Print date 06/11/29
Nov, 2006
Multilayer Ceramic Antenna
for 870 MHz (12*4mm) CAN4311 129 070871K
CAN4311 129 080871K
CAN4311129 090871K
Asiawind Liu C.T.Lee Nov, 2006 Page 1 sheet 190-1
A4
spec.doc
WIDE BAND MULTILAYER CERAMIC ANTENNA
FOR 850~950MHz
Product Specification
QUICK REFERENCE DATA
Size 16.5*14*0.9 mm
Working Frequency 850~950MHz
Gain 1.5 dBi Max
VSWR 2 max
Polarization Linear
Azimuth Omni-directional
Impedance 50Ω
Operating Temperature -55~85 oC
Termination Ni/Sn (Environmentally-Friendly Leadless)
Resis()tance to soldering heats 260oC, 10 sec.
870MHz Ceramic Chip Antenna
(12*4 mm)
ANTENNA PRODUCTS
Nov, 2006, V1
Print date 06/11/29
Nov, 2006
Multilayer Ceramic Antenna
for 870 MHz (12*4mm) CAN4311 129 070871K
CAN4311 129 080871K
CAN4311129 090871K
Asiawind Liu C.T.Lee Nov, 2006 Page 2 sheet 190-2
A4
spec.doc
MULTILAYER CERAMIC ANTENNA (LINEAR POLARIZATION MODE)
FOR 800MHz~900MHz
Product Specification1
QUICK REFERENCE DATA
__________________________________________________________________________
Working Frequency* 800~900MHz
Bandwidth 20 MHz (Min)
Gain 0.5 dBi (Max)
VSWR 2.0 max
Polarization Linear
Azimuth Omni-directional
Impedance 50Ω
Operating Temperature -40~125 oC
Termination Ni/Sn (Environmentally-Friendly Leadless)
Resistance to soldering heat 260oC, 10 sec.
Special Environmenal Concerns- Green Products Design: The foil making process is
using environmentally friendly aqueous solvent technology. Termination is lead free and
packing materials can be re-cycled
1 All the technical data and information contained herein are subject to change without prior notice
Print date 06/11/29
Nov, 2006
Multilayer Ceramic Antenna
for 870 MHz (12*4mm) CAN4311 129 070871K
CAN4311 129 080871K
CAN4311129 090871K
Asiawind Liu C.T.Lee Nov, 2006 Page 3 sheet 190-3
A4
spec.doc
1. APPLICATION
2. SOLDER LAND PATTERN FOR ANTENNA
Figure Dimensions Remark
W
F
D
1.0 ± 0.15 mm
4.25 ± 0.15 mm
12.4 ± 0.15 mm
60 mm
Back side all ground plan
( But under antenna should avoid ground )
Cleanness
Circuits space
RF-
Module
40
50 ohm transmission line
D
F
8
W
Cleanness
Circuits space
RF-
Module
Print date 06/11/29
Nov, 2006
Multilayer Ceramic Antenna
for 870 MHz (12*4mm) CAN4311 129 070871K
CAN4311 129 080871K
CAN4311129 090871K
Asiawind Liu C.T.Lee Nov, 2006 Page 4 sheet 190-4
A4
spec.doc
3. MECHANICAL DATA
Figure Dimension Port
F W
L
T
F
4.1±0.2mm
12.1±0.2mm
1.6±0.2mm
0.85±0.35mm
Feed termination
Solder termination
4. TEST BOARD DIMENSION FOR S11 (RETURN LOSS) AND
RADIATION PATTERN MEASURNMENT
FR-4 PCB thickness = 0.8 mm
The length of transmission line = 60 mm ( depends on PCB thickness)
60 mm
40 50 ohm transmission
L
W
T
8
8
Print date 06/11/29
Nov, 2006
Multilayer Ceramic Antenna
for 870 MHz (12*4mm) CAN4311 129 070871K
CAN4311 129 080871K
CAN4311129 090871K
Asiawind Liu C.T.Lee Nov, 2006 Page 5 sheet 190-5
A4
spec.doc
5. S11 RETURN LOSS
Print date 06/11/29
Nov, 2006
Multilayer Ceramic Antenna
for 870 MHz (12*4mm) CAN4311 129 070871K
CAN4311 129 080871K
CAN4311129 090871K
Asiawind Liu C.T.Lee Nov, 2006 Page 6 sheet 190-6
A4
spec.doc
RELIABILITY DATA (Reference to IEC Specification)
IEC
384-10/
CECC 32
100
CLAUSE
IEC
6006868-2
TEST
METHOD
TEST
PROCEDURE
REQUIREMENTS
4.4 Mounting The antenna can be
mounted on printed-
circuit boards or ceramic
substrates by applying
wave soldering, reflow
soldering (including
vapour phase soldering)
or conductive adhesive
No visible damage
4.5 Visual inspection
and dimension
check
Any applicable method
using × 10 magnification
In accordance with
specification
4.6.1 Antenna Central Frequency
at 20°C Standard test board
in page 4
4.8 Adhesion A force of 5 N applied
for 10 s to the line
joining the terminations
and in a plane parallel to
the substrate
No visible damage
4.9 Bond strength of
plating on end face
Mounted in accordance
with CECC 32 100,
paragraph 4.4
No visible damage
Conditions: bending
0.25 mm at a rate of
1mm/s, radius jig. 340
mm,1 mm warp on FR4
board of 90 mm length
No visible damage
4.10 Tb Resistance to
soldering heat 260 ± 5 °C for 10 ± 0.5
s in a static solder bath The terminations
shall be well tinned
after recovery.
Print date 06/11/29
Nov, 2006
Multilayer Ceramic Antenna
for 870 MHz (12*4mm) CAN4311 129 070871K
CAN4311 129 080871K
CAN4311129 090871K
Asiawind Liu C.T.Lee Nov, 2006 Page 7 sheet 190-7
A4
spec.doc
IEC
384-10/
CECC 32
100
CLAUSE
IEC
6006868-2
TEST
METHOD
TEST
PROCEDURE
REQUIREMENTS
Resistance to
leaching 260 ± 5 °C for 30 ± 1 s
in a static solder bath Using visual
enlargement of × 10,
dissolution of the
termination shall not
exceed 10%
4.11 Ta Solderability Zero hour test, and test
after storage (20 to 24
months) in original
atmosphere; un-mounted
chips completely
immersed for 2 ± 0.5 s in
235 ± 5°C.
The termination must
be well tinned, at
least 75% is well
tinned at termination
Print date 06/11/29
Nov, 2006
Multilayer Ceramic Antenna
for 870 MHz (12*4mm) CAN4311 129 070871K
CAN4311 129 080871K
CAN4311129 090871K
Asiawind Liu C.T.Lee Nov, 2006 Page 8 sheet 190-8
A4
spec.doc
ORDERING INFORMATION:
The antenna may be ordered by using the ordering code. These code numbers can be
determined by the following rules:
CAN43 11 1 29 07 087 1K
F C M S T A P
F. Family Code
CAN43 = Antenna
C. Packing Type Code
11 = Tape
M. Materials Code
1 = High Frequency Material
S. Size Code
29 =12* 4 * 1.5 mm
T. Type
07 = central frequency 920MHz
08 = central frequency 870MHz
09 = central frequency 800MHz
A. Working Frequency
087 = 800~900MHz
P. Packing
1K = Tape packing, 1000pcs/reel
Print date 06/11/29
Nov, 2006
Multilayer Ceramic Antenna
for 870 MHz (12*4mm) CAN4311 129 070871K
CAN4311 129 080871K
CAN4311129 090871K
Asiawind Liu C.T.Lee Nov, 2006 Page 9 sheet 190-9
A4
spec.doc
Taping Blister Tape
Dimension
Serial no Cecking note
Index
Spec(mm)
1 Sprocket hole Do 1.5±0.10
2 Pocket hole D1 1.50±0.25
3 Distance sprocket hole/sprocket hole Po 4.0±0.10
4 Distance pocket/pocket P1 8.0±0.10
5 Distance sprocket hole/pocket P2 2.0±0.10
6 Tape width W 24.0±0.30
7 Distance sprocket hole/outside E 1.75±0.10
8 Distance sprocket hole/pocket F 11.50±0.10
9 Pocket length Ao 4.35±0.10
10 Pocket length Bo 12.45±0.10
11 Pocket depth Ko 1.85 ± 0.10
12 Thickness of tape T 0.3±0.10
13 10x sprocket hole pitch 10Po 40.0±0.20
Print date 06/11/29
Nov, 2006
Multilayer Ceramic Antenna
for 870 MHz (12*4mm) CAN4311 129 070871K
CAN4311 129 080871K
CAN4311129 090871K
Asiawind Liu C.T.Lee Nov, 2006 Page 10 sheet 190-10
A4
spec.doc
Reel Specifications
Product size
code Units per
Reel Tape Width
(mm) C
(mm) D
(mm) W1
(mm) W2
(mm)
Antenna 1000 24 180.0±1.0
62±0.5
16±0.5
20.5±0.5
Print date 06/11/29
Nov, 2006
Multilayer Ceramic Antenna
for 870 MHz (12*4mm) CAN4311 129 070871K
CAN4311 129 080871K
CAN4311129 090871K
Asiawind Liu C.T.Lee Nov, 2006 Page 11 sheet 190-11
A4
spec.doc
Revision Control:
Revision Date Content Remark
1 Nov. 2006 New Issued
