Aluminum Electrolytic Capacitors SG series High ripple current, ultra low impedance at high frequency range. Long life. RoHS Compliance SPECIFICATIONS Items Characteristics Capacitance Tolerance 20%(120Hz20) Operating Temperature Range -40 ~ +105 Rated Voltage Range 6.3 ~ 50VDC Leakage Current I 0.01CV or 3 (A) which is greater. ( After 2 minutes application of DC rated voltage, at 20 ) Measurement Frequency: 120Hz. Temperature: 20 Dissipation Factor ( tan ) Load Life 6.3 Standards 16 25 35 50 Rated Voltage(V) 6.3 10 16 25 35 50 Z(-25) Z(20) 2 2 2 2 2 2 Z(-40) Z(20) 3 3 3 3 3 3 The following specifications shall be satisfied when the capacitors are restored to 20 after subjected to DC voltage with the rated ripple currrent is applied for 5,000 hours (D6.3:2,000 hours;D=8:3,000 hours;D=10:4,000 hours) at 105. Capacitance Change Within 25% of Initial Value tan Shelf Life 10 SG Low Temperature Stability Impedance Ratio(Max) () Rated Voltage(V) tan (Max) 0.15 0.12 0.10 0.09 0.08 0.07 When nominal capacitance over 1000F, tan shall be added 0.02 to the listed value with increase of every 1000F. Measurement Frequency: 120Hz. 200% or less of Initial Specified Value Leakage Current Initial Specified Value or less The following specifications shall be satisfied when the capacitors are restored to 20 after exposing them for 1,000 hours 105 without voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to them 4.1 of JIS C5101-4. Capacitance Change Within 20% of Initial Value tan 200% or less of Initial Specified Value Leakage Current Initial Specified Value or less JIS C 5101-4 (IEC 60384) Frequency Coefficient of Permissible Ripple Current Capacitance (F) 33 47 ~ 330 470 ~ 1000 1200 ~ 6800 50 0.45 0.60 0.65 0.75 120 0.55 0.70 0.75 0.80 Frequency (Hz) 1K 0.75 0.85 0.90 0.95 10K 0.90 0.95 0.98 1.00 100K 1.00 1.00 1.00 1.00 The endurance of capacitors is reduced with internal heating produced by ripple current at the rate of halving the lifetime with every 5 rise. When long life performance is required in actual use , the rms ripple current has to be reduced. 163 Aluminum Electrolytic Capacitors SG series DIMENSIONS(mm) D P d 5 2.0 0.5 6.3 2.5 0.5 8 3.5 0.5 10 5.0 0.6 13 5.0 0.6 16 7.5 0.8 STANDARD RATINGS Cap (F) V Item 56 100 120 150 220 330 R.C. 10 IMP DxL 05x11 05x11 250 0.300 6.3x11. 405 0.130 08x12 760 0.072 470 560 680 820 08x16 995 0.056 1000 10x13 1030 0.053 1200 08x20 10x16 10x20 10x25 1250 1430 1820 2150 0.041 0.038 0.023 0.022 SG 1500 2200 (L 16) 1.0 (L 16) 2.0 DxL(mm) ; R.C.(mA rms) at 105 100KHz ; IMP ( max)at 20 100KHz. 6.3 DxL R.C. 16 IMP 13x21 2360 0.021 3900 13x25 2770 0.018 4700 13x30 13x35 16x22 16x26 3290 3350 3400 3460 0.016 0.015 0.018 0.016 5600 6800 Cap (F) V Item 22 33 47 56 68 100 120 150 180 220 270 330 470 560 680 R.C. IMP 250 0.300 6.3x11. 405 0.130 760 0.130 08x12 08x16 10x13 760 995 1030 0.072 0.056 0.053 0.130 0.085 08x12 760 0.072 08x16 10x13 995 1030 0.056 0.053 08x20 10x16 1250 1430 0.041 0.038 08x20 10x16 1250 1430 0.041 0.038 10x20 1820 0.023 10x20 1820 0.023 10x25 2150 0.022 10x25 13x21 2150 2360 0.022 0.021 13x25 13x30 16x22 13x35 2770 3290 3140 3400 0.018 0.016 0.018 0.015 13x21 13x25 13x30 16x22 13x35 2360 2770 3140 3290 3400 0.021 0.018 0.016 0.018 0.015 16x26 3460 0.016 16x26 3460 0.016 0.072 08x16 10x13 08x20 10x16 995 1030 1250 1430 0.056 0.053 0.041 0.038 10x20 1820 0.023 DxL R.C. 50 IMP 05x11 250 0.300 6.3x11. 405 0.130 DxL R.C. IMP 05x11 238 0.340 6.3x11. 385 0.140 08x12 08x16 10x13 08x20 724 950 979 1190 0.074 0.061 0.061 0.046 10x16 1370 0.042 10x20 1580 0.030 08x12 760 0.072 08x16 10x13 08x20 995 1030 1250 0.056 0.053 0.041 10x16 1430 0.038 10x25 1870 0.028 10x20 1820 0.023 13x21 2050 0.027 10x25 13x21 2150 2360 0.022 0.021 13x25 13x30 13x35 16x22 16x26 2410 2860 2960 2730 3010 0.023 0.021 0.019 0.023 0.021 10x25 2150 0.022 13x21 2450 0.020 13x21 2360 0.021 1200 13x21 2360 0.021 1500 13x25 13x30 16x22 13x35 16x26 2770 3140 3290 3400 3460 0.018 0.016 0.018 0.015 0.016 13x25 13x30 16x22 13x35 2770 3140 3290 3400 0.018 0.016 0.018 0.015 16x26 3460 0.016 13mm may be replaced by 12.5mm upon customer's request. 164 405 405 600 820 2200 2700 6.3x11. 6.3x11.. 08x12. 1000 1800 0.300 35 05x11 08x12 IMP 250 0.300 25 DxL R.C. 250 . 2700 3300 DxL 05x11