Thyristors Surface Mount > 200 - 600V > C106 Series C106 Series Pb Description Glassivated PNPN devices designed for high volume consumer applications such as temperature, light, and speed control; process and remote control, and warning systems where reliability of operation is important. Features * Glassivated Surface for Reliability and Uniformity * Power Rated at Economical Prices * Practical Level Triggering and Holding Characteristics * Flat, Rugged, Thermopad Construction for Low Thermal Resistance, High Heat Dissipation and Durability * Sensitive Gate Triggering * These are Pb-Free Devices Functional Diagram Pin Out G,3 A,2 3 2 1 TO 225AA CASE 77 STYLE 2 K,1 Additional Information Datasheet Resources Samples (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/11/19 Thyristors Surface Mount > 200 - 600V > C106 Series Maximum Ratings (TJ = 25C unless otherwise noted) Rating Peak Repetitive Off-State Voltage (Sine Wave, 50-60 Hz, RGK = 1 K, TC = -40 to 110C) C106B C106D, C106D1* C106M On-State RMS Current (180 Conduction Angles, TC = 80C) Symbol Value Unit VDRM, VRRM 200 400 600 V IT 4.0 A (RMS) Average On-State Current (180 Conduction Angles, TC = 80C) IT(AV) 2.55 A Peak Non-Repetitive Surge Current (1/2 Cycle, Sine Wave, 60 Hz, TJ = +25C) ITSM 20 A Circuit Fusing Considerations (t = 8.3 ms) I2t 1.65 A2s Forward Peak Gate Current (Pulse Width 1.0 sec, TC = 80C) IGM 0.2 A Forward Peak Gate Power (Pulse Width 1.0 sec, TC = 80C) PGM 0.5 W Forward Average Gate Power (Pulse Width 1.0 sec, TC = 80C) PG(AV) 0.1 W Operating Junction Temperature Range TJ -40 to +110 C Storage Temperature Range Tstg -40 to +150 C _ 6.0 in. lb. Mounting Torque (Note 2) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. 2. Torque rating applies with use of torque washer (Shakeproof WD19523 or equivalent). Mounting Torque in excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance. Main terminal 2 and heat-sink contact pad are common. Thermal Characteristics Rating Symbol Value Unit RJC RJA 3.0 75 C/W TL 260 C Junction-to-Case (AC) Junction-to-Ambient Thermal Resistance, Maximum Lead Temperature for Soldering Purposes, 1/8" from case for 10 seconds Electrical Characteristics - OFF (TJ = 25C unless otherwise noted) Characteristic Peak Repetitive Forward or Reverse Blocking Current (VAK = Rated VDRM or VRRM, RGK = 1 k) Symbol TJ = 25C TJ = 110C IDRM, IRRM Min Typ Max Unit _ _ 10 A - - 100 A Typ Max Unit V Electrical Characteristics - ON (TJ = 25C unless otherwise noted) Characteristic Peak Forward On-State Voltage (Note 3) (ITM = 4 A) Gate Trigger Current (Continuous dc) (VD = 12 V, RL = 100 , All Quadrants) TJ = 25C TJ = -40C Peak Reverse Gate Voltage (IGR = 10 A) Gate Trigger Voltage (Continuous dc) (VD = 12 Vdc, RL = 100 , TC = 25C) Holding Current (VD = 12 Vdc) (Initiating Current = 20 mA, RGK = 1 k) Min VTM - - 2.2 _ 15 200 - 35 500 IGT VGRM TJ = 25C TJ = -40C Gate Non-Trigger Voltage (Continuous dc) (Note 4) (VAK = 12 V, RL = 100 (VAK = 12 V, RL = 100 , TJ = 110C), TJ = 110C) Latching Current (VAK = 12 V, IG = 20 mA, RGK = 1 k) Symbol VGT VGD TJ = 25C TJ = -40C IL TJ = 25C TJ = -40C TJ = +110C IH - - 6.0 0.4 0.60 0.8 0.5 0.75 1.0 0.2 _ _ _ 0.20 5.0 - 0.35 7.0 _ 0.19 3.0 _ 0.33 6.0 _ 0.07 2.0 A V V V mA mA (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/11/19 Thyristors Surface Mount > 200 - 600V > C106 Series Dynamic Characteristics Characteristic Critical Rate-of-Rise of Off State Voltage (VAK = Rated VDRM, Exponential Waveform, RGK = 1k,TJ = 110C) Symbol Min Typ Max Unit dv/dt - 8.0 - V/s 3. Pulse Test: Pulse Width 2.0 ms, Duty Cycle 2%. 4. RGK is not included in measurement. Voltage Current Characteristic of SCR Symbol Parameter VDRM Peak Repetitive Forward Off State Voltage IDRM Peak Forward Blocking Current VRRM Peak Repetitive Reverse Off State Voltage IRRM Peak Reverse Blocking Current VTM Maximum On State Voltage IH Holding Current +C urrent V TM on stat e I RR M at V RR M IH Quadrant 3 Main Terminal 2 Quadrant 1 Main Terminal 2 + IH off stat e +V oltage I DR M at V DR M V TM (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/11/19 Thyristors Surface Mount > 200 - 600V > C106 Series Figure 1. Average Current Derating Figure 2. Maximum On-State Power Dissipation Figure 3. Typical Gate Trigger Current vs. Junction Temp Figure 4. Typical Holding Current vs. Junction Temp Figure 5. Typical Gate Trigger Voltage vs. Junction Temp Figure 5. Typical Latching Current vs. Junction Temp (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/11/19 Thyristors Surface Mount > 200 - 600V > C106 Series Part Marking System Dimensions A1 A TO 225AA CASE 077 STYLE 2 Q E OP D PIN4 BACKSIDE TAB 1 2 3 L1 1. Cathode 2. Anode 3. Gate L Y M A XX C106xx xx G b2 x2 b e Dim e C106xxG YMAXX =Year =Month =Assembly Site =Lot Serial Code =Device Code =B, D, D1, M, M1 =Pb-Free Package c Inches Pin Assignment Millimeters Min Max Min Max 1 Cathode A 0.102 0.110 2.60 2.80 2 Anode A1 0.047 0.055 1.20 1.40 3 Gate b 0.028 0.034 0.70 0.86 b2 0.028 0.034 0.70 0.86 c 0.019 0.022 0.49 0.57 D 0.417 0.449 10.60 11.40 E 0.291 0.323 7.40 8.20 e 0.090 TYP L 0.551 L1 0.091 P 0.118 Q 0.142 0.157 Device Shipping TO225AA (Pb-Free) 2500 Units/Box C106BG C106D1G* 14.00 16.00 0.106 2.30 2.70 C106MG 0.134 3.00 3.40 C106M1G* 3.60 4.00 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 077-01 THRU -08 OBSOLETE, NEW STANDARD 077-09. Package C106DG 2.29 TYP 0.630 Ordering Information *D1 signifies European equivalent for D suffix and M1 signifies European equivalent for M suffix. Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/11/19