FEATURES TYPICAL APPLICATIONS CIRCUITS L1 Adjustable and fixed current-limit options Adjustable up to 4 A Fixed 3 A 2.5 V to 5.5 V input voltage range 650 kHz or 1.3 MHz fixed frequency option Adjustable output voltage, up to 20 V Adjustable soft start Undervoltage lockout Thermal shutdown 3 mm x 3 mm, 10-lead LFCSP Supported by ADIsimPower design tool ADP1614 ADJUSTABLE CURRENT LIMIT 8 VIN SW 6 VIN ON OFF D1 SW 7 3 R1 EN CIN VOUT FB 2 9 CLRES R2 10 SS APPLICATIONS COMP 1 GND GND EP CSS 4 5 11 COUT RCOMP CCOMP 10293-001 RCL Figure 1. Step-Up Regulator Configuration for Adjustable Current-Limit Options TFT LCD bias supplies Portable applications Industrial/instrumentation equipment L1 ADP1614 FIXED CURRENT LIMIT SW 6 VIN GENERAL DESCRIPTION 8 VIN 3 EN 9 FREQ 10 SS COMP 1 GND GND EP ON OFF The ADP1614 is a step-up, dc-to-dc switching converter with an integrated power switch capable of providing an output voltage as high as 20 V. The ADP1614 is available with a pin-adjustable current limit that is set via an external resistor with the boost switching frequency fixed to either 650 kHz or 1.3 MHz. Alternatively, the ADP1614 is also available with fixed 3 A current limit and a pin-selectable frequency. With a package height of 0.8 mm, the ADP1614 is optimal for space constrained applications, such as portable devices or thin film transistor (TFT) liquid crystal displays (LCDs). D1 SW 7 CIN VOUT R1 FB 2 1.3MHz 650kHz (DEFAULT) CSS 4 R2 5 11 RCOMP CCOMP COUT 10293-201 Data Sheet 650 kHz/1.3 MHz, 4 A, Step-Up, PWM, DC-to-DC Switching Converter ADP1614 Figure 2. Step-Up Regulator Configuration for Fixed Current-Limit Options The ADP1614 operates in current-mode pulse-width modulation (PWM) with up to 94% efficiency. Adjustable soft start prevents inrush currents when the part is enabled. The PWM current-mode architecture allows excellent transient response, easy noise filtering, and the use of small, cost-saving external inductors and capacitors. Other key features include undervoltage lockout (UVLO), thermal shutdown (TSD), and logic controlled enable. The ADP1614 is available in a Pb-free, 10-lead lead frame chip scale package (LFCSP). Rev. B Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2012-2014 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADP1614 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Soft Start ...................................................................................... 13 Applications ....................................................................................... 1 Thermal Shutdown (TSD) ........................................................ 13 General Description ......................................................................... 1 Undervoltage Lockout (UVLO) ............................................... 13 Typical Applications Circuits .......................................................... 1 Shutdown Mode ......................................................................... 13 Revision History ............................................................................... 2 Applications Information .............................................................. 14 Specifications..................................................................................... 3 ADIsimPower Design Tool ....................................................... 14 Absolute Maximum Ratings............................................................ 5 Setting the Output Voltage ........................................................ 14 Thermal Resistance ...................................................................... 5 Inductor Selection ...................................................................... 14 ESD Caution .................................................................................. 5 Choosing the Input and Output Capacitors ........................... 15 Pin Configuration and Function Descriptions ............................. 6 Diode Selection........................................................................... 15 Typical Performance Characteristics ............................................. 7 Loop Compensation .................................................................. 15 Theory of Operation ...................................................................... 12 Soft Start Capacitor .................................................................... 16 Current-Mode PWM Operation .............................................. 13 PCB Layout Guidelines .................................................................. 17 Adjustable Current Limit .......................................................... 13 Outline Dimensions ....................................................................... 18 Frequency Selection ................................................................... 13 Ordering Guide .......................................................................... 18 REVISION HISTORY 11/14--Rev. A to Rev. B Changes to Ordering Guide .......................................................... 18 6/13--Rev. 0 to Rev. A Changes to Features Section, General Description Section, and Figure 1 .............................................................................................. 1 Added Figure 2; Renumbered Sequentially .................................. 1 Changes to Table 1 ............................................................................ 3 Added FREQ Pin to Table 2 ............................................................ 5 Changes to Pin 9 ............................................................................... 6 Added Figure 26 and Figure 27..................................................... 10 Added Figure 28 to Figure 31........................................................ 11 Changes to Theory of Operation Section and Figure 32........... 12 Changes to Adjustable Current Limit Section and Frequency Selection Section ............................................................................. 13 Changes to Figure 35 and Figure 36 Captions ............................ 17 Updated Outline Dimensions ....................................................... 18 Changes to Ordering Guide .......................................................... 18 6/12--Revision 0: Initial Version Rev. B | Page 2 of 18 Data Sheet ADP1614 SPECIFICATIONS VIN = 3.6 V, unless otherwise noted. Minimum and maximum values are guaranteed for TJ = -40C to +125C. Typical values specified are at TJ = 25C. All limits at temperature extremes are guaranteed by correlation and characterization using standard statistical quality control (SQC), unless otherwise noted. Table 1. Parameter SUPPLY Input Voltage Quiescent Current Shutdown Nonswitching State Switching State1 Symbol VIN IQSHDN IQ IQSW UNDERVOLTAGE LOCKOUT (UVLO) Undervoltage Lockout Threshold OUTPUT Output Voltage2 Load Regulation REFERENCE Feedback Voltage Line Regulation ERROR AMPLIFIER Transconductance Voltage Gain FB Pin Bias Current SWITCH (SW) On Resistance Adjustable Peak Current Limit3 Maximum Adjustable Peak Current Limit2 Fixed Peak Current Limit3 SW Pin Leakage Current CLRES VOLTAGE4 OSCILLATOR Oscillator Frequency Maximum Duty Cycle EN/FREQ LOGIC THRESHOLD Input Voltage Low Input Voltage High EN Pin Leakage Current FREQ Pin Leakage Current SOFT START (SS) Charging Current SS Pin Voltage Test Conditions/Comments Min 2.5 VIN rising VIN falling 2.33 2.20 2.5 V V 20 0.005 V mV/mA 1.2445 1.2650 0.02 0.2 V %/V 150 80 1 A/V dB nA 2.0 VIN 1.2250 I = 4 A VFB = 1.245 V VIL VIH IEN ISS VSS V A A mA mA VIN = 2.5 V to 5.5 V DMAX 5.5 1.5 1100 7 4.5 VFB fSW Unit 0.25 700 5.5 3 VOUT = 10 V, ILOAD = 1 mA to 1 A RDSON Max VEN = 0 V, VSW = GND VFB = 1.3 V, VSW = GND, fSW = 1.3 MHz and 650 kHz fSW = 1.3 MHz, VSW = GND, no load fSW = 650 kHz, VSW = GND, no load VOUT GMEA AV Typ ISW = 1.0 A RCL = 154 k, duty cycle = 70% RCL = 61.9 k, VIN = 3.6 V, VOUT = 15 V 0.95 50 50 1.30 4 100 1.65 m A A ADP1614ACPZ-R7 only, duty cycle = 70% VSW = 20 V ADP1614ACPZ-650-R7 and ADP1614ACPZ-1.3-R7 ICLRES = 5 A ICLRES = 20 A 2.50 3.10 0.1 3.60 10 A A 1.225 1.18 1.27 1.22 1.315 1.25 V V ADP1614ACPZ-1.3-R7 and ADP1614ACPZ-R7, VFREQ 1.6 V ADP1614ACPZ-650-R7 and ADP1614ACPZ-R7, VFREQ 0.3 V COMP = open, VFB = 1 V, fSW = 1.3 MHz and 650 kHz FREQ pin is ADP1614ACPZ-R7 only VIN = 2.5 V to 5.5 V VIN = 2.5 V to 5.5 V VEN = 3.6 V VFREQ = 3.6 V, VFB = 1.3 V 1.1 500 88 1.3 650 92 1.4 720 MHz kHz % 0.3 VSS = 0 V VFB = 1.3 V 3.4 1.17 Rev. B | Page 3 of 18 3.4 0.005 7 1 V V A A 5.5 1.23 7 1.29 A V 1.6 ADP1614 Parameter THERMAL SHUTDOWN Thermal Shutdown Threshold Thermal Shutdown Hysteresis Data Sheet Symbol Test Conditions/Comments Min Typ 150 20 Max Unit C C This parameter specifies the average current when the device switches internally with the SW pins (Pin 6 and Pin 7) grounded. Guaranteed by design. Current limit is a function of duty cycle. For the adjustable current limit versions, it is also a function of the resistor on the CLRES pin. See Figure 10 through Figure 13. 4 The CLRES pin cannot be controlled with a current source. An equivalent resistance should be used. 1 2 3 Rev. B | Page 4 of 18 Data Sheet ADP1614 ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 2. Parameter VIN, EN, FB, FREQ to GND CLRES to GND COMP to GND SS to GND SW to GND Operating Junction Temperature Range Storage Temperature Range Soldering Conditions Rating -0.3 V to +6 V -0.3 V to VIN 1.0 V to 1.6 V -0.3 V to +1.3 V 21 V -40C to +125C -65C to +150C JEDEC J-STD-020 Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Absolute maximum ratings apply individually only, not in combination. The junction-to-ambient thermal resistance (JA) of the package is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. The JA is highly dependent on the application and board layout. In applications where high maximum power dissipation exists, attention to thermal board design is required. The value of JA may vary, depending on the printed circuit board (PCB) material, layout, and environmental conditions. The boundary conditions for the thermal resistance of the ADP1614 are modeled under natural convection cooling at 25C ambient temperature, JESD 51-9, and 1 W power input on a 4-layer board. Table 3. Thermal Resistance1 Package Type 10-Lead LFCSP 1 JA 47 Thermal numbers per JEDEC standard JESD 51-9. ESD CAUTION Rev. B | Page 5 of 18 JC 7.22 Unit C/W ADP1614 Data Sheet PIN CONFIGURATION AND FUNCTION DESCRIPTIONS COMP 1 ADP1614 9 CLRES/FREQ EN 3 TOP VIEW (Not to Scale) 8 VIN GND 4 7 SW GND 5 6 SW NOTES 1. THE EXPOSED PAD IS NOT ELECTRICALLY CONNECTED; CONNECT THIS PAD TO A GROUND PLANE FOR BETTER HEAT DISTRIBUTION. 10293-002 10 SS FB 2 Figure 3. Pin Configuration Table 4. Pin Function Descriptions Pin No. 1 Mnemonic COMP 2 FB 3 4, 5 6, 7 EN GND SW 8 VIN 9 CLRES/FREQ 10 SS 11 EP Description Compensation Input. Connect a series resistor-capacitor network from COMP to GND to compensate the regulator. Output Voltage Feedback Input. Connect a resistive voltage divider from the output voltage to FB to set the regulator output voltage. Enable Input. Drive EN low to shut down the regulator; drive EN high to turn on the regulator. Ground. Switching Output. Connect the power inductor from the input voltage to SW and connect the external rectifier from SW to the output voltage to complete the step-up converter. Main Power Supply Input. VIN powers the ADP1614 internal circuitry. Connect VIN to the input source voltage. Bypass VIN to GND with a 10 F or greater capacitor as close to the ADP1614 as possible. Current-Limit Resistor (CLRES). Connect a resistor to GND to set the peak inductor current. Frequency Setting Input (FREQ). Connect FREQ to GND to program the oscillator to 650 kHz, or connect FREQ to VIN to program it to 1.3 MHz. Do not leave this pin floating. Soft Start. A capacitor connected from SS to GND brings up the output slowly at power-up and reduces inrush current. Exposed Die Attach Pad. The exposed pad is not electrically connected; connect this pad to a ground plane for better heat distribution. Rev. B | Page 6 of 18 Data Sheet ADP1614 TYPICAL PERFORMANCE CHARACTERISTICS 100 100 VIN = 5V fSW = 1.3MHz RCL = 71.5k 90 90 80 80 70 70 EFFICIENCY (%) 60 50 40 30 40 20 1 10 100 1k 10k LOAD CURRENT (mA) ADP1614ACPZ-1.3-R7 0 10293-003 0 VOUT = 10V VOUT = 15V VOUT = 20V 10 1 10 100 1k 10k LOAD CURRENT (mA) Figure 4. Efficiency vs. Load Current, VIN = 3.6 V, fSW = 650 kHz 10293-006 VOUT = 5V VOUT = 10V VOUT = 15V VIN = 3.6V fSW = 650kHz RCL = 71.5k 10 Figure 7. Efficiency vs. Load Current, VIN = 5 V, fSW = 1.3 MHz 100 4.0 VIN = 3.6V fSW = 1.3MHz RCL = 71.5k 80 70 60 50 40 30 20 VOUT = 5V VOUT = 10V VOUT = 15V 10 100 1k 10k LOAD CURRENT (mA) VIN = 4.5V 2.5 2.0 VIN = 3.5V 1.5 1.0 VIN = 2.5V VOUT = 5V 0 60 75 90 105 120 135 150 RCL (k) 10293-100 ADP1614ACPZ-1.3-R7 0 3.0 0.5 10293-004 10 1 ADP1614ACPZ-650-R7 ADP1614ACPZ-1.3-R7 3.5 MAXIMUM OUTPUT CURRENT (A) 90 EFFICIENCY (%) 50 30 20 Figure 8. Typical Maximum Continuous Output Current vs. RCL, VOUT = 5 V Figure 5. Efficiency vs. Load Current, VIN = 3.6 V, fSW = 1.3 MHz 100 1.4 VIN = 5V fSW = 650kHz RCL = 71.5k ADP1614ACPZ-650-R7 ADP1614ACPZ-1.3-R7 1.2 MAXIMUM OUTPUT CURRENT (A) 90 80 70 60 50 40 30 20 VOUT = 10V VOUT = 15V VOUT = 20V 10 ADP1614ACPZ-650-R7 0 1 10 100 1k 10k LOAD CURRENT (mA) Figure 6. Efficiency vs. Load Current, VIN = 5 V, fSW = 650 kHz 1.0 VIN = 5.5V 0.8 VIN = 4.5V 0.6 VIN = 3.5V 0.4 0.2 VOUT = 15V 0 60 75 10293-005 EFFICIENCY (%) 60 VIN = 2.5V 90 105 RCL (k) 120 135 150 10293-101 EFFICIENCY (%) ADP1614ACPZ-650-R7 Figure 9. Typical Maximum Continuous Output Current vs. RCL, VOUT = 15 V Rev. B | Page 7 of 18 ADP1614 Data Sheet 4.0 3.60 ADP1614ACPZ-650-R7 ADP1614ACPZ-1.3-R7 VIN = 4.5V TA = -40C 3.5 3.50 VIN = 2.5V TA = +25C CURRENT LIMIT (A) CURRENT LIMIT (A) ADP1614ACPZ-650-R7 ADP1614ACPZ-1.3-R7 3.55 3.0 2.5 VIN = 3.5V 2.0 3.45 3.40 TA = +85C 3.35 3.30 3.25 3.20 V OUT = 15V RCL = 71.5k 3.15 2.5 3.0 75 90 105 120 135 150 RCL (k) Figure 10. Peak Current Limit of Switch vs. RCL, VOUT = 5 V 3.5 4.0 4.0 4.5 Figure 13. Peak Current Limit of Switch vs. VIN over Temperature, VOUT = 15 V 3.90 80 ISW = 1A ADP1614ACPZ-650-R7 ADP1614ACPZ-1.3-R7 SWITCH ON RESISTANCE (m) CURRENT LIMIT (A) 3.85 3.80 TA = +85C 3.75 3.70 TA = +25C 3.65 TA = +125C 60 50 TA = +25C 40 3.0 3.5 4.0 TA = -40C 4.5 INPUT VOLTAGE (V) 30 2.5 10293-102 3.60 2.5 70 TA = -40C VOUT = 5V RCL = 71.5k 5.5 INPUT VOLTAGE (V) 3.0 3.5 4.0 4.5 5.0 5.5 INPUT VOLTAGE (V) Figure 11. Peak Current Limit of Switch vs. VIN over Temperature, VOUT = 5 V 10293-008 1.0 60 10293-104 VOUT = 5V 10293-103 1.5 Figure 14. Switch On Resistance vs. Input Voltage 4.0 94.5 ADP1614ACPZ-650-R7 ADP1614ACPZ-1.3-R7 94.0 3.5 TA = +125C MAXIMUM DUTY CYCLE (%) 3.0 VIN = 3.5V VIN = 4.5V 2.5 VIN = 5.5V 2.0 1.5 93.5 93.0 TA = -40C TA = +25C 92.5 92.0 91.5 1.0 60 75 90 105 120 135 RCL (k) 150 Figure 12. Peak Current Limit of Switch vs. RCL, VOUT = 15 V 91.0 2.5 3.0 3.5 4.0 4.5 5.0 INPUT VOLTAGE (V) Figure 15. Maximum Duty Cycle vs. Input Voltage Rev. B | Page 8 of 18 5.5 10293-015 VOUT = 15V 10293-105 CURRENT LIMIT (A) VIN = 2.5V Data Sheet ADP1614 7 760 6 740 TA = +125C 700 680 TA = +25C 660 5 EN PIN CURRENT (A) 720 640 TA = +125C 4 3 TA = -40C 2 TA = -40C 620 TA = +25C 600 580 2.5 3.0 3.5 4.0 4.5 5.0 5.5 INPUT VOLTAGE (V) 0 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VIN = 2.5V 5.8 4.0 3.5 TA = +25C VIN = 5.5V SS PIN CURRENT (A) TA = +125C TA = -40C 3.0 5.6 VIN = 3.6V 5.4 5.2 2.5 3.0 3.5 4.0 4.5 5.0 5.5 INPUT VOLTAGE (V) 4.8 -40 20 50 80 110 TEMPERATURE (C) Figure 17. Switching Quiescent Current vs. Input Voltage, fSW = 650 kHz 9 -10 10293-017 5.0 10293-011 Figure 20. SS Pin Current vs. Temperature VIN = 3.6V VOUT = 15V ILOAD = 60 CSS = 68nF fSW = 1.3MHz fSW = 1.3MHz 8 OUTPUT VOLTAGE (5V/DIV) SWITCH VOLTAGE (10V/DIV) 7 TA = +125C 1 2 6 TA = -40C TA = +25C INDUCTOR CURRENT (500mA/DIV) 5 4 4 3 3.0 3.5 4.0 4.5 INPUT VOLTAGE (V) 5.0 5.5 10293-012 3 2.5 EN PIN VOLTAGE (5V/DIV) Figure 18. Switching Quiescent Current vs. Input Voltage, fSW = 1.3 MHz Rev. B | Page 9 of 18 TIME (4ms/DIV) Figure 21. Startup, CSS = 68 nF 10293-106 SWITCHING QUIESCENT CURRENT (mA) 1.5 Figure 19. EN Pin Current vs. EN Pin Voltage fSW = 650kHz 2.0 2.5 SWITCHING QUIESCENT CURRENT (mA) 1.0 EN PIN VOLTAGE (V) Figure 16. Nonswitching Quiescent Current vs. Input Voltage 4.5 0.5 10293-016 1 10293-009 NONSWITCHING QUIESCENT CURRENT (A) 780 ADP1614 Data Sheet VIN = 5V VOUT = 15V OUTPUT VOLTAGE (200mV/DIV) AC-COUPLED fSW = 1.3MHz L = 10H VIN = 3.6V VOUT = 5V OUTPUT VOLTAGE (100mV/DIV) fSW = 650kHz AC-COUPLED L = 4.7H LOAD CURRENT (50mA/DIV) TIME (200s/DIV) LOAD CURRENT (50mA/DIV) 3 10293-020 3 1 10293-023 1 TIME (200s/DIV) Figure 22. 50 mA to 150 mA Load Transient, VIN = 3.6 V, VOUT = 5 V, fSW = 650 kHz Figure 25. 50 mA to 150 mA Load Transient, VIN = 5 V, VOUT = 15 V, fSW = 1.3 MHz 100 VIN = 3.6V VOUT = 5V OUTPUT VOLTAGE (100mV/DIV) fSW = 1.3MHz AC-COUPLED L = 4.7H 90 VIN = 5V fSW = 650kHz ADP1614ACPZ-R7 80 1 EFFICIENCY (%) 70 60 50 VOUT = 8V VOUT = 12V 40 30 20 LOAD CURRENT (50mA/DIV) TIME (200s/DIV) 0 1m 10m 100m 1 10 LOAD CURRENT (A) Figure 23. 50 mA to 150 mA Load Transient, VIN = 3.6 V, VOUT = 5 V, fSW = 1.3 MHz 10293-126 10 10293-021 3 Figure 26. Efficiency vs. Load Current, VIN = 5 V, fSW = 650 kHz 100 VIN = 5V VOUT = 15V OUTPUT VOLTAGE (100mV/DIV) AC-COUPLED fSW = 650kHz L = 15H 90 80 1 VIN = 5V fSW = 1.3MHz ADP1614ACPZ-R7 EFFICIENCY (%) 70 60 VOUT = 8V VOUT = 12V 50 40 30 20 LOAD CURRENT (50mA/DIV) 0 1m 10m 100m 1 10 LOAD CURRENT (A) Figure 27. Efficiency vs. Load Current, VIN = 5 V, fSW = 1.3 MHz Figure 24. 50 mA to 150 mA Load Transient, VIN = 5 V, VOUT = 15 V, fSW = 650 kHz Rev. B | Page 10 of 18 10293-127 TIME (200s/DIV) 10 10293-022 3 Data Sheet ADP1614 1.7 660 fSW = 650kHz 650 SWITCHING FREQUENCY (kHz) 1.5 1.3 1.1 0.9 0.7 VOUT = 8V VOUT = 12V 0.3 2.5 3.0 3.5 4.0 4.5 5.0 640 620 610 600 590 5.5 INPUT VOLTAGE (V) 580 2.5 3.5 4.0 4.5 5.0 5.5 Figure 30. Frequency vs. Input Voltage, fSW = 650 kHz 1.30 3.30 fSW = 1.3MHz TA = -40C TA = +25C TA = +85C 3.20 1.28 SWITCHING FREQUENCY (MHz) 3.25 3.15 3.10 3.05 3.00 2.95 2.90 3.5 4.5 4.0 INPUT VOLTAGE (V) 5.0 5.5 10293-129 3.0 TA = -40C TA = +25C TA = +125C 1.24 1.22 1.20 1.18 VOUT = 12V ADP1614ACPZ-R7 2.80 2.5 1.26 Figure 29. Peak Current Limit of Switch vs. VIN over Temperature, VOUT = 12 V Rev. B | Page 11 of 18 1.16 2.5 3.0 3.5 4.0 4.5 5.0 INPUT VOLTAGE (V) Figure 31. Frequency vs. Input Voltage, fSW = 1.3 MHz 5.5 10293-131 CURRENT LIMIT (A) 3.0 INPUT VOLTAGE (V) Figure 28. Typical Maximum Continuous Output Current vs. VIN 2.85 TA = -40C TA = +25C TA = +125C 630 10293-130 0.5 10293-128 MAXIMUM OUTPUT CURRENT (A) ADP1614ACPZ-R7 ADP1614 Data Sheet THEORY OF OPERATION tiny external components. The switch current is monitored on a pulse-by-pulse basis to limit the current to the value set by the RCL resistor on the CLRES pin on the adjustable current-limit version or to 3 A typical on the fixed current-limit version. The ADP1614 current-mode, step-up switching converter boosts a 2.5 V to 5.5 V input voltage to an output voltage as high as 20 V. The internal switch allows a high output current, and the 650 kHz/1.3 MHz switching frequency allows the use of L1 VIN ADP1614ACPZ-R7 1.3MHz 650kHz CIN VIN 9 8 + VIN D COMPARATOR VOUT R1 PWM COMPARATOR ERROR AMPLIFIER FB 2 R2 A + CURRENT SENSING VOUT COUT 5.5A S UVLOREF VSS Q N1 R TSD COMPARATOR 5.5A 10 SW D1 VIN RCOMP SS 7 SW DREF UVLO COMPARATOR 1 CCOMP 6 OSCILLATOR VBG COMP FREQ DRIVER TSENSE SOFT START RESET TREF BG BAND GAP CSS AGND 1.1M ADP1614 AGND CLRES RCL 9 3 11 EN 4 EP 5 GND GND ON OFF NOTES 1. THE PORTIONS IN THE DASHED BOXES DISPLAY THE TWO POSSIBLE FUNCTIONALITIES OF PIN 9 ON THE ADP1614. Figure 32. Block Diagram with Step-Up Regulator Application Circuit Rev. B | Page 12 of 18 10293-024 ADP1614ACPZ-650-R7 AND ADP1614ACPZ-1.3-R7 Data Sheet ADP1614 CURRENT-MODE PWM OPERATION SOFT START The ADP1614 utilizes a current-mode PWM control scheme to regulate the output voltage over all load conditions. The output voltage is monitored at FB through a resistive voltage divider. The voltage at FB is compared with the internal 1.245 V reference by the internal transconductance error amplifier to create an error voltage at COMP. The current of the switch is internally measured and added to the stabilizing ramp. The resulting sum is compared with the error voltage at COMP to control the PWM modulator. This current-mode regulation system allows fast transient response while maintaining a stable output voltage. By selecting the proper resistor-capacitor network from COMP to GND, the regulator response is optimized for a wide range of input voltages, output voltages, and load conditions. To prevent input inrush current to the converter when the part is enabled, connect a capacitor from SS to GND to set the soft start period. After the ADP1614 is turned on, SS sources 5 A (typical) to the soft start capacitor (CSS) until it reaches 1.23 V at startup. As the soft start capacitor charges, it limits the peak current allowed by the part. By slowly charging the soft start capacitor, the input current ramps slowly to prevent it from overshooting excessively at startup. When the ADP1614 is disabled, the SS pin is internally shorted to GND to discharge the soft start capacitor. ADJUSTABLE CURRENT LIMIT A key feature of the ADP1614ACPZ-650-R7 and ADP1614ACPZ-1.3-R7 is a pin-adjustable peak current limit of up to 4 A (see Figure 10 to Figure 13 and Figure 33). This adjustable current limit allows the other external components to be selected specifically for the application. The current limit is set via an external resistor connected from Pin 9 (CLRES) to ground. For the ADP1614ACPZ-R7, the current limit is fixed at 3 A. 4.0 VIN = 3.5V CURRENT LIMIT (A) 3.5 3.0 VOUT = 5V 2.5 The ADP1614 includes TSD protection. If the die temperature exceeds 150C (typical), TSD turns off the NMOS power device, significantly reducing power dissipation in the device and preventing output voltage regulation. The NMOS power device remains off until the die temperature is reduced to 130C (typical). The soft start capacitor is discharged during TSD to ensure low output voltage overshoot and inrush currents when regulation resumes. UNDERVOLTAGE LOCKOUT (UVLO) If the input voltage is below the UVLO threshold, the ADP1614 automatically turns off the power switch and places the part into a low power consumption mode. This prevents potentially erratic operation at low input voltages and prevents the power device from turning on when the control circuitry cannot operate it. The UVLO levels have ~100 mV of hysteresis to ensure glitch-free startup. SHUTDOWN MODE VOUT = 15V 2.0 The EN pin turns the ADP1614 regulator on or off. Drive EN low to shut down the regulator and reduce the input current to 0.25 A (typical). Drive EN high to turn on the regulator. 75 90 105 120 135 RCL (k) 150 10293-007 1.5 1.0 60 THERMAL SHUTDOWN (TSD) Figure 33. Peak Current Limit of Switch vs. RCL FREQUENCY SELECTION The adjustable current-limit versions of the ADP1614 are internally programmed to operate at either 650 kHz or 1.3 MHz. Operation of the ADP1614 at 650 kHz (ADP1614ACPZ-650-R7) optimizes the efficiency of the device, whereas operation of the ADP1614 at 1.3 MHz (ADP1614ACPZ-1.3-R7) enables the device to be used with smaller external components. For the fixed current-limit version (ADP1614ACP-R7), the frequency is pin selectable via the FREQ Pin (Pin 9). Connect FREQ to GND for 650 kHz operation or connect FREQ to VIN for 1.3 MHz operation. Do not leave the FREQ pin floating. When the converter is in shutdown mode (EN 0.3 V), there is a dc path from the input to the output through the inductor and output rectifier. This causes the output voltage to remain slightly below the input voltage by the forward voltage of the rectifier, preventing the output voltage from dropping to ground when the regulator is shut down. Regardless of the state of the EN pin, when a voltage is applied to the VIN pin, a large current spike occurs due to the nonisolated path through the inductor and diode between VIN and VOUT. The high current is a result of the output capacitor charging. The peak value is dependent on the inductor, output capacitor, and any load active on the output of the regulator. Rev. B | Page 13 of 18 ADP1614 Data Sheet APPLICATIONS INFORMATION ADIsimPOWER DESIGN TOOL The ADP1614 is supported by the ADIsimPowerTM design toolset. ADIsimPower is a collection of tools that produce complete power designs that are optimized for a specific design goal. The tools enable the user to generate a full schematic and bill of materials and to calculate performance in minutes. ADIsimPower can optimize designs for cost, area, efficiency, and parts count while taking into consideration the operating conditions and limitations of the IC and the external components. For more information about the ADIsimPower design tools, visit www.analog.com/ADIsimPower. The toolset is available from this website, and users can request an unpopulated board. SETTING THE OUTPUT VOLTAGE The ADP1614 features an adjustable output voltage range of VIN to 20 V. The output voltage is set by the resistor voltage divider, R1 and R2 (see Figure 32), from the output voltage (VOUT) to the 1.245 V feedback input at FB. Use the following equation to determine the output voltage: VOUT = 1.245 x (1 + R1/R2) (1) Choose R1 based on the following equation: - 1.245 V R1 = R2 x OUT 1.245 (2) INDUCTOR SELECTION The inductor is an essential part of the step-up switching converter. It stores energy during the on time of the power switch and transfers that energy to the output through the output rectifier during the off time. To balance the trade-offs between small inductor current ripple and efficiency, inductance values in the range of 4.7 H to 22 H are recommended. In general, lower inductance values have higher saturation current and lower series resistance for a given physical size. However, lower inductance values result in higher peak current, which can lead to reduced efficiency and greater input and/or output ripple and noise. A peak-to-peak inductor ripple current close to 30% of the maximum dc input current typically yields an optimal compromise. For determining the inductor ripple current in continuous operation, the input (VIN) and output (VOUT) voltages determine the switch duty cycle (D) as follows: D= VOUT - VIN VOUT (3) The duty cycle and switching frequency (fSW) can be used to determine the on time: t ON = D f SW (4) The inductor ripple current (IL) in steady state is calculated by I L = VIN x t ON L (5) Solve for the inductance value (L) as follows: L= VIN x t ON (6) I L Ensure that the peak inductor current (the maximum input current plus half the inductor ripple current) is below the rated saturation current of the inductor. Likewise, make sure that the maximum rated rms current of the inductor is greater than the maximum dc input current to the regulator. For continuous current-mode (CCM) duty cycles greater than 50% that occur with input voltages less than one-half the output voltage, slope compensation is required to maintain stability of the current-mode regulator. For stable current-mode operation, ensure that the selected inductance is equal to or greater than the minimum calculated inductance, LMIN, for the application parameters in the following equation: L > LMIN = (VOUT - 2 x VIN ) 8 x f SW (7) Inductors smaller than the 4.7 H to 22 H recommended range can be used as long as Equation 7 is satisfied for the given application. For input/output combinations that approach the 90% maximum duty cycle, doubling the inductor is recommended to ensure stable operation. Table 5 suggests a series of inductors for use with the ADP1614. Table 5. Suggested Inductors Manufacturer Coilcraft TOKO Inc. Wurth Elektronik Vishay Dale TDK Components Taiyo Yuden Rev. B | Page 14 of 18 Part Series XAL40xx, XAL50xx, XAL6060, DO3316P FDV06xx, DG6045C, FDSD0630, DEM8045C, FDVE1040 WE-HCI, WE-TPC, WE-PD, WE-PD2, WE -PDF IHLP-2020, IHLP-2525, IHLP-3232, IHLP-4040 SPM6530, VLP8040, VLF10040, VLF10045 NRS8030, NRS8040 Data Sheet ADP1614 CHOOSING THE INPUT AND OUTPUT CAPACITORS The ADP1614 requires input and output bypass capacitors to supply transient currents while maintaining constant input and output voltages. Use low equivalent series resistance (ESR) capacitors of 10 F or greater to prevent noise at the ADP1614 input. Place the capacitor between VIN and GND, as close as possible to the ADP1614. Ceramic capacitors are preferable because of their low ESR characteristics. Alternatively, use a high value, medium ESR capacitor in parallel with a 0.1 F low ESR capacitor, placed as close as possible to the ADP1614. The output capacitor maintains the output voltage and supplies current to the load while the ADP1614 switch is on. The value and characteristics of the output capacitor greatly affect the output voltage ripple and stability of the regulator. A low ESR ceramic dielectric capacitor is preferable. The output voltage ripple (VOUT) is calculated as follows: VOUT = QC I xt = OUT ON C OUT C OUT (8) where: QC is the charge removed from the capacitor. COUT is the output capacitance. IOUT is the output load current. tON is the on time of the switch. diode is rated to handle the average output load current with the minimum duty cycle. The minimum duty cycle in CCM of the ADP1614 is D MIN = D f SW (9) (10) Choose the output capacitor based on the following equation: C OUT I OUT x (VOUT - VIN ) f SW x VOUT x VOUT * * * * ON Semiconductor Diodes, Inc. Toshiba ROHM Semiconductor LOOP COMPENSATION The ADP1614 uses external components to compensate the regulator loop, allowing optimization of the loop dynamics for a given application. The step-up converter produces an undesirable right-half plane zero in the regulation feedback loop. This requires compensating the regulator such that the crossover frequency occurs well below the frequency of the right-half plane zero. The right-half plane zero is determined by the following equation: DIODE SELECTION The output rectifier conducts the inductor current to the output capacitor and load while the switch is off. For high efficiency, minimize the forward voltage drop of the diode. For this reason, using Schottky rectifiers is recommended. However, for high voltage, high temperature applications, where the Schottky rectifier reverse leakage current becomes significant and can degrade efficiency, use an ultrafast junction diode. Many diode manufacturers derate the current capability of the diode as a function of the duty cycle. Verify that the output 2 R LOAD x 2 x L (13) where: FZ(RHP) is the right-half plane zero. RLOAD is the equivalent load resistance or the output voltage divided by the load current. To stabilize the regulator, ensure that the regulator crossover frequency is less than or equal to one-fifth of the right-half plane zero. The regulator loop gain is (11) Multilayer ceramic capacitors are recommended for this application. (12) The following are suggested Schottky diode manufacturers: V FZ (RHP ) = IN VOUT The input (VIN) and output (VOUT) voltages determine the switch duty cycle (D) as follows: - VIN V D = OUT VOUT VOUT where VIN(MAX) is the maximum input voltage. The on time of the switch is determined as follows: t ON = VOUT - VIN ( MAX ) AVL = V VFB x IN x G MEA x ROUT Z COMP x GCS x Z OUT (14) VOUT VOUT where: AVL is the loop gain. VFB is the feedback regulation voltage, 1.245 V. VOUT is the regulated output voltage. VIN is the input voltage. GMEA is the error amplifier transconductance gain. ROUT = 67 M. ZCOMP is the impedance of the series RC network from COMP to GND. GCS is the current sense transconductance gain (the inductor current divided by the voltage at COMP), which is internally set by the ADP1614. ZOUT is the impedance of the load in parallel with the output capacitor. Rev. B | Page 15 of 18 ADP1614 Data Sheet To determine the crossover frequency, it is important to note that at the crossover frequency the compensation impedance (ZCOMP) is dominated by a resistor, and the output impedance (ZOUT) is dominated by the impedance of an output capacitor. Therefore, when solving for the crossover frequency, the equation (by definition of the crossover frequency) is simplified to V VFB x IN x G MEA x RCOMP x GCS x VOUT VOUT 1 =1 2 x f C x C OUT AVL = (15) where: RCOMP is the compensation resistor. fC is the crossover frequency. Solve for C2 as follows: C2 = 2 x f C x C OUT x (VOUT ) 2 (16) VFB x VIN x G MEA x GCS where: VFB = 1.245 V. GMEA = 150 A/V. GCS = 7 A/V. 4806 x f C x C OUT x (VOUT ) = VIN 2 Upon startup (EN 1.6 V) or fault recovery, the voltage at SS ramps up slowly by charging the soft start capacitor (CSS) with an internal 5.5 A current source (ISS). As the soft start capacitor charges, it limits the peak current allowed by the part to prevent excessive overshoot at startup. Use the following equation to determine the necessary value of the soft start capacitor (CSS) for a specific overshoot and start-up time when the part is at the current limit with maximum load: 2 x f C x RCOMP (18) where CCOMP is the compensation capacitor. ERROR AMPLIFIER COMP FB 2 gm VBG C SS = I SS (17) After the compensation resistor is known, set the zero formed by the compensation capacitor and resistor to one-fourth of the crossover frequency, or C COMP = (19) If a low ESR, ceramic output capacitor is used for COUT, C2 is optional. For optimal transient performance, RCOMP and CCOMP might need to be adjusted by observing the load transient response of the ADP1614. For most applications, the compensation resistor should be within the range of 1 k to 100 k, and the compensation capacitor should be within the range of 100 pF to 10 nF. Therefore, RCOMP ESR x C OUT RCOMP SOFT START CAPACITOR Solve for RCOMP as follows: RCOMP = Capacitor C2 is chosen to cancel the zero introduced by the ESR of the output capacitor. 1 RCOMP CCOMP 10293-026 C2 t VSS (20) where: ISS = 5.5 A (typical). t is the start-up time at the current limit. VSS = 1.23 V (typical). If the applied load does not place the part at the current limit, the value of CSS can be reduced. A 68 nF soft start capacitor results in negligible input current overshoot at startup and, therefore, is suitable for most applications. If an unusually large output capacitor is used, a longer soft start period is required to prevent input inrush current. However, if fast startup is required, the soft start capacitor can be reduced or removed, which allows the ADP1614 to start quickly but with greater peak switch current. Figure 34. Compensation Components Rev. B | Page 16 of 18 Data Sheet ADP1614 PCB LAYOUT GUIDELINES For high efficiency, good regulation, and stability, a well designed PCB layout is required. * * * * * * * * Keep the low ESR input capacitor (CIN), which is labeled as C4 in Figure 35, close to VIN and GND. This minimizes noise injected into the part from board parasitic inductance. Keep the high current path from CIN through the L1 inductor to SW and GND as short as possible. Keep the high current path from VIN through the inductor (L1), the rectifier (D1), and the output capacitor (COUT), which is labeled as C7 in Figure 35, as short as possible. Keep high current traces as short and as wide as possible. Place the feedback resistors as close to FB as possible to prevent noise pickup. Connect the ground of the feedback network directly to an AGND plane that makes a Kelvin connection to the GND pin. Place the compensation components as close as possible to COMP. Connect the ground of the compensation network directly to an AGND plane that makes a Kelvin connection to the GND pin. Connect the soft start capacitor (CSS), which is labeled as C1 in Figure 35, as close as possible to the device. Connect the ground of the soft start capacitor to an AGND plane that makes a Kelvin connection to the GND pin. Connect the current-limit set resistor (RCL), which is labeled as R4 in Figure 35, as close as possible to the device. Connect the ground of the CL resistor to an AGND plane that makes a Kelvin connection to the GND pin. The PCB must be properly designed to conduct the heat away from the package. This is achieved by adding thermal vias to the PCB, which provide a thermal path to the inner or bottom layers. Thermal vias should be placed on the PCB underneath the exposed pad of the LFCSP and in the GND plane around the ADP1614 package to improve thermal performance of the package. Avoid routing high impedance traces from the compensation and feedback resistors near any node connected to SW or near the inductor to prevent radiated noise injection. Figure 35. ADP1614 Recommended Top Layer Layout for the Adjustable Current-Limit Boost Application 10293-028 * 10293-027 Use the following guidelines when designing PCBs (see Figure 32 for a block diagram and Figure 3 for a pin configuration). Figure 36. ADP1614 Recommended Bottom Layer Layout for the Adjustable Current-Limit Boost Application Rev. B | Page 17 of 18 ADP1614 Data Sheet OUTLINE DIMENSIONS 2.48 2.38 2.23 3.10 3.00 SQ 2.90 0.50 BSC 10 6 PIN 1 INDEX AREA 1.74 1.64 1.49 EXPOSED PAD 0.50 0.40 0.30 1 5 BOTTOM VIEW 0.80 0.75 0.70 SEATING PLANE 0.30 0.25 0.20 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 MIN PIN 1 INDICATOR (R 0.15) FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. 02-05-2013-C TOP VIEW 0.20 REF Figure 37. 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 3 mm x 3 mm Body, Very Very Thin, Dual Lead (CP-10-9) Dimensions shown in millimeters ORDERING GUIDE Model1 ADP1614ACPZ-1.3-R7 ADP1614ACPZ-650-R7 ADP1614ACPZ-R7 ADP1614-1.3-EVALZ ADP1614-650-EVALZ 1 Temperature Range -40C to +125C -40C to +125C -40C to +125C Switching Frequency 1.3 MHz 650 kHz Pin selectable 1.3 MHz Current Limit Adjustable up to 4 A Adjustable up to 4 A Fixed 3 A Adjustable up to 4 A 650 kHz Adjustable up to 4 A Z = RoHS Compliant Part. (c)2012-2014 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D10293-0-11/14(B) Rev. B | Page 18 of 18 Package Description 10-Lead LFCSP_WD 10-Lead LFCSP_WD 10-Lead LFCSP_WD Evaluation Board, 15 V Output Voltage Configuration Evaluation Board, 5 V Output Voltage Configuration Package Option CP-10-9 CP-10-9 CP-10-9 Branding LM4 LM5 LNG Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: ADP1614-1.3-EVALZ ADP1614-650-EVALZ ADP1614ACPZ-650-R7 ADP1614ACPZ-1.3-R7 ADP1614ACPZ-R7