CONDUCTING POLYMER ALUMINUM ELECTROLYTIC CAPACITORS FA Chip type, With Conducting Polymer Series Low ESR, high ripple current Designed for surface mounting on high density PC board Load life for 2000 hours at 105C Hi-CAP Item Characteristics Operating temperature range Leakage current max. 1 Capacitance tolerance Dissipation factor max. ESR -55 ~ +105 C Less than or equal to the value of Table1 20% at 120Hz, 20 C Less than or equal to the value of Table1 Less than or equal to the value of Table1 Z+25 C / Z+20 C 0.75~1.25 Z-55 C / Z+20 C 0.75~1.25 Temperature characteristics (Impedance ratio at 100kHz) Load life (after application of the rated voltage for 2000 hours at 105 C, In case of 25WV is applied 20V) Leakage current Capacitance change tan Less than specified value Within 20% of initial value Less than 150% of specified value Resistance to soldering heat (Refer to Page 36 for soldering recommendation) Leakage current Capacitance change tan Less than specified value Within 10% of initial value Less than 130% of specified value In case of some problems for measured values, measure the current after applying rated voltage for 120 minutes at 105 C. The rated voltage should be applied for 4 to 20WV, while 20V should be applied for 25WV. Positive B Negative Polarity Gold color case L +0.1 -0.4 D L A B C E R 6.3 6 6.3 5.9 2.4 6.6 6.6 2.2 0.5~0.8 8 6.2 8.0 6.9 3.3 8.3 8.3 3.1 0.8~1.1 10 10 10.0 7.9 3.2 10.3 10.3 4.5 0.8~1.1 E 0.2 D 0.5 100 6A Voltage C 0.2 A 0.2 0.3 max. Series Code 0.5 max. Plastic plateform Capacitance Lot No. PART NUMBER SYSTEM (See Page 34) (Unit : mm) A 0.2 DRAWING Negative R Voltage mark for 6.3V is 6 DIMENSIONS WV F 4.7 6.8 10 15 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 470 680 4 6.3 10 16 20 25 6.3 6.3 8 10 6.3 6 6.3 6 6 6.2 10 10 10 10 10 10 10 6.3 6 6.3 6 8 6.2 8 6.2 10 10 10 10 6.3 6 6.3 6 8 Case size 6.2 8 6.2 10 10 10 10 10 10 D L(mm) 6.3 6 6.3 6 8 6.2 8 6.2 10 10 10 10 6 8 6.2 10 10 CONDUCTING POLYMER ALUMINUM ELECTROLYTIC CAPACITORS FA series Table 1. FA(Chip type) Series Characteristics List L(mm) ESR(m )max at 20 C, 100~300kHz Ripple current (mArms) 45 C, 100kHz Dissipation factor at 20 C, 120Hz Leakage current ( F) max after 2 minutes 6.3 6 40 1810 0.12 120 330 8 6.2 35 2560 0.12 264 4 680 10 10 25 3700 0.12 544 6.3 82 6.3 6 45 1700 0.12 103 6.3 100 6.3 6 40 1810 0.12 126 6.3 220 10 10 25 3700 0.12 277 6.3 330 10 10 25 3700 0.12 416 6.3 470 10 10 25 3700 0.12 592 10 47 6.3 6 50 1620 0.12 94 10 56 6.3 6 45 1700 0.12 112 10 120 8 6.2 35 2560 0.12 240 10 150 8 6.2 35 2560 0.12 300 10 270 10 10 25 3700 0.12 540 10 330 10 10 25 3700 0.12 660 16 27 6.3 6 60 1450 0.10 86 16 39 6.3 6 50 1620 0.10 125 16 56 8 6.2 45 2120 0.12 179 16 82 8 6.2 40 2560 0.12 262 16 100 10 10 35 2670 0.12 320 16 150 10 10 30 3020 0.12 480 16 180 10 10 30 3020 0.12 576 20 22 6.3 6 60 1450 0.10 88 20 27 6.3 6 60 1450 0.10 108 20 33 8 6.2 45 1890 0.12 132 20 47 8 6.2 45 1890 0.12 188 20 56 10 10 40 2400 0.12 224 20 68 10 10 40 2400 0.12 272 25 6.8 6.3 6 80 1200 0.10 85 25 10 8 6.2 60 1500 0.10 125 25 22 10 10 50 2000 0.10 275 WV F 4 150 4 D(mm)