http://www.tracopower.com Page 1 of 3
DC/DC Converters
TEN 12WI Series, 12 Watt
Features
Ultrawide 4 : 1 input range
Full SMD-design
Input filter meets EN 55022, Class A and
FCC, level A without external components
Indefinite short-circuit protection
Overvoltage protection
I/O isolation 1500 VDC
operating temperature range
–40°C to 85°C
Remote On/Off (optional)
Insulated baseplate
Industry standard pinout
3-year product warranty
The TEN 12WI series is a family 12W DC/DC converter modules featuring ultra
wide 4:1 input voltage ranges in a compact 2“x1.0“ low profile package with in-
dustry-standard footprint.
A high efficiency up to 84% allows operating temperatures from –40°C to +85°C.
A built-in EMI input filter complies with EN 55022, class A without any external
components.
Further standard features include remote On/Off (optional), over voltage protec-
tion and continuous short-circuit protection.
Typical applications for these converters are battery operated equipment and distri-
buted power architectures in communication and industrial electronics, everywhere
where isolated, tightly regulated voltages are required.
Ordercode Input voltage range Output voltage Output current max. Efficiency typ.
TEN 12-2410 3,3 VDC 2‘400 mA 78 %
TEN 12-2411 5 VDC 2‘000 mA 82 %
TEN 12-2412 12 VDC 1‘000 mA 84 %
TEN 12-2413 9 – 36 VDC 15 VDC 800 mA 84 %
TEN 12-2421 (24 VDC nominal) ±5 VDC ±1‘000 mA 82 %
TEN 12-2422 ±12 VDC ±500 mA 84 %
TEN 12-2423 ±15 VDC ±400 mA 84 %
TEN 12-4810 3,3 VDC 2‘400 mA 78 %
TEN 12-4811 5 VDC 2‘000 mA 82 %
TEN 12-4812 12 VDC 1‘000 mA 84 %
TEN 12-4813 18 – 75 VDC 15 VDC 800 mA 84 %
TEN 12-4821 (48 VDC nominal) ±5 VDC ±1‘000 mA 82 %
TEN 12-4822 ±12 VDC ±500 mA 84 %
TEN 12-4823 ±15 VDC ±400 mA 84 %
Models
( U L195 0 )
not recommended for new design in
http://www.tracopower.com Page 2 of 3
All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.
DC/DC Converters
TEN 12WI Series 12 Watt
Input Specifications
Input current (no load) 24 Vin models: 40 mA typ.
48 Vin models: 20 mA typ.
Input current (full load) 24 Vin; 3.3 Vout models: 425 mA typ.
24 Vin; 5 & ±5 Vout models: 510 mA typ.
24 Vin; other output models: 600 mA typ.
48 Vin; 3.3 Vout models: 215 mA typ.
48 Vin; 5 & ±5 Vout models: 255 mA typ.
48 Vin; other output models: 300 mA typ.
Surge voltage (1 sec. max.) 24 Vin models: 42 V max..
48 Vin models: 84 V max.
Reverse voltage protection 1.0 A max.
Conducted noise (input) EN 55022 level A, FCC part 15, level A
Output Specifications
Voltage set accuracy ±1 %
Regulation – Input variation Vin min. to Vin max. ±0.5 % max.
– Load variation 10 – 90 % ±0.5 % max.
Ripple and noise (20 MHz Bandwidth) 50 mVpk-pk typ.
Temperature coefficient ±0.02 %/K
Output current limitation >110 % of Iout max. foldback
Short circuit protection indefinite (automatic recovery)
Capacitive load – single output models 470 µF max.
– dual output models 150 µF max.
General Specifications
Temperature ranges Operating –40°C to +85°C
– Case temperature +100°C max.
– Storage –55°C to +125°C
Derating above 60°C 2 %/K
Humidity (non condensing) 95 % rel H max.
Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >700’000 h
Isolation voltage (60 sec.) – Input/Output 1500 VDC
Isolation capacitance – Input/output) 200 pF typ
Isolation resistance – Input/Output (500 VDC) >1‘000 M Ohm
Switching frequency (fixed) 400 kHz typ. (pulse width modulation PWM)
Remote On/Off (optional): – On: 2.5 ... 5.5 VDC or open circuit.
– Off: 0 ... 0.8 VDC or short circuit pin 2 and pin 6
– Off idle current: 10 mA max.
Safety standards: UL 1950-1, EN 60950,1 IEC 60950
compliance up to 60 VDC input voltage (SELV limit)
Safety approvals: – UL 1950 (UL 60950-1 not intended) www.ul.com -> certifications -> File e188913
Environmental compliance – Reach www.tracopower.com/products/ten12wi-reach.pdf
– RoHS RoHS directive 2011/65/EU
Page 3 of 3
Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com
www.tracopower.com
DC/DC Converters
TEN 12WI Series 12 Watt
Physical Specifications
Casing material steel, nickel plated
Baseplate non conductive FR4
Potting material silicon rubber (UL 94 V-0 rated)
Weight 30 g (1.2 oz)
Soldering temperature max. 265°C / 10 sec.
Outline Dimensions
Pin Single Dual
1+Vin (Vcc) +Vin (Vcc)
2–Vin (GND) –Vin (GND)
3+Vout +Vout
4No pin Common
5–Vout –Vout
Pin-Out
Rev. April 11. 2014
Insulated baseplate
Bottom View
14
3
2
5
50.8
(2.0)
15.2
(0.60)
20.32
(0.80)
5.08
(0.20)
2.5
10.16
(0.40)
10.16
(0.40)
(1.0)
(0.24)
7.62
(0.30)
(0.10)
25.4
10.2
(0.40)
6.0
Dimensions in [mm], () = Inch
Pin diameter: 1.0 ±0.05 (0.02 ±0.002)
Pin pitsch tolerances: ±0.25 (±0.01)
Case tolerances: ±0.5 (±0.02)