BD34602FS-ME2 - ROHM SEMICONDUCTOR

Datashee

t

○Product structure:Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays

1/29

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・14・001

Analog Sound Processor Series

6ch Sound Processor for High-Quality Audio

with Built-in Advanced Switch

BD34602FS-M

Description

BD34602FS-M is a 6ch independent volume system. It

is designed to have high-quality sound by improving the

op-amp and optimizing the design layout. In addition, it

is compatible, same package and it has common control

with BD3461FS, therefore replacement from BD3461FS

is easy.

Features

 AEC-Q100 Qualified(Note 1)

 Advanced switch circuit can reduce the switching pop

noise during volume attenuation

 Built-in 6ch independent volume circuit available with

changing by 1dB/Step

 Built-in DIFF amplifier inputs, ideal for external input

 Built-in volume circuit for mixing external signal

available with changing by 1dB/Step

 Package is SSOP-A24. Putting input-terminals

together and output-terminals together can make

PCB layout easier and can makes area of PCB

smaller.

 It is possible to control by 3.3V for I2C-BUS

Controller

(Note1 : Grade 3)

Applications

 Suitable for the Car Audio systems, Car Navigation

systems.

Key Specifications

 Total harmonic distortion : 0.0004%

 Maximum input voltage : 2.35Vrms(Typ)

 Maximum output voltage : 2.35Vrms(Typ)

 Output noise voltage : 1.3μVrms(Typ)

 Residual output noise voltage : 1.3μVrms(Typ)

 Ripple rejection : 80dB (Typ)

 Operating temperature range : -40°C to +85°C

Package W(Typ) x D(Typ) x H(Max)

SSOP-A24 10.00mm x 7.80mm x 2.10mm

SSOP-A24

Ty pical Application Circuit

Figure 1. Application Circuit

2/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Pin Configuration

Descriptions of terminal

Terminal

No.

Terminal

Name Description Terminal

No.

Terminal

Name Description

1 INF1

Front input terminal of 1ch 13 OUTS2

Subwoofer output terminal of 2ch

2 INF2

Front input terminal of 2ch 14 OUTS1

Subwoofer output terminal of 1ch

3 INR1

Rear input terminal of 1ch 15 OUTR2

Rear output terminal of 2ch

4 INR2

Rear input terminal of 2ch 16 OUTR1

Rear output terminal of 1ch

5 INS1

Subwoofer input terminal of 1ch 17 OUTF2

Front output terminal of 2ch

6 INS2

Subwoofer input terminal of 2ch 18 OUTF1

Front output terminal of 1ch

7 EXT1

External input terminal of 1ch 19 VCC

Power supply terminal

8 EXT2

External input terminal of 2ch 20 CS

Chip select terminal

9 EXT3

External input terminal of 3ch 21 SCL

I2C-BUS clock terminal

10 DIFFOUT DIFF amp output terminal 22 SDA I2C-BUS data terminal

11 NIN

DIFF amp negative input terminal 23 GND

GND terminal

12 PIN

DIFF amp positive input terminal 24 FIL

VCC/2 terminal

Figure 2. Pin Configuration

SSOP-A24

(TOP VIEW)

INF1 1

INF2 2

INR1 3

INR2 4

INS1 5

INS2 6

EXT1 7

EXT2 8

EXT3 9

DIFFOUT 10

NIN 11

PIN 12

24 FIL

23 GND

22 SDA

21 SCL

20 CS

18 OUTF1

19 VCC

14 OUTS1

13 OUTS2

17 OUTF2

16 OUTR1

15 OUTR2

3/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Block diagram

Figure 3. Block diagram

●The audible signal inputted from 1pin to 6pin are adjusted independently in volume block, and outputted from

13pin to 18pin.

●The audible signal inputted from 7pin to 9pin are adjusted independently in EXT ATT block, and added independently

to the audible signal inputted from 1pin to 6pin in EXT ON/OFF block, and outputted from 13pin to 18pin.

Absolute maximum ratings (Ta=25°C)

Item Symbol Ratings Unit

Power supply Voltage VCC MAX 10 V

Input voltage Pd 1.0

(Note1) W

Input voltage Vin GND-0.3 to VCC+0.3 V

Operating Temperature Topr -40 to +85 °C

Storage Temperature Tstg -55 to +150 °C

(Note 1) SSOP-A24:Derating at 8.0mW/°C for operating above Ta≥25°C (mounted on 70×70×1.6mm ROHM standard board)

(Note 2) If it is within the operating voltage range, circuit functions and operation are guaranteed within this operating temperature.

Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can

either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore,

it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated

over the absolute maximum ratings.

Operating Range

Item Symbol

MIN TYP MAX Unit

Power Supply VCC 7.0 8.5 9.5 V

Volume★

EXT

ATT

EXT

ATT

EXT

ATT

4/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Electrical characteristic

(Unless otherwise specified, Ta =2 5°C, VCC=8.5V, f=1kHz, Vin=1Vrms, RL=10kΩ, INF1, INF2 Input, Volume=0dB)

BLOCK

Item Symbol

Limit

Unit Conditions

Min Typ Max

GENERAL

Circuit Current upon no signal IQ － 35 50 mA No signal

Voltage gain GV -0.5 0 0.5 dB GV=20log(VOUT/VIN)

Channel balance CB -0.5 0 0.5 dB CB=GV1CH-GV2CH

Total harmonic distortion

+ Noise

THD+N

1k － 0.0004 0.05 % VOUT=1Vrms, f=1kHz

BW=400-30kHz

THD+N

10k － 0.002 0.05 %

VOUT=1Vrms, f=10kHz

BW=400-80kHz

Output noise voltage VNO － 1.3 9 μVrms Rg=0Ω, BW=IHF-A＊

Residual output noise voltage VNOR － 1.3 9 μVrms Volume=-∞

Rg=0, BW=IHF-A＊

Cross-talk between channels

CTC1k － -109 -90 dB

Rg=0Ω, BW=IHF-A＊

CTC1k=20log(VOUT/VIN)

f=1kHz

CTC10k － -103 -90 dB

Rg=0Ω, BW=400-80kHz

CTC10k=20log(VOUT/VIN)

f=10kHz

Ripple rejection RR 55 80 － dB

f=100Hz, VCCIN=100mVrms

RR=20log(VCCIN/VOUT)

VOLUME

Input impedance RIN V 70 100 130 kΩ

Maximum input voltage

VIM1k 2 2.35 － Vrms VIM at THD+N(VOUT)=1%

BW=400-30kHz, f=1kHz

VIM10k 2 2.35 － Vrms VIM at THD+N(VOUT)=1%

BW=400-80kHz, f=10kHz

Maximum gain GV BST 22 23 24 dB

Gain=23dB, VIN=100mVrms

GV BST=20log(VOUT/VIN)

Maximum attenuation

GV MIN1k － -109 -90 dB

Volume=-∞

GV MIN1k=20log(VOUT/VIN)

BW=IHF-A＊, f=1kHz

GV MIN10k － -103 -90 dB

Volume=-∞

GV MIN10k=20log(VOUT/VIN)

BW=400-80kHz, f=10kHz

Gain set error GV ERR -1.0 0 1.0 dB

Gain=+1～+23dB

Attenuation set error 1 GV ERR1 -0.5 0 0.5 dB ATT=-1～-15dB

Attenuation set error 2 GV ERR2 -1.0 0 1.0 dB

ATT=-16～-47dB

Attenuation set error 3 GV ERR3 -2.0 0 2.0 dB ATT=-48～-79dB

Output impedance R OUT 70 100 130 Ω Vin=100mVrms

Maximum output voltage

VOM1k 2 2.35 － Vrms THD+N=1%

BW=400-30kHz, f=1kHz

VOM10k 2 2.35 － Vrms THD+N=1%

BW=400-80kHz, f=10kHz

EXT

ATT

Input impedance RIN M 70 100 130 kΩ

Maximum attenuation GM MIN － -90 -80 dB

GM MIN=20log(VOUT/VIN)

BW=IHF-A＊, ATT=-∞

DIFF

Input impedance RIN D 70 100 130 kΩ

Common mode rejection ratio CMRR 50 65 － dB

PIN and NIN input

CMRR=20log10(VIN/VOUT)

BW=IHF-A＊

Phase between input / output is same

＊VP-9690(Average value detection, effective value display) filter by Panasonic is used for * measurement.

5/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Typical Performance Curve(s)

Figure 5. Gain vs Frequency

-10

-8

-6

-4

-2

0

2

4

6

8

10

10 100 1000 10000 100000

Frequency [Hz]

Gain [dB]

Figure 4. VCC vs Circuit Current upon no signal

20

25

30

35

40

45

50

7.0 7.5 8.0 8.5 9.0 9.5

VC C [V]

Circuit Current upon no signal [mA]aa

0.0001

0.001

0.01

0.1

1

0.001 0.01 0.1 1 10

Vin [Vrm s ]

THD+N [%]

0.001

0.01

0.1

1

10

Vo [Vrms]

Figure 6. THD+N vs VIN / VO Figure 7. Volume Gain vs Frequency

(Volume Gain = +23dB ～ 0dB)

10kHz

1 kHz

100Hz

-2

0

2

4

6

8

10

12

14

16

18

20

22

24

10 100 1000 10000 100000

Frequency[Hz]

Volume Gain [dB]

1k 10k 100k

100 10

1k 10k 100k

100 10

6/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

(Note) The measurement results of Figure 7 to Figure 11 used by 80kHz LPF.

Figure 8. Volume Gain vs Frequency

(Volume Gain = 0dB ～ -40dB)

Figure 9. Volume Gain vs Frequency

(Volume Gain = -40dB ～ -79dB)

-42

-40

-38

-36

-34

-32

-30

-28

-26

-24

-22

-20

-18

-16

-14

-12

-10

-8

-6

-4

-2

0

2

10 100 1000 10000 100000

Frequency[Hz]

Volume Gain [dB]

-82

-80

-78

-76

-74

-72

-70

-68

-66

-64

-62

-60

-58

-56

-54

-52

-50

-48

-46

-44

-42

-40

-38

10 100 1000 10000 100000

Frequency[Hz]

Volume Gain [dB]

-42

-40

-38

-36

-34

-32

-30

-28

-26

-24

-22

-20

-18

-16

-14

-12

-10

-8

-6

-4

-2

0

2

10 100 1000 10000 100000

Frequency[Hz]

EXT ATT Gain [dB

]

-82

-80

-78

-76

-74

-72

-70

-68

-66

-64

-62

-60

-58

-56

-54

-52

-50

-48

-46

-44

-42

-40

-38

10 100 1000 10000 100000

Frequency[Hz]

EXT ATT Gain [dB

]

1k 10k 100k

100 10

1k 10k 100k

100 10

1k 10k 100k

100 10

1k 10k 100k

100 10

Figure 10. EXT ATT Gain vs Frequency

(EXT ATT Gain = 0dB ～ -40dB)

Figure 11. EXT ATT Gain vs Frequency

(EXT ATT Gain = -40dB ～ -79dB)

7/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

ｔBUF

：4us

ｔHD;STA

：2us

ｔHD;DAT

：1us

ｔLOW

：3us

ｔHIGH

：1us

ｔSU;DAT

：1us

ｔSU;STO

：2us

SCL clock frequency：250kHz

SCL

SDA

CONTROL SI GNAL SPECIFICATION

(1) Electrical specifications and timing for bus lines and I/O stages

Figure 12. Definition of timing on the I2C-BUS

Table 1 Characteristics of the SDA and SCL bus lines for I2C-BUS devices

Item Symbol

Fast-mode I

2

C-BUS) Unit

Min Max

1 SCL clock frequency fSCL 0 400 kHz

2 Bus free time between a STOP and START condition tBUF 1.3 － μs

3 Hold time (repeated) START condition. After this period, the first clock

pulse is generated tHD;STA 0.6 － μs

4 LOW period of the SCL clock tLOW 1.3 － μs

5 HIGH period of the SCL clock tHIGH 0.6 － μs

6 Set-up time for a repeated START condition tSU;STA 0.6 － μs

7 Data hold time tHD;DAT 0 － μs

8 Data set-up time tSU;DAT 100 － ns

9 Set-up time for STOP condition tSU;STO 0.6 － μs

All values referred to VIH min. and VIL max. Levels (see Table 2).

Table 2 Input/Output Characteristics of the SDA and SCL terminal for I2C-BUS devices

Item Symbol Fast-mode I2C-BUS) Unit

Min Max

10 LOW level input voltage VIL -0.5 1 V

11 HIGH level input voltage VIH 2.3 - V

12 Pulse width of spikes which must be suppressed by the input filter. tSP 0 50 ns

13 LOW level output voltage : At 3mA sink current VOL1 0 0.4 V

14 Input current each I/O pin with an input voltage between 0.4V and 4.5

VDDmax. Ii -10 10 μA

Table 3 Input Characteristics of the CS terminal (Slave Address can be changed by the setting of CS terminal)

Item Symbol Min Max

Unit

1 CS = Low：Slave Address 80 hex VCSL -0.5 1 V

2 CS = High：Slave Address 84 hex VCSH 2.3 VCC V

STOP condition START condition

Repetition

START condition

STOP condition

SDA

S

SCL

tLOW

tHD;DAT

P

tHD;STA tHIGH

tBUF

tSU;DAT tSU;ST A tSU;STO

tSP

tHD;STA

Sr

P

0.3V DD

=1V

0.7VDD

=2.3V

Figure 13.

A command timing example in

the I2C-BUS data transmission

8/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

(2) I2C-BUS FORMAT

MSB LSB MSB LSB MSB LSB

S Slave Address A Select Address A Data A P

1bit 8bit 1bit 8bit 1bit 8bit 1bit 1bit

S = Start conditions (Recognition of start bit)

Slave Address = Recognition of Slave Address. 7 bits in upper order are voluntary.

The least significant bit is “L” due to writing.

A = ACKNOWLEDGE bit (Recognition of acknowledgement)

Select Address = Select every of volume, bass and treble.

Data = Data on every volume and tone.

P = Stop condition (Recognition of stop bit)

(3) I2C-BUS Interface Protocol

1）Basic form

S Slave Address A Select Address A Data A P

MSB LSB MSB LSB MSB LSB

2）Automatic increment (For an assigned Select Address increases (+1) according to the number of data.)

S Slave Address A Select Address A Data1 A Data2 A ････ DataN A P

MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB

No.1. Data1 is set as data of address specified by Select Address.

No.2. Data2 is set as data of next address from the address specified by No.1.

No.3. DataN is set as data of address incremented N-1 times from the address specified by No.1.

The Select Address is circulated by the automatic increment function, as shown below (hex).

3）Configuration unavailable for transmission (In this case, only Select Address1 is set.

S Slave Address A Select Address1 A Data A Select Address 2 A Data A P

MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB

（Note）If any data is transmitted as Select Address 2 next to data,

it is recognized as data, not as Select Address 2.

(4) Slave Address

Because the Slave Address can be changed by the setting of CS, it is possible to use two chips

at the same time on identical BUS.

CS Terminal Voltage Condition A6 A5 A4 A3 A2 A1 A0 R/W Hex

CS = Low : -0.5V to 1.0V 1 0 0 0 0 0 0 0 80

CS = High : 2.3V to VCC 1 0 0 0 0 1 0 0 84

Establish the voltage of CS terminal in the condition to have been defined.

→

01

→

28

→

29

→

2A

→

2B

→

2C

→

2D

→

30

→

31

→

32

→

33

→

34

→

35

9/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

(5) Select Address & Data

Items to be set

Select

Address

(hex)

MSB

Data

LSB

D7 D6 D5 D4 D3 D2 D1 D0

EXT ATT 1dB/Step

Enable 01 0 0 0 0

EXT ATT

1dB/Step

Enable

1 0 0

Advanced Switch

Time of

EXT ON/OFF

02 0

Advanced Switch

Time of

EXT ON/OFF 2

Advanced Switch

Time of

EXT ON/OFF 1

0 0

Volume Gain

Front 1ch (F1) 28 Volume Gain (F1)

Volume Gain

Front 2ch (F2) 29 Volume Gain (F2)

Volume Gain

Rear 1ch (R1) 2A Volume Gain (R1)

Volume Gain

Rear 2ch (R2) 2B Volume Gain (R2)

Volume Gain

Subwoofer 1ch (S1) 2C Volume Gain (S1)

Volume Gain

Subwoofer 2ch (S2) 2D Volume Gain (S2)

EXT1 ON/OFF 30 EXT1

S2

EXT1

S1

EXT1

R2

EXT1

R1

EXT1

F2

EXT1

F1 0 0

EXT2 ON/OFF 31 EXT2

S2

EXT2

S1

EXT2

R2

EXT2

R1

EXT2

F2

EXT2

F1 0 0

EXT3 ON/OFF 32 EXT3

S2

EXT3

S1

EXT3

R2

EXT3

R1

EXT3

F2

EXT3

F1 0 0

EXT 1 ATT Gain 33 EXT1 ATT Gain

EXT 2 ATT Gain 34 EXT2 ATT Gain

EXT 3 ATT Gain 35 EXT3 ATT Gain

Test Mode F0 0 0 0 0 0 0 0 0

System Reset FE 1 0 0 0 0 0 0 1

Advanced switch

Note(Please be sure to follow the instructions)

It is written with “0”, “1” by the above table, please set “0”, “1” in the same way as above table.

In case of different settings, there is possibility of cause unintended behavior.

Instructions of the data format

1. In function changing of the hatching part, it works Advanced switch(In detail, please refer p13).

2. Upon continuous data transfer, the Select Address is circulated by the automatic increment function, as shown

below(hex).

※Select Address 02(hex) is not included in the automatic increment to keep BD346 1F S software compatible.

3. When changing “EXT = ON/OFF”, it is not corresponded for advance switch. Therefore, please do the measure that

applies mute on the side of a set at the time of these setting changes

→

01

→

28

→

29

→

2A

→

2B

→

2C

→

2D

→

30

→

31

→

32

→

33

→

34

→

35

10/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Explanation of each Select Address

Figure.14 Block diagram

It is able to control to 1 to 4 in block diagram by each Select Address. About detail explanation is Follow as.

●The audible signal inputted from 1pin to 6pin are adjusted independently in volume block(2 in block diagram).

< Select Address 28, 29, 2A, 2B, 2C 2D(hex)：Volume >

It is able to select adjustment of audible signal in volume block(+23dB to -79dB, -∞).

●The audible signal inputted from 7pin to 9pin are adjusted independently in EXT ATT block(4 in block diagram),

and added independently to the audible signal inputted from 1pin to 6pin in EXT ON/OFF block.

(EXT ON/OFF① block (3 in block diagram) : path select, EXT ON/OFF② block (1 in block diagram) : add)

< Select Address 01(hex)：EXT ATT 1dB/Step Enable >

About adjustment of audible signal in EXT ATT block (4 in block diagram), it is able to select 1dB/Step mode ON/OFF.

< Select Address 02(hex)：Advanced Switch Time of EXT ON/OFF >

Advanced Switch function is applied to EXT ON/OFF for prevention switching pop-noise. (About Advanced Switch,

refer to 15page) It is able to select switching time of Advanced Switch by Select Address 02(hex).

< Select Address 30, 31, 32(hex)：EXT ON/OFF >

The audible signal inputted from 7pin to 9pin is added to the audible signal inputted from 1pin to 6pin.

It is able to select path of above combination (1 and 3 in block diagram).

< Select Address 33, 34, 35(hex)：EXT ATT >

It is able to select adjustment (0dB to -79dB, -∞) of audible signal in EXT ATT block (3 in block diagram).

10 11 12

22 21 20 19 18 17 16 15 14 13

3456789

24 23

1 2

Volume

VCC/2

Volume

100k

GND

Volume

+-

100k 100k

2. Volume (+23dB ～ -79dB, -∞)

(Select Address 28,29,2A,2B,2C,2Dhex)

100k 100k 100k 100k 100k 100k 100k 100k

I2C-BUS LOGIC

VCCSDA SCL CSGNDFIL

DIFFOUT NIN PIN

INF1 INF2 INR1 INR2 INS1 INS2 EXT1 EXT2 EXT3

OUTS2OUTS1OUTR2OUTR1OUTF2OUTF1

EXT

ATT

EXT

ATT

EXT

ATT

3. EXT ON/OFF①

(Select Address 30,31,32hex)

4. EXT ATT (0dB ～ -79dB, -∞)

(Select Address 01,33,34,35hex)

1. EXT ON/OFF②

(Select Address 02,30,31,32hex)

11/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Select Address 01(hex) EXT ATT 1dB/Step Enable

MODE

MSB EXT ATT 1dB/Step Enable LSB

D7 D6 D5 D4 D3 D2 D1 D0

OFF 0 0 0 0 0 0 0 0

ON 1

Select Address 02(hex) Advanced Switch Time of EXT ON/OFF

MODE

MSB Advanced Switch Time of EXT ON/OFF 1 LSB

D7 D6 D5 D4 D3 D2 D1 D0

11.2msec

0 Advanced Switch

Time of EXT ON/OFF 2

0 0

4.7msec 0 1

7.2msec 1 0

14.4msec 1 1

Select Address 02(hex) Advanced Switch Time of EXT ON/OFF

MODE

MSB Advanced Switch Time of EXT ON/OFF 2 LSB

D7 D6 D5 D4 D3 D2 D1 D0

x1

0

0 0 0

Advanced Switch

Time of

EXT ON/OFF 1

0 0

x2 0 0 1

x3 0 1 0

x4 0 1 1

x5 1 0 0

x6 1 0 1

x7 1 1 0

x8 1 1 1

Select Address 28, 29, 2A, 2B, 2C 2D(hex) Volume

Gain & ATT

MSB Volume Gain/Attenuation LSB

D7 D6 D5 D4 D3 D2 D1 D0

Prohibition ※

0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 1

: : : : : : : :

0 1 1 0 1 0 0 0

23dB 0 1 1 0 1 0 0 1

22dB 0 1 1 0 1 0 1 0

21dB 0 1 1 0 1 0 1 1

: : : : : : : : :

-77dB 1 1 0 0 1 1 0 1

-78dB 1 1 0 0 1 1 1 0

-79dB 1 1 0 0 1 1 1 1

Prohibition ※

1 1 0 1 0 0 0 0

: : : : : : : :

1 1 1 1 1 1 1 0

-∞dB 1 1 1 1 1 1 1 1

: Initial condition

12/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Select Address 30, 31, 32(hex) EXT ON/OFF

MODE

MSB EXT F1 LSB

D7 D6 D5 D4 D3 D2 D1 D0

OFF EXT

S2

EXT

S1

EXT

R2

EXT

R1

EXT

F2

0 0 0

ON 1

MODE

MSB EXT F2 LSB

D7 D6 D5 D4 D3 D2 D1 D0

OFF EXT

S2

EXT

S1

EXT

R2

EXT

R1

0 EXT

F1 0 0

ON 1

MODE

MSB EXT R1 LSB

D7 D6 D5 D4 D3 D2 D1 D0

OFF EXT

S2

EXT

S1

EXT

R2

0 EXT

F2

EXT

F1 0 0

ON 1

MODE

MSB EXT R2 LSB

D7 D6 D5 D4 D3 D2 D1 D0

OFF EXT

S2

EXT

S1

0 EXT

R1

EXT

F2

EXT

F1 0 0

ON 1

MODE

MSB EXT S1 LSB

D7 D6 D5 D4 D3 D2 D1 D0

OFF EXT

S2

0 EXT

R2

EXT

R1

EXT

F2

EXT

F1 0 0

ON 1

MODE

MSB EXT S2 LSB

D7 D6 D5 D4 D3 D2 D1 D0

OFF 0 EXT

S1

EXT

R2

EXT

R1

EXT

F2

EXT

F1 0 0

ON 1

Select Address 33, 34, 35(hex) EXT ATT ※Select Address 01(hex), D3 = 0, (EXT 1dB Enable = OFF)

Gain MSB EXT Attenuation LSB

D7 D6 D5 D4 D3 D2 D1 D0

0dB

0 0 0 0 0

0 0 0

-8dB 0 0 1

-16dB 0 1 0

-24dB 0 1 1

-32dB 1 0 0

-48dB 1 0 1

-64dB 1 1 0

-∞dB 1 1 1

Select Address 33, 34, 35(hex) EXT ATT ※Select Address 01(hex), D3 = 1, (EXT 1dB Enable = ON)

Gain & ATT MSB EXT Attenuation LSB

D7 D6 D5 D4 D3 D2 D1 D0

0dB 1 0 0 0 0 0 0 0

-1dB 1 0 0 0 0 0 0 1

-2dB 1 0 0 0 0 0 1 0

: : : : : : : : :

-77dB 1 1 0 0 1 1 1 0

-78dB 1 1 0 0 1 1 1 0

-79dB 1 1 0 0 1 1 1 1

Prohibition ※

1 1 0 1 0 0 0 0

: : : : : : : :

1 1 1 1 1 1 1 0

-∞ 1 1 1 1 1 1 1 1

: Initial condition

13/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

(6) About power on reset

At on of supply voltage circuit made initialization inside IC is built-in. Please send data to all address as initial data

at supply voltage on. And please supply mute at set side until this initial data is sent.

Item Symbol Limit Unit Condition

Min Typ Max

Rise time of VCC Trise 33 －－ μsec VCC rise time from 0V to 5V

VCC voltage of release

power on reset Vpor － 4.1 － V

(7) About start-up and power off sequence on IC

In power supply off, please set a register state of the IC as follows.

・Volume Gain /Attenuation = MINF (SelectAddress28,29,2A,2B,2C,2D(hex), Data = FF(hex))

・EXT1,2,3 ON/OFF = OFF (SelectAddress30,31,32(hex), Data = 00(hex))

Figure 15. The sequence of power supply ON/OFF

14/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

・Select Address 28, 29, 2A, 2B, 2C 2D(hex) Volume (Gain = +23dB ～ -79dB, -∞)

・Select Address 33, 34, 35(hex) EXT ATT (Gain = 0dB ～ -79dB, -∞)

※Select Address 01(hex), D3 = 1, (EXT 1dB Enable = ON)

Volume gain attenuation

(dB) D7 D6 D5 D4 D3 D2 D1 D0 (dB) D7 D6 D5 D4 D3 D2 D1 D0

+23 0 1 1 0 1 0 0 1 -29 1 0 0 1 1 1 0 1

+22 0 1 1 0 1 0 1 0 -30 1 0 0 1 1 1 1 0

+21 0 1 1 0 1 0 1 1 -31 1 0 0 1 1 1 1 1

+20 0 1 1 0 1 1 0 0 -32 1 0 1 0 0 0 0 0

+19 0 1 1 0 1 1 0 1 -33 1 0 1 0 0 0 0 1

+18 0 1 1 0 1 1 1 0 -34 1 0 1 0 0 0 1 0

+17 0 1 1 0 1 1 1 1 -35 1 0 1 0 0 0 1 1

+16 0 1 1 1 0 0 0 0 -36 1 0 1 0 0 1 0 0

+15 0 1 1 1 0 0 0 1 -37 1 0 1 0 0 1 0 1

+14 0 1 1 1 0 0 1 0 -38 1 0 1 0 0 1 1 0

+13 0 1 1 1 0 0 1 1 -39 1 0 1 0 0 1 1 1

+12 0 1 1 1 0 1 0 0 -40 1 0 1 0 1 0 0 0

+11 0 1 1 1 0 1 0 1 -41 1 0 1 0 1 0 0 1

+10 0 1 1 1 0 1 1 0 -42 1 0 1 0 1 0 1 0

+9 0 1 1 1 0 1 1 1 -43 1 0 1 0 1 0 1 1

+8 0 1 1 1 1 0 0 0 -44 1 0 1 0 1 1 0 0

+7 0 1 1 1 1 0 0 1 -45 1 0 1 0 1 1 0 1

+6 0 1 1 1 1 0 1 0 -46 1 0 1 0 1 1 1 0

+5 0 1 1 1 1 0 1 1 -47 1 0 1 0 1 1 1 1

+4 0 1 1 1 1 1 0 0 -48 1 0 1 1 0 0 0 0

+3 0 1 1 1 1 1 0 1 -49 1 0 1 1 0 0 0 1

+2 0 1 1 1 1 1 1 0 -50 1 0 1 1 0 0 1 0

+1 0 1 1 1 1 1 1 1 -51 1 0 1 1 0 0 1 1

0 1 0 0 0 0 0 0 0 -52 1 0 1 1 0 1 0 0

-1 1 0 0 0 0 0 0 1 -53 1 0 1 1 0 1 0 1

-2 1 0 0 0 0 0 1 0 -54 1 0 1 1 0 1 1 0

-3 1 0 0 0 0 0 1 1 -55 1 0 1 1 0 1 1 1

-4 1 0 0 0 0 1 0 0 -56 1 0 1 1 1 0 0 0

-5 1 0 0 0 0 1 0 1 -57 1 0 1 1 1 0 0 1

-6 1 0 0 0 0 1 1 0 -58 1 0 1 1 1 0 1 0

-7 1 0 0 0 0 1 1 1 -59 1 0 1 1 1 0 1 1

-8 1 0 0 0 1 0 0 0 -60 1 0 1 1 1 1 0 0

-9 1 0 0 0 1 0 0 1 -61 1 0 1 1 1 1 0 1

-10 1 0 0 0 1 0 1 0 -62 1 0 1 1 1 1 1 0

-11 1 0 0 0 1 0 1 1 -63 1 0 1 1 1 1 1 1

-12 1 0 0 0 1 1 0 0 -64 1 1 0 0 0 0 0 0

-13 1 0 0 0 1 1 0 1 -65 1 1 0 0 0 0 0 1

-14 1 0 0 0 1 1 1 0 -66 1 1 0 0 0 0 1 0

-15 1 0 0 0 1 1 1 1 -67 1 1 0 0 0 0 1 1

-16 1 0 0 1 0 0 0 0 -68 1 1 0 0 0 1 0 0

-17 1 0 0 1 0 0 0 1 -69 1 1 0 0 0 1 0 1

-18 1 0 0 1 0 0 1 0 -70 1 1 0 0 0 1 1 0

-19 1 0 0 1 0 0 1 1 -71 1 1 0 0 0 1 1 1

-20 1 0 0 1 0 1 0 0 -72 1 1 0 0 1 0 0 0

-21 1 0 0 1 0 1 0 1 -73 1 1 0 0 1 0 0 1

-22 1 0 0 1 0 1 1 0 -74 1 1 0 0 1 0 1 0

-23 1 0 0 1 0 1 1 1 -75 1 1 0 0 1 0 1 1

-24 1 0 0 1 1 0 0 0 -76 1 1 0 0 1 1 0 0

-25 1 0 0 1 1 0 0 1 -77 1 1 0 0 1 1 0 1

-26 1 0 0 1 1 0 1 0 -78 1 1 0 0 1 1 1 0

-27 1 0 0 1 1 0 1 1 -79 1 1 0 0 1 1 1 1

-28 1 0 0 1 1 1 0 0 -∞ 1 1 1 1 1 1 1 1

:Initial condition

15/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

About advanced switch circuit

【1】Advanced switch technology

1-1. Advanced switch effects

Advanced switch technology is Rohm original switching pop noise prevention technology. The audible signal is

discontinuous during the gain switching instantly which cause the noise to occur. This Advanced switch circuit will prevent

this discontinuous signal by completing the signal waveform and will significantly reduce the noise.

This Advanced switch technology will start the switching when received the signal sent from the micon.

At any constant time, the switching waveform is shown as above figure. This IC will optimally operate by internally

processing the data sent from the micon to prevent the switching shock.

However, sometimes the switching waveform is not like the intended form depends on the transmission timing.

Therefore, below is the example of the relationship between the transmission timing and actual switching time. Please

consider this relationship for the setting.

1-2. The kind of the Transferring Data

・Data setting other than Advanced switch supported items

( P.9 Select Address and data Data format without hatching)

There is no particular rule about transferring data.

・Advanced switch supported items data setting

(P.9 Select Address and data Data format with hatching)

There is no particular rule about transferring data, but Advanced switch must follow the switching sequence as

mentioned in【2】.

※ Advanced switch supported blocks are “Volume” and ”EXT ON/OFF”(In detail, please refer p9).

Figure 16. Advanced switch wave

16/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

【2】Data transmission of Advanced switch supported items

2-1. Switching time of Advanced switch

Switching time includes [Twait(Wait time)], [Tsft(A→B switching time)] and [Tsft(B→A switching time)].

25msec is needed per 1 switching. (Tsoft = Twait + 2 * Tsft, Twait=2.3msec, Tsft=11.2msec)

Figure 17. About Advanced switching time

In Figure 8, Start/Stop state is expressed as “A” and temporary state is expressed as “B”.

The switching sequence of Advance switch will be, A(start)→B→A(stop), thus switching will not stop at B state.

In other words, switching is performed from A(Initial gain)→B(set gain→A(set gain) when switching from initial gain to set

gain.

It is possible to change the switching time of Advanced switch time by setting the EXT Advanced switch multi sel and

Advanced Switch Time of EXT at select Address2.

If only EXT ON/OFF is performed in all Advanced switch operation, the switching time of Advanced switch is determined

by EXT Advanced switch multi sel and Advanced Switch Time of EXT.

For example

EXT Advanced switch multi sel is set to x8 and Advanced Switch Time of EXT is set to 14.4msec

In this case, the switching time of Advanced switch is determined as below.

EXT Advanced switch multi sel x Advanced Switch Time of EXT = 115.2msec

This is equal to switching time of A→B or B→A(Tsft).

As mentioned in Figure 11 (Start sequence of Advanced switch), each ch(6channels) volume and EXT ON/OFF switch at

the same timing. When each ch(6channels) volume switches at the same time EXT ON/OFF operation is performed,

switching time of each ch(6channels) volume will be the same as EXT ON/OFF switching set by calculation above. In other

words, switching time of EXT ON/OFF has higher priority than that of the 6channels volume

Even if switching time of EXT ON/OFF is set by calculation above, when EXT ON/OFF switching is not being performed,

switching time of each ch(6channels) volume is determined as Tsft＝11.2msec. Please exercise caution when setting the

switching time of Advanced switch.

W

Advanced Switch Time (Tsoft)

[A→B switching time]

=Tsft

[B→A switching time]

=Tsft

[wait time]

=Twait

Current XdB

Send YdB Change YdB

B → AA → B

17/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

2-2. Explanation on data transmission’s timing and switching operation.

The following examples show the time chart from the time a data is transmitted until the switching starts.

■ Transmission example 1

This is an example when transmitting data in same block with enough transmission interval.

This enough interval refers to the tolerance margin time of Tsoft multiplied by 1.4.

■ Transmission example 2

This is an example when the transmission interval is not enough (smaller than transmission example 1).

When the data is transmitted during the first switching operation, the second data transmission will continue after

complete the first switching. In this case, there is no wait time (Twait) before the second switching.

■ Transmission example 3

This is an example when transmission interval is even smaller (smaller than transmission example 2).

When the data is transmitted during the first switching, and it is during A→B switching operation, if the transmitted

data is volume, switching of new data is performed at B→A timing

If the transmitted data is EXT ON/OFF switching, when other switching data is sent during A→B switching, switching’s

will be the same as Transmission example 2

80 28 80

slave select data ack

I2C-BUS

Advanced Switch time W

(F1 0dB)

80 28 FF

(F1 -∞dB)

Tsoft * 1.4 msec

F1 output

WB → AA → B B → AA → B

80 28 80

slave select data ack

I2C-BUS

Advanced Switch time

(F1 0dB)

80 28 FF

(F1 -∞dB)

F1 output

WB → AA → B B → AA → B

80 28 80

slave select data ack

I2C-BUS

Advanced Switch time

(F1 0dB)

80 28 FF

(F1 -∞dB)

F1 output

WB → AA → B

80 30 04

slave select data ack

I2C-BUS

Advanced Switch time

(EXT1 F1 ON)

80 31 04

F1 output

WB → AA → B

(EXT2 F1 ON)

B → AA → B

18/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

About data transmission to multi-channels, there is a caution. It is possible that Lch and Rch in same block(Front/Rear/Sub)

can be switched at the same timing. For example, when the data transmission is set as the figure below, it is possible that

OUTF1 and OUTF2 can be switched at the same timing(Data  is sent for FL (Lch) and data  is sent for FR (Rch)).

Please take note that Twait is wait time for starting switching and designed to 2.3msec. (Considering fluctuation of element,

Twait may change from 1.2msec (Min.) to 4.6msec (Max.).

Figure 18. The operation during multi-channels (1ch, 2ch) data transmission (smaller than Twait interval).

Next, when data  is not transmitted during the Twait, the switching operation is as following figure.

Figure 19. The operation during multi-channels (1ch, 2ch) data transmission (larger than Twait interval).

80 28 ｘｘ

I2C-BUS

Advanced Switch time WB → AA → B

①②

Output F1 Initial Initial → ①

②

T②-①　＜ Twait

80 29 ｘｘ

Output F2 Initial Initial → ②

①

80 28 ｘｘ

I2C-BUS

Advanced Switch time WB → AA → B

①②

Output F1 Initial Initial → ①

②

T②-①　＞ Twait

80 29 ｘｘ

Output F2 Initial Initial → ②

①

B → AA → B

19/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

2-3. Multi-blocks data transmission timing and switching operation.

In case the data is transmitted to the multi-blocks, the processing is performed internally by BS unit.

Micro step volume starting order is determined by BS unit.

■Transmission example 1

※It is the same even if it transfers data in auto increment mode.

There are no timing regulations of I2C-BUS transferring data. But the timing of a change start after the end of the present

change. In addition, the timing of Advanced switch is not depended of a transferring data turn, but conforms in turn of the

following figure.

Figure 20. The turn of Advanced switch start

※The block in the same group can start the Advanced switch in the same time.

80 28 80

slave select data ack

I2C-BUS

Advanced Switch time W

(F1 0dB)

80 2A 80

(R1 0dB)

F1 output

B → AA → B B → AA → B

80 2C 80

(S1 0dB)

B → AA → B

F1 Advanced Switch R1 Advanced Switch S1 Advanced Switch

R1 output

S1 output

20/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

■Transmission example 2

In case of the transmission order is different with actual switching order.

During Front switching, in case of Front/Rear/SW continuously received, Rear and SW switching are the priority.

If you want the switching starts as the data transmission order, please transmit the next data after current switching is

ended.

■Transmission example 3

For Refresh data, the IC will internally judge that there is no difference with the current data setting and therefore gain

switching operation will not start.

Continuing the Refresh data and transmit the other block data.

Advanced Switch time

①②

Output F1 Initial Initial → ①

80 xx ｘｘ

Output R1 Initial

①

WB → AA → B B → AA → B B → AA → B

③④

ex：①F1 -6dB

②F1 -20dB

③S1 -6dB

④R1 -6dB

F1 Advanced Switch R1 Advanced Switch S1 Advanced Switch F1 Advanced Switch

B → AA → B

Initial → ④

①→② ②

④

Output S1 Initial Initial → ③ ③

I2C-BUS

80 28 80

slave select data ack

Advanced Switch time W

(F1 0dB)

80 2A 80

(R1 0dB)

B → AA → B B → AA → B

F1 Advanced Switch R1 Advanced Switch

80 28 80

(F1 0dB)

Refresh Data

I2C-BUS

21/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Application Circuit Diagram

Figure 21. Application Circuit Diagram

Notes on wiring

①Please connect the decoupling capacitor of the power supply in the shortest distance as much as possible to VCC and

GND, VEE.

②Lines of GND shall be one-point connected.

③Wiring pattern of Dagital shall be away from the analog unit and cross-talk is not acceptable.

④Lines of SCL and SDA of I2C BUS shall not be parallel if possible. The lines shall be shielded, if they are adjacent to

each other.

⑤Lines of analog input shall not be parallel if possible. The lines shall be shielded, if they are adjacent to each other.

UNIT

RESISTANCE: Ω

CAPACITANCE: F

22/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Power Dissipation

Thermal design for the IC

Temperature has great influence to the IC characteristics, and exceeding the absolute maximum ratings may degrade

and damage the IC. A proper consideration must be given from two points, immediate damage and long-term reliability

of operation.

Figure 22. Temperature Derating Curve

Note) Values mentioned above are based on actual measurement, and not guaranteed.

Note) Power dissipation value varies depending to the board on which the IC is mounted.

SSOP-A24

1.5

1.0

0.5

0.0

0 25 50 75 100 125

150

Ambient Temperature Ta(°C)

Power Dissipation Pd (W）

1.0W

Measurement condition: ROHM Standard board

Board Size:70×70×1.6(㎣)

Material:A FR4 grass epoxy board

(3% or less of copper foil area)

θja = 125°C /W

85

23/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Terminal Equivalent Circuit and Description

Terminal

No.

Terminal

Name

Terminal

Voltage Equivalent Circuit Terminal Description

1

2

3

4

5

6

7

8

9

11

12

INF1

INF2

INR1

INR2

INS1

INS2

EXT1

EXT2

EXT3

NIN

4.25V

GND

VCC

100K Ω

A terminal for signal input.

The input impedance is 100kΩ(typ).

10

13

14

15

16

17

18

DIFFOUT

OUTS2

OUTS1

OUTR2

OUTR1

OUTF2

OUTF1

4.25V

A terminal for fader output.

22 SCL －

1.65V

VCC

GND

SCL

A terminal for clock input of I2C-BUS.

23 SDA －

1.65V

VCC

GND

SDA

A terminal for data input of I

2

C-BUS.

20 CS － VCC

GND

CS

1.65V

CS Input Terminal.

A terminal for Slave Address selection.

“CS” is “High”→Slave Address “84 H”

“CS” is “Low”→ Slave Address “80 H”

The figure in the pin explanation and input/output equivalent circuit is reference value, it’s doesn’t guarantee the value.

24/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Terminal

No.

Terminal

Name

Terminal

Voltage Equivalent Circuit Terminal Description

19 VCC 8.5V Power supply terminal.

23 GND 0V

Ground terminal.

24 FIL 4.25V VCC

GND

50kΩ

FIL

50kΩ

1/2 VCC terminal.

Voltage for reference bias of analog signal

system. The simple precharge circuit and

simple discharge circuit for an external

capacitor are built in.

The figure in the pin explanation and input/output equivalent circuit is reference value, it’s doesn’t guarantee the value.

25/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Operational Notes

1. Reverse Connection of Power Supply

Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when

connecting the power supply, such as mounting an external diode between the power supply and the IC’s power

supply pins.

2. Power Supply Lines

Design the PCB layout pattern to provide low impedance supply lines. Furthermore, connect a capacitor to ground at

all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic

capacitors.

3. Ground Voltage

Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.

4. Ground Wiring Pattern

When using both small-signal and large-current ground traces, the two ground traces should be routed separately but

connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal

ground caused by large currents. Also ensure that the ground traces of external components do not cause variations

on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.

5. Thermal Consideration

Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in

deterioration of the properties of the chip. In case of exceeding this absolute maximum rating, increase the board size

and copper area to prevent exceeding the Pd rating.

6. Recommended Operating Conditions

These conditions represent a range within which the expected characteristics of the IC can be approximately

obtained. The electrical characteristics are guaranteed under the conditions of each parameter.

7. Inrush Current

When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may

flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power

supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring,

and routing of connections.

8. Operation Under Strong Electromagnetic Field

Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.

9. Testing on Application Boards

When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may

subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply

should always be turned off completely before connecting or removing it from the test setup during the inspection

process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during

transport and storage.

10. Inter-pin Short and Mounting Errors

Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in

damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.

Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment)

and unintentional solder bridge deposited in between pins during assembly to name a few.

11. Unused Input Terminals

Because the input impedance of the terminal becomes 100kΩ when the signal input terminal makes a terminal open,

the plunge noise from outside sometimes becomes a problem.

About unused input pin, please connect to GND through capacitor, or please set that channel MUTE.

About unused output pin, it is no problem to set to open.

26/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Operational Notes – continued 1

12. Regarding the Input Pin of the IC

This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them

isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a

parasitic diode or transistor. For example (refer to figure below):

When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.

When GND > Pin B, the P-N junction operates as a parasitic transistor.

Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual

interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to

operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should

be avoided.

Figure 23. Example of monolithic IC structure

13. Ceramic Capacitor

When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with

temperature and the decrease in nominal capacitance due to DC bias and others.

14. About power ON/OFF

At power ON/OFF, a pop sound will be generated and, therefore, use MUTE on the set.

15. About EXT ATT(Select Address 33, 34, 35(hex)) switching

When switching EXT ATT, please set EXT OFF.

16. About Volume gain switching, EXT ON/OFF switching

In case of the boost of the volume when changing to the high gain which exceeds +12dB especially, the switching

pop noise sometimes becomes big. (For example, in case gain of the power amplifier is set to +26dB, and switching

time is set to 11.2msec)

In this case, countermeasures as below are recommended to decrease this pop noise.

・Switching gain by only 1dB/Step

・Increase switching time (In detail, please refer p9.)

27/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Operational Notes – continued 2

16. About output load characteristics

The usage of load for output are below (reference). Please use the load more than 10[kΩ](TYP).

Output terminal

Terminal

No.

Terminal

Name

Terminal

No.

Terminal

Name

Terminal

No.

Terminal

Name

Terminal

No.

Terminal

Name

18 OUTF1 16 OUTR1 14 OUTS1 10 DIFFOUT

17 OUTF2 15 OUTR2 13 OUTS2

Figure 24. Output load characteristic VCC=8.5V (Reference)

17. About constant set up of input coupling capacitor

In the signal input terminal, the constant setting of input coupling capacitor C(F) be sufficient input impedance

RIN(from 70 to 130kΩ) inside IC and please decide. The first HPF characteristic of RC is composed.

Figure 25. Input equivalent circuit

VCC=8.5V

THD+N=1%

BW=400 to 30kHz

0

0.5

1

1.5

2

2.5

100 1k 10k 100k

Load [Ω]

Output voltage [Vrms]

0dB

-3dB

G [ dB ]

f [ Hz ]

fc = 1/(2πCRIN)

C[F]

RIN[Ω]

28/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Ordering Information

B D 3 4 6 0 2 F S -ME 2

Part Number

Package

FS: SSOP-A24

Product Rank

M : for Automotive

Packaging and forming specification

E2 : Embossed tape and reel

(SSOP-A24)

Physical Dimension, Tape and Reel Information

Marking Diagrams

SSOP-A24(TOP VIEW)

BD34602FS

Part Number Marking

LOT Number

1PIN MARK

(Unit : mm)

SSOP-A24

24

0.1±0.1

12

0.8

−4°

+6°

0.17−0.05

+0.1

13

1.8±0.1

4°

0.38±0.1

1

10±0.2

0.5±0.2

1.2±0.15

7.8±0.3

5.4±0.2

(MAX 10.35 include BURR)

0.1

∗

Order quantity needs to be multiple of the minimum quantity.

Embossed carrier tapeTape

Quantity

Direction

of feed

The direction is the 1pin of product is at the upper left when you hold

reel on the left hand and you pull out the tape on the right hand

2000pcs

E2

()

Direction of feed

Reel 1pin

29/29

Datasheet

BD34602FS-M

TSZ02201-0C2C0E100310-1-2

www.rohm.com

TSZ22111・15・001

Revision History

Date Revision Changes

22.Oct.2015 001 New Release

Notice-PAA-E Rev.002

Notice

Precaution on using ROHM Products

1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1),

aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,

bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales

representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way

responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any

ROHM’s Products for Specific Applications.

(Note1) Medical Equipment Classification of the Specific Applications

JAPAN

USA

EU

CHINA

CLASSⅢ

CLASSⅡb

CLASSⅢ

CLASSⅣ

CLASSⅢ

2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor

products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate

safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which

a failure or malfunction of our Products may cause. The following are examples of safety measures:

[a] Installation of protection circuits or other protective devices to improve system safety

[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.

Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the

use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our

Products under any special or extraordinary environments or conditions (as exemplified below), your independent

verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents

[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust

[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,

H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves

[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items

[f] Sealing or coating our Products with resin or other coating materials

[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of

flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning

residue after soldering

[h] Use of the Products in places subject to dew condensation

4. The Products are not subject to radiation-proof design.

5. Please verify and confirm characteristics of the final or mounted products in using the Products.

6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,

confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power

exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect

product performance and reliability.

7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in

the range that does not exceed the maximum junction temperature.

8. Confirm that operation temperature is within the specified range described in the product specification.

9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in

this document.

Precaution for Mounting / Circuit board design

1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product

performance and reliability.

2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must

be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,

please consult with the ROHM representative in advance.

For details, please refer to ROHM Mounting specification

Notice-PAA-E Rev.002

Precautions Regarding Application Examples and External Circuits

1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the

characteristics of the Products and external components, including transient characteristics, as well as static

characteristics.

2. You agree that application notes, reference designs, and associated data and information contained in this document

are presented only as guidance for Products use. Therefore, in case you use such information, you are solely

responsible for it and you must exercise your own independent verification and judgment in the use of such information

contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses

incurred by you or third parties arising from the use of such information.

Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper

caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be

applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,

isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

Precaution for Storage / Transportation

1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:

[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2

[b] the temperature or humidity exceeds those recommended by ROHM

[c] the Products are exposed to direct sunshine or condensation

[d] the Products are exposed to high Electrostatic

2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period

may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is

exceeding the recommended storage time period.

3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads

may occur due to excessive stress applied when dropping of a carton.

4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of

which storage time is exceeding the recommended storage time period.

Precaution for Product Label

QR code printed on ROHM Products label is for ROHM’s internal use only.

Precaution for Disposition

When disposing Products please dispose them properly using an authorized industry waste company.

Precaution for Foreign Exchange and Foreign Trade act

Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign

trade act, please consult with ROHM in case of export.

Precaution Regarding Intellectual Property Rights

1. All information and data including but not limited to application example contained in this document is for reference

only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any

other rights of any third party regarding such information or data.

2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the

Products with other articles such as components, circuits, systems or external equipment (including software).

3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any

third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM

will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to

manufacture or sell products containing the Products, subject to the terms and conditions herein.

Other Precaution

1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.

2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written

consent of ROHM.

3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the

Products or this document for any military purposes, including but not limited to, the development of mass-destruction

weapons.

4. The proper names of companies or products described in this document are trademarks or registered trademarks of

ROHM, its affiliated companies or third parties.

DatasheetDatasheet

Notice – WE Rev.001

General Precaution

1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.

ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny

ROHM’s Products against warning, caution or note contained in this document.

2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior

notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s

representative.

3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all

information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or

liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or

concerning such information.

Datasheet

Part Number bd34602fs-m

Package SSOP-A24

Unit Quantity 2000

Minimum Package Quantity 2000

Packing Type Taping

Constitution Materials List inquiry

RoHS Yes

bd34602fs-m - Web Page

Distribution Inventory

Buy