Low Voltage ORing FET Controller ISL6146 Features The ISL6146 represents a family of ORing MOSFET controllers capable of ORing voltages from 1V to 18V. Together with suitably sized N-channel power MOSFETs, the ISL6146 increases power distribution efficiency when replacing a power ORing diode in high current applications. It provides gate drive voltage for the MOSFET(s) with a fully integrated charge pump. * ORing Down to 1V and Up to 20V with ISL6146A, ISL6146B, ISL6146D and ISL6146E The ISL6146 allows users to adjust with external resistor(s) the VOUT - VIN trip point, which adjusts the control sensitivity to system power supply noise. An open drain FAULT pin will indicate if a conditional or FET fault has occurred. The ISL6146A and ISL6146B are optimized for very low voltage operation, down to 1V with an additional independent bias of 3V or greater. The ISL6146C provides a voltage compliant mode of operation down to 3V with programmable Undervoltage Lock Out and Overvoltage Protection threshold levels The ISL6146D and ISL6146E are like the ISL6146A and ISL6146B respectively but do not have conduction state reporting via the fault output. TABLE 1. KEY DIFFERENCES BETWEEN PARTS IN FAMILY PART NUMBER KEY DIFFERENCES * Programmable Voltage Compliant Operation with ISL6146C * VIN Hot Swap Transient Protection Rating to +24V * High Speed Comparator Provides Fast <0.3s Turn-off in Response to Shorts on Sourcing Supply * Fastest Reverse Current Fault Isolation with 6A Turn-off Current * Very Smooth Switching Transition * Internal Charge Pump to Drive N-channel MOSFET * User Programmable VIN - VOUT Vth for Noise Immunity * Open Drain FAULT Output with Delay - Short between any two of the ORing FET Terminals - GATE Voltage and Excessive FET VDS - Power-Good Indicator (ISL6146C) * MSOP and DFN Package Options Applications * N+1 Industrial and Telecom Power Distribution Systems ISL6146A Separate BIAS and VIN with Active High Enable ISL6146B Separate BIAS and VIN with Active Low Enable * Low Voltage Processor and Memory ISL6146C VIN with OVP/UVLO Inputs * Storage and Datacom Systems ISL6146D ISL6146A wo Conduction Monitor & Reporting ISL6146E ISL6146B wo Conduction Monitor & Reporting + Q1 + VOLTAGE DC/DC (3V - 20V) VIN GATE VOUT BIAS ADJ ISL6146B FLT GND EN Q2 + VOLTAGE DC/DC (3V - 20V) VIN GATE VOUT VOUT BIAS ADJ ISL6146B FLT GND EN - FIGURE 1. TYPICAL APPLICATION July 12, 2012 FN7667.2 1 * Uninterruptable Power Supplies C O M M O N P O W E R GATE FAST OFF, ~200ns FALL TIME ~70ns FROM 20V TO 12.6V ACROSS 57nF GATE OUTPUT SINKING ~ 6A B U S +C O M M O N P O W E R B U S FIGURE 2. ISL6146 GATE HIGH CURRENT PULL-DOWN CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2011, 2012. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. ISL6146 Block Diagram FAULT DIAGNOSTIC 1. VIN - VOUT > 570mV 2. GATE - VIN < 220mV (A,B,C only) Q-PUMP BIAS + VIN VDS FORWARD REGULATOR + - GATE 19mV VOUT REVERSE DETECTION 57mV COMPARATOR + + - EN/EN ENABLE EN ENABLE * 4A + + UVLO 8mA ADJ FLT 3. TEMP > +150C 4. VBIAS < POR (ISL6146A/B/D/E) 5. VIN OR VOUT < POR (ISL6146C) 6. VIN < VOUT 7. Gate to Drain and Gate to Source Shorts HIGH SPEED COMPARATOR + - OVP VREF + ISL6146A/B/D/E + - * Connected to BIAS on ISL6146A/B/D/E VREF Connected to VOUT on ISL6146C ISL6146C Pin Configuration ISL6146A, ISL6146B, ISL6146D, ISL6146E GATE 1 8 VOUT VIN 2 7 ADJ BIAS 3 6 FAULT 4 5 GND EN ISL6146A EN ISL6146B ISL6146 (8 LD MSOP/DFN) TOP VIEW ISL6146C GATE 1 8 VOUT VIN 2 7 ADJ UVLO 3 6 FAULT OVP 4 5 GND EPAD on DFN only, connect to GND Pin Descriptions MSOP/ DFN SYMBOL DESCRIPTION 1 GATE Gate Drive output to the external N-Channel MOSFET generated by the IC internal charge pump. Gate turn-on time is typically <1ms. Allows active control of external N-Channel FET gate to perform ORing function. The GATE drive is between VIN + 7V at VIN = 3.3V and VIN +12V at VIN = 18V. 2 VIN Connected to the sourcing supply side (ORing MOSFET Source), this pin serves as the sense pin to determine the OR'd supply voltage. The ORing MOSFET will be turned off when VIN becomes lower than VOUT by a value more than the externally set threshold or the defaulted internal threshold. Range: 0V to 24V 3 ISL6146A ISL6146B BIAS Primary bias pin. Connected to an independent voltage supply greater than or equal to 3V and greater than VIN. Range: 3.0 to 24V 3 ISL6146C UVLO Programmable UVLO protection to prevent premature turn-on prior to VIN being adequately biased. Range: 0V to 24V 4 ISL6146A EN Active high enable input to turn on the FET. Internally pulled low to GND through 2M. Range: 0V to 24V 4 ISL6146B EN Active low enable input to turn on the FET. Internally pulled high to BIAS through 2M. Range: 0 to 24V 2 FN7667.2 July 12, 2012 ISL6146 Pin Descriptions MSOP/ DFN (Continued) SYMBOL DESCRIPTION 4 ISL6146C OVP Programmable OV protection to prevent continued operation when the monitored voltage is too high. A back-to-back FET configuration must be employed to implement the OVP capability. Range: 0V to 24V 5 GND Chip ground reference. 6 FAULT 7 ADJ Resistor programmable VIN - VOUT Voltage Threshold (Vth) of the High Speed Comparator. This pin is either directly connected to VOUT or can be connected through a 5k to 100k resistor to GND. Allows for adjusting the voltage difference threshold to prevent unintended turn-off of the pass FET due to normal system voltage fluctuations. Range: 0.4 to VOUT 8 VOUT The second sensing node for external FET control and connected to the Load side (ORing MOSFET Drain). This is the common connection point for multiple paralleled supplies. VOUT is compared to VIN to determine when the ORing FET has to be turned off. Range: 0V to 24V PAD Thermal Pad Open-Drain pull-down fault indicating output with internal on chip filtering (TFLT). The ISL6146 fault detection circuitry pulls down this pin to GND as it detects a fault or to a disabled input (EN = `0' or EN = `1'). Different types of faults and their detection mechanisms are discussed in more detail on page 16. These faults include: a. GATE is OFF (GATE < VIN +0.2V) when enabled [this condition is not reported on the ISL6146D and ISL6146E] b. VIN-VOUT > 0.57V when ON. c. FET G-D or G-S or D-S shorts. d. VIN < PORL2H e. VIN < VOUT f. Over-Temperature Range: 0 to VOUT Connect to GND Ordering Information PART NUMBER (Notes 1, 2, 3) PART MARKING ISL6146AFUZ 6146A TEMP RANGE (C) -40 to +125 PACKAGE (Pb-free) 8 Ld MSOP PKG. DWG. # M8.118 ISL6146AFRZ 46AF -40 to +125 8 Ld 3x3 DFN L8.3x3J ISL6146BFUZ 6146B -40 to +125 8 Ld MSOP M8.118 ISL6146BFRZ 46BF -40 to +125 8 Ld 3x3 DFN L8.3x3J ISL6146CFUZ 6146C -40 to +125 8 Ld MSOP M8.118 ISL6146CFRZ 46CF -40 to +125 8 Ld 3x3 DFN L8.3x3J ISL6146DFUZ 6146D -40 to +125 8 Ld MSOP M8.118 ISL6146DFRZ 46DF -40 to +125 8 Ld 3x3 DFN L8.3x3J ISL6146EFUZ 6146E -40 to +125 8 Ld MSOP M8.118 ISL6146EFRZ 46EF -40 to +125 8 Ld 3x3 DFN L8.3x3J ISL6146AEVAL1Z ISL6146A Evaluation Board ISL6146BEVAL1Z ISL6146B Evaluation Board ISL6146CEVAL1Z ISL6146C Evaluation Board ISL6146DEVAL1Z ISL6146D Evaluation Board ISL6146EEVAL1Z ISL6146E Evaluation Board NOTES: 1. Add "-T*" suffix for tape and reel. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see device information page for ISL6146. For more information on MSL please see techbrief TB363. 3 FN7667.2 July 12, 2012 ISL6146 Table of Contents Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Thermal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Recommended Operating Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Typical Performance Curves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Applications Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Power-Up Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Typical Applications Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 ISL6146 Evaluation Platforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Description and Use of the Evaluation Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 L8.3x3J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 M8.118 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4 FN7667.2 July 12, 2012 ISL6146 Absolute Maximum Ratings Thermal Information BIAS, VIN, VOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +24V GATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 40V EN, EN, UVLO, OVP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +24V ADJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VOUT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VOUT ESD Rating Human Body Model (Tested per JESD22-A114E) . . . . . . . . . . . . . . .2.5kV Machine Model (Tested per JESD22-A115-A) . . . . . . . . . . . . . . . . . 250V Latch Up (Tested per JESD-78B; Class 2, Level A) . . . . . . . . . . . . . . 100mA Thermal Resistance (Typical) JA (C/W) JC (C/W) MSOP Package (Notes 4, 7) . . . . . . . . . . . . 140 41 DFN Package (Notes 5, 6) . . . . . . . . . . . . . . 46 5 Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . .+150C Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65C to +150C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Bias Supply Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3V to +20V OR'd Supply Voltage Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . +1V to BIAS Temperature Range (TA) . . . . . . . . . . . . . . . . . . . . . . . . . . -40C to +125C CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 5. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with "direct attach" features. See Tech Brief TB379. 6. For JC, the "case temp" location is the center of the exposed metal pad on the package underside. 7. For JC, the "case temp" location is taken at the package top center Electrical Specifications temperature range, -40C to +125C. SYMBOL VCC = BIAS = 12V, unless otherwise stated. TA = +25C to +85C. Boldface limits apply over the operating PARAMETERS TEST CONDITIONS MIN (Note 8) TYP MAX (Note 8) UNITS 1.9 2.5 2.95 V BIAS PORL2H POR Rising PORHYS POR Hysteresis BIAS Rising, GATE Rising 189 mV IBIAS_en_18 ISL6146A/B/D/E BIAS Current BIAS, VIN = 18V, ADJ, VOUT = 16.98V, enabled 3.6 5 mA IVIN_en_18 ISL6146A/B/D/E VIN Current BIAS, VIN = 18V, ADJ, VOUT = 16.98V, enabled 25 40 A IVIN_en_18 ISL6146C VIN Current VIN = 18V, ADJ, VOUT = 16.98V, enabled 3 4.5 mA IVOUT_en_18 ISL6146A/B/D/E VOUT Current BIAS, VIN = 18V, VOUT = 16.98V, enabled 14 20 A VOUT_en_18 ISL6146C VOUT Current VIN = 18V, VOUT = 16.98V, enabled 400 500 A ISL6146A/B/D/E BIAS Current BIAS, VIN = 18V, ADJ, VOUT = 16.98V, disabled 1.7 3 mA IVIN_den_18 ISL6146A/B/D/E VIN Current BIAS, VIN = 18V, ADJ, VOUT = 16.98V, disabled 27 37 A IVIN_den_18 ISL6146C VIN Current VIN = 18V, ADJ, VOUT = 16.98V, disabled 1.3 1.5 mA BIAS, VIN = 18V, VOUT = 16.98V, disabled 14 20 A IBIAS_den_18 IVOUT_den_18 ISL6146A/B/D/E VOUT Current IVOUT_den_18 ISL6146C VOUT Current tBIAS2GTE VIN = 18V, VOUT = 16.98V, disabled 385 500 A BIAS to GATE Delay BIAS > PORL2H to GATE Rising 150 210 s GATE VGH_3 Charge Pump Voltage VIN, BIAS = 3V VIN - VOUT > VFWD_VR VIN+5V VIN +7V VIN+10.5V V VGH_12 Charge Pump Voltage VIN, BIAS = 12V VIN - VOUT > VFWD_VR VIN+9V VIN +10V VIN+17.5V V VGH_18 Charge Pump Voltage VIN, BIAS = 18V VIN - VOUT > VFWD_VR VIN+9V VIN +10V VIN+18V V VGL Low Voltage Level VIN - VOUT < 0V 0 0.1 V IPDL Low Pull-Down Current VIN = 12V, VOUT = 12.2V ADJ = 11V 5 8.4 13 mA IPDH High Pull-Down Current VIN falling from 12V to 10V in 2s 3.5 6.5 5 A FN7667.2 July 12, 2012 ISL6146 Electrical Specifications VCC = BIAS = 12V, unless otherwise stated. TA = +25C to +85C. Boldface limits apply over the operating temperature range, -40C to +125C. (Continued) SYMBOL PARAMETERS TEST CONDITIONS MIN (Note 8) TYP MAX (Note 8) UNITS ttoff Fast Turn-off Time VIN = VBIAS = 12V, VGATE = 18V to 10V, CGATE = 57nF 65 130 ns ttoffs Slow Turn-off Time VIN = VBIAS = 12V, VGATE = 18V to 10V, CGATE = 57nF 58 80 s ION Turn-On Current BIAS = 12V, VG = 0V 1 mA BIAS = 12V, VG = 20V 0.15 mA VVG_FLTr GATE to VIN Rising Fault Voltage GATE > VIN, enabled, FLT output is high. (Does not apply to ISL6146D and ISL6146E) 320 440 560 mV VVG_FLTf GATE to VIN Falling Fault Voltage GATE > VIN, enabled, FLT output is low. (Does not apply to ISL6146D and ISL6146E) 140 220 300 mV CONTROL AND REGULATION I/O VRr Reverse Voltage Detection Rising VOUT Threshold VOUT rising 35 57 79 mV VRf Reverse Voltage Detection Falling VOUT Threshold VOUT falling 10 30 51 mV tRs Reverse Voltage Detection Response Time VFWD_VR Amplifier Forward Voltage Regulation VOS_HS VTH(HS5k) VTH(HS100k) tHSpd 10 ISL6146 controls voltage across FET VDS to VFWD_VR during static forward operation at loads resulting in Id*rDS(ON) < VFWD_VR HS Comparator Input Offset Voltage ADJ Adjust Threshold with 5k to GND RADJ = 5k to GND ADJ Adjust Threshold with 100k to GND RADJ = 100k to GND HS Comparator Response Time VOUT > VIN, 1ns transition, 5V differential VFWD_FLT VIN to VOUT Forward Fault Voltage VIN > VOUT, GATE is fully on, FLT output is low VFWD_FLT_HYS VIN to VOUT Forward Fault Voltage Hysteresis VIN > VOUT, GATE is fully on, FLT output is high s 11 19 28 mV -14 0.7 14 mV 0.57 0.8 1.1 V 10 40 95 mV 170 330 450 ns 570 44 mV mV FAULT OUTPUT IFLT_SINK FAULT Sink Current BIAS = 18V FAULT = 0.5V, VIN < VOUT, VGATE = VGL IFLT_LEAK FAULT Leakage Current FAULT = "VFLT_H", VIN > VOUT, VGATE = VIN + VGQP tFLT_L2H FAULT Low to High Delay tFLT_H2L FAULT High to Low Delay 5 9 mA 0.04 10 A GATE = VGQP to FAULT output is high 10 23 s GATE = VIN to FAULT output is low 1.7 3 s 580 606 631 mV 580 606 ENABLE UVLO/OVP/ADJ INPUTS VthRa VthR_hysa VthFb VthF_hysb VthFc VthF_hysc VthRc VthR_hysc ISL6146A/D EN Rising Vth ISL6146A/D EN Vth Hysteresis ISL6146B/E EN Falling Vth -90 ISL6146B/E EN Vth Hysteresis ISL6146C OVP Falling Vth +90 580 ISL6146C OVP Vth Hysteresis ISL6146C UVLO Rising Vth ISL6146C UVLO Vth Hysteresis 6 mV 631 606 mV 631 +90 580 606 -90 mV mV mV 631 mV mV FN7667.2 July 12, 2012 ISL6146 Electrical Specifications VCC = BIAS = 12V, unless otherwise stated. TA = +25C to +85C. Boldface limits apply over the operating temperature range, -40C to +125C. (Continued) SYMBOL tEN2GTER tEN2GTEF PARAMETERS TEST CONDITIONS MIN (Note 8) TYP MAX (Note 8) UNITS EN/UVLO Rising to GATE Rising Delay 10 12 s EN/OVP Falling to GATE Rising Delay 9 12 s EN/UVLO Falling to GATE Falling Delay 2 4 s EN/OVP Rising to GATE Falling Delay 2 4 s Ren_h ENABLE Pull-Down Resistor ISL6146A 2 M Ren_l ENABLE Pull-Up Resistor ISL6146B 2 M Vadj ADJ Pin Voltage RADJ 5k to 100k 0.4 V Radj ADJ Pull-Up Resistor Internal ADJ Pull-up Resistor to VOUT 3.85 M OTS Over-Temperature Sense Fault signals in operation 140 C 20 C 125 C OTSHYS HTS Over-Temperature Sense Hysteresis High Temperature Sense Fault signals upon enabling NOTE: 8. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. 7 FN7667.2 July 12, 2012 ISL6146 Typical Performance Curves 4.0 3.0 2.0 18V DISABLED 12V DISABLED 3V DISABLED 35 12V ENABLED 30 3V ENABLED 25 20 18V DISABLED 12V DISABLED 3V DISABLED VOUT CURRENT 15 1.5 1.0 18V ENABLED VIN CURRENT VIN/VOUT CURRENT (mA) IBIAS/IVIN CURRENT (mA) 3.5 2.5 40 18V ENABLED 12V ENABLED 3V ENABLED -40 25 85 TEMPERATURE (C) 10 125 FIGURE 3. ISL6146A/B/D/E BIAS AND ISL6146C VIN CURRENT vs TEMPERATURE -40 25 85 TEMPERATURE (C) 125 FIGURE 4. ISL6146A/B/C/D/E VIN AND VOUT CURRENT vs TEMPERATURE 35 2.60 BIAS = 18V 2.55 2.50 BIAS = 12V 25 POR Vth RISING 2.45 VPOR Vth (V) HARD ON GATE VOLTAGE (V) 30 20 15 BIAS = 3V 10 2.40 2.35 2.30 2.25 POR Vth FALLING 2.20 2.15 5 2.10 0 -40 25 85 2.05 125 -40 TEMPERATURE (C) 25 85 125 TEMPERATURE (C) FIGURE 5. GATE VOLTAGE vs TEMPERATURE FIGURE 6. POR Vth RISING AND FALLING VOLTAGE 0.74 0.70 0.72 0.65 EN DEASSERT RISING Vth 0.70 EN ASSERT RISING Vth 0.68 0.55 EN Vth (V) EN Vth (V) 0.60 EN DEASSERT FALLING Vth 0.50 0.66 0.64 0.62 0.60 EN ASSERT FALLING Vth 0.58 0.45 0.56 0.40 0.54 -40 25 85 TEMPERATURE (C) FIGURE 7. ISL6146A/D EN Vth vs TEMPERATURE 8 125 -40 25 85 125 TEMPERATURE (C) FIGURE 8. ISL6146B/E EN Vth vs TEMPERATURE FN7667.2 July 12, 2012 ISL6146 Typical Performance Curves (Continued) 750 1.3 VG = 0V OVP RISING GATE TURN-ON CURRENT (mA) OVP AND UVLO Vth (mV) 700 650 600 UVLO RISING AND OVP FALLING 550 500 1.1 0.9 0.7 0.5 0.3 UVLO FALLING 450 -40 25 85 TEMPERATURE (C) 0.1 125 7.0 10 6.5 9 6.0 5.5 5.0 4.5 4.0 3.5 3.0 8 7 6 5 4 3 2 -40 25 85 TEMPERATURE (C) 0 125 FIGURE 11. GATE HARD TURN-OFF CURRENT -40 25 85 TEMPERATURE (C) 125 FIGURE 12. GATE SLOW TURN-OFF CURRENT 56.0 45 55.5 40 55.0 RESPONSE TIME (s) REVERSE DETECTION VOLTAGE (mV) 125 1 2.5 2.0 25 85 TEMPERATURE (C) FIGURE 10. GATE TURN-ON CURRENT VIN = 12V GATE PULL-DOWN CURRENT (mA) GATE PULL-DOWN CURRENT (A) FIGURE 9. ISL6146C UVLO/OVP Vth vs TEMPERATURE -40 54.5 54.0 53.5 35 30 25 53.0 20 52.5 52.0 -40 25 85 TEMPERATURE (C) 125 FIGURE 13. INCREASING REVERSE VOLTAGE DETECTION Vth 9 15 -40 25 85 TEMPERATURE (C) 125 FIGURE 14. REVERSE VOLTAGE RESPONSE TIME FN7667.2 July 12, 2012 ISL6146 Typical Performance Curves (Continued) 3 300 280 260 RESPONSE TIME (ns) OFFSET VOLTAGE (mV) 2 1 0 -1 240 220 200 180 160 140 -2 120 -3 -40 25 85 TEMPERATURE (C) 100 125 FIGURE 15. HIGH SPEED COMPARATOR OFFSET VOLTAGE 700 1.000 600 0.999 RELATIVE % HS COMP ADJUST VTH (mV) 1.001 RADJ TO GND = 5k 500 400 300 200 0.998 0.997 0.996 0.995 RADJ TO GND = 100k 100 -40 25 85 TEMPERATURE (C) 0.994 125 FIGURE 17. HS COMPARATOR ADJUSTABLE Vth 0.993 3 12 BIAS VOLTAGE (V) 18 FIGURE 18. EN/EN/OVP/UVLO Vth DELTA vs BIAS VOLTAGE NORMALIZED TO BIAS = 12V 21.0 465 20.8 460 20.6 VIN - VOUT FAULT VTH (mV) VIN TO VOUT FWD VOLTAGE REG (mV) 125 1.002 800 20.4 20.2 20.0 19.8 19.6 19.4 455 450 445 440 435 430 425 19.2 19.0 25 85 TEMPERATURE (C) FIGURE 16. VHIGH SPEED COMPARATOR RESPONSE TIME 900 0 -40 -40 25 85 TEMPERATURE (C) FIGURE 19. FORWARD VOLTAGE REGULATION 10 125 420 -40 25 85 TEMPERATURE (C) 125 FIGURE 20. VIN TO VOUT FORWARD FAULT VOLTAGE FN7667.2 July 12, 2012 ISL6146 Typical Performance Curves (Continued) GATE 2 GATE1 GATE 2 GATE1 IIN2 IIN1 IIN1 IIN2 FIGURE 21. ISL6146C SLOW RAMP CONNECT 12V ORing GATE1 GATE 2 FIGURE 22. ISL6146C SLOW RAMP DISCONNECT 12V ORing GATE 2 GATE1 IIN2 IIN1 IIN2 IIN1 FIGURE 23. ISL6146C HOT SWAP CONNECT 12V ORing FIGURE 24. ISL6146C HOT DISCONNECT 12V ORing GATE GATE EN/UVLO EN/UVLO FIGURE 25. ISL6146A/D EN/ISL6146C UVLO TO GATE ON DELAY 11 FIGURE 26. ISL6146A/D EN/ISL6146C UVLO TO GATE OFF DELAY FN7667.2 July 12, 2012 ISL6146 Typical Performance Curves (Continued) GATE GATE EN EN FIGURE 27. ISL6146B/E EN TO GATE ON DELAY FIGURE 28. ISL6146B/E EN TO GATE OFF DELAY GATE OVP OVP GATE FIGURE 29. ISL6146C OVP TO GATE ON DELAY VIN RISING THROUGH BOTH THE PROGRAMMED UVLO AND OVP LEVELS. GATE TURNS-ON AS VIN EXCEEDS 10V THEN TURNS-OFF AS VIN EXCEEDS 15V FIGURE 30. ISL6146C OVP TO GATE OFF DELAY VIN FALLING THROUGH BOTH THE PROGRAMMED OVP AND UVLO LEVELS. GATE TURNS-ON AS VIN > 13V THEN TURNS-OFF AS VIN > 8.3V VIN GATE FIGURE 31. ISL6146C RISING VIN, UVLO AND OVP FUNCTION 12 GATE VIN FIGURE 32. ISL6146C FALLING, VIN OVP AND UVLO FUNCTION FN7667.2 July 12, 2012 ISL6146 Typical Performance Curves (Continued) VIN RISING TO <2.5V WHEN GATE BECOMES ACTIVE GGATE AT E VIN V IN VOUT VO UT GATE VIN FIGURE 33. BACK-TO-BACK FET TURN_ON DETAIL GATE FAST OFF, ~200ns FALL TIME ~70ns FROM 20V TO 12.6V ACROSS 57nF GATE OUTPUT SINKING ~ 6A FIGURE 34. ISL6146 RISING POR Vth VOUT HIGH SPEED COMPARATOR Vth = VOS(HS) GATE1 VIN1 SHORTED TO GND GATE2 FIGURE 35. FAST GATE TURN-OFF WITH 57nF GATE VOUT HIGH SPEED COMPARATOR Vth = 800mV GATE1 FIGURE 36. RESPONSE TO VIN SHORTED TO GND WITH ADJ SHORTED TO VOUT VOUT HIGH SPEED COMPARATOR Vth = 40mV GATE1 VIN1 SHORTED TO GND VIN1 SHORTED TO GND GATE2 GATE2 FIGURE 37. RESPONSE TO VIN SHORTED TO GND WITH ADJ 5k TO GND 13 FIGURE 38. RESPONSE TO VIN SHORTED TO GND WITH ADJ 100k TO GND FN7667.2 July 12, 2012 ISL6146 Typical Performance Curves (Continued) VIN VIN VOUT FLT GATE VIN - VOUT FIGURE 40. FAULT ASSERTING VIN TO VOUT > VFWD_FLT 35 40 30 35 25 % OF DISTRIBUTION % OF DISTRIBUTION FIGURE 39. VIN HOT SWAPPED TO GATE WITH BIAS = 12V NO LOAD 20 15 10 25 20 15 10 5 0 30 5 -1 0 1 2 3 4 5 HS COMP ADJUST VTH (mV) 6 7 FIGURE 41. HIGH SPEED COMPARATOR OFFSET VOLTAGE DISTRIBUTION 0 17 18 19 20 VFWD_VR (mV) 21 22 FIGURE 42. FOWARD REGULATION VOTLAGE DISTRIBUTION 40 35 + VDS % OF DISTRIBUTION 30 0V VR 25 tHSpd 20 15 20V VGATE 10 5 0 12.6V 50 52 54 56 58 60 62 64 66 68 VRr (mV) FIGURE 43. REVERSE DETECTION RISING VOLTAGE DISTRIBUTION 14 VBIAS = VIN = 12V tOFF FIGURE 44. FAST RAMP REVERSE PROTECTION TIMING DIAGRAM FN7667.2 July 12, 2012 ISL6146 Typical Performance Curves (Continued) FLT FLT GATE GATE VIN VIN FIGURE 45. ISL6146A FLT RESPONSE TO NON-CONDUCTION 15 FIGURE 46. ISL6146D FLT RESPONSE TO NON-CONDUCTION FN7667.2 July 12, 2012 ISL6146 Functional Description Functional Overview In a redundant power distribution system, similar potential and parallel power supplies each contribute to the load current through various active and passive current sharing schemes. Typically ORing power diodes are used to protect against reverse current flow in the event that one of the power supplies falls below the common bus voltage or develops a catastrophic failure. However, using a discrete ORing diode solution has some significant drawbacks. The primary downside is the increased power dissipation loss in the ORing diodes as system power requirements increase. At the lowest voltages where the ISL6146 is designed for use, the voltage distribution losses across an ORing diode can be a significant percentage, in some cases approaching 70%. Another disadvantage when using an ORing diode is failure to detect a shorted or opened current path, which jeopardizes system power availability and reliability. An open diode may reduce the system to a single point of failure while a shorted diode eliminates the system's power protection. Using an active ORing FET controller, such as the ISL6146, helps with these potential issues. The use of a low on-resistance FET as the ORing component allows for a more efficient system design as the voltage across the FET is much lower than that across a forward biased diode. Additionally, the ISL6146 has a dedicated fault (FAULT) output pin that indicates when there is a conditional or FET fault short providing the diagnostic capability that a diode is unable to. The ISL6146 is designed to OR together voltages as low as 1V when supplied with a separate bias supply of 3V or greater. Otherwise, the ISL6146 is designed to be biased from and OR voltages across the 3V to 20V nominal supply range. In a single FET configuration as voltage is first applied to a VIN pin, the FET body diode conducts providing all the ISL6146s connected on a common bus circuit, bias via the VOUT pins. As individual power supply voltages ramp up in excess of the rising POR threshold, the ISL6146's internal charge pump activates to provide a floating gate drive voltage for the external N-channel ORing MOSFET, thus turning the FETs on once VIN > VOUT. The ISL6146 continuously monitors the drain and source of the ORing FET and provides a reverse voltage (N-channel MOSFET VOUT - VIN) detection threshold (VR) that, when exceeded, indicates a reverse current condition. Once this threshold is exceeded, the ISL6146 turns off the ORing FET by pulling down the GATE pin to GND. The ISL6146 also provides high speed VOUT > VIN transient protection as in the case of a catastrophic VIN failure. The ISL6146 additionally provides for adjustment of the VIN - VOUT reverse voltage Vth(VR Vth) via the ADJ pin of the ISL6146 with an external resistor to GND. This allows adjusting the VIN - VOUT voltage threshold level to compensate for normal system voltage fluctuations, thus eliminating unnecessary reaction by the ISL6146. The total VIN - VOUT VR Vth is the sum of both the internal offset and the external programmed VR Vth. In the event of a VOUT > VIN condition, the ISL6146 responds either with a high or low current pull-down on the GATE pin depending on whether the High Speed comparator (HSCOMP) has been activated or not. The HSCOMP determines if the VR occurred within 1s, by continuously monitoring the FET VDS and if so, the high pull-down current is used to turn off the ORing FET. In the event of a falling VIN transition in <1s, (i.e., a catastrophic failure of the power source) the HSCOMP protects the common bus from the individual faulted power supply short by turning off the shorted supply's ORing MOSFET in less than 300ns, ensuring the integrity of the common bus voltage from reverse current to the damaged supply. Once the correct VIN > VOUT relationship is established again, the ISL6146 again turns on the FET. The FAULT pin is an open drain, active low output indicating that a fault or specific condition has occurred, these include: * GATE is OFF (GATE < VIN+0.2V). Lack of conduction, not a fault, just not on. ISL6146D and ISL6146E do not respond to this condition * Faults resulting in VIN - VOUT > 0.57V when ON * An open FET resulting in body diode conduction * Excessive current through FET * FET Faults monitored and reported include - G-D, gate unable to drive to Q-pump voltage - G-S, gate unable to drive to Q-pump voltage - D-S shorts, when GATE is OFF VDS < 2V - VIN < POR - Missing VIN - VIN shorted to GND On the ISL6146C version, a conditional fault is also signalled if the VIN is not within the programmed UVLO and OVP levels. The ISL6146 has an on-chip over-temperature fault threshold of ~+140C with a 20C hysteresis. Although the ISL6146 itself produces little heat, it senses the environment in which it is, likely including a close by FET. The ISL6146A/D and ISL6146B/E are functional variants with an enabling input of either polarity. This feature is used when the need to interrupt the current path via signaling is necessary. This is accomplished by implementing two FETs in series so that there is a body diode positioned to block current in either direction. This functionality is considered an additional enhancement to the ORing diode it replaces. The ISL6146C employs the use of a programmable Undervoltage Lock Out (UVLO) and a programmable Overvoltage Protection (OVP) input. This allows the GATE to only turn-on when the monitored voltage is between the programmed lower and upper levels. This application would use the back-to-back FET configuration. In the event that the current path does not need to be interrupted then the EN, UVLO and OVP inputs can all be overridden. The ISL6146D and ISL6146E are variants of the ISL6146A and ISL6146B respectively, the difference being the former do not respond to a nonconduction condition (when enabled and VIN > VOUT, the GATE is not on) unlike the latter that do signal a fault. 16 FN7667.2 July 12, 2012 ISL6146 Applications Information Power-Up Considerations BIAS AND VIN CONSTRAINTS Upon power-up when the VIN supply is separate from the BIAS supply, the BIAS voltage must be greater or equal to the VIN voltage at all times. When using a single supply for both the ISL6146 bias and the ORing supply, the VIN and BIAS pins can be configured with a low value resistor between the two pins to provide some isolation and decoupling to support the chip bias even as the OR'd supply experiences voltage droops and surges. Although not necessary to do so, it is a best design practice for particularly noisy environments. FET TO IC LAYOUT RECOMMENDATIONS Connections from the FET(s) to the ISL6146 VIN and VOUT pins must be Kelvin in nature and as close to the FET drain and source PCB pads as possible to eliminate any trace resistance errors that can occur with high currents. This connection placement is most critical to providing the most accurate voltage sensing particularly when the back-to-back FET configuration is used. Likewise, connections from OVP, UVLO and ADJ are also critical to optimize accuracy. ADJUSTING THE HS COMPARATOR REVERSE VOLTAGE THRESHOLD The ISL6146 allows adjustment of the HS Comparator reverse voltage detection threshold (VR Vth), the difference in VOUT - VIN. There are two valid ADJ pin configurations: 1. ADJ connected to VOUT: This makes the HS comparator threshold equal to the intrinsic error in the HS comparator input. This is the default condition and the most likely used configuration. 2. A single resistor is connected from ADJ pin to ground: Making the HS comparator threshold = VOUT - 4k/RADJ. So, for a 100k REXT, HS Comparator threshold = 40mV below VOUT and for a 5k REXT HS comparator threshold = ~ 800mV below VOUT. The recommended resistor range is 5k to 100k for this voltage adjustment. At power-up, the HS comparator threshold is default set to the internal device error first, and then released to the user programmed threshold after the related circuits are ready. It takes ~20s for the circuit to switch from the default setting to the user programmed threshold after a POR startup. The current out of the ADJ pin with a resistor to GND is equal to 0.4V/REXT. BACK-TO-BACK FET CONFIGURATION When using the back-to-back FET configuration, the FET choice must be such that the voltage across both FETs at full current loading be less than the minimum forward voltage fault threshold of 400mV to avoid unintended fault notification. In this configuration, it may be tempting to use the enable inputs to force a path by switching between the two as opposed to having both paths on, and having the higher voltage source provide current. The problem with that is the timing of the FETs on and off, so that excessive VOUT voltage droop is not introduced if the turn-off happens faster, or before the (or a slower) turn-on momentarily leaves the load with an inadequate power connection. Typical Applications Circuits There are four basic configurations that the ISL6146 can be used in: 1. For voltages >3V where the BIAS and VIN are common 2. For a very low ORing voltage, <3V operation, BIAS >3V 3. For a voltage window compliant operation and, 4. For a signaled operation where the current path is controlled by an input signal or minimum voltage condition. Each of these configurations can be tailored for the High Speed Comparator (HS COMP) reverse threshold via the ADJ input being connected either to VOUT or to GND via a resistor as previously explained. Additionally, the voltage window is adjustable for both a minimum and maximum operating voltage via the UVLO and OVP inputs and a resistor divider also explained earlier. Also, soft-start and turn-on and turn-off characteristics can be tailored to suit. The three evaluation platforms provided demonstrate the four basic configurations and provide for the additional tailoring of the various performance characteristics. BIAS VOLTAGE >3V + Q1 C O M M O N + VERY LOW VOLTAGE DC - DC (1V-3V) VIN BIAS EN GATE VOUT P O W E R ADJ ISL6146A FLT B U S GND - + Q2 C O M M O N + VIN VERY LOW VOLTAGE DC - DC (1V-3V) GATE BIAS VOUT P O W E R ADJ ISL6146A FLT B U S EN GND FIGURE 47. LOW VOLTAGE APPLICATION DIAGRAM 17 FN7667.2 July 12, 2012 ISL6146 The Figure 1 circuit shown on page 1 is the basic circuit used for ORing voltages >3V to 20V. The ISL6146A application shown in Figure 47 is the configuration for ORing very low voltages of 1V to 3V. Additionally, this application shows the utilization of the ADJ input with a single resistor tied to GND. This provides the user a programmable level of VOUT > VIN before the High Speed (HS) Comparator is activated and the GATE output is pulled down to allow for normal voltage fluctuations in the system. Notice that in both of these circuits, the EN or EN inputs are defaulted to enabled and have no current path on/off control. Failure to do so correctly will result in only body diode conduction and a resulting fault indication. The VIN and VOUT to FET and GND to ADJ connections are drawn to emphasize the Kelvin connection necessary to correctly monitor the voltage across the FET, and for the VR Vth monitor to eliminate any stray resistance effects. Q1 Q2 VIN VOUT GATE UVLO VOLTAGE DC - DC 3V-20V ADJ ISL6146C FLT OVP C O M M O N P O W E R B U S GND - + Q3 Q4 C O M M O N + VIN VOLTAGE DC - DC 3V-20V GATE UVLO VOUT ADJ ISL6146C FLT OVP GND P O W E R B U S - FIGURE 48. TYPICAL ISL6146C APPLICATION DIAGRAM The ISL6146C application shown in Figure 48 is limited to the 3V to 20V VIN range and must implement the back-to-back FET configuration to utilize the UVLO and OVP inputs and capabilities. As the VIN voltage rises above the minimum programmed voltage, the related ORing FETs will turn on and stay on until either the minimum voltage requirement is no longer met or the VIN voltage exceeds its programmed maximum. The minimum and maximum programmed voltage levels are done with the resistor divider on the UVLO and OVP pins. These levels should be programmed to take into account conduction path losses to the load in addition to the IC operational constraints. When using the back-to-back FET configuration, the user must chose FETs to ensure (2rDS(ON) + PCB IR) ILOAD < 0.5V to avoid tripping the VIN - VOUT > 0.5V when ON fault. 18 Q1 Q2 + C O M M O N + VERY LOW VOLTAGE DC - DC (1V-BIAS) VIN VOUT GATE BIAS P O W E R ADJ ISL6146A/B FLT GND EN/EN - ENABLED WHEN SIGNALED B U S + Q3 Q4 C O M M O N + GATE VIN + + DISTRIBUTED VOLTAGE >3V VERY LOW VOLTAGE DC - DC (1V-BIAS) VOUT BIAS P O W E R ADJ ISL6146A/B GND - FLT EN/EN ENABLED WHEN SIGNALED B U S FIGURE 49. CONTROLLED ON/OFF APPLICATION DIAGRAM The application diagram in Figure 49 shows the ISL6146A or ISL6146B utilizing the EN or EN pin as a signalled input to open or close the conduction path from power supply to load. This feature can be implemented on ORing 1V to 20V but is shown for ORing <3V. The enable input signaling can be simultaneous across the N+1 number of ISL6146s used. Although not needed for thermal relief, connect the DFN EPAD to GND. SWITCH-OVER CIRCUITS Switch over applications are different than ORing applications in that, the former are looking for the presence of or a condition of a preferred supply in order to switch to it. Whereas true ORing consists of a redundant N+1 configuration with no preferred source. The following 2 circuits are simple single ISL6146 switchover circuits optimized for situations particular to the VBATT and VEXT voltages relative to each other. Figure 50 shows an ISL6146B switchover circuit where VEXT, when present, is the preferred source and VBATT could be lesser or greater than VEXT. This circuit senses the presence of the preferred voltage supply to a programmable threshold level that when exceeded, VEXT is passed to the output as VBATT is disconnected from the output. R1 & R2 program the VEXT level that must be preset for the preferred voltage to be passed to the output. Q3 is necessary if VBATT can ever exceed VEXT to prevent current from flowing into VEXT when present. The body diode of Q3 prevents that when Q1 is on regardless of the VBATT voltage. FN7667.2 July 12, 2012 ISL6146 The ISL6146 bias is pulled from the common drain node to ensure an always adequate bias from either source when the other is absent Q1 VEXT 3.3V - 24V SWITCHED OUTPUT Q2 Use when VBATT > VEXT Q3 disconnects VBATT from output when GATE is off. Q3 VBATT 3.3V-20V VIN GATE Q1 ISL6146B EN Figure 52 is a ISL6146A switchover circuit to use where the preferred VEXT source is always greater than the VBATT. Because this is so, there is no need for a 3rd FET for blocking as in Figure 50. Additionally, the preferred VEXT source when present or at a programmed minimum threshold voltage via R1 and R2 divider will turn on Q2/turn-off Q1 but when absent or not minimally adequate, will do the opposite. In this circuit, with the ISL6146A not connected to the battery, and thus no constant IVIN load on it, which allows for longer battery life. Bias voltage is pulled from the common output to ensure an always adequate IC bias from either source. VOUT FLT BIAS R1 All of the scope shots were taken with a 5A load and 100F of bulk load capacitance. GND ADJ VBATT SWITCHED OUTPUT R3 R2 Use when VBATT < VEXT Q2 FIGURE 50. ISL6146B EXTERNAL SWITCHOVER SCHEMATIC VEXT Figure 51 shows operational scope shots of the above circuit. VIN GATE FLT BIAS BATT SUPPLY EXT SUPPLY R1 ISL6146A EN VOUT ADJ GND R2 VOUT FIGURE 53. ISL6146A EXTERNAL SWITCHOVER SCHEMATIC GATE BATT SUPPLY EXT SUPPLY VOUT FIGURE 51. EXTERNAL SUPPLY < BATT SUPPLY CONNECTED BATT SUPPLY EXT SUPPLY GATE VOUT FIGURE 54. EXTERNAL SUPPLY > BATT SUPPLY CONNECTED GATE FIGURE 52. EXTERNAL SUPPLY < BATT SUPPLY DISCONNECTED 19 FN7667.2 July 12, 2012 ISL6146 The ISL6146AEVAL1Z, ISL6146DEVAL1Z are configured to have a 8.5V minimum turn-on threshold with a 1.2V hysteresis. BATT SUPPLY EXT SUPPLY The ISL6146BEVAL1Z, ISL6146EEVAL1Z are configured as a minimally featured maximum performance ORing FET controller for 3V to 20V. VOUT The ISL6146CEVAL1Z is configured to operate with a 10.8V lower turn on threshold and 14.9V upper turn-off threshold. All five boards are equipped with 50A capable FETs for high current evaluations and with a minimum of VIN and VOUT bulk capacitance likely to be found in any power system design. GATE After determining the BIAS source along with VIN voltage criteria and configuring the evaluation board if necessary, for the application to be evaluated the board is ready for power. Apply the BIAS voltage first (via the test points labeled BIAS), if separate from VIN, then the VIN voltage. Monitor the provided test points for device performance with current loads up to 50A. FIGURE 55. EXTERNAL SUPPLY > BATT SUPPLY DISCONNECTED ISL6146 Evaluation Platforms Description and Use of the Evaluation Boards The three ISL6146 evaluation boards are used to demonstrate the four application configurations discussed earlier. All the boards have ADJ shorted to VOUT with the PCB layout having the component footprints to insert a resistor of choice between ADJ and GND to adjust the HS COMP Vth. Likewise, the VIN is connected to BIAS but these can be separated to provide an adequate BIAS voltage when ORing <3V supplies or if providing a separate from VIN voltage to BIAS. FIGURE 56. ISL6146AEVAL1Z, ISL6146DEVAL1Z PHOTOGRAPH 20 Figures 56 through 61 illustrate the three ISL6146 evaluation boards for the three typical applications in photograph and schematic form. FIGURE 57. ISL6146AEVAL1Z, ISL6146DEVAL1Z SCHEMATIC FN7667.2 July 12, 2012 ISL6146 FIGURE 58. ISL6146BEVAL1Z, ISL6146EEVAL1Z PHOTOGRAPH FIGURE 59. ISL6146BEVAL1Z, ISL6146EEVAL1Z SCHEMATIC FIGURE 60. ISL6146CEVAL1Z PHOTOGRAPH FIGURE 61. ISL6146CEVAL1Z SCHEMATIC (UVLO AND OVP TEST POINT LABELS ARE SWAPPED) 21 FN7667.2 July 12, 2012 ISL6146 TABLE 2. ISL6146xEVALZ BOM REFERENCE DESIGNATOR VALUE DESCRIPTION MANUFACTURER PART NUMBER ISL6146AEVAL1Z U1, U2 Q1, Q2, Q11, Q12 ISL6146A ORing FET Controller Intersil 30V, 50A FET Various R1, 11 66.5k RES, SMD, 0603, 1% Generic R2, R12, R6, R16 4.99k RES, SMD, 0603, 1% Generic R3, R13 10 RES, SMD, 0603, 1% Generic R4, R14 0 RES, SMD, 0603, 1% Generic R5, R15 DNP RES, SMD, 0603, 1% Generic R7, R17 10k RES, SMD, 0603, 1% Generic C1, C11, C5 C15 100F Alum. Elect SMD Cap Generic C2, C3, C12 C13 1F CAP, SMD, 0603, 50V, 10% Generic C4, C14 DNP CAP, SMD, 0603, 50V, 10% Generic Test Point Generic Banana Jack Generic ISL6146B ORing FET Controller Intersil TPx Jx ISL6146AFUZ ISL6146BEVAL1Z U1, U2 Q1, Q11 30V, 50A FET Various R4, R14 4.99k RES, SMD, 0603, 1% Generic R1, R10 10 RES, SMD, 0603, 1% Generic R2, R12 0 RES, SMD, 0603, 1% Generic R3, R13 DNP RES, SMD, 0603, 1% Generic R5, R15 10k RES, SMD, 0603, 1% Generic C1, C11, C5 C15 100F ALum. Elect SMD Cap Generic C2, C3, C12 C13 1F CAP, SMD, 0603, 50V, 10% Generic C4, C14 DNP CAP, SMD, 0603, 50V, 10% Generic Test Point Generic Banana Jack Generic ISL6146C ORing FET Controller Intersil 30V, 50A FET Various TPx Jx ISL6146BFUZ ISL6146CEVAL1Z U1, U2 Q1, Q2, Q11, Q12 R1, 11 93.1k RES, SMD, 0603, 1% Generic R2, R12 1.4k RES, SMD, 0603, 1% Generic R3, R13 4.53k RES, SMD, 0603, 1% Generic R4, R14 0 RES, SMD, 0603, 1% Generic R5, R15 DNP RES, SMD, 0603, 1% Generic R6, R16 4.99k RES, SMD, 0603, 1% Generic R7, R17 10k RES, SMD, 0603, 1% Generic C1, C11, C3 C13 100F ALum. Elect SMD Cap Generic C2, C12 1F TPx Jx CAP, SMD, 0603, 50V, 10% Generic Test Point Generic Banana Jack Generic ISL6146D ORing FET Controller Intersil 30V, 50A FET Various ISL6146CFUZ ISL6146DEVAL1Z U1, U2 Q1, Q2, Q11, Q12 22 ISL6146DFUZ FN7667.2 July 12, 2012 ISL6146 TABLE 2. ISL6146xEVALZ BOM (Continued) REFERENCE DESIGNATOR VALUE R1, 11 66.5k RES, SMD, 0603, 1% DESCRIPTION Generic MANUFACTURER R2, R12, R6, R16 4.99k RES, SMD, 0603, 1% Generic R3, R13 10 RES, SMD, 0603, 1% Generic R4, R14 0 RES, SMD, 0603, 1% Generic R5, R15 DNP RES, SMD, 0603, 1% Generic R7, R17 10k RES, SMD, 0603, 1% Generic C1, C11, C5 C15 100F Alum. Elect SMD Cap Generic C2, C3, C12 C13 1F CAP, SMD, 0603, 50V, 10% Generic C4, C14 DNP CAP, SMD, 0603, 50V, 10% Generic Test Point Generic Banana Jack Generic TPx Jx PART NUMBER ISL6146EEVAL1Z U1, U2 Q1, Q11 ISL6146E ORing FET Controller Intersil 30V, 50A FET Various R4, R14 4.99k RES, SMD, 0603, 1% Generic R1, R10 10 RES, SMD, 0603, 1% Generic R2, R12 0 RES, SMD, 0603, 1% Generic R3, R13 DNP RES, SMD, 0603, 1% Generic R5, R15 10k RES, SMD, 0603, 1% Generic C1, C11, C5 C15 100F ALum. Elect SMD Cap Generic C2, C3, C12 C13 1F CAP, SMD, 0603, 50V, 10% Generic C4, C14 DNP CAP, SMD, 0603, 50V, 10% Generic Test Point Generic Banana Jack Generic TPx Jx 23 ISL6146EFUZ FN7667.2 July 12, 2012 ISL6146 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest revision. DATE REVISION CHANGE June 18, 2012 FN7667.2 Added ISL6146D and ISL6146E. References to these products added throughout the datasheet. Added Figures 45 & 46 to illustrate the fault differences between ISL6146A/B and ISL6146D/E. Moved Figure 50 and revised the related text on page 19 before the evaluation board section. Added Figures 51 - 55 and related text on page 19 to page 20. February 27, 2012 FN7667.1 Removed note "MSOP packaged parts to be released soon" from "Ordering Information" on page 3. Added FIgures 42 & 43 on page 14. December 16, 2011 FN7667.0 Initial Release Products Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks. Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a complete list of Intersil product families. For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page on intersil.com: ISL6146 To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff FITs are available from our website at: http://rel.intersil.com/reports/sear For additional products, see www.intersil.com/product_tree Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted in the quality certifications found at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 24 FN7667.2 July 12, 2012 ISL6146 Package Outline Drawing L8.3x3J 8 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE Rev 0 9/09 2X 1.950 3.00 B 0.15 8 5 3.00 (4X) 6X 0.65 A 1.64 +0.10/ - 0.15 6 PIN 1 INDEX AREA 6 PIN #1 INDEX AREA 1 4 4 8X 0.30 8X 0.400 0.10 TOP VIEW 0.10 M C A B 2.38 +0.10/ - 0.15 BOTTOM VIEW SEE DETAIL "X" ( 2.38 ) ( 1.95) 0.10 C Max 1.00 C 0.08 C SIDE VIEW ( 8X 0.60) (1.64) ( 2.80 ) PIN 1 C 0 . 2 REF 5 (6x 0.65) 0 . 00 MIN. 0 . 05 MAX. ( 8 X 0.30) DETAIL "X" TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal 0.05 4. Dimension applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. 25 The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. FN7667.2 July 12, 2012 ISL6146 Package Outline Drawing M8.118 8 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE Rev 4, 7/11 5 3.00.05 A DETAIL "X" D 8 1.10 MAX SIDE VIEW 2 0.09 - 0.20 4.90.15 3.00.05 5 0.95 REF PIN# 1 ID 1 2 B 0.65 BSC GAUGE PLANE TOP VIEW 0.55 0.15 0.25 33 0.85010 H DETAIL "X" C SEATING PLANE 0.25 - 0.36 0.08 M C A-B D 0.10 0.05 0.10 C SIDE VIEW 1 (5.80) NOTES: (4.40) (3.00) 1. Dimensions are in millimeters. (0.65) (0.40) (1.40) TYPICAL RECOMMENDED LAND PATTERN 26 2. Dimensioning and tolerancing conform to JEDEC MO-187-AA and AMSEY14.5m-1994. 3. Plastic or metal protrusions of 0.15mm max per side are not included. 4. Plastic interlead protrusions of 0.15mm max per side are not included. 5. Dimensions are measured at Datum Plane "H". 6. Dimensions in ( ) are for reference only. FN7667.2 July 12, 2012