36 071119
MARKING
C 685 22
16V
A CASE B CASE
C
G
J
A
4V
6.3V
10V
16V
20V D
E
V
25V
35V
Rated Voltage
Code
Capacitance
Code
Rated Voltage
(V)
Capacitance
(µF)
F93
Type
0J
Rated
Voltage
476
Capacitance
Code
pF code: 1st two digits
represent significant figures,
3rd digit represents multiplier
(number of zeros to follow)
M
Tolerance
K = ±10%
M = ±20%
A
Case
Size
See
table
above
HOW TO ORDER
ⵧ
Packaging
See Tape & Reel
Packaging Section
BE ⵧ
BE1 = 0.005xCV
Category Temperature Range: -55 to +125°C
Rated Temperature: +85°C
Capacitance Tolerance: ±20%, ±10% at 120Hz
Dissipation Factor: Refer to next page
ESR 100kHz: Refer to next page
Leakage Current: After 5 minutes application of rated voltage, leakage current at 20°C
is not more than 0.005 x CV (BE1 suffix).
Capacitance Change By Temperature +15% Max. at +125°C
+10% Max. at +85°C
-10% Max. at -55°C
TECHNICAL SPECIFICATIONS
F93-BE Series
Low Leakage Current, Standard Tantalum J-Lead
FEATURES
• Lower DCL 0.005 x CV
• Optional DCL sorting conditions
• Improved Failure Rate: 0.5%/1000 hours, 85°C, RV
• Low ESR options available
• 100% surge test for power supply circuit
APPLICATIONS
• IoT devices
• Wearable devices
• Industrial sensors
LEAD-FREE COMPATIBLE
COMPONENT
A, B CASE
A 476 47
10V
A CASE B CASE
J
A
6.3V
10V
Rated Voltage
Code
Capacitance
Code
Rated Voltage
(V)
Capacitance
(µF)
CASE DIMENSIONS: millimeters (inches)
Code
EIA Code EIA Metric
L W1 W2 H S
A 1206 3216-18 3.20 ± 0.20 1.60 ± 0.20 1.20 ± 0.10 1.60 ± 0.20 0.80 ± 0.20
(0.126 ± 0.008) (0.063 ± 0.008) (0.047 ± 0.004) (0.063 ± 0.008) (0.031 ± 0.008)
B 1210 3528-21 3.50 ± 0.20 2.80 ± 0.20 2.20 ± 0.10 1.90 ± 0.20 0.80 ± 0.20
(0.138 ± 0.008) (0.110 ± 0.008) (0.087 ± 0.004) (0.075 ± 0.008) (0.031 ± 0.008)
071119 37
F93-BE Series
Low Leakage Current, Standard Tantalum J-Lead
Capacitance Rated Voltage
μF Code 6.3V (0J) 10V (1A)
47 476 A/B A/B
68 686
100 107 A/B
Released ratings
Please contact to your local AVX sales office when these series are being designed
in your application.
#: "M" for ±20% tolerance, "K" for ± 10% tolerance.
*1 Low ESR options are available. Please contact to your local AVX sales office.
CAPACITANCE AND RATED VOLTAGE RANGE
(LETTER DENOTES CASE SIZE)
RATINGS & PART NUMBER REFERENCE
Item All Case (%)
Damp Heat ±10
Temperature cycles ±5
Resistance soldering heat ±5
Surge ±5
Endurance ±10
*2: ΔC/C Marked “*”
AVX Case Capacitance Rated DCL DF ESR *1 100kHz RMS Current (mA) *2
Part No. Size (μF) Voltage (μA) @ 120Hz @ 100kHz 25ºC 85ºC 125ºC ΔC/C MSL
(V) (%) (Ω) (%)
6.3 Volt
F930J476#AABE1 A 47 6.3 1.5 18 2.5 173 156 69 * 3
F930J476#BABE1 B 47 6.3 1.5 6 1.0 292 262 117 * 3
F930J107#AABE1 A 100 6.3 3.2 35 2.0 194 174 77 ±15 3
F930J107#BABE1 B 100 6.3 3.2 14 0.9 307 277 123 * 3
10 Volt
F931A476#AABE1 A 47 10 2.4 40 2.0 194 174 77 ±15 3
F931A476#BABE1 B 47 10 2.4 8 1.0 292 262 117 * 3
38 071119
TEST F93-BE series (Temperature range -55ºC to +125ºC)
Condition
At 40°C, 90 to 95% R.H., 500 hours (No voltage applied)
Capacitance Change ........... Refer to page 37 (*1)
Dissipation Factor ................ Initial specified value or less
Leakage Current .................. Initial specified value or less
-55°C / +125°C, 30 minutes each, 1000 cycles
Capacitance Change ........... Refer to page 37 (*1)
Dissipation Factor ................ Initial specified value or less
Leakage Current .................. Initial specified value or less
10 seconds reflow at 260°C, 5 seconds immersion at 260°C.
Capacitance Change ........... Refer to page 37 (*1)
Dissipation Factor ................ Initial specified value or less
Leakage Current .................. Initial specified value or less
After application of surge voltage in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF,
for 1000 successive test cycles at 85ºC, capacitors shall meet the characteristic requirements in the table above.
Capacitance Change ........... Refer to page 37 (*1)
Dissipation Factor ................ Initial specified value or less
Leakage Current .................. Initial specified value or less
After 2000 hours’ application of rated voltage in series with a 3Ω resistor at 85°C, or derated voltage in series
with a 3Ω resistor at 125°C, capacitors shall meet the characteristic requirements in the table above.
Capacitance Change ........... Refer to page 37 (*1)
Dissipation Factor ................ Initial specified value or less
Leakage Current .................. Initial specified value or less
After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body
which has no electrode and has been soldered beforehand on a substrate, there shall be found neither
exfoliation nor its sign at the terminal electrode.
Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at
both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is
applied with a specified jig at the center of substrate so that the substrate may bend by 1mm as
illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals.
0.5% per 1000 hours at 85°C, VR with 0.1Ω/V series impedance,
60% confidence level.
QUALIFICATION TABLE
F93-BE Series
Low Leakage Current, Standard Tantalum J-Lead
Damp Heat
(Steady State)
Temperature Cycles
Resistance to
Soldering Heat
Surge
Endurance
Shear Test
Terminal Strength
Failure Rate
071119 39
F93-BE Series
Low Leakage Current, Standard Tantalum J-Lead
AVX SOLID ELECTROLYTIC CAPACITOR ROADMAP
SERIES LINE UP: CONVENTIONAL SMD MnO2
