23
• General Purpose Dielectric for Ceramic Capacitors
• EIA Class II Dielectric
• Temperature variation of capacitance is within ±15%
from -55°C to +85°C
• Well suited for decoupling and filtering applications
• Available in High Capacitance values (up to 100µF)
X5R Dielectric
General Specifications
PART NUMBER (see page 2 for complete part number explanation)
GENERAL DESCRIPTION
% Capacitance
-60 -40 -20 0 +20 +40 +60 +80
Temperature °C
Temperature Coefficient
20
15
10
5
0
-5
-10
-15
-20
TYPICAL ELECTRICAL CHARACTERISTICS
Insulation Resistance (Ohm-Farads)
1,000
10,000
100
0
Insulation Resistance vs Temperature
020 120
40 60 80
Temperature °C
100
1210
Size
(L" x W")
4
Voltage
4 = 4V
6 = 6.3V
Z = 10V
Y = 16V
3 = 25V
D = 35V
5 = 50V
D
Dielectric
D = X5R
107
Capacitance
Code (In pF)
2 Sig. Digits +
Number of
Zeros
M
Capacitance
Tolerance
K = ±10%
M = ±20%
A
Failure
Rate
A = N/A
T
Terminations
T = Plated Ni
and Sn
2
Packaging
2 = 7" Reel
4 = 13" Reel
7 = Bulk Cass.
9 = Bulk
A
Special
Code
A = Std.
NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers.
Contact factory for non-specified capacitance values.
24
X5R Dielectric
Specifications and Test Methods
Parameter/Test X5R Specification Limits Measuring Conditions
Operating Temperature Range -55ºC to +85ºC Temperature Cycle Chamber
Capacitance Within specified tolerance
2.5% for 50V DC rating Freq.: 1.0 kHz ± 10%
Dissipation Factor 3.0% for 25V DC rating Voltage: 1.0Vrms ± .2V
12.5% Max. for 16V DC rating and lower For Cap > 10 µF, 0.5Vrms @ 120Hz
Contact Factory for DF by PN
Insulation Resistance 10,000MΩ or 500MΩ - µF, Charge device with rated voltage for
whichever is less 120 ± 5 secs @ room temp/humidity
Charge device with 300% of rated voltage for
Dielectric Strength No breakdown or visual defects 1-5 seconds, w/charge and discharge current
limited to 50 mA (max)
Appearance No defects Deflection: 2mm
Capacitance Test Time: 30 seconds
Resistance to Variation ±12%
Flexure Dissipation Meets Initial Values (As Above)
Stresses Factor
Insulation Initial Value x 0.3
Resistance
Solderability 95% of each terminal should be covered Dip device in eutectic solder at 230 ± 5ºC
with fresh solder for 5.0 ± 0.5 seconds
Appearance No defects, <25% leaching of either end terminal
Capacitance
Variation ±7.5%
Dip device in eutectic solder at 260ºC for 60
Dissipation Meets Initial Values (As Above) seconds. Store at room temperature for 24 ± 2
Resistance to Factor hours before measuring electrical properties.
Solder Heat Insulation Meets Initial Values (As Above)
Resistance
Dielectric Meets Initial Values (As Above)
Strength
Appearance No visual defects Step 1: -55ºC ± 2º 30 ± 3 minutes
Capacitance
Variation ±7.5% Step 2: Room Temp 3 minutes
Dissipation Meets Initial Values (As Above) Step 3: +85ºC ± 2º 30 ± 3 minutes
Thermal Factor
Shock Insulation Meets Initial Values (As Above) Step 4: Room Temp 3 minutes
Resistance
Dielectric Meets Initial Values (As Above) Repeat for 5 cycles and measure after
Strength 24 ± 2 hours at room temperature
Appearance No visual defects
Capacitance
Variation ±12.5%
Dissipation Initial Value x 2.0 (See Above)
Load Life Factor
Insulation Initial Value x 0.3 (See Above)
Resistance
Dielectric Meets Initial Values (As Above)
Strength
Appearance No visual defects
Capacitance
Variation ±12.5%
Load Dissipation Initial Value x 2.0 (See Above)
Humidity Factor
Insulation Initial Value x 0.3 (See Above)
Resistance
Dielectric Meets Initial Values (As Above)
Strength
Charge device with 1.5X rated voltage in
test chamber set at 85ºC ± 2ºC for 1000 hours
(+48, -0). Note: Contact factory for *optional
specification part numbers that are tested at
< 1.5X rated voltage.
Remove from test chamber and stabilize
at room temperature for 24 ± 2 hours
before measuring.
Store in a test chamber set at 85ºC ± 2ºC/
85% ± 5% relative humidity for 1000 hours
(+48, -0) with rated voltage applied.
Remove from chamber and stabilize at
room temperature and humidity for
24 ± 2 hours before measuring.
1mm/sec
90 mm
25
X5R Dielectric
Capacitance Range
PREFERRED SIZES ARE SHADED
SIZE 0201 0402 0603 0805 1206 1210 1812
Soldering Reflow Only Reflow/Wave Reflow/Wave Reflow/Wave Reflow/Wave Reflow Only Reflow Only
Packaging All Paper All Paper All Paper Paper/Embossed Paper/Embossed Paper/Embossed All Embossed
(L) Length mm 0.60 ± 0.03 1.00 ± 0.10 1.60 ± 0.15 2.01 ± 0.20 3.20 ± 0.20 3.20 ± 0.20 4.50 ± 0.30
(in.) (0.024 ± 0.001) (0.040 ± 0.004) (0.063 ± 0.006) (0.079 ± 0.008) (0.126 ± 0.008) (0.126 ± 0.008) (0.177 ± 0.012)
(W) Width mm 0.30 ± 0.03 0.50 ± 0.10 0.81 ± 0.15 1.25 ± 0.20 1.60 ± 0.20 2.50 ± 0.20 3.20 ± 0.20
(in.) (0.011 ± 0.001) (0.020 ± 0.004) (0.032 ± 0.006) (0.049 ± 0.008) (0.063 ± 0.008) (0.098 ± 0.008) (0.126 ± 0.008)
(t) Terminal mm 0.15 ± 0.05 0.25 ± 0.15 0.35 ± 0.15 0.50 ± 0.25 0.50 ± 0.25 0.50 ± 0.25 0.61 ± 0.36
(in.) (0.006 ± 0.002) (0.010 ± 0.006) (0.014 ± 0.006) (0.020 ± 0.010) (0.020 ± 0.010) (0.020 ± 0.010) (0.024 ± 0.014)
WVDC 4 6.3 10 16 25 4 6.3 10 16 25 50 4 6.3 10 16 25 35 50 6.3 10 16 25 35 50 6.3 10 16 25 35 50 4 6.3 10 16 25 35 50 6.3 10 25 50
Cap 100 A
(pF) 150 A
220 A C
330 A C
470 A C
680 A C
1000 A A C
1500 A C
2200 A A C
3300 A C
4700 A C G
6800 A C G
Cap 0.010 A C G
(µF) 0.015 C G G G
0.022 A
*
CC GGG N
0.033 C G G G N
0.047 A
*
CC GGG N
0.068 C G G N
0.10 A
*
CCC G G N N
0.15 GNN
0.22 A
*
A
*
C
*
GG NN Q
0.33 G G N
0.47 C
*
C
*
GNQQ X
0.68 G N
1.0 C
*
C
*
C
*
GGGJ
*
NN P* QQ XXX
1.5
2.2 C
*
C
*
G
*
G
*
J
*
J
*
NNN QQ Z X
3.3 J
*
J
*
J
*
J
*
NN QQ
4.7 E
*
J
*
J
*
J
*
NNN
*
N* QQQQ QZ
10 K J
*
N
*
N
*
N
**
QQQQ
*
XZZ
*
Z
22 N*
*
Q
*
Q
*
Q
*
ZZZZ
*
47 *Q
*
Z
*
100 Z
*
Z*
WVDC 4 6.3 10 16 25 4 6.3 10 16 25 50 4 6.3 10 16 25 35 50 6.3 10 16 25 35 50 6.3 10 16 25 35 50 4 6.3 10 16 25 35 50 6.3 10 25 50
SIZE 0201 0402 0603 0805 1206 1210 1812
= Under Development
= *Optional Specifications – Contact factory
L
W
T
t
NOTE: Contact factory for non-specified capacitance values
Letter A C E G J K M N P Q X Y Z
Max. 0.33 0.56 0.71 0.90 0.94 1.02 1.27 1.40 1.52 1.78 2.29 2.54 2.79
Thickness (0.013) (0.022) (0.028) (0.035) (0.037) (0.040) (0.050) (0.055) (0.060) (0.070) (0.090) (0.100) (0.110)
PAPER EMBOSSED