IEC inlet filters
FN 9244E
Excellent performance IEC inlet filter
with earth line choke
Approvalsn Rated currents up to 15A
n Superior attenuation performance
n Integrated earth line choke
n Optional medical versions (B type)
n Snap-in versions (S and S1 type)
n Hot inlet versions (HI type)
(CQC approval pending)
Typical applications
The FN 9244E IEC inlet filter combines an
IEC inlet and mains filter with superior
filter attenuation in a small form factor.
The FN 9244E high performance power
entry module offers additional EMI sup-
pression on the earth line. Choosing the
FN 9244E product line brings you the rapid
availability of a standard filter associated
with the necessary safety acceptances.
Standard IEC connector filters are a practi-
cal solution helping you to pass EMI system
approval in a short time. A wide selection
on amperage ratings, output connections,
mounting possibilities and filters for medi-
cal applications are designed to offer you
the desired solution. For types without
additional earth line choke please consult
the FN 9244 data sheet.
n Superior conducted attenuation
performance, based on chokes with high
saturation resistance and excellent thermal
behavior.
n Rear/front or snap-in mounting.
n Without earth line choke see FN 9244 data
sheet.
n Optional medical versions (B type)
according to IEC/EN 60601-1.
n Wide mounting flanges available.
n Custom-specific versions are available on
request.
n Electrical and electronic equipment
n Small to medium-sized machines and
household equipment
n Single-phase power supplies, switch-mode
power supplies
n Test and measurement equipment
n Medical devices (MDD)
n In-vitro diagnostic medical devices (IVDD)
n Rack mounting equipment
Features and benefits
Technical specifications
Maximum continuous operating voltage: 250VAC, 50/60Hz
Operating frequency: dc to 400Hz
Rated currents: 1 to 15A @ 50°C
Approvals by rated current: 1 to 10A (ENEC, CQC)
1 to 15A (UL, CSA)
High potential test voltage: P –> E 2000VAC for 2 sec (standard types)
P –> E 2500VAC for 2 sec (B types)
P –> N 1000VAC for 2 sec
Protection category: IP40 according to IEC 60529
Temperature range (operation and storage): -25°C to +85°C (25/85/21)
Design corresponding to: UL 1283, CSA 22.2 No. 8 1986, IEC/EN 60939
Flammability corresponding to: UL 94V-2 or better
MTBF @ 40°C/230V (Mil-HB-217F): 2,230,000 hours
Typical electrical schematic
N
E
P
Line
L2
Cx R 2xL1 2xCy
N‘
E‘
P‘
Load
> Components > FN 9244E
Filter selection table
FN 9244Ex-1-06 1 (1.2) 373 59.53 0.335 0.1 2.2 -06 46
FN 9244Ex-3-06 3 (3.5) 373 13.45 0.6 0.1 2.2 -06 46
FN 9244Ex-6-06 6 (7.2) 373 4.1 0.9 0.1 2.2 -06 46
FN 9244Ex-8-06 8 (10.6) 373 2.3 1.0 0.1 2.2 -06 46
FN 9244Ex-10-06 10 (11.6) 373 1.02 1.0 0.1 2.2 -06 46
FN 9244Ex-12-06 12 (12) 373 0.58 1.1 0.1 2.2 -06 46
FN 9244Ex-15-06 15 (15) 373 0.4 1.2 0.1 2.2 -06 46
FN 9244Ex-12-06HI 12 (12) 373 0.58 1.1 0.1 2.2 -06 46
FN 9244Ex-15-06HI 15 (15) 373 0.4 1.2 0.1 2.2 -06 46
FN 9244ExR-1-06 1 (1.2) 373 59.53 0.335 0.1 2.2 1000 -06 46
FN 9244ExR-3-06 3 (3.5) 373 13.45 0.6 0.1 2.2 1000 -06 46
FN 9244ExR-6-06 6 (7.2) 373 4.1 0.9 0.1 2.2 1000 -06 46
FN 9244ExR-8-06 8 (10.6) 373 2.3 1.0 0.1 2.2 1000 -06 46
FN 9244ExR-10-06 10 (11.6) 373 1.02 1.0 0.1 2.2 1000 -06 46
FN 9244ExR-12-06 12 (12) 373 0.58 1.1 0.1 2.2 1000 -06 46
FN 9244ExR-15-06 15 (15) 373 0.4 1.2 0.1 2.2 1000 -06 46
FN 9244ExR-12-06HI 12 (12) 373 0.58 1.1 0.1 2.2 1000 -06 46
FN 9244ExR-15-06HI 15 (15) 373 0.4 1.2 0.1 2.2 1000 -06 46
FN 9244ExB-1-06 1 (1.2) 2 59.53 0.335 0.1 1000 -06 46
FN 9244ExB-3-06 3 (3.5) 2 13.45 0.6 0.1 1000 -06 46
FN 9244ExB-6-06 6 (7.2) 2 4.1 0.9 0.1 1000 -06 46
FN 9244ExB-8-06 8 (10.6) 2 2.3 1.0 0.1 1000 -06 46
FN 9244ExB-10-06 10 (11.6) 2 1.02 1.0 0.1 1000 -06 46
FN 9244ExB-12-06 12 (12) 2 0.58 1.1 0.1 1000 -06 46
FN 9244ExB-15-06 15 (15) 2 0.4 1.2 0.1 1000 -06 46
FN 9244ExB-12-06HI 12 (12) 2 0.58 1.1 0.1 1000 -06 46
FN 9244ExB-15-06HI 15 (15) 2 0.4 1.2 0.1 1000 -06 46
* Maximum leakage under normal operating conditions. Note: if the neutral line is interrupted, worst case leakage could reach twice this level.
Filter Rated current Leakage current* Inductance Capacitance Resistance Output connections Weight
@ 50°C (25°C) @ 250VAC/50Hz L1 L2 Cx Cy R
[A] [µA] [mH] [mH] [µF] [nF] [kΩ] [g]
Product selector
FN 9244Exx-yy-..HI-zz
Snap-in range for S version only
Blank: Snap-in range 0.7 to 1.5mm
20: Snap-in range 1.5 to 2.2mm
Blank: Standard IEC inlet type C14
HI: Hot IEC inlet type C16 (12 and 15A types only)
06: Faston 6.3 x 0.8mm (spade/soldering)
1 to 15: Rated current
Blank: Standard version
R: Bleed resistor
B: Medical version (with bleed resistor and without Y2-capacitor)
Blank: Standard housing with mounting flanges
U: Housing with wider mounting flanges
S: Snap-in version, snapper on vertical side
S1: Snap-in version, snapper on horizontal side
For example: FN 9244E-15-06, FN 9244ES1B-10-06-20, FN 9244ER-12-06HI, FN 9244EUB-8-06
> Components > FN 9244E
Per CISPR 17; A = 50Ω/50Ω sym; B = 50Ω/50Ω asym; C = 0.1Ω/100Ω sym; D = 100Ω/0.1Ω sym
Typical filter attenuation
1 and 3A types 6 to 10A types 12 and 15A types
Mechanical data
FN 9244E FN 9244E-HI
FN 9244ES FN 9244ES1
AC
B
E
G
S
FDI
6.3 x 0.8
JA
B
E
GF D I
J
6.3 x 0.8
6.3 x 0.8
J
IDF
B
A
G
E
Panel cut out
Installation
T
HH
C
S
A
B
E
GFDI
J
6.3 x 0.8
FN 9244EU
A
C
B
E
G
S
FDI
6.3 x 0.8
J
H
C
PR
M
N
> Components > FN 9244E
Your local partner: To find your local partner within Schaffner’s global network, please go to www.schaffner.com August 2008
* For selecting the panel thickness, please refer to the filter selector table.
All dimensions in mm; 1 inch = 25.4mm
Tolerances according: ISO 2768-m / EN 22768-m
FN 9244E FN 9244EU FN 9244ES FN 9244ES1 FN 9244E-HI
Dimensions
A 48 51.85 29.9 29.9 48
B 22.5 25 22.4 22.4 22.5
C 40 ±0.2 40 ±0.2 40 ±0.2
D 46.8 46.8 46.8 46.8 46.8
E 27.8 27.8 27.8 27.8 27.8
F 5.5 5.5 5.5 5.5 5.5
G 20.1 20.1 20.1 20.1 20.1
H Ø3.3 Ø3.3 Ø3.3
I 14 14.1 14 14 14
J 13.3 13.3 13.3 13.3 13.3
M R ≤ 3 R ≤ 3 R ≤ 1.5 R ≤ 1.5 R ≤ 3
N 21.5 21.5 20.8 21.9 21.5
P 28.5 28.5 29.4 28.5 28.5
R M3 M3 M3
S 90° 90° 90°
T* 0.7 - 1.5 0.7 - 1.5
T* 1.5 - 2.2 1.5 - 2.2
Headquarters
Schaffner EMV AG
4542 Luterbach, Switzerland
T +41 32 681 66 26
F +41 32 681 66 41
sales@schaffner.com
www.schaffner.com
China
Schaffner EMC Ltd. Shanghai
T +86 21 6813 9855
cschina@schaffner.com
Finland
Schaffner Oy
T +358 19 357 271
finlandsales@schaffner.com
France
Schaffner EMC S.A.S.
T +33 1 34 34 30 60
francesales@schaffner.com
Germany
Schaffner EMV GmbH
T +49 721 56910
germanysales@schaffner.com
Schaffner Jacke GmbH
T +49 2951 6001 0
jacke-trafo@schaffner.com
Italy
Schaffner EMC S.r.l.
T +39 02 66 04 30 45
italysales@schaffner.com
Japan
Schaffner EMC K.K.
T +81 3 5456 0180
japansales@schaffner.com
Singapore
Schaffner EMC Pte Ltd.
T +65 6377 3283
singaporesales@schaffner.com
Sweden
Schaffner EMC AB
T +46 8 5792 1121
swedensales@schaffner.com
Switzerland
Schaffner EMV AG
T +41 32 681 66 26
sales@schaffner.ch
Taiwan
Schaffner EMV Ltd.
T +886 2 87525050
taiwansales@schaffner.com
Thailand
Schaffner EMC Co. Ltd.
T +66 53 58 11 04
thailandsales@schaffner.com
UK
Schaffner Ltd.
T +44 118 9770070
uksales@schaffner.com
USA
Schaffner EMC Inc.
T +1 732 225 9533
Toll free 1 800 367 5566
usasales@schaffner.com
To find your local partner within
Schaffner‘s global network, please go to
www.schaffner.com
August 2008
© 2008 Schaffner EMC.
Specifications subject to change without
notice. All trademarks recognized.
Schaffner is an ISO-registered company.
Its products are designed and manufac-
tured under the strict quality and environ-
mental requirements of the ISO 9001 and
ISO 14001 standards.
This document has been carefully
checked. However, Schaffner does not
assume any liability for errors or inac-
curacies.
