M48T58 M48T58Y 5.0 V, 64 Kbit (8 Kb x 8) TIMEKEEPER(R) SRAM Features Integrated, ultra low power SRAM, real-time clock, power-fail control circuit and battery BYTEWIDETM RAM-like clock access BCD coded year, month, day, date, hours, minutes, and seconds Frequency test output for real-time clock Automatic power-fail chip deselect and WRITE protection WRITE protect voltages (VPFD = power-fail deselect voltage): - M48T58: VCC = 4.75 to 5.5 V; 4.5 V VPFD 4.75 V - M48T58Y: VCC = 4.5 to 5.5 V; 4.2 V VPFD 4.5 V 1 PCDIP28 Battery/crystal CAPHATTM SNAPHAT(R) Battery/crystal Self-contained battery and crystal in the CAPHATTM DIP package Packaging includes a 28-lead SOIC and SNAPHAT(R) top (to be ordered separately) SOIC package provides direct connection for a snaphat housing containing the battery and crystal Pin and function compatible with JEDEC standard 8 Kb x 8 SRAMs RoHS compliant - Lead-free second level interconnect June 2011 28 Doc ID 2412 Rev 8 28 1 SOH28 1/33 www.st.com 1 Contents M48T58, M48T58Y Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Operation modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3 READ mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4 WRITE mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5 Data retention mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6 Clock operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.1 Reading the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.2 Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.3 Stopping and starting the oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.4 Calibrating the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6.5 Battery low flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.6 Century bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.7 VCC noise and negative going transients . . . . . . . . . . . . . . . . . . . . . . . . . 20 7 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 8 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 9 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 10 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 11 Environmental information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 12 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 2/33 Doc ID 2412 Rev 8 M48T58, M48T58Y List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 READ mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 WRITE mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Operating and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 DC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Power down/up AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Power down/up trip points DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 PCDIP28 - 28-pin plastic DIP, battery CAPHATTM, package mech. data . . . . . . . . . . . . . 25 SOH28 - 28-lead plastic small outline, 4-socket battery SNAPHAT(R), package mech. data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 SH - 4-pin SNAPHAT(R) housing for 48 mAh battery & crystal, package mech. data . . . . . 27 SH - 4-pin SNAPHAT(R) housing for 120 mAh battery & crystal, package mech. data . . . . 28 Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 SNAPHAT(R) battery table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Doc ID 2412 Rev 8 3/33 List of figures M48T58, M48T58Y List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. 4/33 Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 DIP connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 SOIC connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 READ mode AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 WRITE enable controlled, WRITE AC waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Chip enable controlled, WRITE AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Crystal accuracy across temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Clock calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Supply voltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 AC measurement load circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Power down/up mode AC waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 PCDIP28 - 28-pin plastic DIP, battery CAPHATTM, package outline . . . . . . . . . . . . . . . . . 25 SOH28 - 28-lead plastic small outline, 4-socket battery SNAPHAT(R), package outline . . . 26 SH - 4-pin SNAPHAT(R) housing for 48 mAh battery & crystal, pack. outline . . . . . . . . . . . 27 SH - 4-pin SNAPHAT(R) housing for 120 mAh battery & crystal, package outline. . . . . . . . 28 Recycling symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Doc ID 2412 Rev 8 M48T58, M48T58Y 1 Description Description The M48T58/Y TIMEKEEPER(R) RAM is a 8 Kb x 8 non-volatile static RAM and real-time clock. The monolithic chip is available in two special packages to provide a highly integrated battery-backed memory and real-time clock solution. The M48T58/Y is a non-volatile pin and function equivalent to any JEDEC standard 8b Kb x 8 SRAM. It also easily fits into many ROM, EPROM, and EEPROM sockets, providing the non-volatility of PROMs without any requirement for special WRITE timing or limitations on the number of WRITEs that can be performed. The 28-pin, 600 mil DIP CAPHATTM houses the M48T58/Y silicon with a quartz crystal and a long life lithium button cell in a single package. The 28-pin, 330 mil SOIC provides sockets with gold plated contacts at both ends for direct connection to a separate SNAPHAT(R) housing containing the battery and crystal. The unique design allows the SNAPHAT battery package to be mounted on top of the SOIC package after the completion of the surface mount process. Insertion of the SNAPHAT housing after reflow prevents potential battery and crystal damage due to the high temperatures required for device surface-mounting. The SNAPHAT housing is keyed to prevent reverse insertion. The SOIC and battery/crystal packages are shipped separately in plastic anti-static tubes or in tape & reel form. For the 28-lead SOIC, the battery/crystal package (e.g., SNAPHAT) part number is "M4T28BR12SH". Figure 1. Logic diagram VCC 13 8 A0-A12 DQ0-DQ7 W E1 M48T58 M48T58Y FT E2 G VSS Doc ID 2412 Rev 8 AI01374B 5/33 Description M48T58, M48T58Y Table 1. Signal names A0-A12 DQ0-DQ7 Figure 2. Address inputs Data inputs / outputs FT Frequency test output (open drain) E1 Chip enable 1 E2 Chip enable 2 G Output enable W WRITE enable VCC Supply voltage VSS Ground DIP connections FT A12 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 VSS Figure 3. 28 1 27 2 26 3 4 25 24 5 23 6 7 M48T58 22 8 M48T58Y 21 20 9 19 10 11 18 12 17 13 16 14 15 VCC W E2 A8 A9 A11 G A10 E1 DQ7 DQ6 DQ5 DQ4 DQ3 AI01375B SOIC connections FT A12 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 VSS 1 28 27 2 26 3 25 4 24 5 23 6 22 7 M48T58Y 21 8 20 9 19 10 18 11 17 12 16 13 15 14 VCC W E2 A8 A9 A11 G A10 E1 DQ7 DQ6 DQ5 DQ4 DQ3 AI01376B 6/33 Doc ID 2412 Rev 8 M48T58, M48T58Y Figure 4. Description Block diagram FT OSCILLATOR AND CLOCK CHAIN 8 x 8 BiPORT SRAM ARRAY 32,768 Hz CRYSTAL A0-A12 POWER 8184 x 8 SRAM ARRAY LITHIUM CELL DQ0-DQ7 E1 VOLTAGE SENSE AND SWITCHING CIRCUITRY E2 VPFD VCC W G VSS Doc ID 2412 Rev 8 AI01377C 7/33 Operation modes 2 M48T58, M48T58Y Operation modes As Figure 4 on page 7 shows, the static memory array and the quartz controlled clock oscillator of the M48T58/Y are integrated on one silicon chip. The two circuits are interconnected at the upper eight memory locations to provide user accessible BYTEWIDETM clock information in the bytes with addresses 1FF8h-1FFFh. The clock locations contain the century, year, month, date, day, hour, minute, and second in 24 hour BCD format (except for the century). Corrections for 28, 29 (leap year - valid until 2100), 30, and 31 day months are made automatically. Byte 1FF8h is the clock control register. This byte controls user access to the clock information and also stores the clock calibration setting. The eight clock bytes are not the actual clock counters themselves; they are memory locations consisting of BiPORTTM READ/write memory cells. The M48T58/Y includes a clock control circuit which updates the clock bytes with current information once per second. The information can be accessed by the user in the same manner as any other location in the static memory array. The M48T58/Y also has its own power-fail detect circuit. The control circuitry constantly monitors the single 5 V supply for an out-of-tolerance condition. When VCC is out of tolerance, the circuit write protects the SRAM, providing a high degree of data security in the midst of unpredictable system operation brought on by low VCC. As VCC falls below the battery backup switchover voltage (VSO), the control circuitry connects the battery which maintains data and clock operation until valid power returns. Table 2. Mode Operating modes VCC Deselect Deselect WRITE READ 4.75 to 5.5 V or 4.5 to 5.5 V READ E1 E2 G W DQ0-DQ7 Power VIH X X X High Z Standby X VIL X X High Z Standby VIL VIH X VIL DIN Active VIL VIH VIL VIH DOUT Active VIL VIH VIH VIH High Z Active Deselect VSO to VPFD (min)(1) X X X X High Z CMOS standby Deselect VSO(1) X X X X High Z Battery backup mode 1. See Table 11 on page 24 for details. Note: 8/33 X = VIH or VIL; VSO = Battery backup switchover voltage. Doc ID 2412 Rev 8 M48T58, M48T58Y 3 READ mode READ mode The M48T58/Y is in the READ mode whenever W (WRITE enable) is high, E1 (chip enable 1) is low, and E2 (chip enable 2) is high. The unique address specified by the 13 address inputs defines which one of the 8,192 bytes of data is to be accessed. Valid data will be available at the data I/O pins within address access time (tAVQV) after the last address input signal is stable, providing that the E1, E2, and G access times are also satisfied. If the E1, E2 and G access times are not met, valid data will be available after the latter of the chip enable access times (tE1LQV or tE2HQV) or output enable access time (tGLQV). The state of the eight three-state data I/O signals is controlled by E1, E2 and G. If the outputs are activated before tAVQV, the data lines will be driven to an indeterminate state until tAVQV. If the address inputs are changed while E1, E2 and G remain active, output data will remain valid for output data hold time (tAXQX) but will go indeterminate until the next address access. Figure 5. READ mode AC waveforms tAVAV A0-A12 VALID tAVQV tAXQX tE1LQV tE1HQZ E1 tE1LQX tE2HQV tE2LQZ E2 tE2HQX tGLQV tGHQZ G tGLQX VALID DQ0-DQ7 AI00962 Note: WRITE enable (W) = high. Doc ID 2412 Rev 8 9/33 READ mode M48T58, M48T58Y Table 3. READ mode AC characteristics M48T58/Y Parameter(1) Symbol Unit Min Max tAVAV READ cycle time tAVQV Address valid to output valid 70 70 ns ns tE1LQV Chip enable 1 low to output valid 70 ns tE2HQV Chip enable 2 high to output valid 70 ns tGLQV Output enable low to output valid 35 ns tE1LQX(2) tE2HQX(2) tGLQX(2) tE1HQZ(2) tE2LQZ(2) tGHQZ(2) Chip enable 1 low to output transition 5 ns Chip enable 2 high to output transition 5 ns Output enable low to output transition 5 ns tAXQX Address transition to output transition Chip enable 1 high to output Hi-Z 25 ns Chip enable 2 low to output Hi-Z 25 ns Output enable high to output Hi-Z 25 ns 10 ns 1. Valid for ambient operating temperature: TA = 0 to 70 C; VCC = 4.75 to 5.5 V or 4.5 to 5.5 V (except where noted). 2. CL = 5 pF. 10/33 Doc ID 2412 Rev 8 M48T58, M48T58Y 4 WRITE mode WRITE mode The M48T58/Y is in the WRITE mode whenever W and E1 are low and E2 is high. The start of a WRITE is referenced from the latter occurring falling edge of W or E1, or the rising edge of E2. A WRITE is terminated by the earlier rising edge of W or E1, or the falling edge of E2. The addresses must be held valid throughout the cycle. E1 or W must return high or E2 low for a minimum of tE1HAX or tE2LAX from chip enable or tWHAX from WRITE enable prior to the initiation of another READ or WRITE cycle. Data-in must be valid tDVWH prior to the end of WRITE and remain valid for tWHDX afterward. G should be kept high during WRITE cycles to avoid bus contention; although, if the output bus has been activated by a low on E1 and G and a high on E2, a low on W will disable the outputs tWLQZ after W falls. Figure 6. WRITE enable controlled, WRITE AC waveform tAVAV VALID A0-A12 tAVWH tWHAX tAVE1L E1 tAVE2H E2 tWLWH tAVWL W tWHQX tWLQZ tWHDX DQ0-DQ7 DATA INPUT tDVWH Doc ID 2412 Rev 8 AI00963 11/33 WRITE mode Figure 7. M48T58, M48T58Y Chip enable controlled, WRITE AC waveforms tAVAV A0-A12 VALID tAVE1H tAVE1L tE1LE1H tE1HAX E1 tAVE2L tAVE2H tE2HE2L tE2LAX E2 tAVWL W tE1HDX tE2LDX DQ0-DQ7 DATA INPUT tDVE1H tDVE2L 12/33 Doc ID 2412 Rev 8 AI00964B M48T58, M48T58Y Table 4. Symbol WRITE mode WRITE mode AC characteristics M48T58/Y Parameter(1) Unit Min Max tAVAV WRITE cycle time 70 ns tAVWL Address valid to WRITE enable low 0 ns tAVE1L Address valid to chip enable 1 low 0 ns tAVE2H Address valid to chip enable 2 high 0 ns tWLWH WRITE enable pulse width 50 ns tE1LE1H Chip enable 1 low to chip enable 1 high 55 ns tE2HE2L Chip enable 2 high to chip enable 2 low 55 ns tWHAX WRITE enable high to address transition 0 ns tE1HAX Chip enable 1 high to address transition 0 ns tE2LAX Chip enable 2 low to address transition 0 ns tDVWH Input valid to WRITE enable high 30 ns tDVE1H Input valid to chip enable 1 high 30 ns tDVE2L Input valid to chip enable 2 low 30 ns tWHDX WRITE enable high to input transition 5 ns tE1HDX Chip enable 1 high to input transition 5 ns tE2LDX Chip enable 2 low to input transition 5 ns tWLQZ(2)(3) Write enable low to output Hi-Z 25 ns tAVWH Address valid to WRITE enable high 60 ns tAVE1H Address valid to chip enable 1 high 60 ns tAVE2L Address valid to chip enable 2 low 60 ns WRITE enable high to output transition 5 ns tWHQX(2)(3) 1. Valid for ambient operating temperature: TA = 0 to 70 C; VCC = 4.75 to 5.5 V or 4.5 to 5.5 V (except where noted). 2. CL = 5 pF. 3. If E1 goes low or E2 high simultaneously with W going low, the outputs remain in the high impedance state. Doc ID 2412 Rev 8 13/33 Data retention mode 5 M48T58, M48T58Y Data retention mode With valid VCC applied, the M48T58/Y operates as a conventional BYTEWIDETM static RAM. Should the supply voltage decay, the RAM will automatically power-fail deselect, write protecting itself when VCC falls within the VPFD (max), VPFD (min) window. All outputs become high impedance, and all inputs are treated as "don't care." Note: A power failure during a WRITE cycle may corrupt data at the currently addressed location, but does not jeopardize the rest of the RAM's content. At voltages below VPFD (min), the user can be assured the memory will be in a write protected state, provided the VCC fall time is not less than tF. The M48T58/Y may respond to transient noise spikes on VCC that reach into the deselect window during the time the device is sampling VCC. Therefore, decoupling of the power supply lines is recommended. When VCC drops below VSO, the control circuit switches power to the internal battery which preserves data and powers the clock. The internal button cell will maintain data in the M48T58/Y for an accumulated period of at least 7 years when VCC is less than VSO. As system power returns and VCC rises above VSO, the battery is disconnected, and the power supply is switched to external VCC. Write protection continues until VCC reaches VPFD (min) plus trec (min). E1 should be kept high or E2 low as VCC rises past VPFD (min) to prevent inadvertent WRITE cycles prior to system stabilization. Normal RAM operation can resume trec after VCC exceeds VPFD (max). For more information on battery storage life refer to the application note AN1012. 14/33 Doc ID 2412 Rev 8 M48T58, M48T58Y 6 Clock operations 6.1 Reading the clock Clock operations Updates to the TIMEKEEPER(R) registers (see Table 5) should be halted before clock data is read to prevent reading data in transition. The BiPORTTM TIMEKEEPER cells in the RAM array are only data registers and not the actual clock counters, so updating the registers can be halted without disturbing the clock itself. Updating is halted when a '1' is written to the READ bit, D6 in the control register 1FF8h. As long as a '1' remains in that position, updating is halted. After a halt is issued, the registers reflect the count; that is, the day, date, and the time that were current at the moment the halt command was issued. All of the TIMEKEEPER registers are updated simultaneously. A halt will not interrupt an update in progress. Updating is within a second after the bit is reset to a '0.' 6.2 Setting the clock Bit D7 of the control register (1FF8h) is the WRITE bit. Setting the WRITE bit to a '1,' like the READ bit, halts updates to the TIMEKEEPER(R) registers. The user can then load them with the correct day, date, and time data in 24-hour BCD format (see Table 5). Resetting the WRITE bit to a '0' then transfers the values of all time registers (1FF9h-1FFFh) to the actual TIMEKEEPER counters and allows normal operation to resume. The bits marked as '0' in Table 5 on page 16 must be written to '0' to allow for normal TIMEKEEPER and RAM operation. After the WRITE bit is reset, the next clock update will occur within one second. See the application note AN923 "TIMEKEEPER Rolling Into the 21st Century" for information on century rollover. 6.3 Stopping and starting the oscillator The oscillator may be stopped at any time. If the device is going to spend a significant amount of time on the shelf, the oscillator can be turned off to minimize current drain on the battery. The STOP bit is the MSB of the seconds register. Setting it to a '1' stops the oscillator. The M48T58/Y is shipped from STMicroelectronics with the STOP bit set to a '1.' When reset to a '0,' the M48T58/Y oscillator starts within 1 second. Doc ID 2412 Rev 8 15/33 Clock operations Table 5. M48T58, M48T58Y Register map Data Function/range Address D7 D6 1FFEh 0 0 1FFDh BLE BL 1FFCh 0 FT 1FFBh 0 0 1FFAh 0 1FF9h ST 1FF8h W 1FFFh D5 D4 D3 D2 10 Years D1 D0 BCD format Year Year 00-99 Month Month 01-12 Date Date 01-31 Century/day 0-1/1-7 Hours Hours 00-23 10 minutes Minutes Minutes 00-59 10 seconds Seconds Seconds 00-59 0 10 M 10 date CEB CB 0 Day 10 hours R S Calibration Control Keys: S = SIGN bit FT = FREQUENCY TEST bit R = READ bit W = WRITE bit ST = STOP bit 0 = Must be set to '0' BLE = Battery low enable bit BL = Battery low bit (read only) CEB = Century enable bit CB = Century bit Note: When CEB is set to '1,' CB will toggle from '0' to '1' or from '1' to '0' at the turn of the century (dependent upon the initial value set). When CEB is set to '0,' CB will not toggle. The WRITE bit does not need to be set to write to CEB. 6.4 Calibrating the clock The M48T58/Y is driven by a quartz-controlled oscillator with a nominal frequency of 32,768 Hz. The devices are tested not to exceed 35 ppm (parts per million) oscillator frequency error at 25C, which equates to about 1.53 minutes per month. With the calibration bits properly set, the accuracy of each M48T58/Y improves to better than +1/-2 ppm at 25C. The oscillation rate of any crystal changes with temperature (see Figure 8 on page 18). Most clock chips compensate for crystal frequency and temperature shift error with cumbersome "trim" capacitors. The M48T58/Y design, however, employs periodic counter correction. The calibration circuit adds or subtracts counts from the oscillator divider circuit at the divide by 256 stage, as shown in Figure 9 on page 18. The number of times pulses are blanked (subtracted, negative calibration) or split (added, positive calibration) depends upon the value loaded into the five calibration bits found in the control register. Adding counts speeds the clock up, subtracting counts slows the clock down. The calibration byte occupies the five lower order bits (D4-D0) in the control register 1FF8h. These bits can be set to represent any value between 0 and 31 in binary form. Bit D5 is the 16/33 Doc ID 2412 Rev 8 M48T58, M48T58Y Clock operations sign bit; '1' indicates positive calibration, '0' indicates negative calibration. Calibration occurs within a 64 minute cycle. The first 62 minutes in the cycle may, once per minute, have one second either shortened by 128 or lengthened by 256 oscillator cycles. If a binary '1' is loaded into the register, only the first 2 minutes in the 64 minute cycle will be modified; if a binary 6 is loaded, the first 12 will be affected, and so on. Therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator cycles for every 125,829,120 actual oscillator cycles, that is +4.068 or -2.034 ppm of adjustment per calibration step in the calibration register. Assuming that the oscillator is in fact running at exactly 32,768 Hz, each of the 31 increments in the calibration byte would represent +10.7 or -5.35 seconds per month which corresponds to a total range of +5.5 or - 2.75 minutes per month. Two methods are available for ascertaining how much calibration a given M48T58/Y may require. The first involves simply setting the clock, letting it run for a month and comparing it to a known accurate reference (like WWV broadcasts). While that may seem crude, it allows the designer to give the end user the ability to calibrate his clock as his environment may require, even after the final product is packaged in a non-user serviceable enclosure. All the designer has to do is provide a simple utility that accesses the calibration byte. The second approach is better suited to a manufacturing environment, and involves the use of some test equipment. When the frequency test (FT) bit (D6 in the day register) is set to a '1,' and D7 of the seconds register is a '0' (oscillator running), The frequency test (pin 1) will toggle at 512 Hz. Any deviation from 512 Hz indicates the degree and direction of oscillator frequency shift at the test temperature. For example, a reading of 512.01024 Hz would indicate a +20 ppm oscillator frequency error, requiring a -10 (WR001010) to be loaded into the calibration byte for correction. The frequency test pin is an open drain output which requires a pull-up resistor for proper operation. A 500-10 k resistor is recommended in order to control the rise time. For more information on calibration, see application note AN934, "TIMEKEEPER(R) calibration." Doc ID 2412 Rev 8 17/33 Clock operations Figure 8. M48T58, M48T58Y Crystal accuracy across temperature ppm 20 0 -20 -40 F = -0.038 ppm (T - T )2 10% 0 F C2 -60 T0 = 25 C -80 -100 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 C AI02124 Figure 9. Clock calibration NORMAL POSITIVE CALIBRATION NEGATIVE CALIBRATION AI00594B 18/33 Doc ID 2412 Rev 8 M48T58, M48T58Y 6.5 Clock operations Battery low flag The M48T58/Y automatically performs periodic battery voltage monitoring upon power-up. The battery low flag (BL), bit D6 of the flags register 1FFDh, will be asserted high if the internal or SNAPHAT(R) battery is found to be less than approximately 2.5 V and the battery low enable (BLE) bit has been previously set to '1.' The BL flag will remain active until completion of battery replacement and subsequent battery low monitoring tests. If a battery low is generated during a power-up sequence, this indicates that the battery voltage is below 2.5 V (approximately), which may be insufficient to maintain data integrity. Data should be considered suspect and verified as correct. A fresh battery should be installed. The SNAPHAT top may be replaced while VCC is applied to the device. Note: This will cause the clock to lose time during the interval the SNAPHAT(R) battery/crystal top is disconnected. Note: Battery monitoring is a useful technique only when performed periodically. The M48T58/Y only monitors the battery when a nominal VCC is applied to the device. Thus applications which require extensive durations in the battery back-up mode should be powered-up periodically (at least once every few months) in order for this technique to be beneficial. Additionally, if a battery low is indicated, data integrity should be verified upon power-up via a checksum or other technique. 6.6 Century bit Bit D5 and D4 of clock register 1FFCh contain the CENTURY ENABLE bit (CEB) and the CENTURY bit (CB). Setting CEB to a '1' will cause CB to toggle, either from a '0' to '1' or from '1' to '0' at the turn of the century (depending upon its initial state). If CEB is set to a '0,' CB will not toggle. Note: The WRITE bit must be set in order to write to the CENTURY bit. Doc ID 2412 Rev 8 19/33 Clock operations 6.7 M48T58, M48T58Y VCC noise and negative going transients ICC transients, including those produced by output switching, can produce voltage fluctuations, resulting in spikes on the VCC bus. These transients can be reduced if capacitors are used to store energy which stabilizes the VCC bus. The energy stored in the bypass capacitors will be released as low going spikes are generated or energy will be absorbed when overshoots occur. A bypass capacitor value of 0.1 F (as shown in Figure 10) is recommended in order to provide the needed filtering. In addition to transients that are caused by normal SRAM operation, power cycling can generate negative voltage spikes on VCC that drive it to values below VSS by as much as one volt. These negative spikes can cause data corruption in the SRAM while in battery backup mode. To protect from these voltage spikes, it is recommended to connect a Schottky diode from VCC to VSS (cathode connected to VCC, anode to VSS). Schottky diode 1N5817 is recommended for through hole and MBRS120T3 is recommended for surface mount. Figure 10. Supply voltage protection VCC VCC 0.1F DEVICE VSS AI02169 20/33 Doc ID 2412 Rev 8 M48T58, M48T58Y 7 Maximum ratings Maximum ratings Stressing the device above the rating listed in the absolute maximum ratings table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 6. Absolute maximum ratings Symbol TA TSTG Parameter Ambient operating temperature Storage temperature (VCC off, oscillator off) TSLD(1)(2)(3) Lead solder temperature for 10 seconds Value Unit 0 to 70 C -40 to 85 C 260 C VIO Input or output voltages -0.3 to 7 V VCC Supply voltage -0.3 to 7 V IO Output current 20 mA PD Power dissipation 1 W 1. For DIP package, soldering temperature of the IC leads is to not exceed 260 C for 10 seconds. Furthermore, the devices shall not be exposed to IR reflow nor preheat cycles (as performed as part of wave soldering). ST recommends the devices be hand-soldered or placed in sockets to avoid heat damage to the batteries. 2. For DIP packaged devices, ultrasonic vibrations should not be used for post-solder cleaning to avoid damaging the crystal. 3. For SOH28 package, lead-free (Pb-free) lead finish: reflow at peak temperature of 260C (the time above 255C must not exceed 30 seconds). Caution: Negative undershoots below -0.3 V are not allowed on any pin while in the battery backup mode. Caution: Do NOT wave solder SOIC to avoid damaging SNAPHAT(R) sockets. Doc ID 2412 Rev 8 21/33 DC and AC parameters 8 M48T58, M48T58Y DC and AC parameters This section summarizes the operating and measurement conditions, as well as the DC and AC characteristics of the device. The parameters in the following DC and AC characteristic tables are derived from tests performed under the measurement conditions listed in Table 7. Designers should check that the operating conditions in their projects match the measurement conditions when using the quoted parameters. Table 7. Operating and AC measurement conditions Parameter Supply voltage (VCC) M48T58 M48T58Y Unit 4.75 to 5.5 4.5 to 5.5 V 0 to 70 0 to 70 C Load capacitance (CL) Ambient operating temperature (TA) 100 100 pF Input rise and fall times 5 5 ns 0 to 3 0 to 3 V 1.5 1.5 V Input pulse voltages Input and output timing ref. voltages Note: Output Hi-Z is defined as the point where data is no longer driven. Figure 11. AC measurement load circuit 5V 1.9k DEVICE UNDER TEST OUT 1k CL = 100pF or 5pF CL includes JIG capacitance Table 8. AI01030 Capacitance Symbol Parameter(1)(2) Min Max Unit CIN Input capacitance - 10 pF Output capacitance - 10 pF COUT (3) 1. Effective capacitance measured with power supply at 5 V; sampled only, not 100% tested. 2. At 25 C, f = 1 MHz. 3. Outputs deselected. 22/33 Doc ID 2412 Rev 8 M48T58, M48T58Y Table 9. DC and AC parameters DC characteristics Symbol M48T58 Test condition(1) Parameter Unit Min Input leakage current ILI ILO(2) Output leakage current M48T58Y Max Min Max 0 V VIN VCC 1 1 A 0 V VOUT VCC 1 1 A Outputs open 50 50 mA E1 = VIH E2 = VIO 3 3 mA E1 = VCC - 0.2 V E2 = VSS + 0.2 V 3 3 mA ICC Supply current ICC1 Supply current (standby) TTL ICC2 Supply current (standby) CMOS VIL Input low voltage -0.3 0.8 -0.3 0.8 V VIH Input high voltage 2.2 VCC + 0.3 2.2 VCC + 0.3 V VOL VOH Output low voltage IOL = 2.1 mA 0.4 0.4 Output low voltage (FT) IOL = 10 mA 0.4 0.4 Output high voltage IOH = -1 mA (3) 2.4 V 2.4 V 1. Valid for ambient operating temperature: TA = 0 to 70 C; VCC = 4.75 to 5.5 V or 4.5 to 5.5 V (except where noted). 2. Outputs deselected. 3. The FT pin is open drain. Figure 12. Power down/up mode AC waveforms VCC VPFD (max) VPFD (min) VSO tF tR tFB tDR tPD INPUTS tRB RECOGNIZED trec DON'T CARE RECOGNIZED HIGH-Z OUTPUTS VALID VALID (PER CONTROL INPUT) (PER CONTROL INPUT) AI01168C Doc ID 2412 Rev 8 23/33 DC and AC parameters Table 10. M48T58, M48T58Y Power down/up AC characteristics Parameter(1) Symbol Min tPD E1 or W at VIH or E2 at VIL before power down tF(2) VPFD (max) to VPFD (min) VCC fall time tFB(3) VPFD (min) to VSS VCC fall time Max 0 Unit s 300 s M48T58 10 s M48T58Y 10 s tR VPFD (min) to VPFD (max) VCC rise time 10 s tRB VSS to VPFD (min) VCC rise time 1 s trec VPFD (max) to inputs recognized 40 200 ms 1. Valid for ambient operating temperature: TA = 0 to 70 C; VCC = 4.75 to 5.5 V or 4.5 to 5.5 V (except where noted). 2. VPFD (max) to VPFD (min) fall time of less than tF may result in deselection/write protection not occurring until 200 s after VCC passes VPFD (min). 3. VPFD (min) to VSS fall time of less than tFB may cause corruption of RAM data. Table 11. Power down/up trip points DC characteristics Parameter(1)(2) Symbol VPFD Power-fail deselect voltage VSO Battery backup switchover voltage tDR(3) Expected data retention time Min Typ Max Unit M48T58 4.5 4.6 4.75 V M48T58Y 4.2 4.35 4.5 V 3.0 7 V Years 1. Valid for ambient operating temperature: TA = 0 to 70 C; VCC = 4.75 to 5.5 V or 4.5 to 5.5 V (except where noted). 2. All voltages referenced to VSS. 3. At 25 C, VCC = 0 V. 24/33 Doc ID 2412 Rev 8 M48T58, M48T58Y 9 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Figure 13. PCDIP28 - 28-pin plastic DIP, battery CAPHATTM, package outline A2 A1 B1 B A L C e1 eA e3 D N E 1 PCDIP Note: Drawing is not to scale. Table 12. PCDIP28 - 28-pin plastic DIP, battery CAPHATTM, package mech. data mm inches Symb Typ Min Max A 8.89 A1 Typ Min Max 9.65 0.350 0.380 0.38 0.76 0.015 0.030 A2 8.38 8.89 0.330 0.350 B 0.38 0.53 0.015 0.021 B1 1.14 1.78 0.045 0.070 C 0.20 0.31 0.008 0.012 D 39.37 39.88 1.550 1.570 E 17.83 18.34 0.702 0.722 e1 2.29 2.79 0.090 0.110 e3 33.02 1.3 eA 15.24 16.00 0.600 0.630 L 3.05 3.81 0.120 0.150 N 28 Doc ID 2412 Rev 8 28 25/33 Package mechanical data M48T58, M48T58Y Figure 14. SOH28 - 28-lead plastic small outline, 4-socket battery SNAPHAT(R), package outline A2 A C B eB e CP D N E H A1 a L 1 Note: SOH-A Drawing is not to scale. Table 13. SOH28 - 28-lead plastic small outline, 4-socket battery SNAPHAT(R), package mech. data mm inches Symb Typ Min A Typ Min 3.05 Max 0.120 A1 0.05 0.36 0.002 0.014 A2 2.34 2.69 0.092 0.106 B 0.36 0.51 0.014 0.020 C 0.15 0.32 0.006 0.012 D 17.71 18.49 0.697 0.728 E 8.23 8.89 0.324 0.350 - - - - eB 3.20 3.61 0.126 0.142 H 11.51 12.70 0.453 0.500 L 0.41 1.27 0.016 0.050 a 0 8 0 8 N 28 e CP 26/33 Max 1.27 0.050 28 0.10 Doc ID 2412 Rev 8 0.004 M48T58, M48T58Y Package mechanical data Figure 15. SH - 4-pin SNAPHAT(R) housing for 48 mAh battery & crystal, pack. outline A1 A2 A eA A3 B L eB D E SHTK-A Note: Drawing is not to scale. Table 14. SH - 4-pin SNAPHAT(R) housing for 48 mAh battery & crystal, package mech. data mm inches Symb Typ Min A Max Typ Min 9.78 Max 0.385 A1 6.73 7.24 0.265 0.285 A2 6.48 6.99 0.255 0.275 A3 0.38 0.015 B 0.46 0.56 0.018 0.022 D 21.21 21.84 0.835 0.860 E 14.22 14.99 0.560 0.590 eA 15.55 15.95 0.612 0.628 eB 3.20 3.61 0.126 0.142 L 2.03 2.29 0.080 0.090 Doc ID 2412 Rev 8 27/33 Package mechanical data M48T58, M48T58Y Figure 16. SH - 4-pin SNAPHAT(R) housing for 120 mAh battery & crystal, package outline A1 A2 A eA A3 B L eB D E SHTK-A Note: Drawing is not to scale. Table 15. SH - 4-pin SNAPHAT(R) housing for 120 mAh battery & crystal, package mech. data mm inches Symb Typ Min A Typ Min 10.54 Max 0.415 A1 8.00 8.51 0.315 0.335 A2 7.24 8.00 0.285 0.315 A3 28/33 Max 0.38 0.015 B 0.46 0.56 0.018 0.022 D 21.21 21.84 0.835 0.860 E 17.27 18.03 0.680 0.710 eB 3.20 3.61 0.126 0.142 L 2.03 2.29 0.080 0.090 Doc ID 2412 Rev 8 M48T58, M48T58Y 10 Part numbering Part numbering Table 16. Ordering information scheme Example: M48T 58 -70 MH 1 E Device type M48T Supply voltage and write protect voltage 58(1) = VCC = 4.75 to 5.5 V; VPFD = 4.5 to 4.75 V 58Y = VCC = 4.5 to 5.5 V; VPFD = 4.2 to 4.5 V Speed -70 = 70 ns Package PC = PCDIP28 MH(2) = SOH28 Temperature range 1 = 0 to 70C Shipping method For SOH28: blank = Tubes (not for new design - use E) E = Lead-free package (ECOPACK(R)), tubes F = Lead-free package (ECOPACK(R)), tape & reel TR = Tape & reel (not for new design - use F) For PCDIP28: blank = Tubes 1. The M48T58 part is offered with the PCDIP28 (e.g., CAPHATTM) package only. 2. The SOIC package (SOH28) requires the SNAPHAT(R) battery package which is ordered separately under the part number "M4TXX-BR12SH" in plastic tube or "M4TXX-BR12SHTR" in Tape & Reel form (see Table 17). Caution: Do not place the SNAPHAT(R) battery package "M4TXX-BR12SH" in conductive foam as it will drain the lithium button-cell battery. For other options, or for more information on any aspect of this device, please contact the ST sales office nearest you. Doc ID 2412 Rev 8 29/33 Part numbering M48T58, M48T58Y Table 17. SNAPHAT(R) battery table Part number M4T28-BR12SH M4T32-BR12SH 30/33 Description Package Lithium battery (48 mAh) SNAPHAT(R) SH Lithium battery (120 mAh) SNAPHAT(R) SH Doc ID 2412 Rev 8 M48T58, M48T58Y 11 Environmental information Environmental information Figure 17. Recycling symbols This product contains a non-rechargeable lithium (lithium carbon monofluoride chemistry) button cell battery fully encapsulated in the final product. Recycle or dispose of batteries in accordance with the battery manufacturer's instructions and local/national disposal and recycling regulations. Doc ID 2412 Rev 8 31/33 Revision history 12 M48T58, M48T58Y Revision history Table 18. 32/33 Document revision history Date Revision Changes Jul-1999 1 27-Jul-2000 1.1 04-Jun-2001 2 31-Jul-2001 2.1 Formatting changes from recent document review findings 20-May-2002 2.2 Modify reflow time and temperature footnotes (Table 6) 01-Apr-2003 3 v2.2 template applied; test condition updated (Table 11) 17-Jul-2003 3.1 02-Apr-2004 4 Reformatted; update lead-free packaging information (Table 6, 16) 30-Aug-2007 5 Reformatted; added lead-free second level interconnect information to cover page and Section 9: Package mechanical data; updated Table 9. 24-Mar-2009 6 UpdatedTable 6, Section 9: Package mechanical data; added Section 11: Environmental information; minor reformatting. 02-Aug-2010 7 Reformatted document; updated Section 7, Table 12. 07-Jun-2011 8 Updated footnote 1 of Table 6: Absolute maximum ratings; updated Section 11: Environmental information. First issue Century bit and battery low flag paragraphs added; power down/up AC characteristics table and waveforms changed (Table 10, Figure 12) Reformatted; temperature information added (Table 9, 3, 4, 10, 11) Update "battery low flag" information Doc ID 2412 Rev 8 M48T58, M48T58Y Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2011 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 2412 Rev 8 33/33