DATASHEET HA-5320 FN2857 Rev 10.00 August 11, 2015 1 Microsecond Precision Sample and Hold Amplifier The HA-5320 was designed for use in precision, high speed data acquisition systems. The circuit consists of an input transconductance amplifier capable of providing large amounts of charging current, a low leakage analog switch, and an output integrating amplifier. The analog switch sees virtual ground as its load; therefore, charge injection on the hold capacitor is constant over the entire input/output voltage range. The pedestal voltage resulting from this charge injection can be adjusted to zero by use of the offset adjust inputs. The device includes a hold capacitor. However, if improved droop rate is required at the expense of acquisition time, additional hold capacitance may be added externally. Features * Gain, DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 x 106 V/V * Acquisition Time . . . . . . . . . . . . . . . . . . . . . .1.0s (0.01%) * Droop Rate. . . . . . . . . . . . . . . . . . . . . 0.08V/s (+25C) 17V/s (Full Temperature) * Aperture Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25ns * Hold Step Error (See Glossary) . . . . . . . . . . . . . . . . . 5mV * Internal Hold Capacitor * Fully Differential Input * TTL Compatible This monolithic device is manufactured using the Intersil Dielectric Isolation Process, minimizing stray capacitance and eliminating SCRs. This allows higher speed and latchfree operation. For further information, please see Application Note AN538. * Pb-Free Available (RoHS Compliant) Pinouts * Auto Zero Circuits HA-5320 (CERDIP) TOP VIEW Applications * Precision Data Acquisition Systems * Digital to Analog Converter Deglitcher * Peak Detector Ordering Information -INPUT 1 14 S/H CONTROL +INPUT 2 13 SUPPLY GND OFFSET ADJUST 3 12 NC OFFSET ADJUST 4 11 CEXT PART NUMBER (Note 2) HA1-5320-2 PART MARKING 10 NC HA9P5320-5Z HA9P5320-5Z (Note 1) SIG. GND 6 9 V+ NOTES: OUTPUT 7 INTEGRATOR 8 BANDWIDTH -INPUT 1 16 S/H CONTROL +INPUT 2 15 SUPPLY GND OFFSET ADJUST 3 14 NC OFFSET ADJUST 4 13 CEXT V- 5 SIG. GND 6 OUTPUT 7 NC 8 FN2857 Rev 10.00 August 11, 2015 PACKAGE PKG. DWG. # HA1-5320-2 -55 to +125 14 Ld CERDIP F14.3 V- 5 HA-5320 (SOIC) TOP VIEW TEMP. RANGE (C) 0 to +75 16 Ld SOIC (Pb-free) M16.3 1. Add X96 for Tape and Reel. 2. Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 12 NC 11 V+ INTEGRATOR 10 BANDWIDTH 9 NC Page 1 of 11 HA-5320 Functional Diagram OFFSET ADJUST 3 V+ 9 4 100pF HA-5320 -INPUT 1 - +INPUT 2 7 + OUTPUT S/H CONTROL 14 13 5 SUPPLY GND V- 6 8 INTEGRATOR BANDWIDTH SIG. GND 11 CEXT FN2857 Rev 10.00 August 11, 2015 Page 2 of 11 HA-5320 Absolute Maximum Ratings Thermal Information Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24V Digital Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8V, -15V Output Current, Continuous (Note 1) . . . . . . . . . . . . . . . . . . . 20mA Thermal Resistance (Typical, Note 5) JA (C/W) JC (C/W) CERDIP Package. . . . . . . . . . . . . . . . . 70 18 SOIC Package . . . . . . . . . . . . . . . . . . . 90 N/A Maximum Junction Temperature (Ceramic Package) . . . . . . . . . 175C Maximum Junction Temperature (Plastic Package) . . . . . . . . 150C Maximum Storage Temperature Range . . . . . . . . . . -65C to 150C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300C (SOIC - Lead Tips Only) Pb-Free Reflow Profilesee link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Temperature Range HA-5320-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55C to 125C HA-5320-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 75C Supply Voltage Range (Typical, Note 2) . . . . . . . . . 13.5V to 20V CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 3. Internal Power Dissipation may limit Output Current below 20mA. 4. Specification based on a one time characterization. This parameter is not guaranteed. 5. JA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications VSUPPLY = 15.0V; CH = Internal; Digital Input: VIL = +0.8V (Sample), VIH = +2.0V (Hold), Unity Gain Configuration (Output tied to -Input), Unless Otherwise Specified HA-5320-2 HA-5320-5 TEMP. (C) MIN TYP MAX MIN TYP MAX UNITS Input Voltage Range Full 10 - - 10 - - V Input Resistance 25 1 5 - 1 5 - M Input Capacitance 25 - - 5 - - 5 pF Offset Voltage 25 - 0.2 - - 0.5 - mV Full - - 2.0 - - 1.5 mV 25 - 70 200 - 100 300 nA Full - - 200 - - 300 nA 25 - 30 100 - 30 300 nA Full - - 100 - - 300 nA Full 10 - - 10 - - V PARAMETER TEST CONDITIONS INPUT CHARACTERISTICS Bias Current Offset Current Common Mode Range CMRR VCM = 5V Offset Voltage Temperature Coefficient 25 80 90 - 72 90 - dB Full - 5 15 - 5 20 V/C TRANSFER CHARACTERISTICS Gain DC, (Note 14) 25 106 2 x 106 - 3 x 105 2 x 106 - V/V Gain Bandwidth Product (AV = +1, Note 7) CH = 100pF 25 - 2.0 - - 2.0 - MHz CH = 1000pF 25 - 0.18 - - 0.18 - MHz Output Voltage Full 10 - - 10 - - V Output Current 25 10 - - 10 - - mA OUTPUT CHARACTERISTICS Full Power Bandwidth Note 6 25 - 600 - - 600 - kHz Output Resistance Hold Mode 25 - 1.0 - - 1.0 - Total Output Noise (DC to 10MHz) Sample 25 - 125 200 - 125 200 VRMS Hold 25 - 125 200 - 125 200 VRMS FN2857 Rev 10.00 August 11, 2015 Page 3 of 11 HA-5320 Electrical Specifications VSUPPLY = 15.0V; CH = Internal; Digital Input: VIL = +0.8V (Sample), VIH = +2.0V (Hold), Unity Gain Configuration (Output tied to -Input), Unless Otherwise Specified (Continued) TEST CONDITIONS PARAMETER HA-5320-2 HA-5320-5 TEMP. (C) MIN TYP MAX MIN TYP MAX UNITS TRANSIENT RESPONSE Rise Time Note 7 25 - 100 - - 100 - ns Overshoot Note 7 25 - 15 - - 15 - % Slew Rate Note 8 25 - 45 - - 45 - V/s VIH Full 2.0 - - 2.0 - - V VIL Full - - 0.8 - - 0.8 V DIGITAL INPUT CHARACTERISTICS Input Voltage Input Current VIL = 0V 25 - - 4 - - 4 A Full - - 10 - - 10 A Full - - 0.1 - - 0.1 A To 0.1% 25 - 0.8 1.2 - 0.8 1.2 s To 0.01% 25 - 1.0 1.5 - 1.0 1.5 s Aperture Time (Note 10) 25 - 25 - - 25 - ns Effective Aperture Delay Time 25 -50 -25 0 -50 -25 0 ns Aperture Uncertainty 25 - 0.3 - - 0.3 - ns Droop Rate 25 - 0.08 0.5 - 0.08 0.5 V/s Full - 17 100 - 1.2 100 V/s 25 - 8 50 - 8 50 pA Full - 1.7 10 - 0.12 10 nA VIH = +5V SAMPLE AND HOLD CHARACTERISTICS Acquisition Time (Note 9) Drift Current Note 11 Charge Transfer Note 11 25 - 0.5 1.1 - 0.5 1.1 pC Hold Step Error Note 11 25 - 5 11 - 5 11 mV Hold Mode Settling Time To 0.01% Full - 165 350 - 165 350 ns Hold Mode Feedthrough 10VP-P, 100kHz Full - 2 - - 2 - mV Positive Supply Current Note 12 25 - 11 13 - 11 13 mA Negative Supply Current Note 12 25 - -11 -13 - -11 -13 mA Supply Voltage Range Note 4 13.5 20 13.5 - 20 V Power Supply Rejection V+, Note 13 Full 80 - - 80 - - dB V-, Note 13 Full 65 - - 65 - - dB POWER SUPPLY CHARACTERISTICS NOTES: 6. VO = 20VP-P; RL = 2k; CL = 50pF; unattenuated output. 7. VO = 200mVP-P; RL = 2k; CL = 50pF. 8. VO = 20V Step; RL = 2k; CL = 50pF. 9. VO = 10V Step; RL = 2k; CL = 50pF. 10. Derived from computer simulation only; not tested. 11. VIN = 0V, VIH = +3.5V, tR < 20ns (VIL to VIH). 12. Specified for a zero differential input voltage between +IN and -IN. Supply current will increase with differential input (as may occur in the Hold mode) to approximately 46mA at 20V. 13. Based on a 1V delta in each supply, i.e. 15V 0.5VDC. 14. RL = 1k, CL = 30pF. FN2857 Rev 10.00 August 11, 2015 Page 4 of 11 HA-5320 Test Circuits and Waveforms 1 2 S/H CONTROL INPUT 14 -INPUT OUTPUT 7 8 +INPUT 11 S/H CONTROL VO NC NC HA-5320 (CH = 100pF) FIGURE 1. CHARGE TRANSFER AND DRIFT CURRENT HOLD (+3.5V) SAMPLE (0V) S/H CONTROL HOLD (+3.5V) SAMPLE (0V) S/H CONTROL VO VO VO t VP NOTES: NOTES: 17. Observe the voltage "droop", VO/t. 15. Observe the "hold step" voltage VP. 18. Measure the slope of the output during hold, VO/t, and compute drift current: ID = CH VO/t. 16. Compute charge transfer: Q = VPCH. FIGURE 2. CHARGE TRANSFER TEST FIGURE 3. DRIFT CURRENT TEST V+ V IN 10VP-P 100kHz SINE WAVE AIN S/H CONTROL INPUT VHA-5320 ANALOG MUX OR SWITCH 9 1 -IN 2 +IN 14 OUT S/H CONTROL SUPPLY CEXT GND 13 TO SUPPLY COMMON NOTE: 5 11 NC REF COM 6 TO SIGNAL GND 7 VOUT INT. COMP. Feedthrough in V OUT dB = 20 log -------------V IN where: VOUT = VP-P, Hold Mode, VIN = VP-P. 8 NC FIGURE 4. HOLD MODE FEEDTHROUGH ATTENUATION Application Information Hold Capacitor The HA-5320 has the uncommitted differential inputs of an op amp, allowing the Sample and Hold function to be combined with many conventional op amp circuits. See the Intersil Application Note AN517 for a collection of circuit ideas. The HA-5320 includes a 100pF MOS hold capacitor, sufficient for most high speed applications (the Electrical Specifications section is based on this internal capacitor). Layout A printed circuit board with ground plane is recommended for best performance. Bypass capacitors (0.01F to 0.1F, ceramic) should be provided from each power supply terminal to the Supply Ground terminal on pin 13. The ideal ground connections are pin 6 (SIG. Ground) directly to the system Signal Ground, and pin 13 (Supply Ground) directly to the system Supply Common. FN2857 Rev 10.00 August 11, 2015 Additional capacitance may be added between pins 7 and 11. This external hold capacitance will reduce droop rate at the expense of acquisition time, and provide other trade-offs as shown in the Performance Curves. If an external hold capacitor CEXT is used, then a noise bandwidth capacitor of value 0.1CEXT should be connected from pin 8 to ground. Exact value and type are not critical. The hold capacitor CEXT should have high insulation resistance and low dielectric absorption, to minimize droop errors. Polystyrene dielectric is a good choice for operating temperatures up to +85C. Teflon(R) and glass dielectrics offer good performance to +125C and above. Page 5 of 11 HA-5320 The hold capacitor terminal (pin 11) remains at virtual ground potential. Any PC connection to this terminal should be kept short and "guarded" by the ground plane, since nearby signal lines or power supply voltages will introduce errors due to drift current. Aperture Time Typical Application Hold Step Error Figure 5 shows the HA-5320 connected as a unity gain noninverting amplifier - its most widely used configuration. As an input device for a fast successive - approximation A/D converter, it offers very high throughput rate for a monolithic IC sample/hold amplifier. Also, the HA-5320's hold step error is adjustable to zero using the Offset Adjust potentiometer, to deliver a 12-bit accurate output from the converter. Hold Step Error is the output error due to Charge Transfer (see above). It may be calculated from the specified parameter, Charge Transfer, using the following relationship: The application may call for an external hold capacitor CEXT as shown. As mentioned earlier, 0.1CEXT is then recommended at pin 8 to reduce output noise in the Hold mode. Effective Aperture Delay Time (EADT) The time required for the sample-and-hold switch to open, independent of delays through the switch driver and input amplifier circuitry. The switch opening time is the interval between the conditions of 10% open and 90% open. Charge Transfer (pC) Hold Step (V) = -----------------------------------------------------------Hold Capacitance (pF) See Performance Curves. The difference between the digital delay time from the Hold command to the opening of the S/H switch, and the propagation time from the analog input to the switch. The HA-5320 output circuit does not include short circuit protection, and consequently its output impedance remains low at high frequencies. Thus, the step changes in load current which occur during an A/D conversion are absorbed at the S/H output with minimum voltage error. A momentary short circuit to ground is permissible, but the output is not designed to tolerate a short of indefinite duration. EADT may be positive, negative or zero. If zero, the S/H amplifier will output a voltage equal to VIN at the instant the Hold command was received. For negative EADT, the output in Hold (exclusive of pedestal and droop errors) will correspond to a value of VIN that occurred before the Hold command. Aperture Uncertainty Glossary of Terms The range of variation in Effective Aperture Delay Time. Aperture Uncertainty (also called Aperture Delay Uncertainty, Aperture Time Jitter, etc.) sets a limit on the accuracy with which a waveform can be reconstructed from sample data. Acquisition Time The time required following a "sample" command, for the output to reach its final value within 0.1% or 0.01%. This is the minimum sample time required to obtain a given accuracy, and includes switch delay time, slewing time and settling time. Drift Current The net leakage current from the hold capacitor during the hold mode. Drift current can be calculated from the droop rate using the formula: Charge Transfer The small charge transferred to the holding capacitor from the inter-electrode capacitance of the switch when the unit is switched to the HOLD mode. Charge transfer is directly proportional to sample-to-hold offset pedestal error, where: Charge Transfer (pC) = CH (pF) x Hold Step Error (V) OFFSET ADJUST 15mV 10k S/H CONTROL 4 5 9 11 - - 13 7 + 14 INPUT DIGITAL OUTPUT CONVERT HA-5320 H S CEXT 100pF + 2 VIN -15V +15V HI-574A 3 1 V I D (pA) = C H pF -------- (V/s) t 13 6 5 8 0.1CEXT SYSTEM POWER GROUND SYSTEM SIGNAL GROUND 9 R/C ANALOG COMMON NOTE: Pin Numbers Refer to DIP Package Only. FIGURE 5. TYPICAL HA-5320 CONNECTIONS; NONINVERTING UNITY GAIN MODE FN2857 Rev 10.00 August 11, 2015 Page 6 of 11 HA-5320 Typical Performance Curves CH = 100pF, INTERNAL 10 ACQUISITION TIME FOR 10V STEP TO +0.01% (s) 5 1000 0.5 0.1 IDRIFT (pA) VOLTAGE DROOP DURING HOLD MODE, (mV/100ms) 1.0 SAMPLE-TO-HOLD OFFSET (HOLD STEP) ERROR, (mV) 0.05 0.01 100 100 10 1 1000 10k 0 100k -25 0 CH VALUE (pF) 25 50 75 100 TEMPERATURE (C) FIGURE 6. TYPICAL SAMPLE AND HOLD PERFORMANCE AS A FUNCTION OF HOLD CAPACITOR FIGURE 7. DRIFT CURRENT vs TEMPERATURE 100 0 80 45 PHASE 90 60 (CH = 100pF) GAIN GAIN (CH = 1100pF) 40 135 180 20 0 PHASE () GAIN (dB) 120 10 0 100 1k 10k 100k 1M 10M FREQUENCY (Hz) FIGURE 8. OPEN LOOP GAIN AND PHASE RESPONSE CH = 100pF TA = +25C -10 -8 -6 -4 5.0 CH = 100pF 0.5 CH = 1000pF 0.05 CH = 0.01F -2 2 4 6 +75C HOLD STEP VOLTAGE HOLD STEP VOLTAGE (mV) 8 DC INPUT (V) FIGURE 9A. HOLD STEP vs INPUT VOLTAGE 10 +25C 2 3 4 LOGIC LEVEL HIGH (V) 5 FIGURE 9B. HOLD STEP vs LOGIC (VIH) VOLTAGE FIGURE 9. TYPICAL SAMPLE-TO-HOLD OFFSET (HOLD STEP) ERROR FN2857 Rev 10.00 August 11, 2015 Page 7 of 11 125 HA-5320 Die Characteristics DIE DIMENSIONS: PASSIVATION: Type: Nitride (Si3N4) over Silox (SiO2, 5% Phos) Silox Thickness: 12kA 2kA Nitride Thickness: 3.5kA 1.5kA 92 mils x 152 mils x 19 mils METALLIZATION: Type: Al, 1% Cu Thickness: 16kA 2kA TRANSISTOR COUNT: 184 SUBSTRATE POTENTIAL: V- Metallization Mask Layout HA-5320 CEXT (11) SUPPLY GND (13) V+ (9) S/H CTRL (14) -INPUT (1) (8) INT BW (7) OUTPUT +INPUT (2) FN2857 Rev 10.00 August 11, 2015 (6) SIG GND (3) (4) (5) VIO ADJ VIO ADJ V- Page 8 of 11 HA-5320 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that you have the latest revision. DATE REVISION August 11, 2015 FN2857.10 CHANGE Added Rev History beginning with Rev 10. Added About Intersil Verbiage. Updated Ordering Information on page 1 About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/support FN2857 Rev 10.00 August 11, 2015 Page 9 of 11 HA-5320 Ceramic Dual-In-Line Frit Seal Packages (CERDIP) F14.3 MIL-STD-1835 GDIP1-T14 (D-1, CONFIGURATION A) 14 LEAD CERAMIC DUAL-IN-LINE FRIT SEAL PACKAGE LEAD FINISH c1 -D- -A- BASE METAL (c) E M -Bbbb S C A-B S Q -C- SEATING PLANE S1 b2 ccc M C A-B S D S eA/2 NOTES - 0.200 - 5.08 - 0.014 0.026 0.36 0.66 2 b1 0.014 0.023 0.36 0.58 3 b2 0.045 0.065 1.14 1.65 - b3 0.023 0.045 0.58 1.14 4 c 0.008 0.018 0.20 0.46 2 c1 0.008 0.015 0.20 0.38 3 D - 0.785 - 19.94 5 E 0.220 0.310 5.59 7.87 5 eA e b MAX b A A MIN A A L MILLIMETERS MAX M (b) D BASE PLANE MIN b1 SECTION A-A D S INCHES SYMBOL c aaa M C A - B S D S NOTES: 1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The manufacturer's identification shall not be used as a pin one identification mark. e 0.100 BSC 2.54 BSC - eA 0.300 BSC 7.62 BSC - eA/2 0.150 BSC 3.81 BSC - L 0.125 0.200 3.18 5.08 - Q 0.015 0.060 0.38 1.52 6 S1 0.005 - 0.13 - 7 105o 90o 105o - 2. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. 90o aaa - 0.015 - 0.38 - 3. Dimensions b1 and c1 apply to lead base metal only. Dimension M applies to lead plating and finish thickness. bbb - 0.030 - 0.76 - ccc - 0.010 - 0.25 - M - 0.0015 - 0.038 2, 3 4. Corner leads (1, N, N/2, and N/2+1) may be configured with a partial lead paddle. For this configuration dimension b3 replaces dimension b2. 5. This dimension allows for off-center lid, meniscus, and glass overrun. N 14 14 8 Rev. 0 4/94 6. Dimension Q shall be measured from the seating plane to the base plane. 7. Measure dimension S1 at all four corners. 8. N is the maximum number of terminal positions. 9. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 10. Controlling dimension: INCH. FN2857 Rev 10.00 August 11, 2015 Page 10 of 11 HA-5320 Small Outline Plastic Packages (SOIC) M16.3 (JEDEC MS-013-AA ISSUE C) N 16 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE INDEX AREA H 0.25(0.010) M B M INCHES E -B- 1 2 3 L SEATING PLANE -A- A D h x 45 -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A 0.0926 0.1043 2.35 2.65 - A1 0.0040 0.0118 0.10 0.30 - B 0.013 0.0200 0.33 0.51 9 C 0.0091 0.0125 0.23 0.32 - D 0.3977 0.4133 10.10 10.50 3 E 0.2914 0.2992 7.40 7.60 4 e B S 0.050 BSC 1.27 BSC - H 0.394 0.419 10.00 10.65 - h 0.010 0.029 0.25 0.75 5 L 0.016 0.050 0.40 1.27 6 N NOTES: MILLIMETERS 16 0 16 8 0 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. 7 8 Rev. 1 6/05 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width "B", as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. (c) Copyright Intersil Americas LLC 2003-2015. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN2857 Rev 10.00 August 11, 2015 Page 11 of 11