LMR33630CDDAR - TEXAS INSTRUMENTS

January, 2013 − Rev. 2

1Publication Order Number:

NCP605/D

NCP605, NCP606

500mA, Low IGND, CMOS

LDO Regulator with/without

Enable and with Enhanced

ESD Protection

The NCP605/NCP606 provide in excess of 500 mA of output

current at fixed voltage options or an adjustable output voltage from

5.0 V down to 1.25 V. These devices are designed for space

constrained and portable battery powered applications and offer

additional features such as high PSRR, low noise operation, short

circuit and thermal protection. The devices are designed to be used

with low cost ceramic capacitors and are packaged in the DFN6 3x3.3.

NCP605 is designed without enable pin, NCP606 is designed with

enable pin.

Features

•Output Voltage Options:

Adjustable, 1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V

•Adjustable Output by External Resistors from 5.0 V down to 1.25 V

•Current Limit 675 mA

•Low IGND (Independent of Load)

•$1.5% Output Voltage Tolerance Over All Operating Conditions

(Adjustable)

•$2% Output Voltage Tolerance Over All Operating Conditions

(Fixed)

•NCP605 Fixed is Direct Replacement LP8345

•Typical Noise Voltage of 50 mVrms without a Bypass Capacitor

•Enhanced ESD Ratings: 4 kV Human Body Mode (HBM)

200 V Machine Model (MM)

•These are Pb−Free Devices

Typical Applications

•Hard Disk Drivers

•Notebook Computers

•Battery Power Electronics

•Portable Instrumentation

Figure 1. NCP605 Typical Application Circuit for Fixed

Version (1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V)

NCP605

(Fixed)

Vin Vout

SENSE

GND

Vout

Vin

Cin Cout

DFN6, 3x3.3

MN SUFFIX

CASE 506AX

See detailed ordering and shipping information in the package

dimensions section on page 12 of this data sheet.

ORDERING INFORMATION

MARKING

DIAGRAM

http://onsemi.com

1xxxx

zzz

AYWWG

xxxx = P605 or P606

zzz = ADJ, 150, 180, 250, 280,

300, 330, 500

A = Assembly Location

Y = Year

WW = Work Week

G= Pb−Free Package

(*Note: Microdot may be in either location)

GND

SENSE/ADJ

GND

SENSE/ADJ

GND

NCP605 PIN CONNECTIONS

DFN6 3x3.3mm

NCP606 PIN CONNECTIONS

DFN6 3x3.3mm

(TOP VIEW)

Vin Vin

Vout

Vin Vin

Vout

NCP605, NCP606

http://onsemi.com

Figure 2. NCP606 Typical Application Circuit for Fixed Version (1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V)

NCP606

(Fixed)

Vin Vout

SENSE

GND

Vout

Vin

Cin Cout

Figure 3. NCP605 Typical Application Circuit for

Adjustable Version (1.25 V < Vout v 5.0 V)

NCP605

(Adjustable)

Vin Vout

ADJ

GND

Vout

Vin

Cin Cout

NCP606

(Adjustable)

Vin Vout

ADJ

GND

Vout

Vin

Cin Cout

Figure 4. NCP606 Typical Application Circuit for

Adjustable Version (1.25 V < Vout v 5.0 V)

Figure 5. NCP605 Typical Application Circuit for

Adjustable Version (Vout = 1.25 V)

NCP605

(Adjustable)

Vin Vout

ADJ

GND

Vout

Cin Cout

Figure 6. NCP606 Typical Application Circuit for

Adjustable Version (Vout = 1.25 V)

NCP606

(Adjustable)

Vin Vout

ADJ

GND

Vout

Cin Cout

Vin Vin

Figure 7. NCP605 Simplified Block

Diagram

Figure 8. NCP606 Simplified Block

Diagram

−

Driver with

Current Limit

Thermal

Shutdown Vref

GND

SENSE/ADJ

Fixed Version Only

Adjustable

Version Only

−

Driver with

Current Limit

Thermal

Shutdown Vref

GND

SENSE/ADJ

Fixed Version Only

Adjustable

Version Only

Vin Vout Vin Vout

NCP605, NCP606

http://onsemi.com

PIN FUNCTION DESCRIPTION

Pin No. Pin Name Description

1 Vin Positive Power Supply Input*

2 GND Power Supply Ground

3 NC/EN NCP605: This Pin is Not Connected

NCP606: This Pin is Enable Input, Active HIGH

4 Vout Regulated Output Voltage

5 SENSE/ADJ Output Voltage Sense Input

Fixed Version: Connect Directly to Output Capacitor

Adjustable Version: Connect to Middle Point of External Resistor Divider

6 Vin Positive Power Supply Input*

EPAD GND Exposed Pad is Connected to Ground

*Pins 1 and 6 must be connected together externally for output current full range operation

ABSOLUTE MAXIMUM RATINGS

Rating Symbol Value Unit

Input Voltage Range (Note 1) Vin −0.3 to 6.5 V

Chip Enable Voltage Range (NCP606 only) VEN −0.3 to 6.5 V

Output Voltage Range Vout −0.3 to 6.5 V

Output Voltage/Sense Input Range, SENSE/ADJ VADJ −0.3 to 6.5 V

ESD Capability Human Body Model

Machine Model

ESD 4000

200

Maximum Junction Temperature TJ(MAX) 150 °C

Storage Temperature Range TSTG −65 to 150 °C

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the

Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect

device reliability.

NOTE: This device series contains ESD Protection and exceeds the following tests:

ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114)

ESD Machine Model tested per AEC− 150 mA per JEDEC standard: JESD78Q100−003 (EIA/JESD22−A115)

Latchup Current Maximum Rating: v 150 mA per JEDEC standard: JESD78.

1. Minimum Vin = (Vout + VDO) or 1.5 V, whichever is higher.

THERMAL CHARACTERISTICS

Rating Symbol Value Unit

Thermal Resistance, Junction−to−Ambient (Note 2) RqJA 75 °C/W

Thermal Resistance, Junction−to−Case RYJC 18 °C/W

2. Soldered on 645 mm2, 1 oz copper area, FR4. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe

Operating Area.

OPERATING RANGES (Note 3)

Rating Symbol Value Unit

Input Voltage (Note 4) Vin 1.5 to 6.0 V

Output Current (Notes 5 and 6) Iout 0 to 675 mA

Junction Temperature TJ−40 to 150 °C

Ambient Temperature TA−40 to 125 °C

3. Refer to Electrical Characteristics and Application Information for Safe Operating Area.

4. Minimum Vin = (Vout + VDO) or 1.5 V, whichever is higher.

5. Minimum limit valid for fixed versions only. For more details refer to Application Information Section.

6. Maximum limit for Vout = Vout(nom) − 10%.

NCP605, NCP606

http://onsemi.com

ELECTRICAL CHARACTERISTICS

Vin = (Vout + 0.5 V) or 1.5 V, whichever is higher, Cin = 1 mF, Cout = 1 mF, for typical values TA = 25°C, for min/max values TA = −40°C to

85°C; unless otherwise noted. (Notes 9 and 10)

Parameter Test Conditions Symbol Min Typ Max Unit

Output voltage (Adjustable Version) Vin = 1.75 V to 6 V

Iout = 1 mA to 500 mA

Vout 1.231

(−1.5%)

1.250 1.269

(+1.5%)

Output voltage (Fixed Versions) 1.5 V

1.8 V

2.5 V

2.8 V

3.0 V

3.3 V

5.0 V

Vin = (Vout + 0.5 V) to 6 V

Iout = 1 mA to 500 mA

Vout 1.470

1.764

2.450

2.744

2.940

3.234

4.900

(−2%)

1.5

1.8

2.5

2.8

3.0

3.3

5.0

1.530

1.836

2.550

2.856

3.060

3.366

5.100

(+2%)

Line regulation Vin = (Vout + 0.5 V) to 6 V, Iout = 1 mA Regline −4 10 mV

Load regulation Iout = 1 mA to 500 mA Regload −10 30 mV

Dropout voltage (Adjustable Version)

(Note 9)

VDO = Vin − Vout

Vout = 1.25 V

Iout = 500 mA

VDO

−450 470

Dropout voltage (Fixed Version)

1.5 V

1.8 V

2.5 V

2.8 V

3.0 V

3.3 V

5.0 V

VDO = Vin − (Vout − 0.1 V)

Iout = 500 mA

Vout = 0 V to 90% Vout(nom)

VDO

−

290

250

200

190

180

170

150

360

300

250

240

230

220

200

Disable Current (NCP606 Only) (Note 10) VEN = 0 V IDIS −0.1 1 mA

Ground Current Iout = 1 mA to 500 mA IGND −145 180 mA

Current Limit (Note 11) Vout = Vout(nom) − 10 % ILIM 675 − − mA

Output Short Circuit Current Vout = 0 V ISC 700 1000 1350 mA

Enable Input Threshold Voltage

(NCP606 Only)

Voltage Increasing, Logic High

Voltage Decreasing, Logic Low

High

Low

Vth(EN)

0.9

−

0.4

Turn−on Time (Note 11)

1.25 V

1.5 V

1.8 V

2.5 V

2.8 V

3.0 V

3.3 V

5.0 V

Vin = 0 V to (Vout + 0.5 V) or 1.75 V,

whichever is higher

Vout = 0 V to 90% of Vout(nom)

ton

−

Enable Time (NCP606 Only) (Note 11)

1.25 V

1.5 V

1.8 V

2.5 V

2.8 V

3.0 V

3.3 V

5.0 V

VEN = From 0 V to Vin tEN

−

7. Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area.

8. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at TJ = TA = 25°C. Low

duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.

9. Maximum dropout voltage is limited to minimum input voltage Vin = 1.7 V recommended for guaranteed operation at maximum output

current.

10.Refer to application information section.

11. Values based on design and/or characterization.

NCP605, NCP606

http://onsemi.com

ELECTRICAL CHARACTERISTICS

Vin = (Vout + 0.5 V) or 1.5 V, whichever is higher, Cin = 1 mF, Cout = 1 mF, for typical values TA = 25°C, for min/max values TA = −40°C to

85°C; unless otherwise noted. (Notes 9 and 10)

Parameter UnitMaxTypMinSymbolTest Conditions

Power Supply Ripple Rejection (Note 11) Iout = 500 mA

Vout = 1.25 V

Vin − Vout = 1 V

f = 120 Hz, 0.5 VPP

f = 1 kHz, 0.5 VPP

f = 10 kHz, 0.5 VPP

PSRR

−

Output Noise Voltage (Note 11) f = 10 Hz to 100 kHz, Vout = 1.25 V Vn−50 −mVrms

Thermal Shutdown Temperature (Note 11) TSD −175 −°C

Thermal Shutdown Hysteresis (Note 11) TSH −10 −°C

7. Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area.

8. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at TJ = TA = 25°C. Low

duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.

9. Maximum dropout voltage is limited to minimum input voltage Vin = 1.7 V recommended for guaranteed operation at maximum output

current.

10.Refer to application information section.

11. Values based on design and/or characterization.

NCP605, NCP606

http://onsemi.com

TYPICAL CHARACTERISTICS

Figure 9. Output Voltage vs. Temperature

(Vout = 1.25 V)

1.231

1.2348

1.2386

1.2424

1.2462

1.25

1.2538

1.2576

1.2614

1.2652

1.269

−40 −20 0 20 40 60 80 100

TA, AMBIENT TEMPERATURE (°C)

Vout, OUTPUT VOLTAGE (V)

Vin = Vout + 0.5 V = 1.75 V

Vin = 6.0 V

Vout = 1.25 V

Figure 10. Output Voltage vs. Temperature

(Vout = 2.5 V)

2.45

2.46

2.47

2.48

2.49

2.5

2.51

2.52

2.53

2.54

2.55

−40 −20 0 20 40 60 80 100

TA, AMBIENT TEMPERATURE (°C)

Vout, OUTPUT VOLTAGE (V)

Vin = Vout + 0.5 V = 3.0 V

Vin = 6.0 V

Vout = 2.5 V

Figure 11. Output Voltage vs. Temperature

(Vout = 5.0 V)

4.9

4.92

4.94

4.96

4.98

5.02

5.04

5.06

5.08

5.1

−40 −20 0 20 40 60 80 100

Vout, OUTPUT VOLTAGE (V)

TA, AMBIENT TEMPERATURE (°C)

Vin = 6.0 V

Vin = Vout + 0.5 V = 5.5 V

Figure 12. Dropout Voltage vs. Temperature

(Vout = 2.5 V)

120

150

180

210

240

270

300

−40 −20 0 20 40 60 80 100

VDO, DROPOUT VOLTAGE (mV)

TA, AMBIENT TEMPERATURE (°C)

Iout = 500 mA

Iout = 300 mA

Iout = 150 mA

Figure 13. Dropout Voltage vs. Temperature

(Vout = 5.0 V)

100

120

140

160

180

200

−40 −20 0 20 40 60 80 100

TA, AMBIENT TEMPERATURE (°C)

VDO, DROPOUT VOLTAGE (mV)

Iout = 150 mA

Iout = 300 mA

Iout = 500 mA

Figure 14. Ground Current vs. Temperature

100

110

120

130

140

150

160

170

180

−40 −200 204060801

TA, AMBIENT TEMPERATURE (°C)

IGND, GROUND CURRENT (mA)

Vout = 5.0 V

Vout = 2.5 V

Vout = 1.25 V

Vin = Vout + 0.5 V

Iout = 500 mA

Vout = 5.0 V Vout = 2.5 V

Vout = 5.0 V

NCP605, NCP606

http://onsemi.com

TYPICAL CHARACTERISTICS

Figure 15. Short Circuit Current Limit vs.

Temperature (Vout = 1.25 V)

800

840

880

920

960

1000

1040

1080

1120

1160

1200

−40 −20 0 20 40 60 80 100

TA, AMBIENT TEMPERATURE (°C)

ISC, SHORT CIRCUIT CURRENT LIM-

IT (mA)

Vin = 1.75 V

Vin = 6.0 V

Figure 16. PSRR vs. Frequency (Vout = 1.25 V)

f, FREQUENCY (Hz)

PSRR (dB)

Vout = 1.25 V

Vin = 2.25 V

Cout = 1.0 mF

TA = 25°C

Iout = 500 mA Iout = 1mA

Figure 17. PSRR vs. Frequency (Vout = 2.5 V)

10 100 1000 10000 100000

PSRR (dB)

f, FREQUENCY (Hz)

Vout = 2.5 V

Vin = 3.5 V

Cout = 1.0 mF

TA = 25°C

Iout = 500 mA Iout = 1mA

Figure 18. Noise Density vs. Frequency

(Vout = 1.25 V)

200

400

600

800

1000

1200

1400

1600

10 100 1000 10000 100000

f, FREQUENCY (Hz)

Vn, NOISE DENSITY (nV/√/HZ)

Vin = Vout + 0.5 V = 1.75 V

Cin = Cout = 1.0 mF

Iout = 500 mA

TA = 25°C

Vn = 47 mVrms

Figure 19. Noise Density vs. Frequency

(Vout = 2.5 V)

500

1000

1500

2000

2500

10 100 1000 10000 100000

f, FREQUENCY (Hz)

Vn, NOISE DENSITY (nV/√/HZ)

Vin = Vout + 0.5 V = 3.0 V

Cin = Cout = 1.0 mF

Iout = 500 mA

TA = 25°C

Vn = 70 mVrms

Figure 20. Load Transient (Vout = 2.5 V)

TIME (40 ms/div)

Vout

200 mV/div

Iout

500 mA/div

Vin = 3.0 V

Vout = 2.5 V

Cout = 10 mF

trise = tfall = 1 ms

TA = 25°C

Vout = 1.25 V

10 100 1000 10000 100000

NCP605, NCP606

http://onsemi.com

TYPICAL CHARACTERISTICS

Figure 21. Line Transient (Vout = 2.5 V)

TIME (20 ms/div)

Vin = 2.5 V

Iout = 500 mA

Cout = 10 mF

trise = tfall = 1 ms

TA = 25°C

Vout

100 mV/div

Vin

500 mV/div

4.0 V

3.0 V

Figure 22. Startup Transient (Vout = 2.5 V)

TIME (10 ms/div)

Vout

1 V/div

Vin

1 V/div

Vout = 2.5 V

Iout = 0 mA

Cout = 10 mF

Vin = 3.0 V

trise = 1 ms

TA = 25°C

NCP605, NCP606

http://onsemi.com

DEFINITIONS

General

All measurements are performed using short pulse low

duty cycle techniques to maintain junction temperature as

close as possible to ambient temperature.

Line Regulation

The change in output voltage for a change in input voltage.

The measurement is made under conditions of low

dissipation or by using pulse techniques such that the

average junction temperature is not significantly affected.

Load Regulation

The change in output voltage for a change in output load

current at a constant temperature.

Dropout Voltage

The input to output differential at which the regulator

output no longer maintains regulation against further

reductions in input voltage. Measured when the output drops

100 mV below its nominal value. The junction temperature,

load current, and minimum input supply requirements affect

the dropout level.

Ground and Disable Currents

Ground Current is the current that flows through the

ground pin when the regulator operates without a load on its

output (IGND). This consists of internal IC operation, bias,

etc. It is actually the difference between the input current

(measured through the LDO input pin) and the output load

current. If the regulator has an input pin that reduces its

internal bias and shuts off the output (enable/disable

function), this term is called the disable current (IDIS).

Current Limit and Short Circuit Current Limit

Current Limit is value of output current by which output

voltage drops by 10% with respect to its nominal value.

Short Circuit Current Limit is output current value

measured with output of the regulator shorted to ground.

PSRR

Power Supply Rejection Ratio is defined as ratio of output

voltage and input voltage ripple. It is measured in decibels

(dB).

Output Noise Voltage

This is the integrated value of the output noise over a

specified frequency range. Input voltage and output load

current are kept constant during the measurement. Results

are expressed in mVrms or nV / √Hz.

Turn−on and Turn−off Times

Turn−on Time is time difference measured during

power−up of the device from the moment when input

voltage reaches 90% of its operating value to the moment

when output voltage reaches 90% of its nominal value at

specific output current or resistive load.

Turn−off Time is time difference measured during

power−down of the device from the moment when input

voltage drops to 10% of its operating value to the moment

when output voltage drops to 10% of its nominal value at

specific output current or resistive load.

Enable and Disable Times

Enable Time is time difference measured during

power−up of the device from the moment when enable

voltage reaches 90% of input voltage operating value to the

moment when output voltage reaches 90% of its nominal

value at specific output current or resistive load.

Disable Time is time difference measured during

power−down of the device from the moment when enable

voltage drops to 10% of input voltage operating value to the

moment when output voltage drops to 10% of its nominal

value at specific output current or resistive load.

Line Transient Response

Typical output voltage overshoot and undershoot response

when the input voltage is excited with a given slope.

Load Transient Response

Typical output voltage overshoot and undershoot

response when the output current is excited with a given

slope between no−load and full−load conditions.

Thermal Protection

Internal thermal shutdown circuitry is provided to protect

the integrated circuit in the event that the maximum junction

temperature is exceeded. When activated at typically 175°C,

the regulator turns off. This feature is provided to prevent

failures from accidental overheating.

Maximum Package Power Dissipation

The power dissipation level at which the junction

temperature reaches its maximum operating value.

NCP605, NCP606

http://onsemi.com

APPLICATIONS INFORMATION

The NCP605/NCP606 regulator is self*protected with

internal thermal shutdown and internal current limit. Typical

application circuits are shown in Figures 1 to 4.

Input Decoupling (Cin)

A ceramic or tantalum 1.0 mF capacitor is recommended

and should be connected close to the NCP605/NCP606

package. Higher capacitance and lower ESR will improve

the overall line transient response.

Output Decoupling (Cout)

The NCP605/NCP606 is a stable component and does not

require a minimum Equivalent Series Resistance (ESR) for

the output capacitor. The minimum output decoupling value

is 1.0 mF and can be augmented to fulfill stringent load

transient requirements. The regulator works with ceramic

chip capacitors as well as tantalum devices. Larger values

improve noise rejection and load regulation transient

response. Typical characteristics were measured with

Murata ceramic capacitors. GRM219R71E105K (1 mF,

25 V, X7R, 0805) and GRM21BR71A106K (10 mF, 10 V,

X7R, 0805).

No−Load Regulation Considerations

The NCP605/NCP606 adjustable regulator will operate

properly under conditions where the only load current is

through the resistor divider that sets the output voltage.

However, in the case where the NCP605/NCP606 is

configured to provide a 1.250 V output, there is no resistor

divider. If the part is enabled under no−load conditions,

leakage current through the pass transistor at junction

temperatures above 85°C can approach several microamps,

especially as junction temperature approaches 150°C. If this

leakage current is not directed into a load, the output voltage

will rise up to a level approximately 20 mV above nominal.

The NCP605/ NCP606 contains an overshoot clamp

circuit to improve transient response during a load current

step release. When output voltage exceeds the nominal by

approximately 20 mV, this circuit becomes active and

clamps the output from further voltage increase. Tying the

ENABLE pin to Vin (NCP606 only) will ensure that the part

is active whenever the supply voltage is present, thus

guaranteeing that the clamp circuit is active whenever

leakage current is present.

When the NCP606 adjustable regulator is disabled, the

overshoot clamp circuit becomes inactive and the pass

transistor leakage will charge any capacitance on Vout. If no

load is present, the output can charge up to within a few

millivolts of Vin. In most applications, the load will present

some impedance to Vout such that the output voltage will be

inherently clamped at a safe level. A minimum load of

10 mA is recommended.

Unlike LP8345, for NCP605/606 fixed voltage versions

there is no limitation for minimum load current.

Noise Decoupling

The NCP605/NCP606 is a low noise regulator and needs

no external noise reduction capacitor. Unlike other low noise

regulators which require an external capacitor and have slow

startup times, the NCP605/NCP606 operates without a noise

reduction capacitor, has a typical 8 ms turn−on time and

achieves a 50 mVrms overall noise level between 10 Hz and

100 kHz.

Enable Operation (NCP606 Only)

The enable pin will turn the regulator on or off. The

threshold limits are covered in the electrical characteristics

table in this data sheet. The turn−on/turn−off transient

voltage being supplied to the enable pin should exceed a

slew rate of 10 mV/ms to ensure correct operation. If the

enable function is not to be used then the pin should be

connected to Vin.

Output Voltage Adjust

The output voltage can be adjusted from 1 times (Figure

4) to 4 times (Figure 3) the typical 1.250 V regulation

voltage via the use of resistors between the output and the

ADJ input. The output voltage and resistors are chosen using

Equation 1 and Equation 2.

Vout +1.250ǒ1)

R2Ǔ)ǒIADJ R1Ǔ(eq. 1)

(eq. 2)

R2^

Vout

1.25 *1

Input bias current IADJ is typically less than 150 nA.

Choose R1 arbitrarily to minimize errors due to the bias

current and to minimize noise contribution to the output

voltage. Use Equation 2 to find the required value for R2.

Thermal

As power in the NCP605/NCP606 increases, it might

become necessary to provide some thermal relief. The

maximum power dissipation supported by the device is

dependent upon board design and layout. Mounting pad

configuration on the PCB, the board material, and the

ambient temperature affect the rate of junction temperature

rise for the part. When the NCP605/NCP606 has good

thermal conductivity through the PCB, the junction

temperature will be relatively low with high power

applications. The maximum dissipation the

NCP605/NCP606 can handle is given by:

PD(MAX) +

ƪTJ(MAX) *TAƫ

RQJA

(eq. 3)

Since TJ is not recommended to exceed 125°C (TJ(MAX)),

then the NCP605/NCP606 soldered on 645 mm2, 1 oz

copper area, FR4 can dissipate up to 1.3 W when the ambient

NCP605, NCP606

http://onsemi.com

temperature (TA) is 25°C. See Figure 23 for RqJA versus

PCB area.

The power dissipated by the NCP605/NCP606 can be

calculated from the following equations:

PD[VinǒIGND@IOUTǓ)IoutǒVin *VoutǓ(eq. 4)

Vin(MAX) [

PD(MAX) )ǒVout IoutǓ

Iout )IGND

(eq. 5)

100

150

200

250

0 200 400 600 800

Figure 23. Thermal Resistance vs. Copper Area

COPPER AREA (mm2)

RqJA, (°C/W)

FR4 = 1.0 oz

FR4 = 2.0 oz

Hints

Vin and GND printed circuit board traces should be as

wide as possible. When the impedance of these traces is

high, there is a chance to pick up noise or cause the regulator

to malfunction. Place external components, especially the

output capacitor, as close as possible to the

NCP605/NCP606, and make traces as short as possible.

NCP605, NCP606

http://onsemi.com

ORDERING INFORMATION

Device

Nominal Output

Voltage (V) Marking Package Shipping†

NCP605MNADJT2G ADJ P605

ADJ

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP605MN15T2G 1.5 P605

150

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP605MN18T2G 1.8 P605

180

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP605MN25T2G 2.5 P605

250

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP605MN28T2G 2.8 P605

280

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP605MN30T2G 3.0 P605

300

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP605MN33T2G 3.3 P605

330

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP605MN50T2G 5.0 P605

500

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP606MNADJT2G ADJ P606

ADJ

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP606MN15T2G 1.5 P606

150

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP606MN18T2G 1.8 P606

180

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP606MN25T2G 2.5 P606

250

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP606MN28T2G 2.8 P606

280

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP606MN30T2G 3.0 P606

300

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP606MN33T2G 3.3 P606

330

DFN6

(Pb−Free)

3000 / Tape & Reel

NCP606MN50T2G 5.0 P606

500

DFN6

(Pb−Free)

3000 / Tape & Reel

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging

Specifications Brochure, BRD8011/D.

NCP605, NCP606

http://onsemi.com

PACKAGE DIMENSIONS

DFN6 3x3.3 MM, 0.95 PITCH

CASE 506AX−01

ISSUE O

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

SOLDERING FOOTPRINT*

ÇÇÇ

PIN 1

REFERENCE

C0.15

TOP VIEW

C0.15

NOTES:

1. DIMENSIONS AND TOLERANCING PER ASME

Y14.5M, 1994.

2. CONTROLLING DIMENSION: MILLIMETERS.

3. DIMENSION b APPLIES TO PLATED TERMINAL

AND IS MEASURED BETWEEN 0.25 AND 0.30 mm

FROM TERMINAL.

4. COPLANARITY APPLIES TO THE EXPOSED PAD

AS WELL AS THE TERMINALS.

BOTTOM VIEW

0.10

0.05

CAB

L1 64

(A3) C

C0.08

C0.10

SIDE VIEW A1

SEATING

PLANE

DIM MIN NOM MAX

MILLIMETERS

A0.80 −−− 0.90

A1 0.00 −−− 0.05

A3 0.20 REF

b0.30 −−− 0.40

D3.00 BSC

D2 1.90 −−− 2.10

E3.30 BSC

E2 1.10 −−− 1.30

e0.95 BSC

K0.20 −−− −−−

L0.40 −−− 0.60

(NOTE 3)

L1 0.00 −−− 0.15

0.83

2.15

1.35

0.50

0.95

PITCH

3.60

DIMENSIONS: MILLIMETERS

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,

copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC

reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any

particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without

limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications

and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC

does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for

surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where

personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and

its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,

any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture

of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

N. American Technical Support: 800−282−9855 Toll Free

USA/Canada

Europe, Middle East and Africa Technical Support:

Phone: 421 33 790 2910

Japan Customer Focus Center

Phone: 81−3−5817−1050

NCP605/D

LITERATURE FULFILLMENT:

Literature Distribution Center for ON Semiconductor

P.O. Box 5163, Denver, Colorado 80217 USA

Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada

Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

ON Semiconductor Website: www.onsemi.com

Order Literature: http://www.onsemi.com/orderlit

For additional information, please contact your local

Sales Representative