1ED020I12FTA Single IGBT Driver IC SP001054670 1 Overview Main Features * Single channel isolated IGBT Driver * For 600V/1200V IGBTs * 2 A rail-to-rail output * Vcesat-detection * Active Miller Clamp * Two level turn off Product Highlights * Coreless transformer isolated driver * Basic insulation according to DIN EN 60747-5-2 * Basic insulation recognized under UL 1577 * Integrated protection features * Suitable for operation at high ambient temperature * AEC Qualified Typical Application * Drive inverters for HEV and EV * Auxiliary inverters for HEV and EV * High Power DC/DC inverters Description The 1ED020I12FTA is a galvanic isolated single channel IGBT driver in PG-DSO-20 package that provides an output current capability of typically 2A. All logic pins are 5V CMOS compatible and could be directly connected to a microcontroller. The data transfer across galvanic isolation is realized by the integrated Coreless Transformer Technology. The 1ED020I12FTA provides several protection features like IGBT two level turn off, desaturation protection, active Miller clamping and active shut down. Type Package Marking 1ED020I12FTA PG-DSO-20 1ED020I12FTA Data Sheet www.infineon.com 1 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Table of Contents 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 3.1 3.2 Pin Configuration and Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pin Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4 4.1 4.2 4.3 4.3.1 4.3.2 4.3.3 4.3.4 4.4 4.5 4.6 4.7 4.8 4.8.1 4.8.2 4.8.3 4.9 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Protection Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Undervoltage Lockout (UVLO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . READY Status Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Active Shut-Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Non-Inverting and Inverting Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Driver Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Two-Level Turn-Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Minimal On Time / Off Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Protection Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Desaturation Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Active Miller Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Short Circuit Clamping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 10 10 11 11 11 11 11 12 12 12 13 13 13 13 13 13 5 5.1 5.2 5.3 5.4 5.4.1 5.4.2 5.4.3 5.4.4 5.4.5 5.4.6 5.4.7 5.4.8 5.4.9 Electrical Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recommended Operating Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Voltage Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Logic Input and Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gate Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Active Miller Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Short Circuit Clamping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dynamic Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Desaturation Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Active Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Two-level Turn-off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 14 15 15 16 16 17 18 18 19 19 20 21 21 6 6.1 6.2 6.3 Insulation Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Certified according to DIN EN 60747-5-2 (VDE 0884 Teil 2): 2003-01. Basic Insulation . . . . . . . . . . Recognized under UL 1577 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 22 22 22 7 Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 8 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 9 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Data Sheet 2 Rev. 3.0 2016-04-05 EiceDRIVERTM 1ED020I12FTA 9.1 9.2 Reference Layout for Thermal Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Printed Circuit Board Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Data Sheet 3 Rev. 3.0, 2016-04-05 1ED020I12FTA Single IGBT Driver IC List of Figures Figure 2-1 Figure 3-1 Figure 4-1 Figure 4-2 Figure 7-1 Figure 7-2 Figure 7-3 Figure 7-4 Figure 7-5 Figure 7-6 Figure 7-7 Figure 7-8 Figure 7-9 Figure 7-10 Figure 8-1 Figure 9-1 Data Sheet Block Diagram 1ED020I12FTA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pin Configuration PG-DSO-20 (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Application Example Bipolar Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Application Example Unipolar Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Propagation Delay, Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Principle Switching Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Typical Switching Behavior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 DESAT Switch-OFF Behavior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Short Switch ON Pulses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Short Switch OFF Pulses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Short Switch OFF Pulses, Ringing Surpression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 VCC2 Ramp Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 VCC2 Ramp Down and VCC2 Drop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Typical TTLSET Time over CTLSET Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 PG-DSO-20 (Plastic (Green) Dual Small Outline Package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Reference Layout for Thermal Data (Copper thickness 102 m) . . . . . . . . . . . . . . . . . . . . . . . . . . 29 4 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC List of Tables Table 3-1 Table 5-1 Table 5-2 Table 5-3 Table 5-4 Table 5-5 Table 5-6 Table 5-7 Table 5-8 Table 5-9 Table 5-10 Table 5-11 Table 5-12 Table 6-1 Table 6-2 Data Sheet Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Operating Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Recommended Operating Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Voltage Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Logic Input and Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Gate Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Active Miller Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Short Circuit Clamping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Dynamic Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Desaturation Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Active Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Two-level Turn-off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Certified according to DIN EN 60747-5-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Recognized under UL 1577 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Block Diagram 2 Block Diagram VCC1 18 UVLO UVLO & 6 VCC2 8 CLAMP 7 OUT 5 TLSET 3 DESAT 4 GND2 K4 2V IN+ 13 delay TX delay & RX 1 VCC1 VCC2 20MHz IN- 14 VEE2 & OSC LOGIC VCC1 RDY 15 & /RDY 1 DECODER RX TX VCC2 500A ENCODER VCC1 7V 1 K3 S FLT2 Q Q R VCC1 S 9V R 150 1 /RST 17 delay 1 RST VEE2 11 12 GND1 GND1 Figure 2-1 Data Sheet 1 19 20 1ED020I12FTA GND1 GND1 1 2 VEE2 VEE2 9 250 FLT VCC2 & 500A & RDY2 FLTNL /FLT 16 VEE2 250 10 VEE2 VEE2 Block Diagram 1ED020I12FTA 6 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Pin Configuration and Functionality 3 Pin Configuration and Functionality 3.1 Pin Configuration Table 3-1 Pin Configuration Pin No. Name Function 1 VEE2 Negative power supply output side 2 VEE2 Negative power supply output side 3 DESAT Desaturation protection 4 GND2 Signal ground output side 5 TLSET Two level set 6 VCC2 Positive power supply output side 7 OUT Driver output 8 CLAMP Miller clamping 9 VEE2 Negative power supply output side 10 VEE2 Negative power supply output side 11 GND1 Ground input side 12 GND1 Ground input side 13 IN+ Non inverted driver input 14 IN- Inverted driver input 15 RDY Ready output 16 FLT Fault output, low active 17 RST Reset input, low active 18 VCC1 Positive power supply input side 19 GND1 Ground input side 20 GND1 Ground input side Data Sheet 7 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Pin Configuration and Functionality 1 VEE2 GND1 20 2 VEE2 GND1 19 3 DESAT VCC1 18 4 GND2 /RST 17 5 TLSET /FLT 16 6 VCC2 RDY 15 7 OUT IN- 14 8 CLAMP IN+ 13 9 VEE2 GND1 12 10 VEE2 GND1 11 Figure 3-1 Pin Configuration PG-DSO-20 (top view) 3.2 Pin Functionality GND1 Ground connection of the input side. IN+ Non Inverting Driver Input IN+ control signal for the driver output if IN- is set to low. (The IGBT is on if IN+ = high and IN- = low) A minimum pulse width is defined to make the IC robust against glitches at IN+. An internal Pull-Down-Resistor ensures IGBT Off-State. IN- Inverting Driver Input IN- control signal for driver output if IN+ is set to high. (IGBT is on if IN- = low and IN+ = high) A minimum pulse width is defined to make the IC robust against glitches at IN-. An internal Pull-Up-Resistor ensures IGBT Off-State. /RST Reset Input Function 1: Enable/shutdown of the input chip. (The IGBT is off if /RST = low). A minimum pulse width is defined to make the IC robust against glitches at /RST. Function 2: Resets the DESAT-FAULT-state of the chip if /RST is low for a time TRST. An internal Pull-Up-Resistor is used to ensure /FLT status output. /FLT Fault Output Open-drain output to report a desaturation error of the IGBT (FLT is low if desaturation occurs) RDY Ready Status Open-drain output to report the correct operation of the device (RDY = high if both chips are above the UVLO level and the internal chip transmission is faultless). Data Sheet 8 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Pin Configuration and Functionality VCC1 5 V power supply of the input chip VEE2 Negative power supply pins of the output chip. If no negative supply voltage is available, all VEE2 pins have to be connected to GND2. DESAT Desaturation Detection Input Monitoring of the IGBT saturation voltage (VCE) to detect desaturation caused by short circuits. If OUT is high, VCE is above a defined value and a certain blanking time has expired, the desaturation protection is activated and the IGBT is switched off. The blanking time is adjustable by an external capacitor. CLAMP Miller Clamping Ties the gate voltage to ground after the IGBT has been switched off at a defined voltage to avoid a parasitic switch-on of the IGBT.During turn-off, the gate voltage is monitored and the clamp output is activated when the gate voltage goes below 2 V below VEE2. GND2 Reference Ground Reference ground of the output chip. OUT Driver Output Output pin to drive an IGBT. The voltage is switched between VEE2 and VCC2. In normal operating mode Vout is controlled by IN+, IN- and /RST. During error mode (UVLO, internal error or DESAT) Vout is set to VEE2 independent of the input control signals. VCC2 Positive power supply pin of the output side. TLSET Two Level Turn Off Adjust Circuitry at TLSET adjust the two level turn off time with an external capacitor to GND2 and the two level voltage with an external Zener diode to GND2, for wave forms please see Figure 7-4. Data Sheet 9 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Functional Description 4 Functional Description 4.1 Introduction The 1ED020I12FTA is an advanced IGBT gate driver for motor drives typical greater 10 kW. Control and protection functions are included to make possible the design of high reliability systems. The device consists of two galvanic separated parts. The input chip can be directly connected to a standard 5 V DSP or microcontroller with CMOS in/output and the output chip is connected to the high voltage side. An effective active Miller clamp function avoids the need of negative gate driving in some applications and allows the use of a simple bootstrap supply for the high side driver. A rail-to-rail driver output enables the user to provide easy clamping of the IGBTs gate voltage during short circuit of the IGBT. So an increase of short circuit current due to the feedback via the Miller capacitance can be avoided. Further, a rail-to-rail output reduces power dissipation. The device also includes an IGBT desaturation protection with a FAULT status output. A two-level turn-off feature with adjustable delay protects against excessive overvoltage at turn-off in case of overcurrent or short circuit condition. The same delay is applied at turn-on to prevent pulse width distortion. A READY status output reports if the device is supplied and operates correctly. 10R 10k 10k +5V SGND VCC1 +15V VCC2 100n 1 1k DESAT GND1 CLAMP IN+ IN+ RDY FLT /RST 10V 47p 220p GND2 /FLT RST 10R TLSET IN- RDY OUT 1 VEE2 -8V 1ED020I12FTA Figure 4-1 Application Example Bipolar Supply 4.2 Supply The driver 1ED020I12FTA is designed to support two different supply configurations, bipolar supply and unipolar supply. In bipolar supply the driver is typically supplied with a positive voltage of 15V at VCC2 and a negative voltage of -8V at VEE2, refer to Figure 4-1. Negative supply prevents a dynamic turn on due to the additional charge which is generated from IGBT input capacitance times negative supply voltage. If an appropriate negative supply voltage is used, connecting CLAMPxx to IGBT gate is redundant and therefore typically not necessary. For unipolar supply configuration the driver is typically supplied with a positive voltage of 15V at VCC2. Erratically dynamic turn on of the IGBT could be prevented with active Miller clamp function, so CLAMP output is directly connected to IGBT gate, refer to Figure 4-2. Data Sheet 10 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Functional Description 10R 10k 10k +5V VCC1 1 100n SGND +15V VCC2 1k DESAT GND1 CLAMP IN+ IN+ TLSET IN- RDY RDY FLT 10R OUT 10V 47p 220p GND2 /FLT RST /RST VEE2 1ED020I12FTA Figure 4-2 Application Example Unipolar Supply 4.3 Internal Protection Features 4.3.1 Undervoltage Lockout (UVLO) To ensure correct switching of IGBTs the device is equipped with an undervoltage lockout for both chips, refer to Figure 7-8 and Figure 7-9. If the power supply voltage VVCC1 of the input chip drops below VUVLOL1 a turn-off signal is sent to the output chip before power-down. The IGBT is switched off and the signals at IN+ and IN- are ignored as long as VVCC1 reaches the power-up voltage VUVLOH1. If the power supply voltage VVCC2 of the output chip goes down below VUVLOL2 the IGBT is switched off and signals from the input chip are ignored as long as VVCC2 reaches the power-up voltage VUVLOH2. VEE2 is not monitored, otherwise negative supply voltage range from 0 V to -12 V would not be possible. 4.3.2 READY Status Output The READY output at pin /RDY shows the status of three internal protection features. * * * UVLO of the input chip UVLO of the output chip after a short delay Internal signal transmission after a short delay It is not necessary to reset the READY signal since its state only depends on the status of the former mentioned protection signals. 4.3.3 Watchdog Timer During normal operation the internal signal transmission is monitored by a watchdog timer. If the transmission fails for a given time, the IGBT is switched off and the READY output reports an internal error. 4.3.4 Active Shut-Down The Active Shut-Down feature ensures a safe IGBT off-state if the output chip is not connected to the power supply, IGBT gate is clamped at OUT to VEE2. Data Sheet 11 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Functional Description 4.4 Non-Inverting and Inverting Inputs There are two possible input modes to control the IGBT. At non-inverting mode IN+ controls the driver output while IN- is set to low. At inverting mode IN- controls the driver output while IN+ is set to high, refer to Figure 7-2. A minimum input pulse width is defined to filter occasional glitches. 4.5 Driver Output The output driver section uses only MOSFETs to provide a rail-to-rail output. This feature permits that tight control of gate voltage during on-state and short circuit can be maintained as long as the drivers supply is stable. Due to the low internal voltage drop, switching behaviour of the IGBT is predominantly governed by the gate resistor. Furthermore, it reduces the power to be dissipated by the driver. 4.6 Two-Level Turn-Off The Two-Level Turn-OFF introduces a second turn off voltage level at the driver output in between ON- and OFF-level, refer to Figure 7-3. This additional level ensures lower VCE overshoots at turn off by reducing gate emitter voltage of the IGBT at short circuits or over current events. The VGE level is adjusting the current of the IGBT at the end two level turn off interval, the required timing is depending on stray inductance and over current at beginning of two level turn off interval. Reference voltage level and hold up time could be adjusted at TLSET pin. The reference voltage is set by the required Zener diode connected between pin TLSET and GND2. The holdup time is set by the capacitor connected to the same pin TLSET and GND2. The hold time can be adjusted during switch on using the whole capacitance connected at pin TLSET including capacitor, parasitic wiring capacitance and junction capacitance of Zener diode. When a switch on signal is given the IC starts to discharge CTLSET. Discharging CTLSET is stopped after 500 ns. Then Ctlset is charged with an internal charge current ITLSET. When the voltage of the capacitor CTLSET exceeds 7 V a second current source starts charging CTLSET up to VZDIODE. At the end of this discharge-charge cycle the gate driver is switched on. The time between IN initiated switch-on signal (minus an internal propagation delay of approximately 200 ns) and switch-on of the gate drive is sampled and stored digitally. It represents the two level turn off set time TTLSET during switch-off. Due to digitalization the tpdon time can vary in time steps of 50 ns. If switch off is initiated from IN+, IN- or /RST signal, the gate driver is switched off immediately after internal propagation delay of approximately 200 ns and VOUT begins to decrease to the second gate voltage level. For switch off initiated by DESAT, the gate driver switch off is delayed by desaturation sense to OUT delay, afterwards VOUT begins to decrease to the second gate voltage level. For reaching second gate voltage level the output voltage VOUT is sensed and compared with the Zener voltage VZDIODE. When VOUT falls below the reference voltage VZDIODE of the Zener diode the switch off process is interrupted and VOUT is adjusted to VZDIODE. OUT is switched to VEE2 after the holdup time has passed. The Two-Level Turn-OFF function cannot be disabled. Data Sheet 12 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Functional Description 4.7 Minimal On Time / Off Time The 1ED020I12FTA driver requires minimal on and off time for proper operation in the application. Minimal on time must be greater than the adjustable two level plateau time TTLSET, shorter on times will be suppressed by generating of the plateau time refer to Figure 7-5. Due to the short on time, the voltage at TLSET pin does not reach the comparator threshold; therefore the driver does not turn on. A similar principle takes place for off time. Minimal off time must be greater than TTLSET; shorter off times will be suppressed, which means OUT stays on refer to Figure 7-6. A two level turn off plateau cannot be shortened by the driver. If the driver has entered the turn off sequence it cannot switch off due to the fact, that the driver has already entered the shut off mode. But if the driver input signal is turned on again, it will leave the lower level after TTLSET time by switching OUT to high, refer to Figure 7-7. 4.8 External Protection Features 4.8.1 Desaturation Protection A desaturation protection ensures the protection of the IGBT at short circuit. When the DESAT voltage goes up and reaches 9 V, the output is driven low, refer to Figure 7-4. Further, the FAULT output is activated. A programmable blanking time is used to allow enough time for IGBT saturation. Blanking time is provided by a highly precise internal current source and an external capacitor. 4.8.2 Active Miller Clamp In a half bridge configuration the switched off IGBT tends to dynamically turn on during turn on phase of the opposite IGBT. A Miller clamp allows sinking the Miller current across a low impedance path in this high dV/dt situation. Therefore in many applications, the use of a negative supply voltage can be avoided. During turn-off, the gate voltage is monitored and the clamp output is activated when the gate voltage goes below typical 2 V (related to VEE2). The clamp is designed for a Miller current up to 2 A. 4.8.3 Short Circuit Clamping During short circuit the IGBTs gate voltage tends to rise because of the feedback via the Miller capacitance. An additional protection circuit connected to OUT and CLAMP limits this voltage to a value slightly higher than the supply voltage. A current of maximum 500 mA for 10 s may be fed back to the supply through one of this paths. If higher currents are expected or a tighter clamping is desired external Schottky diodes may be added. 4.9 RESET The reset input has two functions. Firstly, /RST is in charge of setting back the FAULT output. If /RST is low longer than a given time, /FLT will be cleared at the rising edge of /RST, refer to Figure 7-4; otherwise, it will remain unchanged. Moreover, it works as enable/shutdown of the input logic, refer to Figure 7-2. Data Sheet 13 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Electrical Parameters 5 Electrical Parameters 5.1 Absolute Maximum Ratings Note: Absolute maximum ratings are defined as ratings, which when being exceeded may lead to destruction of the integrated circuit. Unless otherwise noted all parameters refer to GND1. Table 5-1 Absolute Maximum Ratings Parameter Symbol Values Min. Max. Unit Note Positive power supply output side VVCC2 -0.3 20 V 1) Negative power supply output side VVEE2 -12 0.3 V 1) Maximum power supply voltage output side (VVCC2 - VVEE2) Vmax2 - 28 V - Gate driver output VOUT VVEE2-0.3 VVCC2+0.3 V - Gate driver high output maximum current IOUT - 2.4 A t = 2 s Gate & Clamp driver low output maximum current IOUT - 2.4 A t = 2 s Maximum short circuit clamping time tCLP - 10 s ICLAMP/OUT = 500 mA Positive power supply input side VVCC1 -0.3 6.5 V - Logic input voltages (IN+,IN-,RST) VLogicIN -0.3 6.5 V - Opendrain Logic output voltage (FLT) VFLT# -0.3 6.5 V - Opendrain Logic output voltage (RDY) VRDY -0.3 6.5 V - Opendrain Logic output current (FLT) IFLT# - 10 mA - Opendrain Logic output current (RDY) IRDY - 10 mA - Pin DESAT voltage VDESAT -0.3 VVCC2 +0.3 V 1) Pin CLAMP voltage VCLAMP -0.3 VVCC2 +0.32) V 3) Junction temperature TJ -40 150 C - Storage temperature TS -55 150 C - Power dissipation, per input part PD, IN - 100 mW 4) @TA = 25C Power dissipation, per output part PD, OUT - 700 mW 4) @TA = 25C K/W 4) @TA = 25C @TA = 25C Thermal resistance (Input part) RTHJA,IN - 139 Thermal resistance (Output chip active) RTHJA,OUT - 117 K/W 4) ESD Capability VESD - 1.5 kV Human Body Model5) 1) With respect to GND2. 2) May be exceeded during short circuit clamping. Data Sheet 14 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Electrical Parameters 3) With respect to VEE2. 4) Output IC power dissipation is derated linearly at 8.5 mW/C above 68C. Input IC power dissipation does not require derating. See Figure 9-1 for reference layouts for these thermal data. Thermal performance may change significantly with layout and heat dissipation of components in close proximity. 5) According to EIA/JESD22-A114-B (discharging a 100 pF capacitor through a 1.5 k series resistor). 5.2 Operating Parameters Note: Within the operating range the IC operates as described in the functional description. Unless otherwise noted all parameters refer to GND1. Table 5-2 Operating Parameters Parameter Symbol Values Min. Max. Unit Note Positive power supply output side VVCC2 13 20 V 1) Negative power supply output side VVEE2 -12 0 V 1) Maximum power supply voltage output side (VVCC2 - VVEE2) Vmax2 - 28 V - Positive power supply input side VVCC1 4.5 5.5 V - Logic input voltages (IN+,IN-,RST) VLogicIN -0.3 5.5 V - Pin CLAMP voltage VCLAMP VVEE2-0.3 VVCC22) V - Pin DESAT voltage VDESAT -0.3 VVCC2 V 1) Pin TLSET voltage VTLSET -0.3 VVCC2 V 1) TA -40 125 C - 50 kV/s @ 500 V Ambient temperature 3) Common mode transient immunity |DVISO/dt| - 1) With respect to GND2. 2) May be exceeded during short circuit clamping. 3) The parameter is not subject to production test - verified by design/characterization 5.3 Recommended Operating Parameters Note: Unless otherwise noted all parameters refer to GND1. Table 5-3 Recommended Operating Parameters Parameter Symbol Value Unit Note Positive power supply output side VVCC2 15 V 1) Negative power supply output side VVEE2 -8 V 1) Positive power supply input side VVCC1 5 V - 1) With respect to GND2. Data Sheet 15 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Electrical Parameters 5.4 Electrical Characteristics Note: The electrical characteristics include the spread of values in supply voltages, load and junction temperatures given below. Typical values represent the median values at TA = 25C. Unless otherwise noted all voltages are given with respect to their respective GND (GND1 for pins 11 to 20, GND2 for pins 1 to 10). 5.4.1 Voltage Supply Table 5-4 Voltage Supply Parameter Symbol Values Unit Note Min. Typ. Max. VUVLOH1 - 4.1 4.3 V - VUVLOL1 3.5 3.8 - V - VHYS1 0.15 - - V - - 12.0 12.6 V - 10.4 11.0 - V - UVLO Hysteresis Output Chip VHYS2 (VUVLOH1 - VUVLOL1) 0.7 0.9 - V - Quiescent Current Input Chip IQ1 - 7 9 mA VVCC1 =5 V IN+ = High, IN- = Low =>OUT = High, RDY = High, /FLT = High Quiescent Current Output Chip - 4.5 6 mA VVCC2 =15 V VVEE2 =-8 V IN+ = High, IN- = Low =>OUT = High, RDY = High, /FLT = High UVLO Threshold Input Chip UVLO Hysteresis Input Chip (VUVLOH1 - VUVLOL1) UVLO Threshold Output Chip VUVLOH2 VUVLOL2 Data Sheet IQ2 16 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Electrical Parameters 5.4.2 Logic Input and Output Table 5-5 Logic Input and Output Parameter Symbol Values Unit Note Min. Typ. Max. IN+,IN-, RST Low Input Voltage VIN+L, VIN-L, VRSTL# - - 1.5 V - IN+,IN-, RST High Input Voltage VIN+H, VIN-H, VRSTH# 3.5 - - V - IN-, RST Input Current IIN-, IRST# - 100 400 A VIN- = GND1 VRST# = GND1 IN+ Input Current IIN+, - 100 400 A VIN+ = VCC1 RDY,FLT Pull Up Current IPRDY, IPFLT# - 100 400 A VRDY = GND1 VFLT# = GND1 Input Pulse Suppression IN+, IN- TMININ+, TMININ- 30 40 - ns - Input Pulse Suppression RST for ENABLE/SHUTDOWN TMINRST 30 40 - ns - Pulse Width RST for Reseting FLT TRST 800 - - ns - FLT Low Voltage VFLTL - - 300 mV ISINK(FLT#) = 5 mA RDY Low Voltage VRDYL - - 300 mV ISINK(RDY) = 5 mA Data Sheet 17 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Electrical Parameters 5.4.3 Gate Driver Table 5-6 Gate Driver Parameter Symbol Values Unit Note Min. Typ. Max. VOUTH1 VVCC2-1.2 VVCC2-0.8 - V IOUTH = -20 mA VOUTH2 VVCC2-2.5 VVCC2-2.0 - V IOUTH = -200 mA VOUTH3 VVCC2-9 VVCC2-5 - V IOUTH = -1 A VOUTH4 - VVCC2-10 - V IOUTH = -2 A High Level Output Peak Current IOUTH -1.5 -2.0 - A IN+ = High, IN- = Low; OUT = High Low Level Output Voltage VOUTL1 - VVEE2+0.04 VVEE2+0.09 V IOUTL = 20 mA VOUTL2 - VVEE2+0.3 VVEE2+0.85 V IOUTL = 200 mA VOUTL3 - VVEE2+2.1 VVEE2+5.0 V IOUTL = 1 A VOUTL4 - VVEE2+7 - V IOUTL = 2 A 1.5 2.0 - A IN+ = Low, IN- = Low; OUT = Low, VVCC2 =15 V, VVEE2 =-8 V Unit Note High Level Output Voltage Low Level Output Peak IOUTL Current 5.4.4 Active Miller Clamp Table 5-7 Active Miller Clamp Parameter Symbol Values Min. Typ. Max. VCLAMPL1 - VVEE2+0.03 VVEE2 +0.08 V IOUTL = 20 mA VCLAMPL2 - VVEE2+0.3 VVEE2 +0.8 V IOUTL = 200 mA VCLAMPL3 - VVEE2+1.9 VVEE2 +4.8 V Low Level Clamp Current ICLAMPL 2 - - A IOUTL = 1 A 1) Clamp Threshold Voltage VCLAMP 1.6 2.1 2.4 V Related to VEE2 Low Level Clamp Voltage 1) The parameter is not subject to production test - verified by design/characterization Data Sheet 18 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Electrical Parameters 5.4.5 Short Circuit Clamping Table 5-8 Short Circuit Clamping Parameter Symbol Values Min. Typ. Max. Unit Note Clamping voltage (OUT) (VOUT-VVCC2) VCLPout - 0.8 1.3 V IN+=High, IN- = Low, OUT = High IOUT = 500 mA (pulse test, tCLPmax = 10 s) Clamping voltage (CLAMP) (VVCLAMP-VVCC2) VCLPclamp - 1.3 - V IN+ = High, IN- = Low, OUT = High ICLAMP = 500 mA (pulse test, tCLPmax = 10 s) Clamping voltage (CLAMP) VCLPclamp - 0.7 1.1 V IN+ = High, IN- = Low, OUT = High ICLAMP = 20 mA 5.4.6 Dynamic Characteristics Dynamic characteristics are measured with VVCC1 = 5 V, VVCC2 = 15 V and VVEE2 = -8 V. Table 5-9 Dynamic Characteristics Parameter Symbol Values Min. Typ. Max. Unit Note IN+, IN- Input to output propagation delay ON and OFF TPDON 1.5 1.75 2.0 s CTLSET = 0 pF, CLOAD = 100 pF, TA = 25C N+, IN- Input to output propagation delay distortion (TPDOFF-TPDON) TPDISTO -50 0 50 ns CTLSET = 0 pF, CLOAD = 100 pF, TA = 25C N+, IN- Input to output propagation delay ON and OFF TPDONt 1.5 1.9 2.3 s CTLSET = 0 pF, CLOAD = 100 pF, TA = 125C N+, IN- Input to output propagation delay distortion (TPDOFF-TPDON) TPDISTOt -20 45 70 ns CTLSET = 0 pF, CLOAD = 100 pF, TA = 125C IN+, IN- Input to output propagation delay ON and OFF TPDONt 1.45 1.75 2.05 s CTLSET = 0 pF, CLOAD = 100 pF, TA = -40C IN+ Input to output propagation delay distortion (TPDOFF-TPDON) TPDISTOt -60 -5 50 ns CTLSET = 0 pF, CLOAD = 100 pF, TA = -40C Data Sheet 19 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Electrical Parameters Table 5-9 Dynamic Characteristics (cont'd) Parameter Symbol Rise Time TRISE Fall Time 5.4.7 TFALL Values Unit Note Min. Typ. Max. 10 30 60 ns CLOAD = 1 nF, VL 10%, VH 90% 150 400 800 ns CLOAD = 34 nF VL 10%, VH 90% 10 20 40 ns CLOAD = 1 nF VL 10%, VH 90% 100 250 500 ns CLOAD = 34 nF VL 10%, VH 90% Unit Note Desaturation Protection Table 5-10 Desaturation Protection Parameter Symbol Values Min. Typ. Max. Blanking Capacitor Charge IDESATC Current 450 500 550 A VVCC2 =15 V, VVEE2 =-8 V VDESAT = 2 V Blanking Capacitor Discharge Current IDESATD 11 15 - mA VVCC2 =15 V, VVEE2 =-8 V VDESAT =6 V Desaturation Reference Level VDESAT 8.5 9 9.5 V VVCC2 =15 V Desaturation Sense to OUT TDESATOUT TLTO - 250 320 ns VOUT =90% CLOAD = 1 nF Desaturation Sense to FLT Low Delay TDESATFLT - - 2.25 s VFLT #=10%; IFLT #=5 mA Desaturation Low Voltage VDESATL 40 70 110 mV IN+=Low, IN-=Low, OUT=Low Data Sheet 20 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Electrical Parameters 5.4.8 Active Shut Down Table 5-11 Active Shut Down Parameter Symbol Active Shut Down Voltage VACTSD1) Values Min. Typ. Max. - - 2.0 Unit Note V IOUT = -200 mA, VCC2 open Unit Note 1) With reference to VEE2 5.4.9 Two-level Turn-off Table 5-12 Two-level Turn-off Parameter Symbol Values Min. Typ. Max. External reference voltage range (Zener-Diode) VZDIODE 7.5 - VCC2-0.5 V - Reference Voltage for setting two-level delay time VTLSET 6.6 7 7.3 V - Current for setting two-level ITLSET delay time and external reference voltage (Zener-Diode) 420 500 550 A VTLSET = 10 V External Capacitance Range 0 - 220 pF - Data Sheet CTLSET 21 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Insulation Characteristics 6 Insulation Characteristics Insulation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. Surface mount classification is class A in accordance with CECCOO802. This coupler is suitable for "basic insulation" only within the safety ratings. Compliance with the safety ratings shall be ensured by means of suitable protective circuits. 6.1 Certified according to DIN EN 60747-5-2 (VDE 0884 Teil 2): 2003-01. Basic Insulation Table 6-1 Certified according to DIN EN 60747-5-2 Description Symbol Characteristic Unit Installation classification per EN 60664-1, Table 1 for rated mains voltage 150 VRMS for rated mains voltage 300 VRMS for rated mains voltage 600 VRMS I-IV I-III I-II Climatic Classification 40/125/21 - Pollution Degree (EN 60664-1) 2 - - Minimum External Clearance CLR 8 mm Minimum External Creepage CPG 8 mm Minimum Comparative Tracking Index CTI 175 - Maximum Repetitive Insulation Voltage VIORM 1420 VPEAK Highest Allowable Overvoltage VIOTM 6000 VPEAK Maximum Surge Insulation Voltage VIOSM 6000 V Description Symbol Characteristic Unit Insulation Withstand Voltage / 1 min VISO 3750 Vrms Insulation Test Voltage / 1 s VISO 4500 Vrms 6.2 Recognized under UL 1577 Table 6-2 Recognized under UL 1577 6.3 Reliability For Qualification Report please contact your local Infineon Technologies office. Data Sheet 22 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Timing Diagrams 7 Timing Diagrams All diagrams related to the Two-level switch-off feature 50% IN+ 90% 50% OUT 10% TPDON Figure 7-1 TRISE TPDOFF TFALL Propagation Delay, Rise and Fall Time IN+ IN/RST OUT Figure 7-2 Principle Switching Behavior IN+ V ZDIODE VTLSET , typ. 7V TLSET TPD TADJ1 V ZDIODE TTLSET TPD TTLFALL OUT TPDONADJ Figure 7-3 Data Sheet TTLSET Typical Switching Behavior 23 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Timing Diagrams IN+ TPDON OUT TTLSET TTLSET TDESATOUT TDESATOUT VDESAT typ. 9V DESAT /FLT TDESATFLT TDESATFLT /RST >TRSTmin Figure 7-4 DESAT Switch-OFF Behavior IN+ TLSET TPD TTLSET TTLSET OUT Figure 7-5 Data Sheet TTLSET TPDON TPD TPDON TPDOFF Short Switch ON Pulses 24 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Timing Diagrams IN+ TLSET TTLSET TTLSET TPD Figure 7-6 TPD TPDOFF OUT TTLSET TPDON TPDOFF TPDON TPDOFF Short Switch OFF Pulses IN+ TLSET TPD OUT TTLSET TPDON TTLSET TPDOFF TTLSET TPDOFF TTLSET TPD TPDOFF TPDON forced turn off after three consecutive on -cycles Figure 7-7 Data Sheet Short Switch OFF Pulses, Ringing Surpression 25 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Timing Diagrams VUVLOH2 VCC2 IN+ TPDON OUT TPDOFF I DESAT RDY Figure 7-8 VCC2 Ramp Up VCC2 VUVLOH2 VUVLOL2 TPDD TPDD IN+ TPDD TTLSET TLSET Vz OUT TPDON RDY /FLT Figure 7-9 Data Sheet VCC2 Ramp Down and VCC2 Drop 26 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Timing Diagrams 5 TTLSET [usec] 4 3 2 1 0 0 50 100 150 200 C TLSET [pF] Figure 7-10 Typical TTLSET Time over CTLSET Capacitance Data Sheet 27 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Package Outlines 8 Package Outlines Figure 8-1 PG-DSO-20 (Plastic (Green) Dual Small Outline Package) Data Sheet 28 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Application Notes 9 Application Notes 9.1 Reference Layout for Thermal Data The PCB layout shown in Figure 9-1 represents the reference layout used for the thermal characterisation. Pins 11, 12, 19 and 20 (GND1) and pins 1, 2, 9 and 10 (VEE2) require ground plane connections for achiving maximum power dissipation. The 1ED020I12FTA is conceived to dissipate most of the heat generated through this pins. Figure 9-1 Reference Layout for Thermal Data (Copper thickness 102 m) 9.2 Printed Circuit Board Guidelines Following factors should be taken into account for an optimum PCB layout. * * * * Sufficient spacing should be kept between high voltage isolated side and low voltage side circuits. The same minimum distance between two adjacent high-side isolated parts of the PCB should be maintained to increase the effective isolation and reduce parasitic coupling. In order to ensure low supply ripple and clean switching signals, bypass capacitor trace lengths should be kept as short as possible. Lowest trace length for VEE2 to GND2 decoupling could be achieved with capacitor closed to pins 2 and 4. Data Sheet 29 Rev. 3.0 2016-04-05 1ED020I12FTA Single IGBT Driver IC Revision History Page or Item Subjects (major changes since previous revision) Rev. 3.0, 2016-04-05 All Update latest template Page 8 removed Target Application Figure Page 14 Editorial changes, typos: - Symbol changed from Vmax2 to Vcc2 in Gate driver output - Pin CLAMP voltage unit changed from C to V - Desaturation protection filter time changed Page 6 Updated Block Diagram Page 14, Page 15, Page 16, Page 17, Page 18, Page 19, Page 20, Page 21 removed "Test Condition" from table header Data Sheet 30 Rev. 3.0 2016-04-05 Please read the Important Notice and Warnings at the end of this document Trademarks of Infineon Technologies AG HVICTM, IPMTM, PFCTM, AU-ConvertIRTM, AURIXTM, C166TM, CanPAKTM, CIPOSTM, CIPURSETM, CoolDPTM, CoolGaNTM, COOLiRTM, CoolMOSTM, CoolSETTM, CoolSiCTM, DAVETM, DI-POLTM, DirectFETTM, DrBladeTM, EasyPIMTM, EconoBRIDGETM, EconoDUALTM, EconoPACKTM, EconoPIMTM, EiceDRIVERTM, eupecTM, FCOSTM, GaNpowIRTM, HEXFETTM, HITFETTM, HybridPACKTM, iMOTIONTM, IRAMTM, ISOFACETM, IsoPACKTM, LEDrivIRTM, LITIXTM, MIPAQTM, ModSTACKTM, my-dTM, NovalithICTM, OPTIGATM, OptiMOSTM, ORIGATM, PowIRaudioTM, PowIRStageTM, PrimePACKTM, PrimeSTACKTM, PROFETTM, PRO-SILTM, RASICTM, REAL3TM, SmartLEWISTM, SOLID FLASHTM, SPOCTM, StrongIRFETTM, SupIRBuckTM, TEMPFETTM, TRENCHSTOPTM, TriCoreTM, UHVICTM, XHPTM, XMCTM. Trademarks updated November 2015 Other Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition 2016-04-05 Published by Infineon Technologies AG 81726 Munich, Germany (c) 2016 Infineon Technologies AG. All Rights Reserved. Do you have a question about any aspect of this document? Email: erratum@infineon.com IMPORTANT NOTICE The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics ("Beschaffenheitsgarantie"). With respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. In addition, any information given in this document is subject to customer's compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer's products and any use of the product of Infineon Technologies in customer's applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer's technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies' products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.