2.5 A typical at 115 VAC, full load
1.3 A typical at 230 VAC, full load
Inrush Current • 40 A max at 230 VAC, cold start at 25 °C
Power Factor • EN61000-3-2, class A
Earth Leakage Current • 265 µA max at 264 VAC/60 Hz
0.5/1.1 mA 115/230 VAC at 400 Hz typ.
Input Protection • Internal T5.0 A/250 V fuse in line
and neutral
Output
Output Voltage • 12-48 VDC (see tables)
Output Voltage Trim • ±5%, fan output will track by
same percentage
Initial Set Accuracy • ±1% V1, ±5% V2, ±3% V3
Minimum Load • 0.1 A required on V1 to maintain regulation
of V2
Start Up Delay • 1.5 s max
Start Up Rise Time • 10 ms max
Hold Up Time • 16 ms min at 115 VAC
Drift • ±0.2% after 20 min warm up
Line Regulation • ±0.5% max
Load Regulation • ±1% V1, ±5% V2 & V3 max
Over/Undershoot • 5% typical
Transient Response • 4% max. deviation, recovery to within
1% in 500 µs for a 50-75-50% load
change
Ripple & Noise • 1% pk-pk V1, others 2%, 20 MHz
bandwidth
Overvoltage Protection • 115-140% Vnom, recycle input to reset
Overload Protection • 110-150% V1 only
Short Circuit Protection • Continuous trip and restart (hiccup mode)
Temperature • 0.05%/˚C
Coefficient
Remote Sense • Compensates for 0.5 V total voltage drop
Remote On/Off • Uncommitted isolated optocoupler diode,
(Inhibit/Enable powered diode inhibits V1 & V2
Option -A)
xppower.com
General
Efficiency • 88% typical
Isolation • 4000 VAC Input to Output 2 x MOPP,
1500 VAC Input to Ground 1 x MOPP,
500 VAC Output to Ground
Switching Frequency • 70 kHz typical
Signals (Option -A) • Power OK - open collector,
Remote On/Off, 5 V Standby
MTBF • 220 kHrs to MIL-HDBK-217F at 25 °C, GB
Power Density • 7.2 W/in3
Environmental
Operating Temperature • 0 ˚C to +70 ˚C derate linearly from +50 °C
at 2.5%/˚C to 50% load at +70 °C when
convection-cooled and from +60 °C at
2.5%/°C to 75% load at +70 °C when
forced-cooled. See derating curve.
Cooling • Convection & fan cooled ratings (see tables)
Operating Humidity • 95% RH, non-condensing
Storage Temperature • -40 °C to +85 °C
Operating Altitude • 3000 m
Shock • 30 g pk, half sine, 6 axes
Vibration • 2 g rms, 5 Hz to 500 Hz, 3 axes
EMC & Safety
Low Voltage PSU EMC • EN61204-3, high severity level
Emissions • EN55011/22 level B conducted
EN55011/22 level A radiated
Harmonic Currents • EN61000-3-2, class A
Voltage Flicker • EN61000-3-3
Radiated Immunity • EN61000-4-3, level 3 Perf Criteria A
EFT/Burst • EN61000-4-4, level 3 Perf Criteria A
Surge • EN61000-4-5, installation class 3
Perf Criteria A
Conducted Immunity • EN61000-4-6, level 3 Perf Criteria A
Dips & Interruptions • EN61000-4-11, 30% 10 ms, 60% 100 ms,
100% 5000 ms, Perf Criteria A, B, B
EN60601-1, 30% 500 ms, 60% 100 ms,
100% 10 ms, 100% 5000 ms,
Perf Criteria A, A (with 50% load), A, B
Safety Approvals • EN60601-1, ANSI/AAMI ES60601-1,
CSA22.2 No. 60601-1 per cUL, Including
Risk Management, EN60950-1, UL60950-1
(UL1604 Class 1 Div 2 ECM140US12)
21-May-12
ACDC
3.00
(76.2)
1.90
(48.3)
2.55
(64.8)
4 x ø0.156 (3.96) Mounting Holes
ø0.312 (7.92) Clearance Top & Bottom
0.19 (4.8)
SMD component height
0.25 Faston
Ground Tab
V Adj.
5.00 (127.0)
4.55 (115.6)
0.20 (5.1)
0.20 (5.1)
0.23 (5.7)
1.30
(33.0)
2.50
(63.6)
1.11
(28.3)
0.61
(15.6)
0.14
(3.5)
0.18
(4.6)
0.22 (5.7)
ECM140
Models and Ratings Convectioncooled
Output Connector J2
Pin 1 +V1
Pin 2 +V1
Pin 3 +V1
Pin 4 +V1
Pin 5 RTN
Pin 6 RTN
Pin 7 RTN
Pin 8 RTN
Signal Connector J3
Pin 1 +5V Standby* Pin 6 Inhibit LO*
Pin 2 Logic GND* Pin 7 +Sense
Pin 3 Logic GND* Pin 8 -Sense
Pin 4 Power OK* Pin 9 +Vout
Pin 5 Inhibit HI* Pin 10 -Vout
Mechanical Details
Notes
1. All dimensions in inches (mm). Tolerance .xx = ±0.02 (0.50); .xxx = ±0.01 (0.25)
2. Weight 0.65 lbs (294 g) approx.
3. Vented cover (see derating curves) dimensions are 5.50 x 3.50 x 1.54
(140 x 89 x 39). See longform datasheet for drawing.
See longform datasheet for further information.
Notes
Input Connector J1
Pin 1 Line
Pin 2 Neutral
.25” Faston Earth
Fan Connector J4
Pin 1 Fan +(12 V)
Pin 2 Fan -
J1 mates with Molex housing
09-50-1031 and Molex series
5194 crimp terminals.
J4 mates with Molex housing
22-01-1024 and Molex series
5103 crimp terminals.
J2 mates with Molex housing
09-50-1081 and Molex series
5194 crimp terminals.
*Optional
J3 mates with JST housing PHDR-10VS and JST series
SPHD-001T-P0.5 crimp terminals.
Derating Curves
1. Convection-cooled, output power must not exceed 120 W for
combined V1, V2, & V3
2. For 5 V standby (V3), Power OK & Inhibit, add suffix ‘-A’ to model number.
3. For covered versions, add suffix ‘-C’ to model number or order part no.
ECM140 COVER KIT for standalone cover (see derating curves).
Not suitable for use in class II installations.
Notes
1. 10 CFM airflow achieved with system cooling or with Top Fan assembly.
2. For 5 V standby (V3), Power OK & Inhibit, add suffix ‘-A’ to model number e.g.
ECM140US12-A.
3. For cover with Top Fan assembly please refer to longform datasheet for
mechanical details.
111
96
60
42
120
148
0 +50
+40 +60 +70
Ambient Temperature (ºC)
Convection-cooled with cover
Convection-cooled
Force-cooled >10 CFM
Output Power (W)
Output Power(1) Output Voltage V1 Output Current V1 Fan Output V2 Standby Supply V3(2) Model Number(2,3)
120 W 12.0 VDC 10.0 A 12.0 V/0.5 A 5.0 V/0.5 A ECM140US12
120 W 15.0 VDC 8.0 A 12.0 V/0.5 A 5.0 V/0.5 A ECM140US15
120 W 18.0 VDC 6.6 A 12.0 V/0.5 A 5.0 V/0.5 A ECM140US18
120 W 24.0 VDC 5.0 A 12.0 V/0.5 A 5.0 V/0.5 A ECM140US24
120 W 28.0 VDC 4.2 A 12.0 V/0.5 A 5.0 V/0.5 A ECM140US28
120 W 48.0 VDC 2.5 A 12.0 V/0.5 A 5.0 V/0.5 A ECM140US48
Models and Ratings Forcedcooled
120
100
60
84
148
80 90 264
Input Voltage (VAC)
Convection-cooled
Convection-cooled with cover
10 CFM Force-cooled
Output Power (W)
Output Power(1) Output Voltage V1 Output Current V1 Fan Output V2 Standby Supply V3(2) Model Number(2)
148 W 12.0 VDC 11.7 A 12.0 V/0.5 A 5.0 V/0.5 A ECM140US12
148 W 15.0 VDC 9.3 A 12.0 V/0.5 A 5.0 V/0.5 A ECM140US15
148 W 18.0 VDC 7.7 A 12.0 V/0.5 A 5.0 V/0.5 A ECM140US18
148 W 24.0 VDC 5.8 A 12.0 V/0.5 A 5.0 V/0.5 A ECM140US24
148 W 28.0 VDC 5.0 A 12.0 V/0.5 A 5.0 V/0.5 A ECM140US28
148 W 48.0 VDC 2.9 A 12.0 V/0.5 A 5.0 V/0.5 A ECM140US48