Tel : Fax : email : +44 118 979 1238 +44 118 979 1283 info@actcrystals.com ACT9300SSC The ACT9300SSC is housed in a miniature, low profile SMD package, with a ceramic base utilising a seam welded metal lid for high reliability and better long-term stability. Spread Spectrum Technology is employed to assist with EMI emission reductions. This 5x3.2mm device is available with CMOS output with a supply voltage of 3.3V. Taped and reeled packaging (1K reels, 16mm tape) and loose quantities are available for purchase, to suit high and low volume production. Other Spread Spectrum devices available in DIL14 and 9.6x11.4x2.5 on request. Tri-state on pin 1 is available for the 1.0 and 3.0% options. SPECIFICATION Parameter Symbol Supply Voltage VDD Frequency Range fo Frequency Stability Specification Condition 3.3VDC 5% 6.000 ~160.0 MHz Please specify f/fo 25ppm, 50ppm or 100ppm Please specify Temp Operating Range Topr 0 ~ +70C or -40 ~ +85C Please specify Temp Storage Range Tstg -65 to +150C Iop 7mA (10MHz) 8mA (32.768MHz) 17mA (75MHz) 18mA (125MHz) Operating Current Freq Dependant Total % Down Spread % Centre Spread % (c) or Centre spread need to be 0.5# -0.5# 0.25# Specified when ordering.** 1.0 -1 0.5 Tolerance 2% of Total% 3.0 -3% 1.5 Spread Percentage Down spread -7dBc 100MHz at C=0.25# -9dBc min 100MHz at C=0.5 -15dBc min 100MHz at C=1.5 EMI Reduction 6.9KHz min, 55.5KHz max Modulation Carrier Frequency Duty Cycle Tw/t 45/55% Output Level `0' VOL 0.8V max 0.2 V typical (at 10% VDD) Output Level `1' VOH 2.0V min 3.2V typical (at 90% VDD) Rise & Fall Time (max) TrTf 4.0nS max (10%VDD to 90%VDD) Output Load N/CL 15pF CMOS Start-up Time Tosc 5mS max, 2mS Typical Please specify # Tri State not available. dBc: with respect to EMI level with no modulation. See examples Dependant on frequency CL=15pF: @50%VDD 40 ohms typical Output Impedance Tri-state# Tri state: output when low. Disable time 100nS max >2000V Static discharge Voltage 100K int'l pull up resistor MIL STD 883 Method 3015 Ageing Fa 5ppm first year max @25C Cycle to Cycle Jitter Tj 250pS typical, 300pS max for 13 MHz Oscillator Notes: **For initial design samples centre spread 1.5% is recommended. # Tri state not available on 0.5% total spread versions. Please note that all parameters can not necessarily be specified in the same device Customer to Specify : Frequency, Frequency Stability, Operating Temperature Range, Centre or down Spread, Spread Percentage In line with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com Issue:2 M6 Date:26/10/05 1 of 6 Tel : Fax : email : +44 118 979 1238 +44 118 979 1283 info@actcrystals.com ACT9300SSC Pad surface material Au Spread Spectrum principle: Down Spread Centre Spread In line with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com 2 of 6 Issue:2 M6 Date:26/10/05 Tel : Fax : email : +44 118 979 1238 +44 118 979 1283 info@actcrystals.com ACT9300SSC Spread Spectrum principle (continued from page 2) Spread Spectrum Clock (SSC), the mode energy of a spread spectrum clock is spread over a wider bandwidth, resulting from the frequency modulation technique. The modulation carrier frequency is in the KHz range which makes the modulation process transparent to the oscillator frequency. The controlled modulation process can be on all of one side of the nominal frequency (DOWN SPREAD) or equally spread either side of the nominal frequency (CENTRE SPREAD) . If OVER-CLOCKING is a problem to the system then the down spread is preferred. Instantaneous Frequencies (100MHz Nominal Frequency) Total Spread % 0.5% 1% 3% Down Spread Centre Spread Min Max Min Max Down Range Down Range Up Range Up Range -1.0% 0% -0.25% +0.25% -5000ppm 0ppm -2500ppm +2500ppm 99.750000 100.250000 100.000000 99.500000 Note. Tri State not available with 0.5% versions. 0% +0.5% -0.5% -1.0% -10000ppm 0ppm -5000ppm +5000ppm 99.000000 100.000000 99.500000 100.500000 0% -1.5% +1.5% -3.0% -30000ppm 0ppm -15000ppm +15.000ppm 97.000000 100.000000 98.500000 101.500000 EMI Reduction Data Main mode: EMI reduction: 10Log % x frequency (fo) ( Total spread 0.12 ) 10Log ( Total spread % x frequency(fo)x3 0.12 ) dB 10Log ( Total spread % x frequency(fo)x5 0.12 ) dB dB 3rd Harmonic: EMI reduction: 5th Harmonic: EMI reduction: In line with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com Issue:2 M6 Date:26/10/05 3 of 6 Tel : Fax : email : +44 118 979 1238 +44 118 979 1283 info@actcrystals.com ACT9300SSC EMI Example Test Data Nominal Frequency 100MHz Modulation Carrier 34.678KHz Example Whole Spectrum EMI Data 100MHz In line with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com Issue:2 M6 Date:26/10/05 4 of 6 Tel : Fax : email : +44 118 979 1238 +44 118 979 1283 info@actcrystals.com ACT9300SSC 13.1dBc EMI reduction ACT9300SSC REFLOW SPECIFICATION In line with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com Issue:2 M6 Date:26/10/05 5 of 6 Tel : Fax : email : ACT9300SSC +44 118 979 1238 +44 118 979 1283 info@actcrystals.com TAPE & REEL SPECIFICATIONS REEL A 180 B0.5 2.2 D1.0 20.2 C0.2 13 N1.0 62 T0.1 16.5 G2.0 20.5 mm TAPE A0.1 5.5 B0.1 3.8 C0.1 1.8 D1.0 8.0 E0.1 16.0 F0.1 4.0 G0.05 2.0 H+0.1-0 1.5 mm In line with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com Issue:2 M6 Date:26/10/05 6 of 6