060-2443-08 - Honeywell Test & Measurement

Subminiature Load Cell

Model 13

DESCRIPTION

Model 13 (compression only) subminiature load cell is designed

to measure load ranges from 150 g to 1000 lb. With subminiature

dimensions, including diameters from 0.38 in to 0.75 in and

heights of 0.13 in to 0.25 in, these units are easily incorporated

into systems having limited space. Model 13 combines high

frequency response and low deﬂection to achieve a combined

non-linearity and hysteresis of 0.25 % to 0.5 % full scale. A

balance module is included in the load cell’s lead wire cable for

temperature compensation and should not be removed.

FEATURES

• 150gto1000lb

• 0.7%accuracy

• mV/Voutput

• Subminiaturedesign

• Singlediaphragmconstruction

2Honeywell•SensingandControl

Model 13

PERFORMANCE SPECIFICATIONS

Characteristic Measure

Load ranges6150 g, 250 g, 500 g, 1000 g, 5 lb,

10 lb, 25 lb, 50 lb, 100 lb, 250 lb, 500 lb,

1000 lb

Linearity ±0.5 % full scale

Hysteresis ±0.5 % full scale

Non-repeatability ±0.1 % full scale

Tolerance on output

150 g to 500 g 15mV/V(nominal)

Tolerance on output 1000 g 1.5mV/V(nominal)

Tolerance on output

5 lb to 1000 lb 2mV/V(nominal)

Operation Compressiononly

Resolution Inﬁnite

RANGE CODES

Range codes Range

AL 150 g

AN 250 g

AP 500 g

AR 1000 g

AT 5 lb

AV 10 lb

BL 25 lb

BN 50 lb

BR 100 lb

CN 250 lb

CR 500 lb

CV 1000 lb

ELECTRICAL SPECIFICATIONS

Characteristic Measure

Straingagetype

150 g to 500 g

Semiconductor

Straingagetype

1000 g to 1000 lb

Bonded foil

Excitation (calibration) 5Vdc

Insulation resistance 5000mOhm@50Vdc

Bridge resistance (toler-

ance)150 g to 500 g

500 ohm (nominal)

Bridge resistance (toler-

ance)1000 g to 1000 lb

350 ohm (nominal)

Zero balance (tolerance) ±3 % of full scale (nominal)

Shuntcalibrationdata Included

Electrical termination (std) 1,83 m [5 ft] integral cable with balance

board3

MECHANICAL SPECIFICATIONS

Characteristic Measure

Maximum allowable load Seetable

Weight Seetable

Material Stainlesssteel

Deﬂection @ full scale Seetable

WIRING CODES

Cable Unamplied

Red (+) excitation

Black (-) excitation

Green (-) output

White (+) output

DEFLECTIONS AND RINGING FREQUENCIES

Capac-

ity (lb)

Deec-

tion at

full scale

(10-3 in)

Weight Weight with

cable

Max. al-

lowable

load1 (%

FS)

150 g 0.06 1 g [0.002 lb] 9 g [0.019 lb] 500

250 g 0.06 1 g [0.002 lb] 9 g [0.019 lb] 500

500 g 0.08 1 g [0.002 lb] 9 g [0.019 lb] 500

1000 g 0.05 1 g [0.002 lb] 9 g [0.019 lb] 150

5 lb 0.5 1 g [0.002 lb] 9 g [0.019 lb] 150

10 lb 0.4 1 g [0.002 lb] 9 g [0.019 lb] 150

25 lb 0.4 1 g [0.002 lb] 9 g [0.019 lb] 150

50 lb 0.4 1 g [0.002 lb] 9 g [0.019 lb] 150

100 lb 0.4 3 g [0.006 lb] 11 g [0.024 lb] 150

250 lb 0.5 3 g [0.006 lb] 11 g [0.024 lb] 150

500 lb 0.5 10 g [0.022 lb] 18 g [0.039 lb] 150

1000 lb 0.6 10 g [0.022 lb] 18 g [0.039 lb] 150

ENVIRONMENTAL SPECIFICATIONS

Characteristic Measure

Temperature, operating -54°Cto121°C[-65°Fto250°F]

Temperature, compensated 15°Cto71°C[60°Fto160°F]

Temperature effect, zero 0.01%fullscale/°F

Temperature effect, span 0.02%reading/°F

Honeywell•SensingandControl3

Subminiature Load Cell

MOUNTING DIMENSIONS

Ranges D1 D2 H B SR

150, 250, 500,

1000 g; 5, 10, 25, 50 lb

2,29 mm [0.09 in] 9,65 mm [0.38 in] 3,3 mm [0.13 in] 0,69 mm [0.027 in] 6,35 mm [0.25 in]

100, 250 lb 3,05 mm [0.12] 12,7 mm [0.50 in] 3,81 mm [0.15 in] 0,51 mm [0.020 in] 12,7 mm [0.50 in]

500 lb, 1000 lb 6,35 mm [0.25 in] 19,05 mm [0.75] 6,35 mm [0.25 in] 0,64 mm [0.025 in] 12,7 mm [0.50 in]

OPTION CODES

Many range/option combinations are available in

our quick-ship and fast-track manufacture pro-

grams. Please see http://sensing.honeywell.com/

TMsensor-ship for updated listings.

Load range 150, 250, 500 g,

1000 g; 5, 10, 25, 50, 100, 250, 500, 1000 lb

Temperature

compensa-

tion

1a.60°Fto160°F

1b.30°Fto130°F

1c.0°Fto185°F

1d.-20°Fto200°F

1e.-20°Fto200°F

1j.0°Cto50°C

1k.-20°Cto85°C

1m.-25°to110°C

Internal

ampliers

2u.Unamplied,mV/Voutput

Overload

stops

4a. Overload stops

Electrical

termination

5 ft integral cable with balance board3

6v. Phoenix connector on end of cable

15d.Connectoronendofcable

Special

calibration

9a.10point(5up/5down)20%increments@68°F

9b.20point(10up/10down)10%increments@68

°F

Shock and

vibration

44a.Shockandvibrationresistance

TYPICAL SYSTEM DIAGRAM

008641-2-EN IL50 GLO

April 2009

Model 13 Subminiature Load Cell

Sensing and Control

Honeywell

1985 Douglas Drive North

Golden Valley, MN 55422

www.honeywell.com

NOTES

1. Allowable maximum loads – maximum load to be applied without

damage.2 Loads described allow for 100 % full scale axial loading

with the bending loads speciﬁed. Torque loading maximum is with-

outaxialorotherload.Foranyothercombination,consultfactory.

2. Without damage - loading to this level will not cause excessive zero

shift or performance degradation. The user must consider fatigue

life for long term use and structural integrity. All structurally critical

applications (overhead loading, etc.) should always be designed

with safety redundant load paths.

3. A small, 2 in circuit board is included in the cable, 2 ft from the load

cell. Do not remove this board.

4. Only for ranges greater-than-or-equal-to 1000 g.

5. Specicationsmayvarywiththisoption.

6. This unit calibrated to Imperial (non-Metric) units.

Warranty. Honeywell warrants goods of its manufacture as

being free of defective materials and faulty workmanship.

Honeywell’s standard product warranty applies unless agreed

to otherwise by Honeywell in writing; please refer to your

order acknowledgement or consult your local sales ofﬁce for

speciﬁc warranty details. If warranted goods are returned to

Honeywell during the period of coverage, Honeywell will repair

or replace, at its option, without charge those items it ﬁnds

defective. The foregoing is buyer’s sole remedy and is in lieu

of all warranties, expressed or implied, including those of

merchantability and tness for a particular purpose. In no

event shall Honeywell be liable for consequential, special, or

indirect damages.

While we provide application assistance personally, through our

literature and the Honeywell web site, it is up to the customer to

determine the suitability of the product in the application.

WARNING

PERSONAL INJURY

•DONOTUSEtheseproductsassafetyoremergency

stop devices or in any other application where failure of

the product could result in personal injury.

Failure to comply with these instructions could result in

death or serious injury.

WARNING

MISUSE OF DOCUMENTATION

•Theinformationpresentedinthisdatasheetisfor

referenceonly.DONOTUSEthisdocumentasproduct

installation information.

•Completeinstallation,operationandmaintenance

information is provided in the instructions supplied with

each product.

Failure to comply with these instructions could result in

death or serious injury.

Find out more

Honeywell serves its customers

through a worldwide network of

sales ofﬁces, representatives

anddistributors.Forapplication

assistance, current speciﬁca-

tions, pricing or name of the

nearest Authorized Distributor,

contact your local sales ofﬁce.

To learn more about Honeywell’s

test and measurement products,

call +1-614-850-5000, visit

www.honeywell.com/sensotec,

or e-mail inquiries to

info.tm@honeywell.com

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Honeywell:

060-2444-03 060-2443-08 060-2445-04 060-2443-02 060-2443-07 060-2444-06 060-2443-06