SIDACtor (R) Protection Thyristors SLIC Protection Fixed Voltage Series - DO-214 Pb e3 RoHS Description Fixed Voltage Series DO-214 are uni-directional SIDACtor(R) devices designed to protect SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. The series provides single line protection using a fixed voltage switching device for negative surges. All positive surges are routed through an internal diode to a ground reference. Features and Benefits * Low voltage overshoot * Low on-state voltage Agency Approvals Agency * Does not degrade surge capability after multiple surge events within limit. Agency File Number E133083 * Integrated diode for positive voltage surges * 2nd level interconnect is Pb-free per IPC/JEDEC J-STD-609A.01 * Fails short circuit when surged in excess of ratings Pinout Designation Applicable Global Standards Indicates cathode Schematic Symbol (T/R) (G) * TIA-968-A * GR 1089 Intra-building* * TIA-968-B * IEC 61000-4-5 * ITU K.20/21 Enhanced Level * YD/T 1082 * ITU K.20/21 Basic Level * YD/T 950 * YD/T 993 * GR 1089 Inter-building* *A-rated parts require series resistance Electrical Characteristics Part Number P0641SALRP P0721SALRP P0901SALRP P1101SALRP P1301SALRP P1701SALRP P0641SCLRP P0721SCLRP P0901SCLRP P1101SCLRP P1301SCLRP P1701SCLRP P1101SDLRP P1301SDLRP Marking VDRM @lDRM=5A VS @100V/s IH IS IT VT @IT=2.2 Amps VF V min V max mA min mA max A max V max V max 58 65 75 95 120 160 58 65 75 95 120 160 95 120 77 88 98 130 160 200 77 88 98 130 160 200 130 160 120 120 120 120 120 120 120 120 120 120 120 120 120 120 800 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 P61A P71A P91A P01A P131A P17A P61C P71C P91C P01C P131C P17C P01D P131D Capacitance @1MHz, -2V bias pF pF min pF max 50 45 45 40 40 30 65 60 60 50 50 40 50 50 90 85 80 70 70 55 200 190 180 160 160 130 160 160 Notes: - Absolute maximum ratings measured at TA= 25C (unless otherwise noted). - Devices are uni-directional (c) 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/11/14 1 Fixed Voltage Series, DO-214 SIDACtor (R) Protection Thyristors SLIC Protection Surge Ratings Series IPP ITSM 50/60 Hz di/dt A min A min A/s max 45 75 20 500 175 100 200 30 500 -- 200 -- 50 1000 0.2x310 0.5x700 2 2x10 2x10 2 8x20 1.2x50 2 10x160 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min A 20 150 150 90 50 75 75 C 50 500 400 200 150 200 D -- 1000 800 -- -- -- 1 1 Notes: 1 1 - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40C to +85C - The device must initially be in thermal equilibrium with -40C < TJ < +150C 1 Current waveform in s 2 Voltage waveform in s Thermal Considerations Package Symbol Parameter Value Unit DO-214AA TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C R0JA Thermal Resistance: Junction to Ambient 90 C/W V-I Characteristics tr x td Pulse Waveform VS VDRM VF IPP - Peak Pulse Current - %IPP +I VT -V IDRM +V IH IS IT tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 0 td tr t - Time (s) -I Normalized DC Holding Current vs. Case Temperature 10 IH 8 6 25 C 4 2 IH (TC = 25C) 2.0 14 12 Ratio of Percent of VS Change - % Normalized VS Change vs. Junction Temperature 0 -4 -6 1.8 1.6 1.4 1.0 0.8 0.6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C Junction Temperature (TJ) - C (c) 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/14 25C 1.2 2 Fixed Voltage Series, DO-214 SIDACtor (R) Protection Thyristors SLIC Protection Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) +150C +200C 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3C/sec. Max. TS(max) to TL - Ramp-up Rate 3C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)C Time within 5C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6C/sec. Max. Time 25C to Peak Temp (TP) 8 min. Max. Do not exceed +260C Figure 1 TP Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material Critical Zone TL to TP TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25C to peak) Physical Specifications Lead Material tP Ramp-up Temperature Reflow Condition Time Environmental Specifications UL recognized epoxy meeting flammability classification 94V-0 High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125C or +150C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65C to +150C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65C, 1008 hrs. Thermal Shock 0C to +100C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85C, 168 hrs., 3 reflow cycles (+260C Peak). JEDEC-J-STD-020, Level 1 DO-214 PM for pg. 94 Fixed Voltage Series.eps Part Numbering Part Marking Cathode Indicator P xxx 1 S X L RP DEVICE TYPE P: SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE REEL PACK XXXXX XXXXX L: RoHS COMPLIANT IPP RATING Part number code (refer to Electrical Characteristics table) Date code PACKAGE TYPE (c) 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/14 3 Fixed Voltage Series, DO-214 SIDACtor (R) Protection Thyristors SLIC Protection Dimensions -- DO-214AA Case Temperature Measurement Point Cathode Indicator B D Dimensions C A H E F K G 0.079 (2.0) Millimeters Min Max Min Max A 0.130 0.156 3.30 3.95 B 0.201 0.220 5.10 5.60 C 0.077 0.087 1.95 2.20 D 0.159 0.181 4.05 4.60 E 0.030 0.063 0.75 1.60 F 0.075 0.096 1.90 2.45 G 0.002 0.008 0.05 0.20 H 0.077 0.104 1.95 2.65 K 0.006 0.016 0.15 0.41 Dimensions are in inches (and millimeters). 0.110 (2.8) 0.079 (2.0) Inches Pad Outline (MM) Packing Options Package Type S Description Quantity Added Suffix Industry Standard DO-214AA Tape & Reel Pack 2500 RP EIA-481-D Tape and Reel Specification -- DO-214AA 0.157 (4.0) 0.472 (12.0) Cathode 0.36 (9.2) 0.315 (8.0) 0.059 DIA (1.5) 12.99 (330.0) 0.512 (13.0) Arbor Hole Dia. 0.49 (12.4) (c) 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/14 Cover tape Dimensions are in inches (and millimeters). Direction of Feed 4 Fixed Voltage Series, DO-214 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Littelfuse: P1301SALRP