DATA Slr 74LV4052 =| Dual 4-channel analog multiplexer/demultiplexer Product specification Supersedes data of 1997 Jul 15 IC24 Data Handbook Philips Semiconductors 1998 Jun 23 PHILIPSPhilips Semiconductors Product specification Dual 4-channel analog multiplexer/demultiplexer 74LV4052 FEATURES Optimized for low voltage applications: 1.0 to 6.0 V Accepts TTL input levels between Voc = 2.7 V and Vcc = 3.6 V Low typ ON? resistance: 60 Q at Veg ~ Veg = 4.5 V 90 Q at Veg - Veg = 3.0 V 145 Q at Veg Veg = 2.0V Logic level translation: to enable 3 V logic to communicate with + 3 V analog signals Typical break before make built in Analog/Digital multiplexing and demultiplexing Signal gating Output capability: non-standard ioc category: MSI DESCRIPTION The 74LV4052 is a low-voltage CMOS device.and is pin and function compatible with the 74HC/HCT4052. The 74LV4052 is a dual 4-channel analog multiplexer/demultiplexer with a common select logic. Each multiplexer has four independent inputs/outputs (ng to NY) and a common input/output (nZ). The common channel select logics include two digital select inputs (Spo and S;) and an active LOW enable input (E). With E LOW, one of.the four switches is selected {low impedance ON-state) by Sp and S;_ With E HIGH, all switches are in the high impedance OFF-state, independent of Sp and S1. Voc and GND are the supply voltage pins for the digital control inputs (So, S; and E). The Vec to GND ranges are 1.0 to 6.0 V. The analog inputs/outputs {no, to nY3, and nZ) can swing between Vcc as a positive limit and Vee as a negative limit. Voc - Veg may not exceed 6.0 V. For operation as a digital multiplexer/demultiplexer, Vee is connected to GND (typically ground). QUICK REFERENCE DATA GND = 0 V; Tamp = 25C; t, =tp 5 2.5 ns SYMBOL PARAMETER CONDITIONS TYPICAL UNIT Turn ON time Cy = 15 pF tezttezi E or Vog Sn RL = 1KQ 30 ns tought Turn OFF time Voc =3.3-V 39 PHZUPLZ E or Vos Sn Cy Input capacitance 3.5 Cpep Power dissipation capacitance per switch | See Notes 1 and 2 57 oF C Maximum switch capacitance 5 Ss independent (Y) common (Z) 12 NOTES: 1. Cpp is used to determine the dynamic power dissipation (Pp in pW) Pp = Cpp x Veo? xf + = ((Cy 4. Cg) x Voc? x fg) where: f, = input frequency in MHz; C, = output load capacity in pF; fy) = output frequency in MHz; Gs = maximum switch capacitance in pF; Voc = supply voltage in V; = ((C, +Gs) x Vec x fg} = sum of the outputs. 2. The condition is V;= GND to Vcc. ORDERING INFORMATION PACKAGES TEMPERATURE RANGE | OUTSIDE NORTH AMERICA | NORTH AMERICA Code 16-Pin Plastic DIL 40C to +125C 741.4052 N 74LV4052 N SOT38-4 16-Pin Plastic SO ~40C to +425C 741V4052 D 74LV4052 D SOT 109-4 16-Pin Plastic SSOP Type Il ~40C to +125C 74LV4052 DB 74LV4052 DB SOT338-1 16-Pin Plastic TSSOP Type | 40C to +126C 74LV4052 PW 74LV4052PW DH 80T403-1 PIN CONFIGURATION PIN DESCRIPTION PIN NUMBER | SYMBOL FUNCTION 2q [7] VY i) Veo oy I Hg] 3 4,5,2,4 2Y 9, 2Y3 Independent inputs/outputs 2 2 ' oz Fa] 1, 6 E Enable input (active LOW) aya [i Fa} 12 7 Vee Negative supply voltage 2v, [5 a] 1Y0 8 GND Ground (OV) Ef] Fa} 1Y, 10,9 So, $4 Select inputs 12, 14,15, 11 | 1Y9to 13 _ | Independent inputs/outputs VEE {Z| [16] So GND a ra} 13,3 1Z, 2Z Common inputs/outputs Pi olta: Svor89? 16 Voc ositive supply voltage 1998 Jun 23 853-1999 19618Philips Semiconductors Dual 4-channel analog multiplexer/demultiplexer LOGIC SYMBOL (IEEEAEC) 10 9 6 13 an SVO1E99 LOGIC SYMBOL 13 12 1 g /~ 12 10 1Sy 9 1 ro 14 915, 1 9 Fe 15 1 3h nN 2 9 1 2,h--5 2 }- 2 2g+- 4 B-OE , svoregs FUNCTION TABLE INPUTS CHANNEL E S Sp ON L L L AYg NZ L L H n,nZ L Hi L nonZ L H H n3 nzZ H Xx x None NOTES: 1. H = HIGH voltage level 2. L = LOW voltage ijevel 3. X = don't care 1998 Jun 23 Product specification 74LV4052Philips Semiconductors Product specification Dual 4-channel analog multiplexer/demultiplexer 74LV4052 FUNCTIONAL DIAGRAM 1Z 13 iv 12 t ~ x 14 : z 15 | ~~ < is] 4 Locic LeveL |__| t-of-4 CONVERSION DECODER n < t NM << iP } nN < } = 2Y3 4 az 3 Ly, GND EE 8 7 Svo1700 SCHEMATIC DIAGRAM (ONE SWITCH) JG Joly i Voc |_| Vo om Veg VEE trom sogic 4 VEE 2 Sv01695 1998 Jun 23 4Philips Semiconductors Product specification Dual 4-channel analog multiplexer/demultiplexer 74LV4052 ABSOLUTE MAXIMUM RATINGS! 2 In-accordance with the Absolute Maximum Rating System (IEC 134). Voltages are referenced to GND (ground = 0 V). SYMBOL PARAMETER CONDITIONS RATING UNIT Vec DC supply voltage -O0.5 to +7.0 Vv th DC input diode current Vi <-O0.5 or Vi > Veo + 0.5-V 20 mA tigx DC switch diode current Vs <-0.5 07 Vg > Veco + 0.5 V 20 mA 15 DC switch current ~O.5V<Vs< Veco + 05V 25 mA Tstg Storage temperature range ~65 to +150 C Power dissipation per package for temperature range: -40 to +125C Pp ~ plastic DIL above +70C derate linearly with. 12 mW/K 750 mW TOT ~ plastic mini-pack (SO) above +70C derate linearly with 8 mW/K 500 plastic shrink mini-pack (SSOP and TSSOP) | above +60C derate linearly with 5.5 mW/K 400 NOTES: 1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER CONDITIONS MIN TyP MAX UNIT Vec DC supply voltage See Note 1 and Figure 5 1.0 3.3 6.0 Vv Vy Input vohage 0 - Veco Vv Vo Output voltage 9 ~ Vec Vv : . . : See DC and AC 40 +85 Tamb Operating ambient temperature range in free air characteristics 40 #125 Cc Vee = 1.0 Vto2.0V ~ - 500 ty, te Input rise and fall times Veco =2.0Vto2.7V - ~ 200 ns/V Veo =2.7 Vte6.0V - - 100 NOTE: 1. The LV is guaranteed to function down to Vcc = 1.0V (input levels GND or Voc); DC characteristics are guaranteed from Voc = 1.2V to Voc = 6.0V. 1998 Jun 23Philips Semiconductors Product specification Dual 4-channel analog multiplexer/demultiplexer 74LV4052 DC ELECTRICAL CHARACTERISTICS Over recommended operating conditions, voltages are referenced to GND (ground = 0 V) LIMITS SYMBOL PARAMETER TEST CONDITIONS -40C to +85C -40C to +125C UNIT MIN Typ! MAX MIN MAX Voc =1.2V 0.9 0.9 G r Veo =2.0V 1.4 1.4 HIGH level Input Vin voltage Veo = 2.7 103.6 V 2.0 2.0 v Veo =4.5V 3.15 3.15 Veco = 6.0 V 4.20 4.20 Veg =1.2V 0.3 0.3 LOWI Veco = 2.0V 0.6 0.6 evel Input ViL voltage Vec = 2.7 to 3.6 V 0.8 0.8 Vv Voc =4.5V 1.35 1.35 Veco = 6.0V 1.80 1.80 Voc = 3.6 1.0 1.0 +h Input leakage cc Vi = Voc or GND uA current Voc = 6.0 2.0 2.0 Analog switch Vec = 3.6 Vi= Vin or Vie 1.0 1.0 ts OFF-state current IVsl = Veco - GND WA per channel Voc = 6.0 (See Figure 2) 2.0 2.0 Voc = 3.6 Vi = Vin or Vip 1.0 1.0 #s [ONistiecurent [ya Nel = Voc = GND us Voc = 6.0 (See Figure 3) 2.0 2.0 : Veo =3.6V Vi, = Veo or GND; 20.0 40 \ Quiescent supply ; A cc current Vis = GND or Voc; ty Veco =6.0V Vos = Voc or GND 40.0 80 Additional Alcc quiescent supply Voc =2.7t0o36V |Vi=Vec~0.6V 500 850 pA current per input Vi = Ving or Vics Voc =1.2V Ig = 100 , A; Vis = Voc to GND a ON-resistance [vec =2.0 145 325 375 ON (peak) Veo =2.7V Vy = Vin OF Vit: 90 200 235 Voc =3.0t03.6V [ls = 1000 ,A; 80 180 210 Veo =4.5V Vis = Vee to GND 60 135 160 Voc = 6.0V 55 125 145 Vi = Vin or Vit: Veo =12V Ig = 100 A: 225 Vig . GN = 2, 110 235 270 R ON-resistance Voc = 2.0 2 ON (rail) Veco =2.7V Vi = Vi or Vit: 70 145 165 Veo #3.0103.6V [ls = 1000 ,A; 60 130 150 Veo = 4.5V Vis = GND 45 100 115 co=4. Voc = 6.0 V 40 85 100 NOTES: 1. Alf typical values are measured at Tamp = 25C. 2. At supply voltages approaching 1.2 V, the analog switch ON-resistance becomes extremely non-linear. Therefore, itis recommended that these devices be used to trarismit digital signals only, when using these supply voltages. 3. Ron (MAX) data is preliminary. 1998 Jun 23Philips Semiconductors Product specification Dual 4-channel analog multiplexer/demultiplexer 74LV4052 DC ELECTRICAL CHARACTERISTICS (Continued) LIMITS SYMBOL PARAMETER TEST CONDITIONS 40C to +85C 40C to +125C UNIT MIN TYP? MAX MIN MAX Vy = Ving OF Viv; Vec=1.2V tg = 100 ,A; 250 Q Vis = Vec Row ON-resistance Veco = 2.0V 120 320 370 (rail) Veo = 2.7.V Vi = Vin or Vin: 7 195 225 Vec =3.0te3.6V Ig = 1000 A; 70 175 205 Q Veo=45V Vis = Vec 50 130 750 Voc = 6.0V 45 120 135 Veo =12V Maximum variation [Voc = 2-0 V 5 ARon of ON-resistance [| Voc = 2.7 V Vi = Vin or Vip: 4 Q between any two Veo =3.01t03.6V |Vis=Voc to GND 4 channels Voo=45V 3 Voc =6.0V 2 NOTES: 1. All typical values are measured at Tamp = 25C. 2. At supply voltages approaching 1.2 V, the analog switch ON-resistance becomes extremely non-linear. Therefore, it is recommended that these devices be used to transmit digital signals only, when using these supply voltages. 3. Ron (MAX) data is preliminary. (from select inputs) > Vis =OtoV > VEE oO HIGH AY, > Bgl EX SV01688 LOW (from select inputs} V. = Voc of Vee Vos Veg or Voc po | Vee S01660 Figure 1. Test circuit for measuring ON-resistance (Ron). Figure 2. Test circuit for measuring OFF-state current. (from select inputs) HIGH Vi = Voc Of Vege nYq L nz _ PS - (open circuit} SV01661 Figure 3. Test circuit for measuring ON-state current. 1998 Jun 23 Ron 150 (2) 120 90 0 1.2 24 3.6 48 Vv is ) Svor7e1 Figure 4. Typical ON-resistance (R,,,) as a function of input voitage (Vis) for Vig = 0 to Voc Veg-Philips Semiconductors Product specification Dual 4-channel analog multiplexer/demultiplexer 74LV4052 Voc - GND vy) 6.0 40 2.0 Qo 2.0 4.0 6.0 Veco - Ver Vv) SV01662 Figure 5. Guaranteed operating area as a function of the supply voltages. AC CHARACTERISTICS GND = 0 V; t, = < 2.5ns; C, = 50pF MIT. CONDITION s - SYMBOL PARAMETER A0 to +85 C 40 to +125 C | nit e OTHER MIN | TYP? | MAX | MIN | MAX [- 12 25 2.0 9 7 20 Propagation delay 27 _ 6 13 15 tet Cy = 50 pF PHU'PLH | Vis 0 Vos 3.01036 peep 52 10 12 ns Figure 12 45 4 9 10 6.0 3 7 8 12 190 2.0 Ry = 1kQ: 65 121 146 Turn-on time 2.7 C, = 50 pF 48 89 108 t t ns pawitpz. | , to Vos 3.0103.6 Figures 13 362 7i 86 45. and 1 32 60 73 6.0 25 46 56 72 125 2.0 Ry = 1kQ: 43 80 95 _ Tum-off time 27 C, = 50 pF 33 59 71 ns PHZPLZ E, Sn to Vos 3.010 3.6 Figures 13 264 48 57 45 and 1 23 a1 49 6.0 18 32 38 NOTES: 1. Unless otherwise stated, all typical values are measured at Tamp = 25C 2. Typical values are measured at Vcc = 3.3 V. 1998 Jun 23 8Philips Semiconductors Product specification Dual 4-channel analog multiplexer/demultiplexer 74LV4052 ADDITIONAL AC CHARACTERISTICS Recommended conditions and typical values GND = 0 V; t, = ty $ 2.5ns SYMBOL PARAMETER TYP. | UNIT | Voc | Vistp-p) CONDITIONS wo | Sine-wave distortion 0.80 % 3.0 2.75 | Ry. = 10kQ; Cy = 50 pf f= 1 kHz 0.40 6.0 5.50 | Figure 9 and 10 Sine-wave distortion 2.40 % 3.0 2.75 | Ry = 10 kQ; C, = 50 pf f = 10 kHz 1.20 6.0 5.50 | Figure 9 and 10 Switch OFF signal feed through ~50 dB 3.0 Note 1 | Ry = 600 &; C, = 50 pf; f= 1 MHz 50 8.0 Figures 5 and 14 Crosstalk between any two ~60 dB 3.0 | Note 1 | Ry = 600 2; C, = 50 pt; f= 1 MHz switches/multiplexers . -60 6.0 Figure 8 . Vip-p) Crosstalk voltage between enable or 110 mV 3.0 Ry = 600 2; CL = 50 pf: f= 1 MHz address input to any switch 120 6.0 (S, or E, square wave between Vcc (peak-to-peak value) and GND t, = ty = 6 ns) Figure 8 fmax Minimum frequency response 180 | MHz 3.0 | Note2 | Ry = 50 Q; C, = 50 pF (-3 dB) 200 6.0 Figures 6, 8 and 9 Cs Maximum switch capacitance 5 pf GENERAL NOTES: 1. Vig is the input voltage at nY or nZ terminal, whichever is assigned as an input. 2. Vos is the output voltage at nY or nZ terminal, whichever is assigned as an output. NOTES: 1. Adjust input voltage Vj, is 0 dBm level (0 dBm = 1 mW into 600 2). 2. Adjust input voltage Vj, is 0 dBm level at Vog for 1 MHz (0 dBm = 1 mW into 50 2). 5 (a8) (dB) Qa -50 - ~100 . 10 10? 103 10% 105 106 10 102 103 104 (kHz) 105 106 f (kHz) SVO1E3S SVOTESE Figure 6. Typical switch OFF signal feed-through as a Figure 7. Typical frequency response. function of frequency. NOTES TO FIGURES 6 AND 7: Test conditions: Vcc = 3.0 V; GND = 0 V; Veg = -3.0 V; Ry = 50 Q; Rgource = 1k2. Voc Vec aR, aR. nZiny , nY,/nZ nZziny,, bX me Cy RL channel aR, =e CO, arn (#) GND GND @) (b) SV01663 Figure 8. Test circuit for measuring crosstalk between any two switches. (a) channel ON condition; (b) channel OFF condition. 1998 Jun 23 9Philips Semiconductors Product specification Dual 4-channel analog multiplexer/demultiplexer 74LV4052 NOTE TO FIGURE B: The crosstalk is defined as follows (oscilloscope output): Vip - p) VT SVO1642 Voc Spor E Vec | aR, aR ny p/nZ nZINY p DUT, 2AL i aR, ake Cy oscilloscope GNO Vee TI. SVO1889 Figure 9. Test circuit for measuring crosstalk between control and any switch. Figure 11. Test circuit for measuring sine-wave distortion. 1998 Jun 23 NOTE TO FIGURE 9: Veo Adjust input voltage to obtain 0 dBm at Vos when Fin = 1 MHz. After set-up frequency of fj, is increased to obtain a reading of -3 dB at Vos. Ome nY/nZ nzay nenave Ye sine-wave bd channet 2A, =e CL (a8) ON GND SVO1667 Figure 10. Test circuit for measuring minimum frequency response. Vec Vec 2A . 10 uF nY_/nZ Dx] ft azinYn fig = 1 kHz fh Vos OT RF nypinz sine-wave | 76 | Vv. | Vv, - distortion 8 os channel aR, =e CL meter ON channel GND OFF Sve1691 GND Sv01692 Figure 12. Test circuit for measuring switch OFF signal feed-through. _arsr8cin Aner VeunteRonim tenmeiye) maemsnueapan Angers neoPhilips Semiconductors Dual 4-channel analog multiplexer/demultiplexer Product specification WAVEFORMS NOTES: 1. Vy=t5Vat27V<sVecos3.6V Vu = 0.5 x Vee at 2.7 V>Vee>3.6V 2. Voz and Voy are the typical output voltage drop that occur with the output load 3. Vx =VoL+0.3V at2.7 Vs Veco s3.6V Vx = Vor + 0.1 * Vec at 2.7 VoVec > 3.6 V Vy = Voy - 0.3 Vat 2.7 Vs Voo 53.6 V Vy = Vou ~ 0.1 x Veg at 2.7 V >Veco > 3.6 V INPUTS GND Vou OUTPUTS You SV01638 Figure 13. Input (Vj) to output (V5) propagation delays. 74LV4052 INPUTS GND Vee > > GUTPUT LOW-to-OFF OFF-to-LOW Vou ipHz> Vou _3 OUTPUT HIGH-to-OFF OFF-to- HIGH GND------- outputs enabled SV01640 Figure 14. Turn-on and turn-off times for the inputs (S,, E) to the output (V95). TEST CIRCUIT 2-Voco O Open Om Vee PULSE GENERATOR Veg Test Circuit for Outputs Voc Vi Test Si Vis <2.7V Voc terHAPHL Open Pulse 2.7-3.6V; 2.7V tpizitpz, | 2-Vec VEE >3.6V 1 Voc teyziftezH | = Vee vi ww 30% > 90% NEGATIVE | \ Ym PULSE 10% po OV Po ke trae tty) | try (ty) i i > > tty (t) ~ ie frre (t) 1 ; i 90% 90% vi POSITIVE | v v PULSE oe My 10% f | 10% fi yy ee NDR DEFINITIONS R, = Load resistor C, = Load capacitance includes jig and probe capacitance Ry = Termination resistance should be equal to Zour of pulse generators. tp= t =6ns, when measuring fmax, there is no constraint on t,, ts with 50% duty factor. SY01738 Figure 15. Load circuitry for switching times. 1998 Jun 23Philips Semiconductors Product specification Dual 4-channel analog multiplexer/demultiplexer 74LV4052 DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4 2 8 Q 8 4_f 4 1 L | +] 1 i od ~] b> bo 16 | of My Mri) C4 F pin 1 index ' | yo --L E | | t Le be KS RA LG AI 1 a 0 5 10mm Lehn edeh | scale DIMENSIONS (inch dimensions are derived from. the original mm dimensions) A A A 4 4 2 UNIT | ax | mit. | max | by bz ec | oY | EM] e; L Me | My | w | 2 1.73 | 053 | 1.25 | 036 | 1950] 6.48 3.60 | 8.25 | 10.0 mm | 42 7 051 | 32 1 430 | 038 | 095 | 023 | 1855] 6.20 | 754 | 782 | 305 | 7.80] a3 | 2754] 0.76 ; 0.068 | 0.021 | 0.049 | 0.014 | 0.77 | 0.26 0.14 | 0.32 | 0.39 inches | 0.17 | 0.020} 0.13 | 9/951 | o.015 | 0.033 | 0.009 | 0.73 | 0.24 | 19 | %39 | go 42 | 034 | 033 | 97 | 0.030 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE REFERENCES EUROPEAN ISSUE DATE VERSION IEC JEDEC EIAJ PROJECTION BO SOTS8-4 EI} @ 95-01-14 1998 Jun 23 12Philips Semiconductors Product specification Dual 4-channel analog multiplexer/demultiplexer 74LV4052 SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 at D Te ly] Zz AAI AAR Lo of 7 Sum MA | - . f Ey EEO GEE EE. Heh ! 0 25 5mm a ae ee ee | scale DIMENSIONS (inch dimensions are derived from the origina) mm dimensions) unit | 4 Ay | Az | Ag | bp pM) | eM] e He L bp a v w y 2) ) 8 max. mm [175 | O40 | 128 | 92] oss[ors| 03 | 38 | 7] 55 [19] oe | oo | 225] 225] 91 | os | go inches | 0.009|0 peel oaea| |orslooore| os | ore |%| o29 [2 gore] ooze] 29% | 201 [ooos| Secs) vom : 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. REFERENCES ROPEAN VERSION lec JEDEC EIAJ PROJECTION ISSUE DATE soTi09-1 076E07S MS-012AC &-4+ Sens 1998 Jun 23 13Philips Semiconductors Product specification Dual 4-channel analog multiplexer/demultiplexer 74LV4052 SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1 = i 4 ry] } T \ } - ~ ~ ~ 7 ~ Fr ~ a Ay] He rh fs ARARAR RR : 1 Le -- {------ Ty! au (Aa) pin 1 index om enna TAROT 0 25 5mm Le scale DIMENSIONS (mm are the original dimensions) unr | At a, | Aa | As | bp | e | OM L eM) ec | He | Lap] a] v lw] y tz] o 0.21 1.80 0.38 | 0.20 6.4 5.4 7.9 1.03 0.9 1.00 a mm | 2.0 | gos | 165 | *5 | 025 | 008] 60 | 52 |] ze | 1251063 | o7 | &2 1% | Ot | O55] oe Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE REFERENCES EUROPEAN ISSUE DATE VERSION IEC JEDEC BIAJ PROJECTION SOT338-1 MO-150AC =} 95-02-04 1998 Jun 23 14Philips Semiconductors Product specification Dual 4-channel analog multiplexer/demultiplexer 74LV4052 TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 hy | a ARRAA BAA | | a | ae pin 1 index | O 1 ui Ht H te ! fe] p eb ah o- | >- _ 0 2.5 5mm Ld scale DIMENSIONS (mm are the original dimensions) A UNIT | ax. | At | Az | As | bp | | DM) EB] e | He | L [| bp | @ v w y | 2] 6 0.15 | 0.95 0.30 0.2 5.1 45 6.6 0.75 04 0.40 8 mm 1 149) gos | ago | 975] o19] 01 | 49 | 43 | 8] 62] ' | osot os | 97 | F] 91 | oe] 0 Notes 1. Plastic or metal protrusions of 0.15 mm maxdmum per.side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTUNE REFERENCES EUROPEAN ISSUE DATE VERSION IEC JEDEC EIAJ PROJECTION . 64-97-42. SOT403-1 MO-153 E40 oe0404 1998 Jun 23 15Philips Semiconductors Product specification Dual 4-channel analog multiplexer/demultiplexer 74LV4052 DEFINITIONS Data Sheet Identification Product Status Definition . Specitication Formative or in Design This data sheet contains the design target or goal specifications for product development. Specifications May change in any mariner without notice. This data sheet contains pretiminary data, and supplementary data will be published at a later date. Philips Preliminary Specitication Preproduction Product Semiconductors reserves the right to make changes al any time without notice in order to improve design and supply the best possible product. te . This data sheet contains Fina! Specifications. Philips Semiconductors reserves the right to make changes uct Specification Full Production at any time without notice, in order to improve design and supply the best possible product. Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless othrwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so ai their own risk and agree to fully indemnity Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. Philips Semiconductors Copyright Philips Electronics North America Corporation 1998 811 East Arques Avenue All rights reserved. Printed in U.S.A. P.O. Box 3409 Sunnyvale, California 94088-3409 print code Date of release: 05-96 Telephone 800-234-7381 Document order number: 9397-750-04461 PHILIPS Philips Semiconductors yyyy mmm dd 16