ADC08L060 www.ti.com SNAS167G - MAY 2002 - REVISED MARCH 2013 ADC08L060 8-Bit, 10 MSPS to 60 MSPS, 0.65 mW/MSPS A/D Converter with Internal Sample-and-Hold Check for Samples: ADC08L060 FEATURES DESCRIPTION * * * * * The ADC08L060 is a low-power, 8-bit, monolithic analog-to-digital converter with an on-chip track-andhold circuit. Optimized for low cost, low power, small size and ease of use, this product operates at conversion rates of 10 MSPS to 60 MSPS while consuming just 0.65 mW per MHz of clock frequency, or 39 mW at 60 MSPS. Raising the PD pin puts the ADC08L060 into a Power Down mode where it consumes about 1 mW. 1 2 Single-ended input Internal sample-and-hold function Low voltage (single +3V) operation Small package Power-down feature KEY SPECIFICATIONS * * * * * * * * * * Resolution 8 bits Conversion rate 60 MSPS DNL 0.25 LSB (typ) INL +0.5/-0.2 LSB (typ) SNR (10.1 MHz) 48 dB (typ) ENOB (10.1 MHz) 7.6 bits (typ) THD (10.1 MHz) -57 dB (typ) Latency 5 Clock Cycles No missing codes Ensured Power Consumption - Operating 0.65 mW/MSPS (typ) - Power Down Mode 1.0 mW (typ) The unique architecture achieves 7.6 Effective Bits. The ADC08L060 is resistant to latch-up and the outputs are short-circuit proof. The top and bottom of the ADC08L060s reference ladder are available for connections, enabling a wide range of input possibilities. The digital outputs are TTL/CMOS compatible with a separate output power supply pin to support interfacing with 1.8V to 3V logic. The output coding is straight binary and the digital inputs (CLK and PD) are TTL/CMOS compatible. The ADC08L060 is offered in a 24-lead plastic package (TSSOP) and is specified over the industrial temperature range of -40C to +85C. APPLICATIONS * * * * * * Digital Imaging Set-top boxes Portable Instrumentation Communication Systems X-ray imaging Viterbi decoders 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2002-2013, Texas Instruments Incorporated ADC08L060 SNAS167G - MAY 2002 - REVISED MARCH 2013 www.ti.com Block Diagram VDR VA (pin 18) VRT 17 COARSE/FINE COMPARATORS 1 ENCODER & ERROR CORRECTION 8 17 8 SWITCHES V RM MUX 17 COARSE/FINE COMPARATORS 256 VRB ENCODER & ERROR CORRECTION 8 OUTPUT DRIVERS DATA OUT 8 CLOCK GEN CLK VIN VIN GND AGND PD DR GND (pin 17) Pin Configuration 2 Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 ADC08L060 www.ti.com SNAS167G - MAY 2002 - REVISED MARCH 2013 Table 1. Pin Descriptions and Equivalent Circuits Pin No. Symbol Equivalent Circuit 6 VIN Analog signal input. Conversion range is VRB to VRT. 3 VRT Analog Input that is the high (top) side of the reference ladder of the ADC. Nominal range is 0.5V to VA. Voltage on VRT and VRB inputs define the VIN conversion range. Bypass well. See Section 2.0 for more information. 9 VRM Mid-point of the reference ladder. This pin should be bypassed to a quiet point in the analog ground plane with a 0.1 F capacitor. 10 VRB Analog Input that is the low side (bottom) of the reference ladder of the ADC. Nominal range is 0.0V to (VRT - 0.5V). Voltage on VRT and VRB inputs define the VIN conversion range. Bypass well. See Section 2.0 for more information. 23 PD 24 CLK VA Description Power Down input. When this pin is high, the converter is in the Power Down mode and the data output pins hold the last conversion result. CMOS/TTL compatible digital clock Input. VIN is sampled on the rising edge of CLK input. GND 13 thru 16 and 19 thru 22 D0-D7 7 VIN GND 1, 4, 12 VA Positive analog supply pin. Connect to a quiet voltage source of +3V. VA should be bypassed with a 0.1 F ceramic chip capacitor for each pin, plus one 10 F capacitor. See Section 3.0 for more information. 18 VDR Power supply for the output drivers. If connected to VA, decouple well from VA. 17 DR GND 2, 5, 8, 11 AGND Conversion data digital Output pins. D0 is the LSB, D7 is the MSB. Valid data is output after the rising edge of the CLK input. Reference ground for the single-ended analog input, VIN. The ground return for the output driver supply. The ground return for the analog supply. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 3 ADC08L060 SNAS167G - MAY 2002 - REVISED MARCH 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) Supply Voltage (VA) 3.8V Driver Supply Voltage (VDR) VA +0.3V -0.3V to VA Voltage on Any Input or Output Pin Reference Voltage (VRT, VRB) VA to AGND -0.05V to (VA + 0.05V) CLK, PD Voltage Range Input Current at Any Pin Package Input Current (3) 25 mA (3) 50 mA Power Dissipation at TA = 25C See (4) (5) ESD Susceptibility Human Body Model Machine Model 2500V 200V Soldering Temperature, Infrared, 10 seconds (5) 235C -65C to +150C Storage Temperature (1) (2) (3) (4) (5) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such condition. All voltages are measured with respect to GND = AGND = DR GND = 0V, unless otherwise specified. When the input voltage at any pin exceeds the power supplies (that is, less than AGND or DR GND, or greater than VA or VDR), the current at that pin should be limited to 25 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 25 mA to two. The absolute maximum junction temperature (TJmax) for this device is 150C. The maximum allowable power dissipation is dictated by TJmax, the junction-to-ambient thermal resistance (JA), and the ambient temperature (TA), and can be calculated using the formula PDMAX = (TJmax - TA) / JA. The values for maximum power dissipation will be reached only when this device is operated in a severe fault condition (e.g., when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided. See AN-450, "Surface Mounting Methods and Their Effect on Product Reliability" (SNOA742). (1) (2) Operating Ratings -40C TA +85C Operating Temperature Range Supply Voltage, VA +2.4V to +3.6V Driver Supply Voltage, VDR +2.4V to VA Output Driver Voltage, VDR 1.8V to VA Ground Difference |GND - DR GND| 0V to 300 mV Upper Reference Voltage (VRT) 0.5V to (VA -0.3V) Lower Reference Voltage (VRB) 0V to (VRT -0.5V) VIN Voltage Range (1) (2) VRB to VRT Absolute Maximum Ratings indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such condition All voltages are measured with respect to GND = AGND = DR GND = 0V, unless otherwise specified. Package Thermal Resistance 4 Package JA 24-Lead TSSOP 92C/W Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 ADC08L060 www.ti.com SNAS167G - MAY 2002 - REVISED MARCH 2013 Converter Electrical Characteristics The following specifications apply for VA = VDR = +3.0VDC, VRT = +1.9V, VRB = 0.3V, CL = 10 pF, fCLK = 60 MHz at 50% duty cycle. Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25C (1) (2) (3) Symbol Parameter Conditions Typical Limits (4) Units (Limits) (4) DC ACCURACY INL Integral Non-Linearity +0.5 -0.2 +1.9 -1.35 LSB (max) LSB (min) DNL Differential Non-Linearity 0.25 0.90 LSB (max) 0 (max) FSE Missing Codes Full Scale Error 3.0 13 mV (max) VOFF Zero Scale Offset Error 19 27 mV (max) ANALOG INPUT AND REFERENCE CHARACTERISTICS V (min) VRT V (max) Input Voltage CIN VIN Input Capacitance 4 pF RIN RIN Input Resistance >1 M BW Full Power Bandwidth 270 MHz VRT Top Reference Voltage 1.9 VRB RREF (1) (2) (3) (4) VIN = 0.75V +0.5 Vrms (CLK LOW) (CLK HIGH) Bottom Reference Voltage VRT - VRB Iref 1.6 VRB VIN 0.3 Reference Delta Reference Ladder Resistance Reference Ladder Current 3 1.6 VRT to VRB VRT to VRB 720 2.2 pF VA V (max) 0.5 V (min) VRT - 0.5 V (max) 0 V (min) 2.3 V (max) 1.0 V (min) 590 (min) 1070 (max) 1.5 mA (min) 2.7 mA (max) The Electrical characteristics tables list ensured specifications under the listed Recommended Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations for room temperature only and are not ensured. The analog inputs are protected as shown below. Input voltage magnitudes up to VA + 300 mV or to 300 mV below GND will not damage this device. However, errors in the A/D conversion can occur if the input goes above VDR or below GND by more than 100 mV. For example, if VA is 2.7VDC the full-scale input voltage must be 2.8VDC to ensure accurate conversions. To ensure accuracy, it is required that VA and VDR be well bypassed. Each supply pin must be decoupled with separate bypass capacitors. Typical figures are at TJ = 25C, and represent most likely parametric norms at specific conditions at the time of product characterization and are not ensured. Test limits are specifid to TI's AOQL (Average Outgoing Quality Level). Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 5 ADC08L060 SNAS167G - MAY 2002 - REVISED MARCH 2013 www.ti.com Converter Electrical Characteristics (continued) The following specifications apply for VA = VDR = +3.0VDC, VRT = +1.9V, VRB = 0.3V, CL = 10 pF, fCLK = 60 MHz at 50% duty cycle. Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25C (1)(2) (3) Symbol Parameter Typical Conditions (4) Limits (4) Units (Limits) CLK, PD DIGITAL INPUT CHARACTERISTICS VIH Logical High Input Voltage VDR = VA = 3.6V 2.0 V (min) VIL Logical Low Input Voltage VDR = VA = 2.7V 0.8 V (max) IIH Logical High Input Current VIH = VDR = VA = 3.6V 10 nA IIL Logical Low Input Current VIL = 0V, VDR = VA = 2.7V -50 nA CIN Logic Input Capacitance 3 pF DIGITAL OUTPUT CHARACTERISTICS VOH High Level Output Voltage VA = VDR = 2.7V, IOH = -400 A 2.6 2.4 V (min) VOL Low Level Output Voltage VA = VDR = 2.7V, IOL = 1.0 mA 0.4 0.5 V (max) fIN = 10.1 MHz, VIN = FS - 0.25 dB 7.6 6.9 Bits (min) fIN = 29 MHz, VIN = FS - 0.25 dB 7.4 fIN = 10.1 MHz, VIN = FS - 0.25 dB 47.4 43.3 dB (min) fIN = 29 MHz, VIN = FS - 0.25 dB 46.1 DYNAMIC PERFORMANCE ENOB Effective Number of Bits SINAD Signal-to-Noise & Distortion SNR Signal-to-Noise Ratio SFDR Spurious Free Dynamic Range THD Total Harmonic Distortion HD2 2nd Harmonic Distortion HD3 3rd Harmonic Distortion IMD Intermodulation Distortion fIN = 10.1 MHz, VIN = FS - 0.25 dB 48 Bits dB 44.5 dB (min) fIN = 29 MHz, VIN = FS - 0.25 dB 47.2 dB fIN = 10.1 MHz, VIN = FS - 0.25 dB 59.1 dBc fIN = 29 MHz, VIN = FS - 0.25 dB 54.5 dBc fIN = 10.1 MHz, VIN = FS - 0.25 dB -56.9 dBc fIN = 29 MHz, VIN = FS - 0.25 dB -53.3 dBc fIN = 10.1 MHz, VIN = FS - 0.25 dB -61.1 dBc fIN = 29 MHz, VIN = FS - 0.25 dB -54.9 dBc fIN = 10.1 MHz, VIN = FS - 0.25 dB -64.2 dBc fIN = 29 MHz, VIN = FS - 0.25 dB -63.1 dBc f1 = 11 MHz, VIN = FS - 6.25 dB f2 = 12 MHz, VIN = FS - 6.25 dB -55 dBc DC Input 13 fIN = 10 MHz, VIN = FS - 3 dB 14 POWER SUPPLY CHARACTERISTICS IA Analog Supply Current DRID Output Driver Supply Current DC Input fIN = 10 MHz, VIN = FS - 3 dB 0.04 (5) DC Input IA + DRID PC Total Operating Current Power Consumption CLK Low, PD = Hi 0.33 DC Input 39 fIN = 10 MHz, VIN = FS - 3 dB, PD = Low 53 CLK Low, PD = Hi Power Supply Rejection Ratio PSRR2 Power Supply Rejection Ratio SNR reduction with 200 mV at 1MHz on supply (5) 6 13 18.2 PSRR1 mA (max) 0.2 mA (max) mA 4.2 fIN = 10 MHz, VIN = FS - 3 dB, PD = Low FSE change with 2.7V to 3.3V change in VA 15.9 mA 16.1 mA (max) mA mA 48.3 mW (max) mW 1 mW -51 dB 45 dB IDR is the current consumed by the switching of the output drivers and is primarily determined by the load capacitance on the output pins, the supply voltage, VDR, and the rate at which the outputs are switching (which is signal dependent), IDR = VDR (CO x fO + C1 x f1 + ... + C71 x f7) where VDR is the output driver power supply voltage, Cn is the total capacitance on any given output pin, and fn is the average frequency at which that pin is toggling. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 ADC08L060 www.ti.com SNAS167G - MAY 2002 - REVISED MARCH 2013 Converter Electrical Characteristics (continued) The following specifications apply for VA = VDR = +3.0VDC, VRT = +1.9V, VRB = 0.3V, CL = 10 pF, fCLK = 60 MHz at 50% duty cycle. Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25C (1)(2) (3) Symbol Parameter Conditions Typical Limits (4) Units (Limits) 60 MHz (min) (4) AC ELECTRICAL CHARACTERISTICS fC1 Maximum Conversion Rate 80 fC2 Minimum Conversion Rate 10 MHz tCL Minimum Clock Low Time 0.62 ns (min) tCH Minimum Clock High Time 0.62 ns (min) 5 95 %(min) %(max) DC Clock Duty Cycle tOH Output Hold Time tOD Output Delay CLK to Data Invalid CLK to Data Transition Pipeline Delay (Latency) tAD Sampling (Aperture) Delay tAJ Aperture Jitter 5.2 7.1 5 CLK Rise to Acquisition of Data ns 5.0 9.4 ns (min) ns (max) Clock Cycles 2.6 ns 2 ps rms Specification Definitions APERTURE (SAMPLING) DELAY is that time required after the rise of the clock input for the sampling switch to open. The Sample/Hold circuit effectively stops capturing the input signal and goes into the "hold" mode tAD after the clock goes high. APERTURE JITTER is the variation in aperture delay from sample to sample. Aperture jitter shows up as input noise. CLOCK DUTY CYCLE is the ratio of the time that the clock wave form is at a logic high to the total time of one clock period. DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1 LSB. Measured at 60 MSPS with a ramp input. EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise and Distortion Ratio, or SINAD. ENOB is defined as (SINAD - 1.76) / 6.02 and says that the converter is equivalent to a perfect ADC of this (ENOB) number of bits. FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental drops 3 dB below its low frequency value for a full scale input. FULL-SCALE ERROR is a measure of how far the last code transition is from the ideal 11/2 LSB below VRT and is defined as: Vmax + 1.5 LSB - VRT (1) where Vmax is the voltage at which the transition to the maximum (full scale) code occurs. INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from zero scale (1/2 LSB below the first code transition) through positive full scale (1/2 LSB above the last code transition). The deviation of any given code from this straight line is measured from the center of that code value. The end point test method is used. Measured at 60 MSPS with a ramp input. INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two sinusoidal frequencies being applied to the ADC input at the same time. it is defined as the ratio of the power in the second and third order intermodulation products to the power in one of the original frequencies. IMD is usually expressed in dBFS. LSB (LEAST SIGNIFICANT BIT) is the bit that has the smallest value or weight of all bits. This value is (VRT - VRB) / 2n (2) where "n" is the ADC resolution, which is 8 in the case of the ADC08L060. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 7 ADC08L060 SNAS167G - MAY 2002 - REVISED MARCH 2013 www.ti.com MISSING CODES are those output codes that are skipped and will never appear at the ADC outputs. These codes cannot be reached with any input value. MSB (MOST SIGNIFICANT BIT) is the bit that has the largest value or weight. Its value is one half of full scale. OUTPUT DELAY is the time delay after the rising edge of the input clock before the data update is present at the output pins. OUTPUT HOLD TIME is the length of time that the output data is valid after the rise of the input clock. PIPELINE DELAY (LATENCY) is the number of clock cycles between initiation of conversion and when that data is presented to the output driver stage. New data is available at every clock cycle, but the data lags the conversion by the Pipeline Delay plus the Output Delay. POWER SUPPLY REJECTION RATIO (PSRR) is a measure of how well the ADC rejects a change in the power supply voltage. For the ADC08L060, PSRR1 is the ratio of the change in Full-Scale Error that results from a change in the d.c. power supply voltage, expressed in dB. PSRR2 is a measure of how well an a.c. signal riding upon the power supply is rejected and is here defined as (3) where SNR0 is the SNR measured with no noise or signal on the supply lines and SNR1 is the SNR measured with a 1 MHz, 200 mVP-P signal riding upon the supply lines. SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal at the output to the rms value of the sum of all other spectral components below one-half the sampling frequency, not including harmonics or d.c. SIGNAL TO NOISE PLUS DISTORTION (S/(N+D) or SINAD) is the ratio, expressed in dB, of the rms value of the input signal at the output to the rms value of all of the other spectral components below half the clock frequency, including harmonics but excluding d.c. SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the rms values of the input signal at the output and the peak spurious signal, where a spurious signal is any signal present in the output spectrum that is not present at the input. TOTAL HARMONIC DISTORTION (THD) is the ratio expressed in dB, of the rms total of the first nine harmonic levels at the output to the level of the fundamental at the output. THD is calculated as THD = 20 x log A 2 +... +A 2 f2 f10 A f12 (4) where Af1 is the RMS power of the fundamental (output) frequency and Af2 through Af10 are the RMS power of the first 9 harmonic frequencies in the output spectrum. ZERO SCALE OFFSET ERROR is the error in the input voltage required to cause the first code transition. It is defined as VOFF = VZT - VRB (5) where VZT is the first code transition input voltage. 2nd HARMONIC DISTORTION (2nd HARM) is the difference, expressed in dB, between the rms power in the output fundamental frequency and the power in its 2nd harmonic at the output. 3rd HARMONIC DISTORTION (3rd HARM) is the difference, expressed in dB, between the rms power in the output fundamental frequency and the power in its 3rd harmonic at the output. 8 Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 ADC08L060 www.ti.com SNAS167G - MAY 2002 - REVISED MARCH 2013 Timing Diagram Figure 1. ADC08L060 Timing Diagram Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 9 ADC08L060 SNAS167G - MAY 2002 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics VA = VDR = 3V, fCLK = 60 MHz, fIN = 10 MHz, unless otherwise stated 10 INL INL vs Temperature Figure 2. Figure 3. INL vs Supply Voltage, VA INL vs Sample Rate Figure 4. Figure 5. INL vs Clock Duty Cycle DNL Figure 6. Figure 7. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 ADC08L060 www.ti.com SNAS167G - MAY 2002 - REVISED MARCH 2013 Typical Performance Characteristics (continued) VA = VDR = 3V, fCLK = 60 MHz, fIN = 10 MHz, unless otherwise stated DNL vs Temperature DNL vs Supply Voltage, VA Figure 8. Figure 9. DNL vs Sample Rate DNL vs Clock Duty Cycle Figure 10. Figure 11. SNR, SINAD and SFDR vs Temperature SNR, SINAD and SFDR vs Supply Voltage, VA Figure 12. Figure 13. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 11 ADC08L060 SNAS167G - MAY 2002 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) VA = VDR = 3V, fCLK = 60 MHz, fIN = 10 MHz, unless otherwise stated 12 SNR, SINAD and SFDR vs Sample Rate SNR, SINAD and SFDR vs Input Frequency Figure 14. Figure 15. SNR, SINAD and SFDR vs Clock Duty Cycle Distortion vs Temperature Figure 16. Figure 17. Distortion vs Supply Voltage, VA Distortion vs Sample Rate Figure 18. Figure 19. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 ADC08L060 www.ti.com SNAS167G - MAY 2002 - REVISED MARCH 2013 Typical Performance Characteristics (continued) VA = VDR = 3V, fCLK = 60 MHz, fIN = 10 MHz, unless otherwise stated Distortion vs Input Frequency Distortion vs Clock Duty Cycle Figure 20. Figure 21. Power Consumption (Active) vs. Sample Rate (fIN = d.c.) Power Consumption (Active) vs. Sample Rate (fIN = d.c.) Figure 22. Figure 23. Power Consumption (Active) vs. Sample Rate (fIN = 1 MHz) Power Consumption (Active) vs. Sample Rate (fIN = 1 MHz) Figure 24. Figure 25. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 13 ADC08L060 SNAS167G - MAY 2002 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) VA = VDR = 3V, fCLK = 60 MHz, fIN = 10 MHz, unless otherwise stated 14 Spectral Response @ fIN = 10 MHz Spectral Response @ fIN = 29 MHz Figure 26. Figure 27. Spectral Response @ fIN = 75 MHz Spectral Response @ fIN = 98.9 MHz Figure 28. Figure 29. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 ADC08L060 www.ti.com SNAS167G - MAY 2002 - REVISED MARCH 2013 FUNCTIONAL DESCRIPTION The ADC08L060 uses a unique architecture that achieves over 7 effective bits at input frequencies up to and beyond Nyquist. The analog input signal that is within the voltage range set by VRT and VRB is digitized to eight bits. Input voltages below VRB will cause the output word to consist of all zeroes. Input voltages above VRT will cause the output word to consist of all ones. Incorporating a switched capacitor bandgap, the ADC08L060 exhibits a power consumption that is proportional to frequency, limiting power consumption to what is needed at the clock rate that is used. This and its excellent performance over a wide range of clock frequencies makes it an ideal choice as a single ADC for many 8-bit needs. Data is acquired at the rising edge of the clock and the digital equivalent of that data is available at the digital outputs 5 clock cycles plus tOD later. The ADC08L060 will convert as long as an adequate clock signal is present at pin 24. The output coding is straight binary. The device is in the active state when the Power Down pin (PD) is low. When the PD pin is high, the device is in the power down mode, where the output pins hold the last conversion before the PD pin went high and the device consumes about 1.4 mW. Holding the clock input low will further reduce the power consumption in the power down mode to about 1 mW APPLICATION INFORMATION REFERENCE INPUTS The reference inputs VRT and VRB are the top and bottom of the reference ladder, respectively. Input signals between these two voltages will be digitized to 8 bits. External voltages applied to the reference input pins should be within the range specified in the Operating Ratings table. Any device used to drive the reference pins should be able to source sufficient current into the VRT pin and sink sufficient current from the VRB pin to keep these voltages stable. Chok e +3V 10 PF + 0.1 PF 1 6 +3V 7 24.9 1 % 1.5V, nominal + 0.1 PF 34.8 1 % 0.1 PF VIN 0.1 PF 18 R GND D7 D6 D5 D4 D3 D2 D1 D0 VR 3 10 PF VD VA VIN T + 10 PF 12 4 + 10 PF 9 0.1 PF 13 14 15 16 19 20 21 22 10 VRB 23 PD 2 A. AGN D 5 8 11 DR CLK GND 17 24 Because of the ladder and external resistor tolerances, the reference voltage of this circuit can vary too much for some applications. Figure 30. Simple, Low Component Count Reference Biasing Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 15 ADC08L060 SNAS167G - MAY 2002 - REVISED MARCH 2013 www.ti.com The reference bias circuit of Figure 30 is very simple and the performance is adequate for many applications. However, circuit tolerances will lead to a wide reference voltage range. Better reference stability can be achieved by driving the reference pins with low impedance sources. The circuit of Figure 31 will allow a more accurate setting of the reference voltages. The upper amplifier must be able to source the reference current as determined by the value of the reference resistor and the value of (VRT VRB). The lower amplifier must be able to sink this reference current. Both should be stable with a capacitive load. The LM8272 was chosen because of its rail-to-rail input and output capability, its high current output and its ability to drive large capacitance loads. Of course, the divider resistors at the amplifier input could be changed to suit your reference voltage needs, or the divider can be replaced with potentiometers for precise settings. The bottom of the ladder (VRB) may simply be returned to ground if the minimum input signal excursion is 0V. Be sure that the driving source can source sufficient current into the VRT pin and sink enough current from the VRB pin to keep these pins stable. VRT should always be more positive than VRB by the minimum VRT - VRB difference in the Electrical Characteristics table to minimize noise. Furthermore, the difference between VRT and VRB should not exceed the maximum value specified in the Electrical Characteristics table to avoid signal distortion. The VRM pin is the center of the reference ladder and should be bypassed to a quiet point in the analog ground plane with a 0.1 F capacitor. DO NOT allow this pin to float. +3V Choke 10 PF + 10 PF 0.1 PF 3 8 + 2 1 1 4 12 1/2 LM8272 VIN - 0.1 PF 18 VA 6 DR VD 7 4 0.1 PF VIN GND 0.01 PF 3 VRT 1 PF 4.7k 9 1.62k ADC08L060 0.1 PF 4.7k 10 D7 D6 D5 D4 D3 D2 D1 D0 13 14 15 16 19 20 21 22 VRB 1 PF 0.1 PF 10 PF +3V 1 PF 604: LM4040-2.5 + + 470: 0.01 PF 6 5 + 7 23 PD AGND 1/2 LM8272 2 5 8 11 DR GND CLK 17 24 309: A. Driving the reference to force desired values requires driving with a low impedance source. Figure 31. Setting of Reference Voltages THE ANALOG INPUT The analog input of the ADC08L060 is a switch followed by an integrator. The input capacitance changes with the clock level, appearing as 3 pF when the clock is low, and 4 pF when the clock is high. The sampling nature of the analog input causes current spikes that result in voltage spikes at the analog input pin. Any circuit used to drive the analog input must be able to drive that input and to settle within the clock low time. The LMH6702 has been found to be a good amplifier to drive the ADC08L060. Figure 32 shows an example of an input circuit using the LMH6702. Any input amplifier should incorporate some gain as operational amplifiers exhibit better phase margin and transient response with gains above 2 or 3 than with unity gain. If an overall gain of less than 3 is required, attenuate the input and operate the amplifier at a higher gain, as shown in Figure 32. 16 Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 ADC08L060 www.ti.com SNAS167G - MAY 2002 - REVISED MARCH 2013 The RC at the amplifier output filters the clock rate energy that comes out of the analog input due to the input sampling circuit. The optimum time constant for this circuit depends not only upon the amplifier and ADC, but also on the circuit layout and board material. A resistor value should be chosen between 10 and 47 and the capacitor value chose according to the formula (6) This will provide optimum SNR performance. Best THD performance is realized when the capacitor and resistor values are both zero. To optimize SINAD, reduce the capacitor value until SINAD performance is optimized. That is, until SNR = -THD. This value will usually be in the range of 20& to 65% of the value calculated with the above formula. An accurate calculation is not possible because of the board material and layout dependence. The circuit of Figure 32 has both gain and offset adjustments. If you eliminate these adjustments normal circuit tolerances may result in signal clipping unless care is exercised in the worst case analysis of component tolerances and the input signal excursion is appropriately limited to account for the worst case conditions. Choke +3V 200 - 10 240 1 47 LMH6702 + 100 47 51 pF 6 7 4 12 VIN VDR VIN GND D7 D6 D5 D4 D3 D2 D1 D0 VRT 3 * * 2.7k 9 VRM +3V 1k 1k Offset Adjust -3V to -5V 0.1 PF 18 VA 0.1 PF 0.33 PF 13 14 15 16 19 20 21 22 10 VRB 23 17 DR GND PD *URXQG FRQQHFWLRQV PDUNHG ZLWK * should enter the ground plane at a common point. A. 10 PF 0.1 PF 12 * + 10 PF 0.1 PF Gain Adjust Signal Input + +5V CLK 24 AGND 2 5 7 8 11 The input amplifier should incorporate some gain for best performance (see text). Figure 32. Input Amplifier POWER SUPPLY CONSIDERATIONS A/D converters draw sufficient transient current to corrupt their own power supplies if not adequately bypassed. A 10 F tantalum or aluminum electrolytic capacitor should be placed within an inch (2.5 cm) of the A/D power pins, with a 0.1 F ceramic chip capacitor placed within one centimeter of the converter's power supply pins. Leadless chip capacitors are preferred because they have low lead inductance. While a single voltage source is recommended for the VA and VDR supplies of the ADC08L060, these supply pins should be well isolated from each other to prevent any digital noise from being coupled into the analog portions of the ADC. A choke or 27 resistor is recommended between these supply lines with adequate bypass capacitors close to the supply pins. As is the case with all high speed converters, the ADC08L060 should be assumed to have little power supply rejection. None of the supplies for the converter should be the supply that is used for other digital circuitry in any system with a lot of digital power being consumed. The ADC supplies should be the same supply used for other analog circuitry. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 17 ADC08L060 SNAS167G - MAY 2002 - REVISED MARCH 2013 www.ti.com No pin should ever have a voltage on it that is in excess of the supply voltage or below ground by more than 300 mV, not even on a transient basis. This can be a problem upon application of power and power shut-down. Be sure that the supplies to circuits driving any of the input pins, analog or digital, do not come up any faster than does the voltage at the ADC08L060 power pins. THE DIGITAL INPUT PINS The ADC08L060 has two digital input pins: The PD pin and the Clock pin. The PD Pin The Power Down (PD) pin, when high, puts the ADC08L060 into a low power mode where power consumption is reduced to 1.4 mW with the clock running, or to about 1 mW with the clock held low. Output data is valid and accurate about 1 microsecond after the PD pin is brought low. The digital output pins retain the last conversion output code when either the clock is stopped or the PD pin is high. The ADC08L060 Clock Although the ADC08L060 is tested and its performance is ensured with a 60 MHz clock, it typically will function well with clock frequencies from 10 MHz to 80 MHz. Clock Duty Cycle The low and high times of the clock signal can affect the performance of any A/D Converter. Because achieving a precise duty cycle is difficult, the ADC08L060 is designed to maintain performance over a range of duty cycles. While it is specified and performance is ensured with a 50% clock duty cycle and 60 Msps, ADC08L060 performance is typically maintained with clock high and low times of 0.83 ns, corresponding to a clock duty cycle range of 5% to 95% with a 60 MHz clock. Note that minimum low and high times may not be simultaneously asserted. Clock Line Termination The CLOCK line should be series terminated at the clock source in the characteristic impedance of that line. If the clock line is longer than (7) where tr is the clock rise time and tprop is the propagation rate of the signal along the trace. The CLOCK pin should be a.c. terminated with a series RC to ground such that the resistor value is equal to the characteristic impedance of the clock line and the capacitor value is (8) where "L" is the line length in inches and ZO is the characteristic impedance of the clock line. Typical tPROP is about 150 ps/inch on FR-4 board material. For FR-4 board material, the value of C becomes (9) This termination should be located as close as possible to, but within one centimeter of, the ADC08L060 clock pin. LAYOUT AND GROUNDING Proper grounding and proper routing of all signals are essential to ensure accurate conversion. A combined analog and digital ground plane should be used. Since digital switching transients are composed largely of high frequency components, total ground plane copper weight will have little effect upon the logic-generated noise because of the skin effect. Total surface area is more important than is total ground plane volume. Capacitive coupling between the typically noisy digital circuitry and the sensitive analog circuitry can lead to poor performance that may seem impossible to isolate and remedy. The solution is to keep the analog circuitry well separated from the digital circuitry. 18 Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 ADC08L060 www.ti.com SNAS167G - MAY 2002 - REVISED MARCH 2013 The DR GND connection to the ground plane should not use the same feedthrough used by other ground connections. High power digital components should not be located on or near a straight line between the ADC or any linear component and the power supply area as the resulting common return current path could cause fluctuation in the analog input "ground" return of the ADC. Keeping analog and digital return (ground) currents separate from each other will improve system noise performance. Two methods may be used to do this. Use of traces rather than a solid plane to route power to all components will accomplish this because return currents follow the path of the outgoing currents. However, the advantage of the distributed capacitance of a power plane and a ground plane is lost. Analog and digital power should be routed as far from each other as is practical. The analog power trace should also be routed away from digital areas of the board. The use of power and ground planes in adjacent layers will provide distributed capacitance for a low impedance power distribution system and better system noise performance. The use of separate analog and digital power planes, both in the same PC board layer, and the use of a single, non-split ground plane will keep analog and digital currents separated from each other. Of course, locate all analog circuitry and traces over the analog power plane and the digital circuitry and traces over the digital power plane. To minimize RFI/EMI, give proper attention to any lines crossing the analog/digital power plane boundary. Noise performance is also enhanced by driving a single gate with each ADC output pin and locating the gate as close as possible to the ADC output. Inserting a 47 resistor in series with the ADC digital output pins will also help reduce ADC noise. Be sure to keep the resistors as close to the ADC output pins as possible. Eliminating ground plane copper beneath the ADC output lines can also help ADC noise performance, but could produce unacceptable radiation from the board. Analog and digital circuitry should be kept well away from each other. Especially troublesome is high power digital components such as processors and large PLDs. Switch mode power supplies, including capacitive DCDC converters, can cause noise problems with high speed ADCs. Keep such components well away from ADCs and low level analog signal areas. Such components should be located as close to the power supply as possible and should not be in the path of analog signal or power supply currents. Digital circuits create substantial supply and ground current transients. The noise thus generated could have significant impact upon system noise performance. The best logic family to use in systems with A/D converters is one that employs non-saturating transistor designs, or has low noise characteristics, like the 74LS and the 74AC(T)Q families. The worst noise generators are logic families that draw the largest supply current transients during clock or signal edges, like the 74HC, 74F and 74AC(T) families. Since digital switching transients are composed largely of high frequency components, total ground plane copper weight will have little effect upon logic-generated noise. This is because of the skin effect. Total surface area is more important than is total ground plane volume. Clock lines should be isolated from ALL other lines, analog AND digital. Even the generally accepted 90 crossing should be avoided as even a little coupling can cause problems at high frequencies. Best performance at high frequencies is obtained with a straight signal path. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 19 ADC08L060 SNAS167G - MAY 2002 - REVISED MARCH 2013 www.ti.com Single Ground Plane ADC Clock Source Locate driving amplifier near ADC input pin RF Locate Clock Source near ADC clock pin RIN R C LMH6702 ADC 08L060 Locate power supply on the digital side of the ADC Figure 33. Layout Example The analog input should be isolated from noisy signal traces to avoid coupling of spurious signals into the input. Any external component (e.g., a filter capacitor) connected between the converter's input and ground should be connected to a very clean point in the ground plane. Figure 33 gives an example of a suitable layout. All analog circuitry (input amplifiers, filters, reference components, etc.) should be placed together away from any digital components. DYNAMIC PERFORMANCE The ADC08L060 is a.c. tested and its dynamic performance is ensured. To meet the published specifications, the clock source driving the CLK input should exhibit less than 10 ps (rms) of jitter. For best a.c. performance, isolating the ADC clock from any digital circuitry should be done with adequate buffers, as with a clock tree. See Figure 34. It is good practice to keep the ADC clock line as short as possible and to keep it well away from any other signals. Other signals can introduce jitter into the clock signal. The clock signal can also introduce noise into the analog path. Figure 34. Isolating the ADC Clock from Digital Circuitry COMMON APPLICATION PITFALLS Driving the inputs (analog or digital) beyond the power supply rails. For proper operation, all inputs should not go more than 300 mV below the ground pins or 300 mV above the supply pins. Exceeding these limits on even a transient basis may cause faulty or erratic operation. It is not uncommon for high speed digital circuits (e.g., 74F and 74AC devices) to exhibit undershoot that goes more than a volt below ground. A 51 resistor in series with the offending digital input will usually eliminate the problem. Care should be taken not to overdrive the inputs of the ADC08L060. Such practice may lead to conversion inaccuracies and even to device damage. 20 Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 ADC08L060 www.ti.com SNAS167G - MAY 2002 - REVISED MARCH 2013 Attempting to drive a high capacitance digital data bus. The more capacitance the output drivers must charge for each conversion, the more instantaneous digital current is required from VDR and DR GND. These large charging current spikes can couple into the analog section, degrading dynamic performance. Buffering the digital data outputs (with a 74F541, for example) may be necessary if the data bus capacitance exceeds 5 pF. Dynamic performance can also be improved by adding 100 series resistors at each digital output, reducing the energy coupled back into the converter input pins. Using an inadequate amplifier to drive the analog input. As explained in Section 2.0, the capacitance seen at the input alternates between 3 pF and 4 pF with the clock. This dynamic capacitance is more difficult to drive than is a fixed capacitance, and should be considered when choosing a driving device. Driving the VRT pin or the VRB pin with devices that can not source or sink the current required by the ladder. As mentioned in Section 1.0, care should be taken to see that any driving devices can source sufficient current into the VRT pin and sink sufficient current from the VRB pin. If these pins are not driven with devices than can handle the required current, these reference pins will not be stable, resulting in a reduction of dynamic performance. Using a clock source with excessive jitter, using an excessively long clock signal trace, or having other signals coupled to the clock signal trace. This will cause the sampling interval to vary, causing excessive output noise and a reduction in SNR performance. The use of simple gates with RC timing is generally inadequate as a clock source. Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 21 ADC08L060 SNAS167G - MAY 2002 - REVISED MARCH 2013 www.ti.com REVISION HISTORY Changes from Revision F (March 2013) to Revision G * 22 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 21 Submit Documentation Feedback Copyright (c) 2002-2013, Texas Instruments Incorporated Product Folder Links: ADC08L060 PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) ADC08L060CIMT NRND TSSOP PW 24 61 TBD Call TI Call TI -40 to 85 ADC08L060 CIMT ADC08L060CIMT/NOPB ACTIVE TSSOP PW 24 61 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 ADC08L060 CIMT ADC08L060CIMTX/NOPB ACTIVE TSSOP PW 24 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 ADC08L060 CIMT (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing ADC08L060CIMTX/NOPB TSSOP PW 24 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 16.4 Pack Materials-Page 1 6.95 B0 (mm) K0 (mm) P1 (mm) 8.3 1.6 8.0 W Pin1 (mm) Quadrant 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) ADC08L060CIMTX/NOPB TSSOP PW 24 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated