HMC882LP5E v01.0310 FILTERS - TUNABLE - SMT 3 FILTER - TUNABLE, LOW PASS SMT 4.5 - 7.6 GHz Typical Applications Features The HMC882LP5E is ideal for: Fast Tuning Response; 150 ns * Test & Measurement Equipment Excellent Wideband Rejection; 40 dB * Military RADAR & EW/ECM Single Positive Frequency Control: 0 to +14V * SATCOM & Space Low Insertion Loss & User Selectable Cutoff Frequency * Industrial & Medical Equipment Single Chip Replacement for Mechanically Tuned Designs 32 Lead 5x5 mm SMT Package Functional Diagram General Description The HMC882LP5E is a MMIC low pass filter which features a user selectable cutoff frequency. The cutoff frequency can be varied from 4.5 to 7.6 GHz by applying a single analog tuning voltage between 0 and 14V. This low pass filter provides a low 2.9 dB insertion loss, 10 dB return loss and 1.23 x cutoff stopband attenuation of >20 dB. This tunable filter can be used as a much smaller alternative to physically large switched filter banks and cavity tuned filters. The HMC882LP5E has excellent microphonics due to the monolithic design, and provides a dynamically adjustable solution in advanced communications applications. The low pass tunable filter is packaged in a RoHS compliant 5x5mm QFN leadless package. Electrical Specifi cations, TA = +25C Parameter Passband Min. Typ. 0 cutoff [1] Tuning Range (3 dB Loss) 4.5 Max. Units 7.6 GHz 7.6 GHz Stopband Frequency (Rejection >20 dB) 1.23 x cutoff GHz Re-entry Frequency (Rejection <30 dB) 30 GHz Insertion Loss 2.9 dB Return Loss 10 Maximum Input Power for Linear Operation Frequency Control Voltage (Vfctl) 0 Frequency Control Port Source/Sink Current (Ifctl)a dB 10 dBm 14 V 1 Residual Phase Noise [2] (1 MHz offset) -160 cutoff Drift Rate (Fixed Vfctl) -1.4 mA dBc/Hz MHz/C [3] Tuning Characteristics tFULLBAND (0% Vfctl to 90% RF) 150 ns [1] cutoff defined as the point at which the insertion loss is 3 dB below the minimum passband insertion loss. [2] Optimum residual phase noise performance requires the use of a low noise driver circuit. [3]Tuning speed is dependent on driver circuit. Data measured with a high speed op-amp driver and includes driver slew rate delay. 3-8 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC882LP5E v01.0310 FILTER - TUNABLE, LOW PASS SMT 4.5 - 7.6 GHz Broadband Insertion Loss vs. Control Voltage 3 Broadband Return Loss vs. Control Voltage 0 0V 7V 7V -20 RETURN LOSS (dB) INSERTION LOSS (dB) -10 14V 0V -30 -40 -50 -10 14V -20 S11 S22 -30 -60 -70 -40 0 5 10 15 20 25 30 0 5 10 FREQUENCY (GHz) 15 20 25 30 FREQUENCY (GHz) Insertion Loss vs. Control Voltage [1] Return Loss vs. Control Voltage [1] 0 0 7V -3 RETURN LOSS (dB) INSERTION LOSS (dB) 0V 7V 14V 0V -6 -9 -10 FILTERS - TUNABLE - SMT 0 14V -20 -30 S11 S22 -12 -40 0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 5 6 7 8 9 10 Return Loss vs. Temperature, Vfctl @ 7V [1] 0 0 -3 -10 RETURN LOSS (dB) INSERTION LOSS (dB) Insertion Loss vs. Temperature, Vfctl @ 7V [1] -6 +25C +85C -40C -9 4 FREQUENCY (GHz) FREQUENCY (GHz) +25C +85C -40C S11 -20 -30 S22 -40 -12 0 1 2 3 4 5 6 7 8 0 1 FREQUENCY (GHz) 2 3 4 5 6 7 8 FREQUENCY (GHz) [1] Low frequency performance limited by external DC blocking capacitors at RF input and output. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 3-9 HMC882LP5E v01.0310 FILTER - TUNABLE, LOW PASS SMT 4.5 - 7.6 GHz 3 Average Insertion Loss vs. Temperature in a 2 dB Bandwidth Cutoff Frequency vs. Temperature 0 FREQUENCY(GHz) INSERTION LOSS(dB) +25C +85C -40C 8 7 6 5 +25C +85C -40C -1 -2 -3 -4 4 -5 0 2 4 6 8 10 12 14 0 2 4 6 Vfctl (V) 10 12 14 12 14 Maximum Return Loss in a 2 dB Bandwidth vs. Temperature [1] 1.5 0 +25C +85C -40C +25C +85C -40C -4 RETURN LOSS (dB) 1.4 1.3 1.2 1.1 -8 -12 -16 1 -20 0 2 4 6 8 10 12 14 0 2 4 6 Vtune(V) 8 10 Vfctl (V) Group Delay Tuning Sensitivity vs. Temperature 1 600 GROUP DELAY (nsec) +25C +85C -40C 500 SENSITIVITY(MHz/V) 8 Vfctl (V) Rejection Ratio vs. Temperature F20dB TO F3dB RATIO FILTERS - TUNABLE - SMT 9 400 300 200 0.8 0V 0.6 7V 14V 0.4 0.2 100 0 0 0 2 4 6 Vfctl (V) 8 10 12 14 1 2 3 4 5 6 7 8 9 FREQUENCY (GHz) [1] Rejection ratio is defined as the ratio of the frequency at which the relative insertion loss is 20 dB to cutoff 3 - 10 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC882LP5E v01.0310 FILTER - TUNABLE, LOW PASS SMT 4.5 - 7.6 GHz Frequency Control Voltage (Vfctl) -0.5 to +15V RF Power Input 26.5 dBm Storage Temperature -65 to +150 C ESD Rating (HBM) Class 1B 3 Reliability Information Junction Temperature to Maintain 1 Million Hour MTTF 150 C Nominal Junction Temperature (T= 85 C and Pin = 10 dBm) 90 C Operating Temperature -40 to +85 C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing FILTERS - TUNABLE - SMT Absolute Maximum Ratings NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. Pin BURR LENGTH SHALL BE 0.15mm MAXIMUM. Pin BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish HMC882LP5E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL Rating MSL1 [2] Package Marking [1] H882 XXXX [1] 4-Digit lot number XXXX [2] Max peak reflow temperature of 260 C For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 3 - 11 HMC882LP5E v01.0310 FILTER - TUNABLE, LOW PASS SMT 4.5 - 7.6 GHz FILTERS - TUNABLE - SMT 3 Pin Descriptions Pin Number Function Description 1 - 4, 7 - 13, 15 - 18, 21 - 32 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 5, 20 GND These pins and exposed paddle must be connected to RF/DC ground. 6 RFIN This pin is DC coupled and matched to 50 Ohms. External voltage must not be applied to this pin. 14 Vfctl Cutoff frequency control voltage. 19 RFOUT This pin is DC coupled and matched to 50 Ohms. External voltage must not be applied to this pin. Interface Schematic Application Circuit 3 - 12 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC882LP5E v01.0310 FILTER - TUNABLE, LOW PASS SMT 4.5 - 7.6 GHz 3 FILTERS - TUNABLE - SMT Evaluation PCB List of Materials for Evaluation PCB 128531 [1] Item J1 - J3 Description SMA - SRI C1, C2 100 pF Capacitor, 0402 Pkg. U1 HMC882LP5E Filter PCB [2] 127338 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR or Rogers 25FR The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohms impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 3 - 13