HM50-101KLF - WELWYN COMPONENTS

October, 2015 − Rev. 6 1Publication Order Number:

PCA9535E/D

PCA9535E, PCA9535EC

16-bit Low-Power I/O

Expander for I2C Bus with

Interrupt

The PCA9535E and PCA9535EC devices provide 16 bits of

General Purpose parallel Input / Output (GPIO) expansion through the

I2C−bus / SMBus.

The PCA9535E and PCA9535EC consist of two 8−bit

Configuration (Input or Output selection); Input, Output and Polarity

Inversion (active−HIGH or active−LOW operation) registers. At

power on, all I/Os default to inputs. Each I/O may be configured as

either input or output by writing to its corresponding I/O configuration

bit. The data for each Input or Output is kept in its corresponding Input

or Output register. The Polarity Inversion register may be used to

invert the polarity if the read register. All registers can be read by the

system master.

The PCA9535E, identical to the PCA9655E but with the internal

I/O pull−up resistors removed, has greatly reduced power

consumption when the I/Os are held LOW.

The PCA9535EC is identical to the PCA9535E but with

high−impedance open−drain outputs at all the I/O pins.

The PCA9535E and PCA9535EC provide an open−drain interrupt

output which is activated when any input state differs from its

corresponding input port register state. The interrupt output is used to

indicate to the system master that an input state has changed. The

power−on reset sets the registers to their default values and initializes

the device state machine.

Three hardware pins (AD0, AD1, AD2) are used to configure the

I2C−bus slave address of the device. The I2C−bus slave addresses of

the PCA9535E and PCA9535EC are the same as the PCA9655E. This

allows up to 64 of these devices in any combination to share the same

I2C−bus/SMBus.

Features

•VDD Operating Range: 1.65 V to 5.5 V

•SDA Sink Capability: 30 mA

•5.5 V Tolerant I/Os

•Polarity Inversion Register

•Active LOW Interrupt Output

•Low Standby Current

•Noise Filter on SCL/SDA Inputs

•No Glitch on Power−up

•Internal Power−on Reset

•64 Programmable Slave Addresses using Three

Address Pins

•16 I/O Pins which Default to 16 Inputs

•I2C SCL Clock Frequencies Supported:

Standard Mode: 100 kHz

Fast Mode: 400 kHz

Fast Mode +: 1 MHz

•ESD Performance: 3000 V Human Body Model, 400 V

Machine Model

•NLV Prefix for Automotive and Other Applications

Requiring Unique Site and Control Change

Requirements; AEC−Q100 Qualified and PPAP

Capable

•These are Pb−Free Devices

SOIC−24

DW SUFFIX

CASE 751E

See detailed ordering and shipping information in the package

dimensions section on page 17 of this data sheet.

ORDERING INFORMATION

MARKING

DIAGRAMS

www.onsemi.com

TSSOP−24

DT SUFFIX

CASE 948H

WQFN24

MT SUFFIX

CASE 485BG

PCA

9535E(C)

ALYWG

PCA95

35E(C)G

ALYW

PCA9535E(C)

AWLYYWWG

XXXX = Specific Device Code

A = Assembly Location

WL, L = Wafer Lot

YY, Y = Year

WW, W = Work Week

G or G= Pb−Free Package

(Note: Microdot may be in either location)

PCA9535E, PCA9535EC

www.onsemi.com

BLOCK DIAGRAM

Remark: All I/Os are set as inputs at reset.

Figure 1. Block Diagram

PCA9535E

POWER−ON

RESET

I2C−BUS/SMBus

CONTROL

INPUT

FILTER

SCL

SDA

VDD

INPUT/

OUTPUT

PORTS

IO0_0

VSS

8−bit

write pulse

read pulse

IO0_2

IO0_1

IO0_3

IO0_4

IO0_5

IO0_6

IO0_7

INPUT/

OUTPUT

PORTS

IO1_0

8−bit

write pulse

read pulse

IO1_2

IO1_1

IO1_3

IO1_4

IO1_5

IO1_6

IO1_7

INT

AD1

AD0

AD2

LP filter

VDD

PCA9535EC

1. PCA9535EC I/Os are open−drain only. The portion of the PCA9535E schematic marked inside the dotted line box is not in

PCA9535EC. Figure 2. Simplified Schematic of I/Os

At power−on reset, all registers return to default values.

VDD

I/O pin

output port

configuration

CK Q

data from

shift register

write

configuration

pulse

output port

write pulse

polarity inversion

data from

shift register

write polarity

pulse

input port

read pulse

input port

polarity

inversion

data from

shift register

VSS

to INT

(1)

PCA9535E, PCA9535EC

www.onsemi.com

PIN ASSIGNMENT

Figure 3. SOIC24 / TSSOP24 Figure 4. WQFN24

VINT DD

SDAAD1 SCLAD2 AD0IO0_0 IO1_7IO0_1 IO1_6IO0_2 IO1_5IO0_3 IO1_4IO0_4 IO1_3IO0_5 IO1_2IO0_6 IO1_1IO0_7

VSS IO1_0

PCA9535E

12 14

PCA9535EC

(The exposed thermal pad at the bottom

is not connected to internal circuitry)

Transparent top view

IO1_3

IO1_4

IO0_3

IO0_2

IO0_1

AD0IO0_0

IO0_6

IO0_7

VSS

IO1_0

IO1_1

IO1_2

AD2

AD1

INT

VDD

SDA

SCL

terminal 1

index area

6 13

5 14

4 15

3 16

2 17

1 18

PCA9535E

IO0_5

IO0_4

IO1_5

IO1_6

IO1_7

PCA9535EC

Table 1. PIN DESCRIPTIONS

Symbol

Description

SOIC24, TSSOP24 WQFN24

INT 1 22 Interrupt Output (active−LOW)

AD1 2 23 Address Input 1

AD2 3 24 Address Input 2

IO0_0 4 1 Port 0 I/O 0

IO0_1 5 2 Port 0 I/O 1

IO0_2 6 3 Port 0 I/O 2

IO0_3 7 4 Port 0 I/O 3

IO0_4 8 5 Port 0 I/O 4

IO0_5 9 6 Port 0 I/O 5

IO0_6 10 7 Port 0 I/O 6

IO0_7 11 8Port 0 I/O 7

VSS 12 9 Supply Ground

IO1_0 13 10 Port 1 I/O 0

IO1_1 14 11 Port 1 I/O 1

IO1_2 15 12 Port 1 I/O 2

IO1_3 16 13 Port 1 I/O 3

IO1_4 17 14 Port 1 I/O 4

IO1_5 18 15 Port 1 I/O 5

IO1_6 19 16 Port 1 I/O 6

IO1_7 20 17 Port 1 I/O 7

AD0 21 18 Address Input 0

SCL 22 19 Serial Clock Line

SDA 23 20 Serial Data Line

VDD 24 21 Supply Voltage

PCA9535E, PCA9535EC

www.onsemi.com

Table 2. MAXIMUM RATINGS

Symbol Parameter Value Unit

VDD DC Supply Voltage −0.5 to +7.0 V

VI/O Input / Output Pin Voltage −0.5 to +7.0 V

IIInput Current $20 mA

IOOutput Current $50 mA

IDD DC Supply Current $100 mA

IGND DC Ground Current $600 mA

PTOT Total Power Dissipation 600 mW

POUT Power Dissipation per Output 200 mW

TSTG Storage Temperature Range −65 to +150 °C

TLLead Temperature, 1 mm from Case for 10 Seconds 260 °C

TJJunction Temperature Under Bias 150 °C

qJA Thermal Resistance (Note 1) SOIC−24

TSSOP−24

WQFN24

°C/W

MSL Moisture Sensitivity Level 1

FRFlammability Rating Oxygen Index: 28 to 34 UL 94 V−0 @

0.125 in

VESD ESD Withstand Voltage Human Body Mode (Note 2)

Machine Model (Note 3)

Charged Device Model (Note 4)

> 3000

> 400

N/A

ILATCHUP Latchup Performance Above VDD and Below GND at 125°C (Note 5) $100 mA

Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device

functionality should not be assumed, damage may occur and reliability may be affected.

1. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 2 ounce copper trace no air flow .

2. Tested to EIA / JESD22−A114−A.

3. Tested to EIA / JESD22−A115−A.

4. Tested to JESD22−C101−A.

5. Tested to EIA / JESD78.

Table 3. RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Min Max Unit

VDD Positive DC Supply Voltage 1.65 5.5 V

VI/O Switch Input / Output Voltage 0 5.5 V

TAOperating Free−Air Temperature −55 +125 °C

Dt/DVInput Transition Rise or Fall Rate 0 5 ns/V

PCA9535E, PCA9535EC

www.onsemi.com

Table 4. DC ELECTRICAL CHARACTERISTICS VDD = 1.65 V to 5.5 V, unless otherwise specified.

Symbol Parameter Conditions

TA = −555C to +1255C

Unit

Min Typ Max

SUPPLIES

ISTB Standby Current (Note 6) Standby mode; no load;

VI = 0 V; fSCL = 0 Hz; I/O = inputs

VI = VDD; fSCL = 0 Hz; I/O = inputs 39

39 100

100

VPOR Power−On Reset Voltage (Note 7) 1.5 1.65 V

INPUT SCL; INPUT / OUTPUT SDA

VIH High−Level Input Voltage 0.7 x VDD V

VIL Low−Level Input Voltage 0.3 x VDD V

IOL Low−Level Output Current VOL = 0.4 V; VDD < 2.3 V

VOL = 0.4 V; VDD w 2.3 V 10

20 mA

ILLeakage Current VI = VDD or 0 V $1mA

CIInput Capacitance VI = 0 V 4.6 6 pF

I/Os

VIH High−Level Input Voltage 0.7 x VDD V

VIL Low−Level Input Voltage 0.3 x VDD V

IOL Low−Level Output Current

(Note 8) VOL = 0.5 V; VDD = 1.65 V 8 20 mA

VOL = 0.5 V; VDD = 2.3 V 12 28

VOL = 0.5 V; VDD = 3.0 V 17 35

VOL = 0.5 V; VDD = 4.5 V 25 42

IOL(tot) Total Low−Level Output Current

(Note 8) VOL = 0.5 V; VDD = 4.5 V 400 mA

VOH High−Level Output Voltage

(PCA9535E Only) IOH = −3 mA; VDD = 1.65 V 1.2 V

IOH = −4 mA; VDD = 1.65 V 1.1

IOH = −8 mA; VDD = 2.3 V 1.8

IOH = −10 mA; VDD = 2.3 V 1.7

IOH = −8 mA; VDD = 3.0 V 2.6

IOH = −10 mA; VDD = 3.0 V 2.5

IOH = −8 mA; VDD = 4.5 V 4.1

IOH = −10 mA; VDD = 4.5 V 4.0

ILInput Leakage Current VDD = 5.5 V; VI = VDD or 0 V $1mA

CI/O Input / Output Capacitance

(Note 9) 3.7 5 pF

INTERRUPT (INT)

IOL Low−Level Output Current VOL = 0.4 V 6 mA

COOutput Capacitance 2.1 5 pF

INPUTS AD0, AD1, AD2

VIH High−Level Input Voltage 0.7 x VDD V

VIL Low−Level Input Voltage 0.3 x VDD V

ILLeakage Current VI = VDD or 0 V $1mA

CIInput Capacitance 2.4 5 pF

6. The device is in standby mode after an I2C stop command.

7. The power−on reset circuit resets the I2C bus logic with VDD < VPOR and set all I/Os to logic 1 upon power−up. Thereafter, VDD must

be lower than 0.2 V to reset the part.

8. Each bit must be limited to a maximum of 25 mA and the total package limited to 400 mA due to internal busing limits.

9. The value is not tested, but verified on sampling basis.

PCA9535E, PCA9535EC

www.onsemi.com

Table 5. AC ELECTRICAL CHARACTERISTICS VDD = 1.65 V to 5.5 V; TA = −55°C to +125°C, unless otherwise specified.

Symbol Parameter

Standard Mode Fast Mode Fast Mode +

Unit

Min Max Min Max Min Max

fSCL SCL Clock Frequency 0 0.1 0 0.4 0 1.0 MHz

tBUF Bus−Free Time between a STOP and START

Condition 4.7 1.3 0.5 ms

tHD:STA Hold Time (Repeated) START Condition 4.0 0.6 0.26 ms

tSU:STA Setup Time for a Repeated START Condition 4.7 0.6 0.26 ms

tSU:STO Setup Time for STOP Condition 4.0 0.6 0.26 ms

tHD:DAT Data Hold Time 0 0 0 ns

tVD:ACK Data Valid Acknowledge Time (Note 10) 0.3 3.45 0.1 0.9 0.05 0.45 ms

tVD:DAT Data Valid Time (Note 11) 300 50 50 450 ns

tSU:DAT Data Setup Time 250 100 50 ns

tLOW LOW Period of SCL 4.7 1.3 0.5 ms

tHIGH HIGH Period of SCL 4.0 0.6 0.26 ms

tfFall Time of SDA and SCL (Notes 13 and 14) 300 20 +

0.1Cb

(Note 12)

300 120 ns

trRise Time of SDA and SCL 1000 20 +

0.1Cb

(Note 12)

300 120 ns

tSP Pulse Width of Spikes Suppressed by Input

Filter (Note 15) 50 50 50 ns

PORT TIMING: CL v 100 pF (See Figures 6, 9 and 10)

tV(Q) Data Output Valid Time (VDD = 4.5 V to 5.5 V)

(VDD = 2.3 V to 4.5 V)

(VDD = 1.65 V to 2.3 V)

200

350

550

200

350

550

200

350

550

tSU(D) Data Input Setup Time 100 100 100 ns

tH(D) Data Input Hold Time 1 1 1 ms

INTERRUPT TIMING: CL v 100 pF (See Figures 9 and 10)

tV(INT_N) Data Valid Time 4 4 4 ms

tRST(INT_N) Reset Delay Time 4 4 4 ms

10.tVD:ACK = time for Acknowledgment signal from SCL LOW to SDA (out) LOW.

11. tVD:DAT = minimum time for SDA data out to be valid following SCL LOW.

12.Cb = total capacitance of one bus line in pF.

13.A master device must internally provide a hold time of al least 300 ns for the SDA signal (refer to VIL of the SCL signal) in order to bridge

the undefined region SCL’s falling edge.

14.The maximum tf for the SDA and SCL bus lines is specified at 300 ns. The maximum fall time for the SDA output stage tf is specified at

250 ns. This allows series protection resistors to be connected between the SDA and the SCL pins and the SDA/SCL bus lines without

exceeding the maximum specified tf.

15.Input filters on the SDA and SCL inputs suppress noise spikes less than 50 ns.

PCA9535E, PCA9535EC

www.onsemi.com

Device Address

Before the bus master can access a slave device, it must

send the address of the slave it is accessing and the operation

it wants to perform (read or write) following a START

condition. The slave address of the PCA9535E and

PCA9535EC i s shown in Figure 5. Address pins AD2, AD1,

and AD0 choose 1 of 64 slave addresses. To conserve power,

no internal pull−up resistors are provided on AD2, AD1, and

AD0.

A logic 1 on the last bit of the first byte selects a read

operation while a logic 0 selects a write operation.

Figure 5. PCA9535E and PCA9535EC Device Address

R/WA6 A5 A4 A3 A2 A1 A0

programmable

slave address

Table 6. PCA9535E AND PCA9535EC ADDRESS MAP

Address Input Slave Address

AD2 AD1 AD0 A6 A5 A4 A3 A2 A1 A0 HEX

GND SCL GND 0 0 1 0 0 0 0 20h

GND SCL VDD 0 0 1 0 0 0 1 22h

GND SDA GND 0 0 1 0 0 1 0 24h

GND SDA VDD 0 0 1 0 0 1 1 26h

VDD SCL GND 0 0 1 0 1 0 0 28h

VDD SCL VDD 0 0 1 0 1 0 1 2Ah

VDD SDA GND 0 0 1 0 1 1 0 2Ch

VDD SDA VDD 0 0 1 0 1 1 1 2Eh

GND SCL SCL 0 0 1 1 0 0 0 30h

GND SCL SDA 0 0 1 1 0 0 1 32h

GND SDA SCL 0 0 1 1 0 1 0 34h

GND SDA SDA 0 0 1 1 0 1 1 36h

VDD SCL SCL 0 0 1 1 1 0 0 38h

VDD SCL SDA 0 0 1 1 1 0 1 3Ah

VDD SDA SCL 0 0 1 1 1 1 0 3Ch

VDD SDA SDA 0 0 1 1 1 1 1 3Eh

GND GND GND 0 1 0 0 0 0 0 40h

GND GND VDD 0 1 0 0 0 0 1 42h

GND VDD GND 0 1 0 0 0 1 0 44h

GND VDD VDD 0 1 0 0 0 1 1 46h

VDD GND GND 0 1 0 0 1 0 0 48h

VDD GND VDD 0 1 0 0 1 0 1 4Ah

VDD VDD GND 0 1 0 0 1 1 0 4Ch

VDD VDD VDD 0 1 0 0 1 1 1 4Eh

GND GND SCL 0 1 0 1 0 0 0 50h

GND GND SDA 0 1 0 1 0 0 1 52h

GND VDD SCL 0 1 0 1 0 1 0 54h

GND VDD SDA 0 1 0 1 0 1 1 56h

VDD GND SCL 0 1 0 1 1 0 0 58h

VDD GND SDA 0 1 0 1 1 0 1 5Ah

VDD VDD SCL 0 1 0 1 1 1 0 5Ch

PCA9535E, PCA9535EC

www.onsemi.com

Table 6. PCA9535E AND PCA9535EC ADDRESS MAP

Slave AddressAddress Input

HEXA0A1A2A3A4A5A6AD0AD1AD2

VDD VDD SDA 0 1 0 1 1 1 1 5Eh

SCL SCL GND 1 0 1 0 0 0 0 A0h

SCL SCL VDD 1 0 1 0 0 0 1 A2h

SCL SDA GND 1 0 1 0 0 1 0 A4h

SCL SDA VDD 1 0 1 0 0 1 1 A6h

SDA SCL GND 1 0 1 0 1 0 0 A8h

SDA SCL VDD 1 0 1 0 1 0 1 AAh

SDA SDA GND 1 0 1 0 1 1 0 ACh

SDA SDA VDD 1 0 1 0 1 1 1 AEh

SCL SCL SCL 1 0 1 1 0 0 0 B0h

SCL SCL SDA 1 0 1 1 0 0 1 B2h

SCL SDA SCL 1 0 1 1 0 1 0 B4h

SCL SDA SDA 1 0 1 1 0 1 1 B6h

SDA SCL SCL 1 0 1 1 1 0 0 B8h

SDA SCL SDA 1 0 1 1 1 0 1 BAh

SDA SDA SCL 1 0 1 1 1 1 0 BCh

SDA SDA SDA 1 0 1 1 1 1 1 BEh

SCL GND GND 1 1 0 0 0 0 0 C0h

SCL GND VDD 1 1 0 0 0 0 1 C2h

SCL VDD GND 1 1 0 0 0 1 0 C4h

SCL VDD VDD 1 1 0 0 0 1 1 C6h

SDA GND GND 1 1 0 0 1 0 0 C8h

SDA GND VDD 1 1 0 0 1 0 1 CAh

SDA VDD GND 1 1 0 0 1 1 0 CCh

SDA VDD VDD 1 1 0 0 1 1 1 CEh

SCL GND SCL 1 1 1 0 0 0 0 E0h

SCL GND SDA 1 1 1 0 0 0 1 E2h

SCL VDD SCL 1 1 1 0 0 1 0 E4h

SCL VDD SDA 1 1 1 0 0 1 1 E6h

SDA GND SCL 1 1 1 0 1 0 0 E8h

SDA GND SDA 1 1 1 0 1 0 1 EAh

SDA VDD SCL 1 1 1 0 1 1 0 ECh

SDA VDD SDA 1 1 1 0 1 1 1 EEh

PCA9535E, PCA9535EC

www.onsemi.com

REGISTERS

Command Byte

During a write transmission, the address byte is followed

by the command byte. The command byte determines which

of the following registers will be written or read.

Table 7. COMMAND BYTE

COMMAND REGISTER

0Input Port 0

1Input Port 1

2Output Port 0

3Output Port 1

4Polarity Inversion Port 0

5Polarity Inversion Port 1

6Configuration Port 0

7Configuration Port 1

Registers 0 and 1: Input Port Registers

These registers are input−only. They reflect the incoming

logic levels of the pins, regardless of whether the pin is

defined as an input or an output by Registers 6 or 7. Writes

to these registers have no effect.

The externally−applied logic level determines the default

value ‘X’.

Table 8. INPUT PORT 0 REGISTER

Bit 7 6 5 4 3 2 1 0

Symbol I0.7 I0.6 I0.5 I0.4 I0.3 I0.2 I0.1 I0.0

Default X X X X X X X X

Table 9. INPUT PORT 1 REGISTER

Bit 7 6 5 4 3 2 1 0

Symbol I1.7 I1.6 I1.5 I1.4 I1.3 I1.2 I1.1 I1.0

Default X X X X X X X X

Registers 2 and 3: Output Port Registers

These registers are output−only. They reflect the outgoing

logic levels of the pins defined as outputs by Registers 6 an d

7. Bit values in these registers have no effect o n pins defined

as inputs. In turn, reads from these registers reflect the values

that are in the flip−flops controlling the output selection, not

the actual pin values.

Table 10. OUTPUT PORT 0 REGISTER

Bit 7 6 5 4 3 2 1 0

Symbol O0.7 O0.6 O0.5 O0.4 O0.3 O0.2 O0.1 O0.0

Default 1 1 1 1 1 1 1 1

Table 11. OUTPUT PORT 1 REGISTER

Bit 7 6 5 4 3 2 1 0

Symbol O1.7 O1.6 O1.5 O1.4 O1.3 O1.2 O1.1 O1.0

Default 1 1 1 1 1 1 1 1

PCA9535E, PCA9535EC

www.onsemi.com

Registers 4 and 5: Polarity Inversion Registers

These registers allow the polarity of the data in the input

port registers to be inverted. The input port data polarity will

be inverted when its corresponding bit in these registers is

set (written with ‘1’), and retained when the bit is cleared

(written with a ‘0’).

Table 12. POLARITY INVERSION PORT 0 REGISTER

Bit 7 6 5 4 3 2 1 0

Symbol N0.7 N0.6 N0.5 N0.4 N0.3 N0.2 N0.1 N0.0

Default 0 0 0 0 0 0 0 0

Table 13. POLARITY INVERSION PORT 1 REGISTER

Bit 7 6 5 4 3 2 1 0

Symbol N1.7 N1.6 N1.5 N1.4 N1.3 N1.2 N1.1 N1.0

Default 0 0 0 0 0 0 0 0

Registers 6 and 7: Configuration Registers

The I/O pin directions are configured through the

configuration registers. When a bit in the configuration

registers i s set (written with ‘1’), the bit’s corresponding port

pin is enabled as an input with the output driver in

high−impedance. When a bit is cleared (written with ‘0’),

the corresponding port pin is enabled as an output. At reset,

the device’s ports are inputs.

Table 14. CONFIGURATION PORT 0 REGISTER

Bit 7 6 5 4 3 2 1 0

Symbol C0.7 C0.6 C0.5 C0.4 C0.3 C0.2 C0.1 C0.0

Default 1 1 1 1 1 1 1 1

Table 15. CONFIGURATION PORT 1 REGISTER

Bit 7 6 5 4 3 2 1 0

Symbol C1.7 C1.6 C1.5 C1.4 C1.3 C1.2 C1.1 C1.0

Default 1 1 1 1 1 1 1 1

Power−on Reset

Upon application of power, an internal Power−On Reset

(POR) holds the PCA9535E/PCA9535EC in a reset

condition while VDD is ramping up. When V DD has reached

VPOR, the reset condition is released and the

PCA9535E/PCA9535EC registers and SMBus state

machine will initialize to their default states. The reset is

typically completed by the POR and the part enabled by the

time the power supply is above VPOR. However, when doing

a power reset cycle, it is necessary to lower the power supply

below 0.2 V, and then restored to the operating voltage.

Please refer to application note AND9169/D for

recommended power−up and power−cycle reset profiles.

I/O Port (See Figure 2)

When an I/O pin is configured as an input on the

PCA9535E, FETs Q1 and Q2 are off, creating a

high−impedance input. The input voltage may be raised

above VDD to a maximum of 5.5 V. In the case of

PCA9535EC, FET Q1 has been removed and the

open−drain FET Q2 will function the same as PCA9535E.

When the I/O pin is configured as an output on the

PCA9535E, then either Q1 or Q2 is enabled, depending on

the state of the output port register. With the PCA9535EC,

an external pullup is required to pull the I/O pin HIGH when

its corresponding output port register bit is a 1. Care should

be exercised if an external voltage is applied to an I/O

configured as a n o u t p u t b e c ause of the low−impedance path

that exists between the pin and either VDD or VSS.

PCA9535E, PCA9535EC

www.onsemi.com

BUS TRANSACTIONS

Writing to the Port Registers

To transmit data to the PCA9535E/PCA9535EC, the bus

master must first send the device address with the least

significant bit set to logic 0 (see Figure 5 “PCA9535E and

PCA9535EC device address”). The command byte is sent

after the address and determines which registers will receive

the data following the command byte.

There are eight registers within the

PCA9535E/PCA9535EC. These registers are configured to

operate as four register pairs: Input Ports, Output Ports,

Polarity Inversion Ports, and Configuration Ports. Data

bytes are sent alternately to each register in a register pair

(see Figures 6 and 7). For example, if one byte is sent to

Output Port 1 (register 3), then the next byte will be stored

in Output Port 0 (register 2). There is no limitation on the

number of data bytes sent in one write transmission. In this

way, each 8−bit register may be updated independently of

the other registers.

Figure 6. Write to Output Port Registers

A2 A1 A0 0 AS A6

START condition R/W acknowledge

from slave

SCL

SDA A

write to port

data out

from port 0

tv(Q)

987654321

command byte data to port 0

DATA 0

slave address

STOP

condition

0.0

0.7

acknowledge

from slave acknowledge

from slave

data to port 1

DATA 1 1.0

1.7 A

data out

from port 1

tv(Q)

DATA VALID

A5 A4 A3 0 0 0 0 0 1 0

Figure 7. Write to Configuration Registers

A2 A1 A0 0 AS A6

START condition R/W acknowledge

from slave

SCL

SDA AP

98765432

command byte data to register

DATA 0

slave address

STOP

condition

LSB

MSB

acknowledge

from slave acknowledge

from slave

data to register

DATA 1

LSB

MSB

AA5 A4 A3 0 0 0 1 1 00

Reading the Port Registers

To read data from the PCA9535E/PCA9535EC, the bus

master must first send the PCA9535E/PCA9535EC address

with the least significant bit set to logic 0 (see Figure 5

“PCA9535E and PCA9535EC device address”). The

command byte is sent after the address and determines

which register will be accessed.

After a restart, the device address must be sent again, but

this time, the least significant bit is set to logic 1. Data from

the register defined by the command byte will then be sent

by the PCA9535E/PCA9535EC (see Figures 8, 9 and 10).

Data is clocked into the register on the falling edge of the

acknowledge clock pulse. After the first byte is read,

additional bytes may be read but with data alternately

coming from each register in the pair. For example, if you

read Input Port 1, then the next byte read would be

Input Port 0. There is no limitation on the number of data

bytes received in one read transmission but the bus master

must not acknowledge the data for the final byte received.

PCA9535E, PCA9535EC

www.onsemi.com

Figure 8. Read from Register

Remark: Transfer can be stopped at any time by a STOP condition.

START condition R/W

acknowledge

from slave

acknowledge

from slave

SDA

acknowledge

from master

DATA (first byte)

slave address

STOP

condition

(repeated)

START condition

(cont.)

(cont.) A2 A1 A0 1AA6

R/W

acknowledge

from slave

slave address

at this moment master−transmitter becomes master−receiver

and slave−receiver becomes slave−transmitter

no acknowledge

from master

COMMAND BYTE

A2 A1 A0A6 0

data from lower or

upper byte of register

LSB

MSB

DATA (last byte)

data from upper or

lower byte of register

LSB

MSB

A5 A4 A3

Figure 9. Read from Input Port Register, Scenario 1

Remark: Transfer of data can be stopped at any moment by a STOP condition. When this occurs, data present at the latest acknowledge

phase is valid (output mode). It is assumed that the command byte has previously been set to ’00’ (read Input Port register).

A2A1 A0 1 AS A6

START condition R/W

acknowledge

from slave

SCL

SDA A

read from port 0

98765432

I0.xslave address

STOP condition

acknowledge

from master

I1.x

acknowledge

from master

I0.x

acknowledge

from master

I1.x

non acknowledge

from master

data into port 0

read from port 1

data into port 1

INT tv(INT_N) trst(INT_N)

A5A4A3 6543210 6543210 6543210 6543210

Figure 10. Read from Input Port Register, Scenario 2

Remark: Transfer of data can be stopped at any moment by a STOP condition. When this occurs, data present at the latest acknowledge

phase is valid (output mode). It is assumed that the command byte has previously been set to ’00’ (read Input Port register).

A2A1 A0 1 AS A6

START condition

R/W

acknowledge

from slave

SCL

SDA A

read from port 0

98765432

I0.xslave address STOP condition

acknowledge

from master

I1.x

acknowledge

from master

I0.x

acknowledge

from master

I1.x

non acknowledge

from master

data into port 0

read from port 1

data into port 1

INT tv(INT_N) trst(INT_N)

21ATAD30ATAD01ATAD00ATAD

DATA 00 DATA 01 th(D)

th(D)

DATA 02

tsu(D)

DATA 03

tsu(D)

21ATAD11ATAD01ATAD

A5A4 A3

PCA9535E, PCA9535EC

www.onsemi.com

Interrupt Output

The open−drain interrupt output is activated when an I/O

pin configured as an input changes state. The interrupt is

deactivated when the input pin returns to its previous state

or when the Input Port register is read (see Figure 9). A pin

configured as an output cannot cause an interrupt. Since

each 8−bit port is read independently, the interrupt caused by

Port 0 will not be cleared by a read of Port 1 or the other way

around.

Remark: Changing an I/O from an output to an input may

cause a false interrupt to occur if the state of the pin does not

match the contents of the Input Port register.

APPLICATION INFORMATION

Figure 11. Typical Application

Device address configured as 0100 000xb for this example.

IO0_0, IO0_2, IO0_3 configured as outputs.

IO0_1, IO0_4, IO0_5 configured as inputs.

IO0_6, IO0_7, and IO1_0 to IO1_7 configured as inputs.

PCA9535E

IO0_0

IO0_1

SCL

SDA

VDD

(5 V)

MASTER

CONTROLLER

INT IO0_2

VDD

AD2

AD1

AD0

VDD

GND

INT

10 kWSUB−SYSTEM 1

(e.g., temp sensor)

IO0_3

INT

SUB−SYSTEM 2

(e.g., counter)

RESET

controlled

switch

(e.g.,7SB or FST)

VDD

ENABLE

SUB−SYSTEM 3

(e.g., alarm system)

ALARM

IO0_4

IO0_5

IO0_6

10 DIGIT

NUMERIC

KEYPAD

VSS

10 kW10 kW2 kW

IO0_7

IO1_0

IO1_1

IO1_2

IO1_3

IO1_4

IO1_5

IO1_6

IO1_7

SDA

SCL

100 kW

(x3)

Minimizing IDD When the I/Os are Used to Control

LEDs

To use the PCA9535E I/Os to control LEDs, the I/Os are

normally connected to VDD through a resistor as shown in

Figure 11. The LED acts as a diode. When the LED is off,

the I/O VI is about 1.2 V less than VDD. The supply current,

IDD, increases as VI becomes lower than VDD.

For applications requiring low current consumption, such

as battery power applications, it is recommended that the I/O

pin voltages be greater than or equal to VDD when the LED

is off. This would minimize current consumption. Figure 12

shows a high value resistor in parallel with the LED.

Figure 13 shows VDD less than the LED supply voltage by

at least 1.2 V. Both of these methods maintain the I/O VI at

or above VDD and prevents additional supply current

consumption when the LED is off.

This concern does not occur for the PCA9535EC because

the PCA9535EC I/O pins are open−drain.

PCA9535E, PCA9535EC

www.onsemi.com

Figure 12. High Value Resistor in Parallel

with the LED Figure 13. Device Supplied by a Lower Voltage

LED

VDD

LEDn

100 kW

VDD

LED

VDD

LEDn

3.3 V 5 V

Characteristics of the I2C−bus

The I2C−bus is meant for 2−way, 2−line communication

between different ICs or modules. The two lines are the

serial data line (SDA) and the serial clock line (SCL). Both

lines must be connected to a positive supply via a pull−up

resistor when connected to the output stages of a device.

Data transfer may only be initiated when the bus is not busy.

Bit transfer

One data bit is transferred during each clock pulse. The

data on the SDA line must remain stable during the HIGH

period of the clock pulse. Changes in the data line during the

HIGH period of the clock pulse will be interpreted as control

signals (see Figure 14).

Figure 14. Bit Transfer

data line

stable;

data valid

change

of data

allowed

SDA

SCL

START and STOP conditions

Both data and clock lines remain HIGH when the bus is

not busy. A START condition (S) occurs when there is a

HIGH−to−LOW transition of the data line while the clock is

HIGH. A STOP condition (P) occurs when there is a

LOW−to−HIGH transition of the data line while the clock is

HIGH (see Figure 15).

Figure 15. Definition of START and STOP Conditions

SDA

SCL P

STOP condition

SDA

SCL

START condition

PCA9535E, PCA9535EC

www.onsemi.com

System Configuration

A device generating a message is a ‘transmitter’; a device

receiving is the ‘receiver’. The device that controls the

message i s the ‘master’ and the devices which are controlled

by the master are the ‘slaves’ (see Figure 16).

Figure 16. System Configuration

MASTER

TRANSMITTER/

RECEIVER

SLAVE

RECEIVER SLAVE

TRANSMITTER/

RECEIVER

MASTER

TRANSMITTER MASTER

TRANSMITTER/

RECEIVER

SDA

SCL

I2C−BUS

MULTIPLEXER

SLAVE

Acknowledge

The number of data bytes transferred between the START

and the STOP conditions from transmitter to receiver is not

limited. Each 8−bit byte is followed by one acknowledge bit.

The acknowledge bit is a HIGH level put on the bus by the

transmitter, whereas the master generates an extra clock

pulse for the acknowledge bit.

A slave receiver which is addressed must generate an

acknowledge after the reception of each byte. Also a master

must generate an acknowledge after the reception of each

byte that has been clocked out of the slave transmitter. The

device that acknowledges has to pull down the SDA line

during the acknowledge clock pulse, such that the SDA line

is stable LOW during the HIGH period of the acknowledge

clock pulse; set−up time and hold time must be taken into

account.

A master receiver signals an end of data to the transmitter

by not generating an acknowledge on the last byte that has

been clocked out of the slave. In this event, the transmitter

must leave the data line HIGH to enable the master to

generate a STOP condition.

Figure 17. Acknowledgement of the I2C Bus

START

condition

9821

clock pulse for

acknowledgement

not acknowledge

acknowledge

data output

by transmitter

data output

by receiver

SCL from master

Timing and Test Setup

Figure 18. Definition of Timing on the I2C Bus

tSP

tBUF

tHD;STA PP S

tLOW

tHD;DAT

tHIGH tSU;DAT tSU;STA

tHD;STA

tSU;STO

SDA

SCL

PCA9535E, PCA9535EC

www.onsemi.com

Rise and fall times refer to VIL and VIH

Figure 19. I2C Bus Timing Diagram

SCL

SDA

tHD;STA tSU;DAT tHD;DAT

tBUF

tSU;STA tLOW tHIGH

tVD;ACK tSU;STO

protocol START

condition

(S)

bit 7

MSB

(A7)

bit 6

(A6) acknowledge

(A) (P)

1/fSCL

tVD;DAT

Figure 20. tV(Q) Timing

tv(Q)

SCL

IOn

tv(Q)

SCL

IOn

Figure 21. Test Circuitry for Switching Times

PULSE

GENERATOR

50 pF

500 W

VDD

DUT

VDD

open

GND

RL = load resistor.

CL = load capacitance includes jig and probe capacitance.

RT = termination resistance should be equal to the output impedance of Zo of the pulse generators.

Figure 22. Load Circuit

50 pF RL

500 W

from output under test 2VDD

open

GND

500 W

PCA9535E, PCA9535EC

www.onsemi.com

ORDERING INFORMATION

Device Package Shipping†

PCA9535EDWR2G SOIC−24

(Pb−Free) 1000 / Tape & Reel

PCA9535EDTR2G,

NLVPCA9535EDTR2G* TSSOP−24

(Pb−Free) 2500 / Tape & Reel

PCA9535EMTTXG WQFN24

(Pb−Free) 3000 / Tape & Reel

PCA9535ECDWR2G SOIC−24

(Pb−Free) 1000 / Tape & Reel

PCA9535ECDTR2G TSSOP−24

(Pb−Free) 2500 / Tape & Reel

PCA9535ECMTTXG WQFN24

(Pb−Free) 3000 / Tape & Reel

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging

Specifications Brochure, BRD8011/D.

*NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP

Capable.

PCA9535E, PCA9535EC

www.onsemi.com

PACKAGE DIMENSIONS

SOIC−24 WB

CASE 751E−04

ISSUE F

0.25 C

SEATING

PLANE

DETAIL A

END VIEW

NOTES:

1. DIMENSIONING AND TOLERANCING PER ASME

Y14.5M, 1994.

2. CONTROLLING DIMENSION: MILLIMETERS.

3. DIMENSIONS b AND c APPLY TO THE FLAT SEC-

TION OF THE LEAD AND ARE MEASURED BE-

TWEEN 0.10 AND 0.25 FROM THE LEAD TIP.

4. DIMENSIONS D AND E1 DO NOT INCLUDE MOLD

FLASH, PROTRUSIONS OR GATE BURRS. MOLD

FLASH, PROTRUSIONS OR GATE BURRS SHALL

NOT EXCEED 0.15 mm PER SIDE. INTERLEAD

FLASH OR PROTRUSION SHALL NOT EXCEED

0.25 PER SIDE. DIMENSIONS D AND E1 ARE

DETERMINED AT DATUM H.

5. A1 IS DEFINED AS THE VERTICAL DISTANCE

FROM THE SEATING PLANE TO THE LOWEST

POINT ON THE PACKAGE BODY.

NOTE 3

PIN 1

24 13

TOP VIEW DIM MIN MAX

MILLIMETERS

A2.35 2.65

b0.35 0.49

e1.27 BSC

h0.25 0.75

c0.23 0.32

A1 0.13 0.29

L0.41 0.90

M0 8

SIDE VIEW

11.00

24X

0.52 24X

1.62

1.27

DIMENSIONS: MILLIMETERS

1PITCH

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

SOLDERING FOOTPRINT*

E10.30 BSC

RECOMMENDED

INDICATOR A B

0.25 C

24X

NOTE 5

x 45

NOTE 3 DET AIL A

D15.25 15.54

E1 7.40 7.60

S S

PCA9535E, PCA9535EC

www.onsemi.com

PACKAGE DIMENSIONS

TSSOP24 7.8x4.4, 0.65P

CASE 948H

ISSUE B

DIM

MIN MAX

7.90

MILLIMETERS

E1 4.30 4.50

A1.20

A1 0.05 0.15

L0.50 0.75

e0.65 BSC

c0.09 0.20

b0.19 0.30

L2 0.25 BSC

M0 8

NOTES:

1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.

2. CONTROLLING DIMENSION: MILLIMETERS.

3. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION.

DAMBAR PROTRUSION SHALL BE 0.08 MAX AT MMC. DAMBAR

CANNOT BE LOCATED ON THE LOWER RADIUS OF THE FOOT.

4. DIMENSION D DOES NOT INCLUDE MOLD FLASH,

PROTRUSIONS OR GATE BURRS. MOLD FLASH,

PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15

PER SIDE. DIMENSION D IS DETERMINED AT DATUM PLANE H.

5. DIMENSION E1 DOES NOT INCLUDE INTERLEAD FLASH OR

PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL

NOT EXCEED 0.25 PER SIDE. DIMENSION E1 IS DETERMINED

AT DATUM PLANE H.

6. DATUMS A AND B ARE DETERMINED AT DATUM PLANE H.

7. A1 IS DEFINED AS THE VERTICAL DISTANCE FROM THE SEAT-

ING PLANE TO THE LOWEST POINT ON THE PACKAGE BODY.

7.70

---

24X

1.15

24X 0.42

0.65

DIMENSIONS: MILLIMETERS

PITCH

SOLDERING FOOTPRINT

E6.40 BSC

6.70

RECOMMENDED

GAUGE

DETAIL A

PLANE

DET AIL A

END VIEW

0.10

SEATING

PLANE

SIDE VIEW

0.05 C

24X

PIN 1

REFERENCE

24X b

0.10 AC

TOP VIEW

B0.15 C

112

1324

NOTE 3

2X 12 TIPS

NOTE 6

NOTE 4

NOTE 5

S S

PCA9535E, PCA9535EC

www.onsemi.com

PACKAGE DIMENSIONS

WQFN24 4x4, 0.5P

CASE 485BG

ISSUE A

NOTES:

1. DIMENSIONING AND TOLERANCING PER ASME

Y14.5M, 1994.

2. CONTROLLING DIMENSION: MILLIMETERS.

3. DIMENSION b APPLIES TO PLATED TERMINAL

AND IS MEASURED BETWEEN 0.15 AND 0.30 MM

FROM TERMINAL TIP.

4. COPLANARITY APPLIES TO THE EXPOSED PAD

AS WELL AS THE TERMINALS.

ÇÇÇÇ

C0.15

PIN ONE

REFERENCE

TOP VIEW

SIDE VIEW

BOTTOM VIEW

C0.15

C0.10

C0.08

A1 SEATING

PLANE

24X

NOTE 3

24X

0.10 C

0.05 C

ABB

DIM MIN MAX

MILLIMETERS

A0.70 0.80

A1 0.00 0.05

b0.20 0.30

D4.00 BSC

D2 2.00 2.20

E4.00 BSC

E2 2.00 2.20

e0.50 BSC

K0.20 −−−

L0.30 0.50

24X

0.50

PITCH

4.30

0.63

4.30

DIMENSIONS: MILLIMETERS

0.30

24X

A3 0.20 REF

MOUNTING FOOTPRINT*

NOTE 4

DETAIL B

2.26

PACKAGE

OUTLINE

DET AIL A

e/2

DETAIL A

ALTERNATE TERMINAL

CONSTRUCTIONS

ÉÉÉ

DETAIL B

MOLD CMPDEXPOSED Cu

ALTERNATE

CONSTRUCTION L1 0.00 0.15

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

ON Semiconductor and the are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.

SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed

at www.onsemi.com/site/pdf/Patent − Marking.pdf. S CILLC r eserves the r ight to make changes without f urther n otice to any product s herein. S CILLC makes n o warranty, representation

or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and

specifically disclaims any and all l iabilit y, including without limitation special, c onsequent ial o r i ncident al d amages. “Typical” parameters w hich may be provided in SCILLC data sheet s

and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each

customer application b y c ust omer’s technical e xperts. SCILLC does not c onvey a ny l icense u nder its patent r ight s n or the rights of o thers. SCILLC products a re n ot d esigned, i nt ended,

or authorized for use as c omponent s i n s yst ems i nt ended f or s urgic al i m plant i nt o the body, or other applications intended t o s upport o r s ust ain life, o r for any other application in which

the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or

unauthorized application, Buyer shall indemnify and hold SCILLC an d it s officers, employees, subsidiar ies, a ffiliates, and distributors harmless against all claims, costs, damages, and

expenses, and r easonable a ttorney f ees a rising o ut of, directly o r i ndirectly, any c laim o f p ersonal i njury o r d eath a ssociated w ith s uch u nint ended o r u nauthorized u se, even if s uch c laim

alleges that SCILLC was negligent regarding the d esign or manufacture of the p art. SCILLC is a n Equal O pportunit y/Aff irmative A ction E mployer . T his l iterature i s subject t o all applicable

UBLICATION ORDERING INFORMATION

N. American Technical Support: 800−282−9855 Toll Free

USA/Canada

Europe, Middle East and Africa Technical Support:

Phone: 421 33 790 2910

Japan Customer Focus Center

Phone: 81−3−5817−1050

PCA9535E/D

LITERATURE FULFILLMENT:

Literature Distribution Center for ON Semiconductor

19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA

Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada

Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

ON Semiconductor Website: www.onsemi.com

Order Literature: http://www.onsemi.com/orderlit

For additional information, please contact your loc

Sales Representative