TD62930P/F
2001-07-05
1
TOSHIBA BIPOLAR DIGITAL IC SILICON MONOLITHIC
TD62930P,TD62930F
THREE−CHANNEL SMALL−SIGNAL IGBT GATE DRIVER
The TD62930P and TD62930F are drivers using 5 V−signal input
to output the signals required to drive IGBT gates.
TD62930P / F is the most suitable for low−side drive of a
miniature IGBT to use for inverter for the household electric
appliances mainly.
The outputs are separated into high−side and low−side outputs.
This separation simplifies the IGBT gate on / off timing control.
Two output signals are assigned for one input signal.
The high−side output is high−level for high−level input, and high
impedance for low−level input. The low−side output is high
impedance for high−level input, and low−level for low−level
input.
FEATURES
Power supply voltage (maximum rating)
High−voltage block power supply voltage VCC = 30 V
Low−voltage block power supply voltage VDD = 7 V
Output current (maximum rating)
High−side peak current IOUT = −0.4 A (max)
Low−side peak current IOUT = 0.4 A (max)
Input−output response speed tpHL, tpLH ≤ 1 µs (max)
Package : DIP16 / SSOP16 (1.00 mm pitch)
Weight
DIP16−P−300−2.54A : 1.11 g (Typ.)
SSOP16−P−225−1.00A : 0.14 g (Typ.)
TD62930P/F
2001-07-05
2
PIN ASSIGNMENT (TOP VIEW)
INTERNAL EQUIVALENT CIRCUIT
PIN DESCRIPTION
PIN No. PIN NAME FUNCTION
1, 8 VCC 30 V supply pins
2 VDD 5 V supply pin
3, 7 L−GND Ground pins for 5 V supply
4, 5, 6 IN1~3 Input pins for 5 V output control signals
11, 14 P−GND Ground pins for 30 V supply
9, 12, 15 OUT−L1~3 Low−side output pins
10, 13, 16 OUT−H1~3 High−side output pins
TD62930P/F
2001-07-05
3
MAXIMUM RATINGS (Ta = 25°C)
CHARACTERISTIC PIN / PACKAGE SYMBOL RATING UNIT
Power Supply Voltage VCC VCC 30 V
Power Supply Voltage VDD VDD 7 V
Input Voltage IN1~3 VIN −0.5~VDD + 0.5 V
0~20 (Ta = −20~85°C)
OUT−H1~3 VOUT (H) 0~30 (Ta = −20~70°C)
V
−0.5~20 (Ta = −20~85°C)
Output Voltage
OUT−L1~3 VOUT (L) −0.5~30 (Ta = −20~70°C)
V
High−level Output Peak Current OUT−H1~3 IOPH (Note 1) −0.4 A / ch
Low−level Output Peak Current OUT−L1~3 IOPL (Note 1) +0.4 A / ch
Operating Frequency IN1~3 f 25 kHz
DIP16 PD1 (Note 2) 1.47 (FREE AIR) W
Power Dissipation
SSOP16 PD2 (Note 2) 0.78 (ON PCB) W
Operating Ambient Temperature Topr −20~85 °C
Storage Temperature Tstg −55~150 °C
Note 1: Output pin current
The pulse width of the output pin current at peak is ≤ 1 µs, 300 pps.
Note 2: When ambient temperature exceeds 25°C
Derate the power dissipation of DIP−type devices at 11.76 mW / 1°C (device only) and
Derate the power dissipation of SMD−type devices at 6.24 mW / 1°C (mounted on the board).
RECOMMENDED OPERATING CONDITIONS
(Unless otherwise specified, Ta = −20 to 70°C)
CHARACTERISTIC PIN SYMBOL TEST CONDITION MIN TYP. MAX UNIT
High level VIH 3.5 ― ―
Input Voltage
Low level
IN1~3
VIL
VCC = 15 V,
VDD = 4.5~5.5 V ― ― 1.0
V
High level IIH ― ― 5
Input Current
Low level
IN1~3
IIL
VCC = 15 V,
VDD = 4.5~5.5 V ― ― −5
mA
VCC VCC 10 15 25
Input Power Supply Voltage
VDD VDD 4.5 5.0 5.5
V
IOH (DC) ― ― −0.1
OUT−H1~3
IOH (Peak)
VCC = 20 V, VDD = 4.5 V
― ― −0.35
IOL (DC) ― ― 0.1
Output Current
OUT−L1~3
IOL (Peak)
VCC = 20 V, VDD = 4.5 V
― ― 0.35
A
VCC = 30 V, VDD = 5.5 V −20 25 70
Operating Temperature Topr VCC = 20 V, VDD = 5.5 V −20 25 85
°C
TD62930P/F
2001-07-05
4
ELECTRICAL CHARACTERISTICS (Unless otherwise specified, Ta = −20 to 70°C)
CHARACTERISTIC PIN SYMBOL TEST CONDITION MIN TYP. MAX UNIT
High level IIH VCC = 15 V, VIN = 5 V 0.1 0.2 0.4
Input Current
Low level
IN1~3
IIL VCC = 15 V, VIN = 0 V ― 0 ―
mA
High level OUT−H1~3 VOH VCC = 15 V, VIH = 5 V,
RLH = 100 Ω
VCC
−4.0
VCC
−1.9
VCC
−1.0
Output
Voltage
Low level OUT−L1~3 VOL VCC = 15 V, VIL = 0 V,
RLL = 100 Ω 0.3 0.5 2.5
V
VDD = 5.5 V, VIH = 0 V,
Ta = 25°C ― 1.5 3.0
IDDL VDD = 5.5 V, VIH = 0 V,
Ta = −20~85°C ― ― 3.5
VDD = 5.5 V, VIH = 5 V,
Ta = 25°C ― 1.8 3.5
Dissipation Current 1 VDD
IDDH VDD = 5.5 V, VIH = 5 V,
Ta = −20~85°C ― ― 4.0
mA
VCC = 30 V, VDD = 5.5 V,
V
IH = 0 V, Ta = 25°C ― 10.2 15.0
ICCL
VCC = 30 V, VDD = 5.5 V,
VIH = 0 V ― ― 18.0
VCC = 30 V, VDD = 5.5 V,
V
IH = 5 V, Ta = 25°C ― 7.5 11.0
Dissipation Current 2 VCC
ICCH
VCC = 30 V, VDD = 5.5 V,
VIH = 5 V ― ― 14.0
mA
Operating Power Supply Voltage VCC VCCopr 10 ― 30 V
SWITCHING CHARACTERISTICS (Unless otherwise specified, Ta = −20~70°C)
CHARACTERISTIC PIN SYMBOL TEST CONDITION MIN TYP. MAX UNIT
High level OUT−H1~3 tPLH
VDD = 5.0 V, VCC = 15 V
RLH = RLL = 100 Ω,
VIN = 0.7 to 4 V
― 0.25 1.00
Output
Propagation
Delay Time
Low level OUT−L1~3 tPHL
VDD = 5.0 V, VCC = 15 V
RLH = RLL = 100 Ω,
VIN = 4 to 0.7 V
― 0.25 1.00
µs
TD62930P/F
2001-07-05
5
SWITCHING WAVEFORM
PROPAGATION DELAY TIME TEST CIRCUIT
Toshiba recommends connecting load resistors as in the above diagram, utilizing the independence of the
high−level and low−level sides of this IC.
TD62930P/F
2001-07-05
6
TEST CIRCUIT
(1) IIH (2) IIL
(3) VIH, VOH (4) VIL, VOL
(5) IDDL, IDDH (6) ICCL, ICCH
TD62930P/F
2001-07-05
7
APPLICATION CIRCUIT
PRECAUTIONS for USING
This IC does not integrate protection circuits such as overcurrent and overvoltage protectors.
Thus, if excess current or voltage is applied to the IC, the IC may be damaged. Please design the IC so that
excess current or voltage will not be applied to the IC.
Utmost care is necessary in the design of the output line, VCC and GND (L−GND, P−GND) line since IC may be
destroyed due to short−circuit between outputs, air contamination fault, or fault by improper grounding.
TD62930P/F
2001-07-05
8
PACKAGE DIMENSIONS
DIP16−P−300−2.54A Unit: mm
Weight: 1.11 g (Typ.)
TD62930P/F
2001-07-05
9
PACKAGE DIMENSIONS
SSOP16−P−225−1.00A Unit: mm
Weight: 0.14 g (Typ.)
TD62930P/F
2001-07-05
10
• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc..
• The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this
document shall be made at the customer’s own risk.
• The products described in this document are subject to the foreign exchange and foreign trade laws.
• The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other
rights of the third parties which may result from its use. No license is granted by implication or otherwise under
any intellectual property or other rights of TOSHIBA CORPORATION or others.
• The information contained herein is subject to change without notice.
000707EB
A
RESTRICTIONS ON PRODUCT USE
