© 2019 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 06/11/19
Thyristors
Surface Mount > 200 - 600V > C106 Series
• Glassivated Surface for
Reliability and Uniformity
• Power Rated at
Economical Prices
• Practical Level
Triggering and Holding
Characteristics
• Flat, Rugged, Thermopad
Construction for Low
Thermal Resistance, High
Heat Dissipation and
Durability
• Sensitive Gate Triggering
These are Pb−Free
Devices
Features
Glassivated PNPN devices designed for high volume
consumer applications such as temperature, light, and
speed control; process and remote control, and warning
systems where reliability of operation is important.
Description
C106 Series
Functional Diagram
Additional Information
Samples
Resources
Datasheet
Pin Out
TO 225AA
CASE 77
STYLE 2
1
2
3
Pb
K,1
G,3
A,2
© 2019 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 06/11/19
Thyristors
Surface Mount > 200 - 600V > C106 Series
Rating Symbol Value Unit
Peak Repetitive Off−State Voltage
(Sine Wave, 50−60 Hz, RGK = 1 K,
TC = −40° to 110°C)
C106B
C106D, C106D1*
C106M
VDRM,
VRRM
200
400
600 V
On-State RMS Current (180° Conduction Angles, TC = 80°C) IT (RMS) 4.0 A
Average On−State Current (180° Conduction Angles, TC = 80°C) IT(AV) 2.55 A
Peak Non-Repetitive Surge Current
(1/2 Cycle, Sine Wave, 60 Hz, TJ = +25°C) ITSM 20 A
Circuit Fusing Considerations (t = 8.3 ms) I2t 1.65 A2s
Forward Peak Gate Current
(Pulse Width 1.0 sec, TC = 80°C) IGM 0.2 A
Forward Peak Gate Power (Pulse Width ≤ 1.0 µsec, TC = 80°C) PGM 0.5 W
Forward Average Gate Power (Pulse Width ≤ 1.0 µsec, TC = 80°C) PG(AV) 0.1 W
Operating Junction Temperature Range TJ-40 to +110 °C
Storage Temperature Range Tstg -40 to +150 °C
Mounting Torque (Note 2) _ 6.0 in. lb.
Maximum Ratings (TJ = 25°C unless otherwise noted)
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied.
Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
1. VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative
potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded.
2. Torque rating applies with use of torque washer (Shakeproof WD19523 or equivalent). Mounting Torque in excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance.
Main terminal 2 and heat-sink contact pad are common.
Thermal Characteristics
Rating Symbol Value Unit
Thermal Resistance, Junction−to−Case (AC)
Junction−to−Ambient RƟJC
RƟJA
3.0
75 °C/W
Maximum Lead Temperature for Soldering Purposes, 1/8” from case for
10 seconds TL260 °C
Electrical Characteristics - OFF (TJ = 25°C unless otherwise noted)
Electrical Characteristics - ON (TJ = 25°C unless otherwise noted)
Characteristic Symbol Min Ty p Max Unit
Peak Repetitive Forward or Reverse Blocking Current
(VAK = Rated VDRM or VRRM, RGK = 1 Ωk)
TJ = 25°C IDRM, IRRM
_ _ 10 μA
TJ = 110°C 100 µA
Characteristic Symbol Min Ty p Max Unit
Peak Forward On-State Voltage (Note 3) (ITM = 4 A) VTM 2.2 V
Gate Trigger Current (Continuous dc)
(VD = 12 V, RL = 100 Ω, All Quadrants)
TJ = 25°C IGT
_15 200 µA
TJ = -40°C 35 500
Peak Reverse Gate Voltage (IGR = 10 µA) VGRM 6.0 V
Gate Trigger Voltage (Continuous dc)
(VD = 12 Vdc, RL = 100 Ω, TC = 25°C)
TJ = 25°C VGT
0.4 0.60 0.8 V
TJ = -40°C 0.5 0.75 1.0
Gate Non−Trigger Voltage (Continuous dc) (Note 4)
(VAK = 12 V, RL = 100
(VAK = 12 V, RL = 100 , TJ = 110°C), TJ = 110°C) VGD 0.2 _ _ V
Latching Current
(VAK = 12 V, IG = 20 mA, RGK = 1 kΩ)
TJ = 25°C IL
_ 0.20 5.0 mA
TJ = -40°C 0.35 7. 0
Holding Current
(VD = 12 Vdc)
(Initiating Current = 20 mA, RGK = 1 kΩ)
TJ = 25°C
IH
_ 0.19 3.0
mA
TJ = -40°C _ 0.33 6.0
TJ = +110°C _ 0.07 2.0
© 2019 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 06/11/19
Thyristors
Surface Mount > 200 - 600V > C106 Series
Dynamic Characteristics
Characteristic Symbol Min Ty p Max Unit
Critical Rate-of-Rise of Off State Voltage
(VAK = Rated VDRM, Exponential Waveform, RGK = 1kΩ,TJ = 110°C) dv/dt 8.0 V/µs
3. Pulse Test: Pulse Width ≤ 2.0 ms, Duty Cycle ≤ 2%.
4. RGK is not included in measurement.
Voltage Current Characteristic of SCR
Symbol Parameter
VDRM Peak Repetitive Forward Off State Voltage
IDRM Peak Forward Blocking Current
VRRM Peak Repetitive Reverse Off State Voltage
IRRM Peak Reverse Blocking Current
VTM Maximum On State Voltage
IHHolding Current
+C urrent
+V oltage
VTM
IH
IDR M at VDR M
on stat e
off stat e
IRR M at VRR M
Quadrant 1
Main Terminal 2 +
Quadrant 3
Main Terminal 2 VTM
IH
© 2019 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 06/11/19
Thyristors
Surface Mount > 200 - 600V > C106 Series
Figure 1. Average Current Derating
Figure 3. Typical Gate Trigger Current vs. Junction Temp
Figure 5. Typical Gate Trigger Voltage vs. Junction Temp
Figure 2. Maximum On-State Power Dissipation
Figure 4. Typical Holding Current vs. Junction Temp
Figure 5. Typical Latching Current vs. Junction Temp
© 2019 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 06/11/19
Thyristors
Surface Mount > 200 - 600V > C106 Series
Dimensions Part Marking System
Pin Assignment
1 Cathode
2 Anode
3 Gate
Ordering Information
Device Package Shipping
C106BG
TO225AA
(Pb-Free) 2500 Units/Box
C106DG
C106D1G*
C106MG
C106M1G*
*D1 signifies European equivalent for D suffix and M1 signifies
European equivalent for M suffix.
TO 225AA
CASE 077
STYLE 2
1. Cathode
2. Anode
3. Gate
Dim Inches Millimeters
Min Max Min Max
A 0.102 0.110 2.60 2.80
A1 0.047 0.055 1.20 1.40
b 0.028 0.034 0.70 0.86
b2 0.028 0.034 0.70 0.86
c 0.019 0.022 0.49 0.57
D 0.417 0.449 10.60 11.40
E 0.291 0.323 7.40 8.20
e0.090 TYP 2.29 TYP
L 0.551 0.630 14.00 16.00
L1 0.091 0.106 2.30 2.70
P 0.118 0.134 3.00 3.40
Q 0.142 0.157 3.60 4.00
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications.
Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics.
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. 077-01 THRU -08 OBSOLETE, NEW STANDARD 077-09.
123
E
Q
ØP
D
L1
e e c
b2 x2
L
A1
A
PIN4
BACKSIDE TAB
b
C106xxG
YMAXX
Y =Year
M =Month
A =Assembly Site
XX =Lot Serial Code
C106xx =Device Code
xx =B, D, D1, M, M1
G =Pb-Free Package