Ultra Small Surface Mount Coaxial Connectors 1.4mm or 1.65mm Mated Height W.FL Series Occupied Mounting Area W.FL Series U.FL Series Fig.1 Features Mated height comparison Receptacle: 5.6 mg Right-angle plug: 18.6 mg(040), 28.2mg(062) 4. Frequency range up to 6 GHz B6M'#% &#. L#;A"AE<"%+'=; B6M'#) 3. Extremely light weight J#;A"AEK"%)%=; J#;A"AE"%+'=; '#( The W.FL Series is about 55% smaller than our U.FL Series connector and only uses 3.4mm2 of PCB space. The PCB layout for the W.FL Series is the same as for W.FL2 and X.FL Series. Note:This product is not compatible with W.FL2 Series and X.FL Series.(Fig.1) L#;A"AE"%)% L#;A"AE"%)%=; &#+* B6M&#-* 2. Small board footprint &#) B6M&#** 1. Nominal mated height of 1.4 mm or 1.65mm (Max. 1.55 or 1.85mm)(Fig.2) DC to 3 GHz : V.S.W.R. of 1.3 max. 3 GHz to 6 GHz: V.S.W.R. of 1.4 max. Fig.2 5. Automatic board placement 7. Simple connector mating / unmating Use of the available mating/un-mating tools assures correct connection/disconnection of the plug and receptacle. W.FL-LP-040 W.FL-LP-040HF O0.81 2.85 W.FL-LP(G)-062HF 3.65 O1 The use of ultra-fine coaxial(fluorinated resin insulated) cables on these connectors offer the ability to complete connections in small, confined spaces with a smooth, easy operation. 1.4 (MAX1.55) 6. Plugs are terminated with ultra-fine coaxial (fluorinated resin insulated) cable W. FL Plug and Receptacle 1.65 (MAX1.85) Packaged on tape-and-reel the receptacles can be placed with vacuum nozzles of the automatic placement equipment. 8. Halogen-free*(Receptacle, Plug(HF type)) Fig.3 *As defined by IEC61249-2-21 Br-900ppm maximum, Cl-900 ppm maximum, Cl+Br combined-1,500 ppm maximum Applications Mobile phones, wireless communication devices, electronic measuring instruments, GPS, wireless LAN, Bluetooth and any application requiring high frequency transmission using small coaxial connectors. 2014.11e 1 W.FL SeriesUltra Small Surface Mount Coaxial Connectors 1.4mm or 1.65mm Mated Height Specifications Nominal characteristic impedance 50 ohms Operating temperature range DC to 6 GHz Storage temperature range Rating Frequency range Item 1. Contact resistance Specification Center contact: 20m ohms max. Outer contact: 10m ohms max. -40C to +90C (90% RH max.) -30C to +70C (90% RH max.) Conditions 10mA max. 2. Insulation resistance 500M ohms min. 100V DC 3. Withstanding voltage No flashover or insulation breakdown 200V AC / 1 minute 4. V.S.W.R.* 1.3 Max. 1.4 Max. Up to 3 GHz 3 to 6 GHz *V.S.W.R. Measurement System Measured as shown on the block diagram below. Network Analyzer Test Set Test Port D.U.T Test Port Cable Note1: Measurement way of a W.FL Cable assembly (plug) W.FL Cable assembly (plug) is measured with SMA conversion adapters mated with W.FL plugs at both ends of a 100cm coaxial cable harness Termination Note2: Measurement way of a W.FL receptacle W.FL receptacle, which is mounted on a 50 ohms glass epoxy board, is measured with a SMA conversion adapter. Materials Plug - right angle Part Shell Female center contact Insulator Material Phosphor bronze Phosphor bronze Finish / Remarks Silver plated Gold plated Color: Black, UL94V-0(040) Color: Gray, UL94V HB(040HF, 062HF) PBT Receptacle Part Shell Insulator Male center contact Material Phosphor bronze LCP Brass Finish / Remarks Silver plated Color: Black, UL94V-0 Gold plated Cable Assembly(Plug) 2 W.FL-LP-040(06), W.FL-LP-040HF(06) (Applicable cable: outer diameter 0.81) 1.15 2.85 '#&' W.FL-LP-062HF(06) (Applicable cable: outer diameter 1.0) &#(- (#+* [Plugs can be ordered only as terminated cable assemblies.] 2 W.FL SeriesUltra Small Surface Mount Coaxial Connectors 1.4mm or 1.65mm Mated Height BHow to Specify Cable Assembly [Double-ended cable assembly] [Single-ended cable assembly] L(mm) L(mm) Ordering Information Ordering Information Standard tolerances for (L) Used plug:W.FL-LP-040(06), W.FL-LP-040HF(06) (Dia. 0.81) Double-Ended W.FL -- 2LP HF6 --04N q w e r TV -- A -- L t y u (L)mm Standard tolerance(mm) *L=35 to 200 4 1L=200 to 500 8 1L=500 to 1000 12 L=Longer than 1000 1.5% of (L) Note: Minimum available length(L) is 35mm. Single-Ended W.FL -- LP HF6 --04N q w e r TV -- A -- L t y u q Series name w Assembly type W.FL LP : Single ended 2LP : Double ended e Environmental compliant HF6 : Halogen-free 6 : RoHS compliant r Cable type t Cable Color y Cable outer conductor u Total length(mm) 04N 1 2 TV : 0.81mm dia. ultra-fine coaxial cable : White : Black : Tin plated braided wire Length(L) Used plug:W.FL-LP(G)-062HF(06) (Dia. 1) Double-Ended W.FL -- 2LPG HF -- 062N q w e r D -- A -- L t y u Single-Ended W.FL -- LPG HF -- 062N q w e r D -- A -- L t y u q Series name w Assembly type W.FL LPG : Single ended 2LPG : Double ended e Environmental compliant HF : Halogen-free 062N: 1.0mm dia. ultra-fine coaxial cable r Cable type 1 : Gray 2 : Black t Cable Color 3 : White D : Copper tape + Outer tin plated braided wire y Cable outer conductor u Total length(mm) Length(L) 3 W.FL SeriesUltra Small Surface Mount Coaxial Connectors 1.4mm or 1.65mm Mated Height Receptacle BRecommended PCB mounting pattern 0.85 0.3 0.25 2.6 2 0.5 1.3 1.7 1.3 1.4 1.5 SIG 0.3 GND SIG GND No conductive traces in this area 0.65 2 1.3 1.7 Note: The land pattern is the same as that of the X.FL, W.FL2 series connectors. All dimensions: mm Part No. HRS No. Packaging W.FL-R-SMT-1(60) 331-0482-6 60 Reel (5,000 pcs/reel) W.FL-R-SMT-1(80) 331-0482-6 80 Reel (10,000 pcs/reel) Embossed Carrier Tape Dimensions(IEC 60286-3 compliant) Embossed Carrier Tape Dimensions RoHS Yes Reel Dimensions (W.FL-R-SMT-1(60) 8mm pitch) 8 Unreeling direction 13.5 MaterialPS(Black) O330 12 5.5 1.75 2 A (W.FL-R-SMT-1(80) 4mm pitch) 4 Unreeling direction A(SCALE FREE) 2 O13 12 5.5 1.75 2 O2 1 4 W.FL SeriesUltra Small Surface Mount Coaxial Connectors 1.4mm or 1.65mm Mated Height Conversion Adapters SMA Conversion Adapter (W.FL side jack - SMA side plug) (10.3) 8HEX W.FL SMA Note:Used for performance measurements only. The W.FL mating side has lower retention force than the regular product when mated to the corresponding part. Part No. HRS No. Packaging RoHS HRMP-W.FLJ(40) 311-0367-3 40 1 Yes SMA Conversion Adapter (W.FL side plug - SMA side jack) 13.8 (4.05) 6 5.6 O6.35 SMA 1/4-36UNS-2A Note:Used for performance measurements only. The W.FL mating side has lower retention force than the regular product when mated to the corresponding part. W.FL Part No. HRS No. Packaging RoHS HRMJ-W.FLP(40) 311-0368-6 40 1 Yes SMA Conversion Adapter (18.35) (4) 5.5 O6.35 6 1/4-36UNS-2A Note:When mating with corresponding part (W.FLR-SMT-1) it must be pressed down and held to make complete connection. Part No. HRS No. HRMJ-W.FLP-ST1(40) 311-0386-8 40 Packaging RoHS 1 Yes 5 W.FL SeriesUltra Small Surface Mount Coaxial Connectors 1.4mm or 1.65mm Mated Height Receptacle Inspection Adapter Used for inspecting the performance parameters of the cable assembly. 12.1 (7.9) 4.2 (4.4) 1 7HEX M50.5 Part No. HRS No. Packaging RoHS W.FL-R-1 331-0483-9 1 Yes Plug-Mating Tool This tool is used for mating a plug. 8 O10 (100) Part No. HRS No. Packaging RoHS W.FL-LP-IN 331-0323-2 1 Yes Plug-Extraction Tool (100) 40 6 5) (O1 Part No. HRS No. Packaging RoHS W.FL-LP-N 331-0492-0 1 Yes W.FL SeriesUltra Small Surface Mount Coaxial Connectors 1.4mm or 1.65mm Mated Height BPrecautions 1. Plug (1) Mating / unmating * Unmating Insert both ends of the extraction tool under the plug (from the direction opposite to the Cable termination), as shown and pull-up in the direction perpendicular to the mounting surface of the receptacle. W.FL-LP-N plug extraction tool Recomended the use of the extraction tool for unmating. W.FL Cable Assembly Any attempt of unmating by pulling on the cable may result in damage and affect the mechanical / electrical performance. W.FL-R-SMT-1 * Mating qAlign the mating tool W.FL-LP-IN or the mating end of the tool over the plug end of the cable assembly. wFirmly place the tool over the plug until it is secured in the tool. ePlace the plug cable assembly (held in the tool)over the corresponding receptacle. rAssuring that the plug and receptacle are aligned press-down perpendicular to the mounting surface until both connectors are fully mated. tRemove the mating tool by carefully pulling it up.Removal of the tool. q w e Plug pickup (2) Pull forces on the cable after connectors are mated t Insertion to a receptacle Removal of the tool W.FL Cable Assembly After the connectors are mating, do not apply a load to the cable in excess of the values indicated in the diagram. r W.FL-R-SMT-1 Receptacle 2N max (3) Precautions Do not twist connectors excessively during mating / unmating. 2. Receptacle (1) Recommended reflow temperature profile 250 c max. for 10 seconds [c] 260 240 220 200 180 160 140 120 100 80 Preheat (130 to 180c) 120 seconds max. 230c 220c 50 seconds max. 60 seconds max. Time qThe temperature of the printed circuit board surface temperature at the points of contact with the terminals. wReflow soldering should be performed at a printed circuit surface temperature of 250C max. eIn individual applications the actual temperature may vary, depending on the solder paste type, volume / thickness and board size / thickness. Consuly your solder paste and equipment manufacturer for specific recommendations. (2) Recommended metal mask thickness 0.1 mm to 0.12 mm (3) Reflow cycles 2 times 3. Operating environment and storage conditions (1) Operating environment (2) Storage conditions Receptacle The connectors are not designed to operate in the following environments: * Exposed to a excessive amounts of fine particles and dust * Regions and places having a high density of sulfur dioxide, hydrogen sulfide, nitrogen dioxide or other corrosive gasses. * Environments having large rapid variations in temperature. Store in the Hirose Electric packaging. Temperature: -10 to +40c, Humidity: 85% max. Use within 6 months of delivery. Receptacles for which the storage period has elapsed must be tested for solderability to the PC board mounting surface. 7 W.FL SeriesUltra Small Surface Mount Coaxial Connectors 1.4mm or 1.65mm Mated Height USA: HIROSE ELECTRIC (U.S.A.), INC. HEADQUARTERS 2688 Westhills Court, Simi Valley, CA 93065-6235 Phone : +1-805-522-7958 Fax : +1-805-522-3217 http://www.hirose.com/us/ USA: HIROSE ELECTRIC (U.S.A.), INC. SAN JOSE OFFICE 3255 Scott Boulevard, Building 7, Suite 101 Santa Clara, CA 95054 Phone : +1-408-253-9640 Fax : +1-408-253-9641 http://www.hirose.com/us/ USA: HIROSE ELECTRIC (U.S.A.), INC. CHICAGO OFFICE 580 Waters Edge Lane, Suite 205 Lombard IL 60148 Phone : +1-630-282-6706 Mail : inquiries@hirose.com http://www.hirose.com/us/ USA: HIROSE ELECTRIC (U.S.A.), INC. DETROIT OFFICE (AUTOMOTIVE) 37677 Professional Center Drive, Suite #100C Livonia, MI 48154 Phone : +1-734-542-9963 Fax : +1-734-542-9964 http://www.hirose.com/us/ THE NETHERLANDS: HIROSE ELECTRIC EUROPE B.V. Hogehillweg #8 1101 CC Amsterdam Z-O Phone : +31-20-6557460 Fax : +31-20-6557469 http://www.hirose.com/eu/ GERMANY: HIROSE ELECTRIC EUROPE B.V. GERMAN BRANCH Herzog-Carl-Strasse 4 D-73760 Ostfildern (Scharnhauser Park) Phone : +49-711-4560-02-1 Fax : +49-711-4560-02-299 http://www.hirose.com/eu/ GERMANY: HIROSE ELECTRIC EUROPE B.V. NUERNBERG OFFICE Muggenhofer Str. 136 90429 Nuernberg Phone : +49-911 32 68 89 63 Fax : +49-911 32 68 89 69 http://www.hirose.com/eu/ UNITED KINGDOM: HIROSE ELECTRIC EUROPE BV (UK BRANCH) 4 Newton Court, Kelvin Drive, Knowlhill, Milton Keynes, MK5 8NH Phone : +44-1908 202050 Fax : +44-1908 202058 http://www.hirose.com/eu/ CHINA: HIROSE ELECTRIC (SHANGHAI) CO., LTD. 1601, Henderson Metropolitan, NO.300, East Nanjing Road, Huangpu District, Shanghai, China 200001 Phone : +86-21-6391-3355 Fax : +86-21-6391-3335 http://www.hirose.com/cn/ CHINA: HIROSE ELECTRIC (SHANGHAI) CO.,LTD. BEIJING BRANCH A1001, Ocean International Center, Building 56# East 4th Ring Middle Road, ChaoYang District, Beijing, 100025 Phone : +86-10-5165-9332 Fax : +86-10-5908-1381 http://www.hirose.com/cn/ CHINA: HIROSE ELECTRIC TECHNOLOGIES (SHENZHEN) CO., LTD. Room 09-13, 19/F, Office Tower Shun Hing Square, Di Wang Commercial Centre, 5002 Shen Nan Dong Road, Shenzhen City, Guangdong Province, 518008 Phone : +86-755-8207-0851 Fax : +86-755-8207-0873 http://www.hirose.com/cn/ HONG KONG: HIROSE ELECTRIC HONGKONG TRADING CO., LTD. Room 1001, West Wing, Tsim Sha Tsui Centre, 66 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong Phone : +852-2803-5338 Fax : +852-2591-6560 http://www.hirose.com/hk/ TAIWAN: HIROSE ELECTRIC TAIWAN CO., LTD. 103 8F, No.87, Zhengzhou Rd., Taipei Phone : +886-2-2555-7377 Fax : +886-2-2555-7350 http://www.hirose.com/cn/ KOREA: SINGAPORE: HIROSE KOREA CO., LTD. HIROSE ELECTRIC SINGAPORE PTE. LTD. 1261-10, Jeoungwhang-Dong, Shihung-City, 10 Anson Road #26-1, International Plaza Kyunggi-Do 429-450 079903, Singapore Phone : +82-31-496-7000,7124 Phone : +65-6324-6113 Fax : +82-31-496-7100 Fax : +65-6324-6123 http://www.hirose.com/sg/ http://www.hirose.co.kr/ INDIA: HIROSE ELECTRIC SINGAPORE PTE. LTD. DELHI LIAISON OFFICE Office NO.519, Regus-Green Boulevard, Level5, Tower C, Sec62, Plot B-9A, Block B, Noida, 201301, Uttar Pradesh, India Phone : +91-12-660-8018 Fax : +91-120-4804949 http://www.hirose.com/sg/ INDIA: HIROSE ELECTRIC SINGAPORE PTE. LTD. BANGALORE LIAISON OFFICE Unit No.03, Ground Floor, Explorer Building International Tech Park Whitefield Road, Bangalore 560066 Karnataka, India Phone : +91-80-4120 1907 Fax : +91-80-4120 9908 http://www.hirose.com/sg/ (R) 8 MALAYSIA: HIROSE ELECTRIC SINGAPORE PTE. LTD. (REPRESENTATIVE OFFICE) 1-10-07, Suntech @ Penang Cybercity (1164),Lintang Mayang Pasir 3,11950, Bayan Baru, Penang, Malaysia. Phone : +604-619-2564 Fax : +604-619-2574 http://www.hirose.com/sg/ 2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN TEL: +81-45-620-3526 Fax: +81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 11/2014. Contents are subject to change without notice for the purpose of improvements. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Hirose Electric: W.FL-LP-04N1-A-(800) W.FL-LP-04N1-A-(90) W.FL-LP-04N1-A-(60) W.FL-LP-04N1-A-(80) W.FL-LP-04N1-A-(40) W.FL-LP-04N1-A-(70) W.FL-LP-04N1-A-(190) W.FL-LP-04N1-A-(110) W.FL-LP-04N1-A-(400) W.FL-LP-04N1-A-(210) W.FL-LP-04N1-A-(50) W.FL-LP-04N1-A-(250) W.FL-LP-04N1-A-(35) W.FL-LP-04N1-A-(260) W.FL-LP-04N1-A-(220) W.FL-LP-04N1-A-(200) W.FL-LP-04N1-A-(150) W.FL-LP-04N1-A-(900) W.FL-LP-04N1-A-(130) W.FL-LP-04N1-A(170) W.FL-LP-04N1-A-(140) W.FL-LP-04N1-A-(100) W.FL-LP-04N1-A-(180) W.FL-LP-04N1-A-(160) W.FL-LP04N1-A-(120) W.FL-LP-04N1-A-(600) W.FL-LP-IN W.FL-LP-04N1-A-(700) W.FL-LP-04N1-A-(300) W.FL-LP-04N1-A(500) W.FL-LP-04N1-A-(1000) W.FL-R-SMT-1(40) W.FL-LP-N W.FL-R-1 W.FL-R-SMT-1(10) W.FL/CR-AD(63) W.FL/CR-AD(62) W.FL/CR-AD(61) W.FL/CR-AD(65) W.FL/CR-AD(66) W.FL/CR-AD(64) W.FL/CR-AD(67) W.FL-RSMT-1(60) W.FL-R-SMT-1(80) W.FL2P-ML51.J-PA(F)-ST