M48T35 M48T35Y 5 V, 256 Kbit (32 Kb x 8) TIMEKEEPER(R) SRAM Features Integrated, ultra low power SRAM, real-time clock, power-fail control circuit and battery BYTEWIDETM RAM-like clock access BCD coded year, month, day, date, hours, minutes, and seconds Frequency test output for real-time clock Automatic power-fail chip deselect and WRITE protection WRITE protect voltages VPFD = power-fail deselect voltage): - M48T35: VCC = 4.75 to 5.5 V; 4.5 V VPFD 4.75 V - M48T35Y: VCC = 4.5 to 5.5 V; 4.2 V VPFD 4.5 V Self-contained battery and crystal in the CAPHATTM DIP package SOIC package provides direct connection for a SNAPHAT(R) housing containing the battery and crystal SNAPHAT(R) housing (battery and crystal) is replaceable 1 PCDIP28 Battery/crystal CAPHATTM SNAPHAT(R) Battery/crystal 28 Pin and function compatible with JEDEC standard 32 Kb x 8 SRAMs 28 1 SOH28 RoHS compliant - Lead-free second level interconnect June 2011 Doc ID 2611 Rev 10 1/28 www.st.com 1 Contents M48T35, M48T35Y Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Operation modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3 2.1 READ mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.2 WRITE mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.3 Data retention mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Clock operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.1 Reading the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.2 Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.3 Stopping and starting the oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.4 Calibrating the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.5 Century bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.6 VCC noise and negative going transients . . . . . . . . . . . . . . . . . . . . . . . . . 16 4 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 7 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 8 Environmental information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2/28 Doc ID 2611 Rev 10 M48T35, M48T35Y List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 READ mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 WRITE mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Operating and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 DC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Power down/up AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Power down/up trip points DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 PCDIP28 - 28-pin plastic DIP, battery CAPHATTM, package mech. data . . . . . . . . . . . . . 21 SOH28 - 28-lead plastic SO, 4-socket battery SNAPHAT(R), package mechanical data . . 22 SH - 4-pin SNAPHAT(R) housing for 48 mAh battery & crystal, package mechanical data . 23 SH - 4-pin SNAPHAT(R) housing for 120 mAh battery & crystal, package mechanical data 24 Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 SNAPHAT(R) battery table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Doc ID 2611 Rev 10 3/28 List of figures M48T35, M48T35Y List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. 4/28 Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 DIP connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 SOIC connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 READ mode AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 WRITE enable controlled, WRITE AC waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Chip enable controlled, WRITE AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Crystal accuracy across temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Clock calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Supply voltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 AC measurement load circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Power down/up mode AC waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 PCDIP28 - 28-pin plastic DIP, battery CAPHATTM, package outline . . . . . . . . . . . . . . . . . 21 SOH28 - 28-lead plastic small outline, 4-socket battery SNAPHAT(R), package outline . . . 22 SH - 4-pin SNAPHAT(R) housing for 48 mAh battery & crystal, package outline. . . . . . . . . 23 SH - 4-pin SNAPHAT(R) housing for 120 mAh battery & crystal, package outline. . . . . . . . 24 Recycling symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Doc ID 2611 Rev 10 M48T35, M48T35Y 1 Description Description The M48T35/Y TIMEKEEPER(R) RAM is a 32 Kb x 8 non-volatile static RAM and real-time clock. The monolithic chip is available in two special packages to provide a highly integrated battery-backed memory and real-time clock solution. The M48T35/Y is a non-volatile pin and function equivalent to any JEDEC standard 32 Kb x 8 SRAM. It also easily fits into many ROM, EPROM, and EEPROM sockets, providing the non-volatility of PROMs without any requirement for special WRITE timing or limitations on the number of WRITEs that can be performed. The 28-pin, 600 mil DIP CAPHATTM houses the M48T35/Y silicon with a quartz crystal and a long life lithium button cell in a single package. The 28-pin, 330 mil SOIC provides sockets with gold plated contacts at both ends for direct connection to a separate SNAPHAT(R) housing containing the battery and crystal. The unique design allows the SNAPHAT battery package to be mounted on top of the SOIC package after the completion of the surface mount process. Insertion of the SNAPHAT housing after reflow prevents potential battery and crystal damage due to the high temperatures required for device surface-mounting. The SNAPHAT housing is keyed to prevent reverse insertion. The SOIC and battery/crystal packages are shipped separately in plastic anti-static tubes or in tape & reel form. For the 28-lead SOIC, the battery/crystal package (e.g., SNAPHAT) part number is "M4T28BR12SH". Figure 1. Logic diagram VCC 15 8 A0-A14 W DQ0-DQ7 M48T35 M48T35Y E G VSS Doc ID 2611 Rev 10 AI01620B 5/28 Description M48T35, M48T35Y Table 1. Signal names A0-A14 Address inputs DQ0-DQ7 Data inputs / outputs E Chip enable G Output enable W WRITE enable VCC Supply voltage VSS Ground Figure 2. DIP connections A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 VSS Figure 3. 28 1 27 2 26 3 4 25 24 5 23 6 7 M48T35 22 8 M48T35Y 21 20 9 19 10 11 18 12 17 13 16 14 15 VCC W A13 A8 A9 A11 G A10 E DQ7 DQ6 DQ5 DQ4 DQ3 AI01621B SOIC connections A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 VSS 1 28 27 2 26 3 25 4 24 5 23 6 22 7 M48T35Y 21 8 20 9 19 10 18 11 17 12 16 13 15 14 VCC W A13 A8 A9 A11 G A10 E DQ7 DQ6 DQ5 DQ4 DQ3 AI01622B 6/28 Doc ID 2611 Rev 10 M48T35, M48T35Y Figure 4. Description Block diagram OSCILLATOR AND CLOCK CHAIN 8 x 8 BiPORT SRAM ARRAY 32,768 Hz CRYSTAL A0-A14 POWER 32,760 x 8 SRAM ARRAY LITHIUM CELL DQ0-DQ7 E VOLTAGE SENSE AND SWITCHING CIRCUITRY W VPFD VCC G VSS Doc ID 2611 Rev 10 AI01623 7/28 Operation modes 2 M48T35, M48T35Y Operation modes As Figure 4 on page 7 shows, the static memory array and the quartz controlled clock oscillator of the M48T35/Y are integrated on one silicon chip. The two circuits are interconnected at the upper eight memory locations to provide user accessible BYTEWIDE clock information in the bytes with addresses 7FF8h-7FFFh. The clock locations contain the year, month, date, day, hour, minute, and second in 24-hour BCD format. Corrections for 28, 29 (leap year - valid until 2100), 30, and 31 day months are made automatically. Byte 7FF8h is the clock control register. This byte controls user access to the clock information and also stores the clock calibration setting. The eight clock bytes are not the actual clock counters themselves; they are memory locations consisting of BiPORTTM READ/WRITE memory cells. The M48T35/Y includes a clock control circuit which updates the clock bytes with current information once per second. The information can be accessed by the user in the same manner as any other location in the static memory array. The M48T35/Y also has its own power-fail detect circuit. The control circuitry constantly monitors the single 5 V supply for an out of tolerance condition. When VCC is out of tolerance, the circuit write protects the SRAM, providing a high degree of data security in the midst of unpredictable system operation brought on by low VCC. As VCC falls below the battery backup switchover voltage (VSO), the control circuitry connects the battery which maintains data and clock operation until valid power returns. Table 2. Operating modes Mode VCC Deselect WRITE READ 4.75 to 5.5 V or 4.5 to 5.5 V READ Deselect Deselect VSO to VPFD VSO (min)(1) (1) E G W DQ0-DQ7 Power VIH X X High Z Standby VIL X VIL DIN Active VIL VIL VIH DOUT Active VIL VIH VIH High Z Active X X X High Z CMOS standby X X X High Z Battery backup mode 1. See Table 11 on page 20 for details. X = VIH or VIL; VSO = battery backup switchover voltage. 2.1 READ mode The M48T35/Y is in the READ mode whenever W (WRITE enable) is high and E (chip enable) is low. The unique address specified by the 15 address inputs defines which one of the 32,768 bytes of data is to be accessed. Valid data will be available at the data I/O pins within address access time (tAVQV) after the last address input signal is stable, providing that the E and G access times are also satisfied. If the E and G access times are not met, valid data will be available after the latter of the chip enable access time (tELQV) or output enable access time (tGLQV). The state of the eight three-state data I/O signals is controlled by E and G. If the outputs are activated before tAVQV, the data lines will be driven to an indeterminate state until tAVQV. 8/28 Doc ID 2611 Rev 10 M48T35, M48T35Y Operation modes If the address inputs are changed while E and G remain active, output data will remain valid for output data hold time (tAXQX) but will go indeterminate until the next address access. Figure 5. READ mode AC waveforms tAVAV VALID A0-A14 tAVQV tAXQX tELQV tEHQZ E tELQX tGLQV tGHQZ G tGLQX DQ0-DQ7 VALID AI00925 Note: WRITE enable (W) = high. Table 3. READ mode AC characteristics M48T35/Y Parameter(1) Symbol Unit Min Max tAVAV READ cycle time tAVQV Address valid to output valid 70 ns tELQV Chip enable low to output valid 70 ns tGLQV Output enable low to output valid 35 ns tELQX(2) tGLQX(2) tEHQZ(2) tGHQZ(2) tAXQX 70 Chip enable low to output transition 5 Output enable low to output transition 5 ns ns ns Chip enable high to output Hi-Z 25 ns Output enable high to output Hi-Z 25 ns Address transition to output transition 10 ns 1. Valid for ambient operating temperature: TA = 0 to 70 or -40 to 85 C; VCC = 4.75 to 5.5 V or 4.5 to 5.5 V (except where noted). 2. CL = 5 pF. Doc ID 2611 Rev 10 9/28 Operation modes 2.2 M48T35, M48T35Y WRITE mode The M48T35/Y is in the WRITE mode whenever W and E are low. The start of a WRITE is referenced from the latter occurring falling edge of W or E. A WRITE is terminated by the earlier rising edge of W or E. The addresses must be held valid throughout the cycle. E or W must return high for a minimum of tEHAX from chip enable or tWHAX from WRITE enable prior to the initiation of another READ or WRITE cycle. Data-in must be valid tDVWH prior to the end of WRITE and remain valid for tWHDX afterward. G should be kept high during WRITE cycles to avoid bus contention; although, if the output bus has been activated by a low on E and G, a low on W will disable the outputs tWLQZ after W falls. Figure 6. WRITE enable controlled, WRITE AC waveform tAVAV VALID A0-A14 tAVWH tAVEL tWHAX E tWLWH tAVWL W tWLQZ tWHQX tWHDX DQ0-DQ7 DATA INPUT tDVWH Figure 7. AI00926 Chip enable controlled, WRITE AC waveforms tAVAV A0-A14 VALID tAVEH tAVEL tELEH tEHAX E tAVWL W tEHDX DQ0-DQ7 DATA INPUT tDVEH 10/28 Doc ID 2611 Rev 10 AI00927 M48T35, M48T35Y Table 4. Symbol Operation modes WRITE mode AC characteristics M48T35/Y Parameter(1) Unit Min Max tAVAV WRITE cycle time 70 tAVWL Address valid to WRITE enable low 0 ns tAVEL Address valid to chip enable low 0 ns tWLWH WRITE enable pulse width 50 ns tELEH Chip enable low to chip enable high 55 ns tWHAX WRITE enable high to address transition 0 ns tEHAX Chip enable high to address transition 0 ns tDVWH Input valid to WRITE enable high 30 ns tDVEH Input valid to chip enable high 30 ns tWHDX WRITE enable high to input transition 5 ns tEHDX Chip enable high to input transition 5 ns tWLQZ(2)(3) WRITE enable low to output Hi-Z ns 25 ns tAVWH Address valid to WRITE enable high 60 tAVEH Address valid to chip enable high 60 ns 5 ns tWHQX(2)(3) WRITE enable high to output transition ns 1. Valid for ambient operating temperature: TA = 0 to 70 or -40 to 85 C; VCC = 4.75 to 5.5 V or 4.5 to 5.5 V (except where noted). 2. CL = 5 pF. 3. If E goes low simultaneously with W going low, the outputs remain in the high impedance state. 2.3 Data retention mode With valid VCC applied, the M48T35/Y operates as a conventional BYTEWIDE static RAM. Should the supply voltage decay, the RAM will automatically power-fail deselect, write protecting itself when VCC falls within the VPFD (max), VPFD (min) window. All outputs become high impedance, and all inputs are treated as "Don't care" (see Figure 12 on page 19, Table 10, and Table 11 on page 20). Note: A power failure during a WRITE cycle may corrupt data at the currently addressed location, but does not jeopardize the rest of the RAM's content. At voltages below VPFD (min), the user can be assured the memory will be in a write protected state, provided the VCC fall time is not less than tF. The M48T35/Y may respond to transient noise spikes on VCC that reach into the deselect window during the time the device is sampling VCC. Therefore, decoupling of the power supply lines is recommended. When VCC drops below VSO, the control circuit switches power to the internal battery which preserves data and powers the clock. The internal button cell will maintain data in the M48T35/Y for an accumulated period of at least 7 years when VCC is less than VSO. As system power returns and VCC rises above VSO, the battery is disconnected, and the power supply is switched to external VCC. Write protection continues until VCC reaches VPFD (min) plus trec (min). E should be kept high as VCC rises past VPFD (min) to prevent inadvertent WRITE cycles prior to processor stabilization. Normal RAM operation can resume trec after VCC exceeds VPFD (max). For more information on battery storage life refer to the application note AN1012. Doc ID 2611 Rev 10 11/28 Clock operations 3 Clock operations 3.1 Reading the clock M48T35, M48T35Y Updates to the TIMEKEEPER(R) registers (see Table 5) should be halted before clock data is read to prevent reading data in transition. The BiPORTTM TIMEKEEPER cells in the RAM array are only data registers and not the actual clock counters, so updating the registers can be halted without disturbing the clock itself. Updating is halted when a '1' is written to the READ bit, D6 in the control register 7FF8h. As long as a '1' remains in that position, updating is halted. After a halt is issued, the registers reflect the count; that is, the day, date, and the time that were current at the moment the halt command was issued. All of the TIMEKEEPER registers are updated simultaneously. A halt will not interrupt an update in progress. Updating is within a second after the bit is reset to a '0.' 3.2 Setting the clock Bit D7 of the control register 7FF8h is the WRITE bit. Setting the WRITE bit to a '1,' like the READ bit, halts updates to the TIMEKEEPER(R) registers. The user can then load them with the correct day, date, and time data in 24-hour BCD format (see Table 5). Resetting the WRITE bit to a '0' then transfers the values of all time registers 7FF9h-7FFFh to the actual TIMEKEEPER counters and allows normal operation to resume. The FT bit and the bits marked as '0' in Table 5 must be written to '0' to allow for normal TIMEKEEPER and RAM operation. After the WRITE bit is reset, the next clock update will occur within one second. See the application note AN923, "TIMEKEEPER(R) Rolling Into the 21st Century" for information on century rollover. 3.3 Stopping and starting the oscillator The oscillator may be stopped at any time. If the device is going to spend a significant amount of time on the shelf, the oscillator can be turned off to minimize current drain on the battery. The STOP bit is the MSB of the seconds register. Setting it to a '1' stops the oscillator. The M48T35/Y is shipped from STMicroelectronics with the STOP bit set to a '1.' When reset to a '0,' the M48T35/Y oscillator starts within 1 second. 12/28 Doc ID 2611 Rev 10 M48T35, M48T35Y Table 5. Clock operations Register map Data Function/range Address D7 D6 7FFEh 0 0 7FFDh 0 0 7FFCh 0 FT 7FFBh 0 0 7FFAh 0 7FF9h ST 7FF8h W 7FFFh D5 D4 D3 D2 10 Years 0 Year 00-99 Month 01-12 Date Date 01-31 Century/ day 00-01/01-07 Hours Hours 00-23 Minutes Minutes 00-59 Seconds Seconds 00-59 0 Day 10 hours 10 minutes 10 seconds R S BCD format Year 10 date CB D0 Month 10 M. CEB D1 Calibration Control Keys: S = SIGN bit FT = FREQUENCY TEST bit (must be set to '0' upon power for normal operation) R = READ bit W = WRITE bit ST = STOP bit 0 = Must be set to '0' CEB = CENTURY ENABLE bit CB = CENTURY bit Note: When CEB is set to '1,' CB will toggle from '0' to '1' or from '1' to '0' at the turn of the century (dependent upon the initial value set). When CEB is set to '0,' CB will not toggle. The WRITE bit does not need to be set to write to CEB. 3.4 Calibrating the clock The M48T35/Y is driven by a quartz-controlled oscillator with a nominal frequency of 32,768 Hz. The devices are tested not to exceed 35 ppm (parts per million) oscillator frequency error at 25 C, which equates to about 1.53 minutes per month. With the calibration bits properly set, the accuracy of each M48T35/Y improves to better than +1/-2 ppm at 25 C. The oscillation rate of any crystal changes with temperature (see Figure 8 on page 15). Most clock chips compensate for crystal frequency and temperature shift error with cumbersome "trim" capacitors. The M48T35/Y design, however, employs periodic counter correction. The calibration circuit adds or subtracts counts from the oscillator divider circuit at the divide by 256 stage, as shown in Figure 9 on page 15. The number of times pulses are blanked (subtracted, negative calibration) or split (added, positive calibration) depends upon the value loaded into the five calibration bits found in the control register. Adding counts speeds the clock up, subtracting counts slows the clock down. The calibration byte occupies the five lower order bits (D4-D0) in the control register 7FF8h. These bits can be set to represent any value between 0 and 31 in binary form. Bit D5 is the Doc ID 2611 Rev 10 13/28 Clock operations M48T35, M48T35Y sign bit; '1' indicates positive calibration, '0' indicates negative calibration. Calibration occurs within a 64 minute cycle. The first 62 minutes in the cycle may, once per minute, have one second either shortened by 128 or lengthened by 256 oscillator cycles. If a binary '1' is loaded into the register, only the first 2 minutes in the 64 minute cycle will be modified; if a binary 6 is loaded, the first 12 will be affected, and so on. Therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator cycles for every 125,829,120 actual oscillator cycles, that is +4.068 or -2.034 ppm of adjustment per calibration step in the calibration register. Assuming that the oscillator is in fact running at exactly 32,768 Hz, each of the 31 increments in the calibration byte would represent +10.7 or -5.35 seconds per month which corresponds to a total range of +5.5 or -2.75 minutes per month. Two methods are available for ascertaining how much calibration a given M48T35/Y may require. The first involves simply setting the clock, letting it run for a month and comparing it to a known accurate reference (like WWV broadcasts). While that may seem crude, it allows the designer to give the end user the ability to calibrate his clock as his environment may require, even after the final product is packaged in a non-user serviceable enclosure. All the designer has to do is provide a simple utility that accesses the calibration byte. The second approach is better suited to a manufacturing environment, and involves the use of some test equipment. When the frequency test (FT) bit, the seventh-most significant bit in the day register is set to a '1,' and D7 of the seconds register is a '0' (oscillator running), DQ0 will toggle at 512 Hz during a READ of the seconds register. Any deviation from 512 Hz indicates the degree and direction of oscillator frequency shift at the test temperature. For example, a reading of 512.01024 Hz would indicate a +20 ppm oscillator frequency error, requiring a -10 (WR001010) to be loaded into the calibration byte for correction. Note: Setting or changing the calibration byte does not affect the frequency test output frequency. The FT bit MUST be reset to '0' for normal clock operations to resume. The FT bit is automatically reset on power-down. For more information on calibration, see application note AN934, "TIMEKEEPER(R) Calibration." 3.5 Century bit Bit D5 and D4 of clock register 1FFCh contain the CENTURY ENABLE bit (CEB) and the CENTURY bit (CB). Setting CEB to a '1' will cause CB to toggle, either from a '0' to '1' or from '1' to '0' at the turn of the century (depending upon its initial state). If CEB is set to a '0,' CB will not toggle. Note: 14/28 The WRITE bit must be set in order to write to the CENTURY bit. Doc ID 2611 Rev 10 M48T35, M48T35Y Clock operations Figure 8. Crystal accuracy across temperature ppm 20 0 -20 -40 F = -0.038 ppm (T - T )2 10% 0 F C2 -60 T0 = 25 C -80 -100 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 C AI02124 Figure 9. Clock calibration NORMAL POSITIVE CALIBRATION NEGATIVE CALIBRATION AI00594B Doc ID 2611 Rev 10 15/28 Clock operations 3.6 M48T35, M48T35Y VCC noise and negative going transients ICC transients, including those produced by output switching, can produce voltage fluctuations, resulting in spikes on the VCC bus. These transients can be reduced if capacitors are used to store energy which stabilizes the VCC bus. The energy stored in the bypass capacitors will be released as low going spikes are generated or energy will be absorbed when overshoots occur. A bypass capacitor value of 0.1 F (as shown in Figure 10) is recommended in order to provide the needed filtering. In addition to transients that are caused by normal SRAM operation, power cycling can generate negative voltage spikes on VCC that drive it to values below VSS by as much as one volt. These negative spikes can cause data corruption in the SRAM while in battery backup mode. To protect from these voltage spikes, it is recommended to connect a Schottky diode from VCC to VSS (cathode connected to VCC, anode to VSS). Schottky diode 1N5817 is recommended for through hole and MBRS120T3 is recommended for surface mount. Figure 10. Supply voltage protection VCC VCC 0.1F DEVICE VSS AI02169 16/28 Doc ID 2611 Rev 10 M48T35, M48T35Y 4 Maximum ratings Maximum ratings Stressing the device above the rating listed in the absolute maximum ratings table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 6. Absolute maximum ratings Symbol TA TSTG TSLD (1)(2)(3) Parameter Ambient operating temperature Value Unit Grade 1 0 to 70 C Grade 6 -40 to 85 C -40 to 85 C 260 C Storage temperature (VCC off, oscillator off) Lead solder temperature for 10 seconds M48T35 -0.3 to 7 V M48T35Y -0.3 to 7 V M48T35 -0.3 to 7 V M48T35Y -0.3 to 7 V Output current 20 mA Power dissipation 1 W VIO Input or output voltages VCC Supply voltage IO PD 1. For DIP package, soldering temperature of the IC leads is to not exceed 260 C for 10 seconds. Furthermore, the devices shall not be exposed to IR reflow nor preheat cycles (as performed as part of wave soldering). ST recommends the devices be hand-soldered or placed in sockets to avoid heat damage to the batteries. 2. For DIP packaged devices, ultrasonic vibrations should not be used for post-solder cleaning to avoid damaging the crystal. 3. For SOH28 package, lead-free (Pb-free) lead finish: reflow at peak temperature of 260 C (the time above 255 C must not exceed 30 seconds). Caution: Negative undershoots below -0.3 V are not allowed on any pin while in the battery backup mode. Caution: Do NOT wave solder SOIC to avoid damaging SNAPHAT(R) sockets. Doc ID 2611 Rev 10 17/28 DC and AC parameters 5 M48T35, M48T35Y DC and AC parameters This section summarizes the operating and measurement conditions, as well as the DC and AC characteristics of the device. The parameters in the following DC and AC characteristic tables are derived from tests performed under the measurement conditions listed in the relevant tables. Designers should check that the operating conditions in their projects match the measurement conditions when using the quoted parameters. Table 7. Operating and AC measurement conditions Parameter Supply voltage (VCC) M48T35 M48T35Y Unit 4.75 to 5.5 4.5 to 5.5 V 0 to 70 -40 to 85 C Load capacitance (CL) Ambient operating temperature (TA) 100 100 pF Input rise and fall times 5 5 ns 0 to 3 0 to 3 V 1.5 1.5 V Input pulse voltages Input and output timing ref. voltages Note: Output Hi-Z is defined as the point where data is no longer driven. Figure 11. AC measurement load circuit 5V 1.9k DEVICE UNDER TEST OUT 1k CL = 100pF or 5pF CL includes JIG capacitance Table 8. AI01030 Capacitance Symbol Parameter(1)(2) Min Max Unit CIN Input capacitance - 10 pF COUT(3) Output capacitance - 10 pF 1. Effective capacitance measured with power supply at 5 V; sampled only, not 100% tested. 2. At 25 C, f = 1 MHz. 3. Outputs deselected. 18/28 Doc ID 2611 Rev 10 M48T35, M48T35Y DC and AC parameters Table 9. DC characteristics Symbol Parameter M48T35 Test condition(1) M48T35Y Unit Min Max Min Max ILI Input leakage current 0 V VIN VCC 1 1 A ILO(2) Output leakage current 0 V VOUT VCC 1 1 A ICC Supply current Outputs open 50 30 mA ICC1 Supply current (standby) TTL E = VIH 3 3 mA ICC2 Supply current (standby) CMOS E = VCC - 0.2 V 2 2 mA VIL Input low voltage -0.3 0.8 -0.3 0.8 V VIH Input high voltage 2.2 VCC + 0.3 2.2 VCC + 0.3 V VOL Output low voltage IOL = 2.1 mA 0.4 V VOH Output high voltage IOH = -1 mA 0.4 2.4 2.4 V 1. Valid for ambient operating temperature: TA = 0 to 70 or -40 to 85 C; VCC = 4.75 to 5.5 V or 4.5 to 5.5 V (except where noted). 2. Outputs deselected. Figure 12. Power down/up mode AC waveforms VCC VPFD (max) VPFD (min) VSO tF tR tFB tDR tPD INPUTS tRB RECOGNIZED trec DON'T CARE RECOGNIZED HIGH-Z OUTPUTS VALID VALID (PER CONTROL INPUT) (PER CONTROL INPUT) AI01168C Doc ID 2611 Rev 10 19/28 DC and AC parameters Table 10. M48T35, M48T35Y Power down/up AC characteristics Parameter(1) Symbol tPD tF (2) tFB(3) Min E or W at VIH before power down VPFD (max) to VPFD (min) VCC fall time VPFD (min) to VSS VCC fall time Max Unit 0 s 300 s M48T35 10 s M48T35Y 10 s tR VPFD (min) to VPFD (max) VCC rise time 10 s tRB VSS to VPFD (min) VCC rise time 1 s trec(4) VPFD (max) to inputs recognized 40 200 ms 1. Valid for ambient operating temperature: TA = 0 to 70 or -40 to 85 C; VCC = 4.75 to 5.5 V or 4.5 to 5.5 V (except where noted). 2. VPFD (max) to VPFD (min) fall time of less than tF may result in deselection/write protection not occurring until 200 s after VCC passes VPFD (min). 3. VPFD (min) to VSS fall time of less than tFB may cause corruption of RAM data. 4. trec (min) = 20 ms for industrial temperature grade 6 device. Table 11. Power down/up trip points DC characteristics Parameter(1)(2) Symbol VPFD VSO tDR(3)(5) Power-fail deselect voltage Battery backup switchover voltage Expected data retention time Min Typ Max Unit M48T35 4.5 4.6 4.75 V M48T35Y 4.2 4.35 4.5 V M48T35 M48T35Y 3.0 V 3.0 V Grade 1 10(4) Years Grade 6 (5) Years 10 1. Valid for ambient operating temperature: TA = 0 to 70 or -40 to 85 C; VCC = 4.75 to 5.5 V or 4.5 to 5.5 V (except where noted). 2. All voltages referenced to VSS. 3. CAPHATTM and M4T32-BR12SH1 SNAPHAT(R) only, M4T28-BR12SH1 SNAPHAT(R) top tDR = 7 years (typ). 4. Using larger M4T32-BR12SH6 SNAPHAT(R) top (recommended for industrial temperature range - grade 6 device). 5. At 25 C, VCC = 0 V. 20/28 Doc ID 2611 Rev 10 M48T35, M48T35Y 6 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Figure 13. PCDIP28 - 28-pin plastic DIP, battery CAPHATTM, package outline A2 A1 B1 B A L C e1 eA e3 D N E 1 PCDIP Note: Drawing is not to scale. Table 12. PCDIP28 - 28-pin plastic DIP, battery CAPHATTM, package mech. data mm inches Symbol Typ Min Max A 8.89 A1 Min Max 9.65 0.350 0.380 0.38 0.76 0.015 0.030 A2 8.38 8.89 0.330 0.350 B 0.38 0.53 0.015 0.021 B1 1.14 1.78 0.045 0.070 C 0.20 0.31 0.008 0.012 D 39.37 39.88 1.550 1.570 E 17.83 18.34 0.702 0.722 e1 2.29 2.79 0.090 0.110 e3 33.02 Typ 1.3 eA 15.24 16.00 0.600 0.630 L 3.05 3.81 0.120 0.150 N 28 Doc ID 2611 Rev 10 28 21/28 Package mechanical data M48T35, M48T35Y Figure 14. SOH28 - 28-lead plastic small outline, 4-socket battery SNAPHAT(R), package outline A2 A C B eB e CP D N E H A1 L 1 Note: SOH-A Drawing is not to scale. Table 13. SOH28 - 28-lead plastic SO, 4-socket battery SNAPHAT(R), package mechanical data mm inches Symbol Typ Min A Typ Min 3.05 Max 0.120 A1 0.05 0.36 0.002 0.014 A2 2.34 2.69 0.092 0.106 B 0.36 0.51 0.014 0.020 C 0.15 0.32 0.006 0.012 D 17.71 18.49 0.697 0.728 E 8.23 8.89 0.324 0.350 e - - - - eB 3.20 3.61 0.126 0.142 H 11.51 12.70 0.453 0.500 L 0.41 1.27 0.016 0.050 a 0 8 0 8 N 28 CP 22/28 Max 1.27 0.050 28 0.10 Doc ID 2611 Rev 10 0.004 M48T35, M48T35Y Package mechanical data Figure 15. SH - 4-pin SNAPHAT(R) housing for 48 mAh battery & crystal, package outline A1 A2 A3 A eA B L eB D E SHTK Note: Drawing is not to scale. Table 14. SH - 4-pin SNAPHAT(R) housing for 48 mAh battery & crystal, package mechanical data mm inches Symbol Typ Min A Max Typ Min 9.78 Max 0.385 A1 6.73 7.24 0.265 0.285 A2 6.48 6.99 0.255 0.275 B 0.46 0.56 0.018 0.022 D 21.21 21.84 0.835 0.860 E 14.22 14.99 0.560 0.590 eB 3.20 3.61 0.126 0.142 L 2.03 2.29 0.080 0.090 A3 0.38 Doc ID 2611 Rev 10 0.015 23/28 Package mechanical data M48T35, M48T35Y Figure 16. SH - 4-pin SNAPHAT(R) housing for 120 mAh battery & crystal, package outline A1 A2 A3 A eA B L eB D E SHTK Note: Drawing is not to scale. Table 15. SH - 4-pin SNAPHAT(R) housing for 120 mAh battery & crystal, package mechanical data mm inches Symbol Typ Min A Typ Min 10.54 Max 0.415 A1 8.00 8.51 0.315 0.335 A2 7.24 8.00 0.285 0.315 B 0.46 0.56 0.018 0.022 D 21.21 21.84 0.835 0.860 E 17.27 18.03 0.680 0.710 eB 3.20 3.61 0.126 0.142 L 2.03 2.29 0.080 0.090 A3 24/28 Max 0.38 Doc ID 2611 Rev 10 0.015 M48T35, M48T35Y 7 Part numbering Part numbering Table 16. Ordering information scheme Example: M48T 35 -70 PC 1 E Device type M48T Supply voltage and write protect voltage 35(1) = VCC = 4.75 to 5.5 V; VPFD = 4.5 to 4.75 V 35Y(2) = VCC = 4.5 to 5.5 V; VPFD = 4.2 to 4.5 V Speed -70 = 70 ns Package PC = PCDIP28 MH(3) = SOH28 Temperature range 1 = 0 to 70 C 6(4) = -40 to 85 C Shipping method For SOH28: E = ECOPACK(R) package, tubes F = ECOPACK(R) package, tape & reel For PCDIP28: blank = ECOPACK(R) package, tubes 1. The M48T35 part is offered only in the PCDIP28 (i.e. CAPHATTM) package. 2. The M48T35Y is available only in the SOH28 (i.e. SNAPHAT SOIC) package. 3. The SOIC package (SOH28) requires the SNAPHAT(R) battery package which is ordered separately under the part number "M4TXX-BR12SH" (see Table 17 on page 25). 4. Temperature grade 6 (-40 to +85 C) devices are not for new design. Contact ST sales office for availability. Caution: Do not place the SNAPHAT battery package "M4TXX-BR12SH" in conductive foam as it will drain the lithium button-cell battery. For other options, or for more information on any aspect of this device, please contact the ST sales office nearest you. Table 17. SNAPHAT(R) battery table Part number M4T28-BR12SH M4T32-BR12SH Description Lithium battery (48 mAh) SNAPHAT(R) Lithium battery (120 mAh) SNAPHAT(R) Doc ID 2611 Rev 10 Package SH SH 25/28 Environmental information 8 M48T35, M48T35Y Environmental information Figure 17. Recycling symbols This product contains a non-rechargeable lithium (lithium carbon monofluoride chemistry) button cell battery fully encapsulated in the final product. Recycle or dispose of batteries in accordance with the battery manufacturer's instructions and local/national disposal and recycling regulations. 26/28 Doc ID 2611 Rev 10 M48T35, M48T35Y 9 Revision history Revision history Table 18. Document revision history Date Revision Nov-1999 1 07-Feb-2000 1.1 Changes First issue tDR description changed (Table 9) Reformatted; temp/voltage info. added to tables (Table 8, 9, 3, 4, 10, 11); add century bit text 04-Jun-2001 2 31-Jul-2001 2.1 Formatting changes based on latest document reviews 06-Mar-2002 2.2 Add PMDIP packaging option, which is "Not for New Design" (NND) (Table 16) 20-May-2002 2.3 Modify reflow time and temperature footnotes (Table 6) 26-Jun-2002 2.4 Add footnote to table (Table 11) 31-Mar-2003 3 v2.2 template applied; data retention condition updated (Table 11) 10-Dec-2003 4 Reformatted; update DC characteristics (Table 9) 31-Mar-2004 5 Reformatted; update Pb-free package information (Table 6, 16) 05-Dec-2005 6 Updated template, lead-free text, and remove footnote (Table 9, 16) 01-Aug-2007 7 Reformatted; added lead-free second level interconnect information to cover page and Section 6: Package mechanical data. 12-Feb-2009 8 Updated Table 6; text in Section 6: Package mechanical data; added Section 8: Environmental information; minor formatting changes. 08-Sep-2010 9 Reformatted document; updated Section 4, Table 12, 16; removed PMDIP28 package. 07-Jun-2011 10 Updated footnote 1 of Table 6: Absolute maximum ratings; updated Section 8: Environmental information. Doc ID 2611 Rev 10 27/28 M48T35, M48T35Y Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2011 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 28/28 Doc ID 2611 Rev 10