B57220K502J - EPCOS (TDK) - Datasheet.Live

NTC thermistors for

temperature measurement

Leadless NTCs

Series/Type: B57220K

Date: March 2013

information contained therein without EPCOS' prior express consent is prohibited.

EPCOS AG is a TDK Group Company.

1) Depends on mounting situation

Applications

Temperature measurement and

compensation

Features

Front surfaces silver-plated

For clamp contacting

UL approval (E69802)

Options

Alternative resistance ratings, rated

temperatures and resistance tolerances

available on request.

Delivery mode

Bulk

Dimensional drawing

∅d = 2.9 ±0.3 mm

th = 1.3 ±0.3 mm

Approx. weight 50 mg

General technical data

Climatic category (IEC 60068-1) 55/250/21

Max. power (at 25 °C) P25 180 mW

Resistance tolerance ∆RR/RR±5 %

Rated temperature TR20 °C

Dissipation factor (in air) δth1) approx. 2.5 mW/K

Thermal cooling time constant (in air) τc1) approx. 12 s

Heat capacity Cth1) approx. 30 mJ/K

Electrical specification and ordering codes

R20

ΩR25

ΩNo. of R/T

characteristic

B25/100

Ordering code

2.5 k 2056.9 1008 3560 ±1.5% B57220K0212A003

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 2 of 17Please read Cautions and warnings and

Important notes at the end of this document.

Reliability data

Test Standard Test conditions ∆R25/R25

(typical)

Remarks

Storage in

dry heat

IEC

60068-2-2

Storage at upper

category temperature

T: 250 °C

t: 1000 h

< 3% No visible

damage

Storage in damp

heat, steady state

IEC

60068-2-78

Temperature of air: 40 °C

Relative humidity of air: 93%

Duration: 21 days

< 3% No visible

damage

Rapid temperature

cycling

IEC

60068-2-14

Lower test temperature: 55 °C

Upper test temperature: 155 °C

Number of cycles: 100

< 3% No visible

damage

Endurance Pmax: 180 mW

t: 1000 h

< 3% No visible

damage

Long-term stability

(empirical value)

Temperature: 70 °C

t: 10000 h

< 5% No visible

damage

Note

Contact of NTC thermistors with any liquids and solvents shall be prevented. It must be

ensured that no water enters the NTC thermistors (e.g. through plug terminals).

Avoid dewing and condensation unless thermistor is specified for these conditions.

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 3 of 17Please read Cautions and warnings and

Important notes at the end of this document.

R/T characteristics

R/T No. 1008

T (°C) B25/100 = 3560 K T (°C) B25/100 = 3560 K T (°C) B25/100 = 3560 K

RT/R25 α(%/K) RT/R25 α(%/K) RT/R25 α(%/K)

55.0 53.104 6.1 50.0 0.40545 3.4 155.0 0.025193 2.0

50.0 39.318 6.0 55.0 0.3417 3.3 160.0 0.02279 2.0

45.0 29.325 5.8 60.0 0.28952 3.2 165.0 0.020667 2.0

40.0 22.03 5.7 65.0 0.24714 3.1 170.0 0.01878 1.9

35.0 16.666 5.5 70.0 0.21183 3.1 175.0 0.01709 1.9

30.0 12.696 5.4 75.0 0.18194 3.0 180.0 0.015582 1.8

25.0 9.7251 5.2 80.0 0.1568 2.9 185.0 0.014227 1.8

20.0 7.5171 5.1 85.0 0.13592 2.8 190.0 0.013012 1.8

15.0 5.8353 4.9 90.0 0.11822 2.8 195.0 0.011934 1.7

10.0 4.5686 4.8 95.0 0.1034 2.7 200.0 0.010964 1.7

5.0 3.605 4.7 100.0 0.090741 2.6 205.0 0.0101 1.7

0.0 2.8665 4.5 105.0 0.079642 2.6 210.0 0.0093191 1.6

5.0 2.2907 4.4 110.0 0.070102 2.5 215.0 0.0085949 1.6

10.0 1.8438 4.3 115.0 0.061889 2.4 220.0 0.0079384 1.6

15.0 1.492 4.1 120.0 0.054785 2.4 225.0 0.0073411 1.5

20.0 1.2154 4.0 125.0 0.048706 2.3 230.0 0.006798 1.5

25.0 1.0000 3.9 130.0 0.043415 2.3 235.0 0.0063087 1.5

30.0 0.82976 3.8 135.0 0.038722 2.2 240.0 0.0058623 1.5

35.0 0.68635 3.7 140.0 0.034615 2.2 245.0 0.0054487 1.4

40.0 0.57103 3.6 145.0 0.031048 2.1 250.0 0.0050705 1.4

45.0 0.48015 3.5 150.0 0.02791 2.1   

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 4 of 17Please read Cautions and warnings and

Important notes at the end of this document.

Mounting instructions

1 Soldering

1.1 Leaded NTC thermistors

Leaded thermistors comply with the solderability requirements specified by CECC.

When soldering, care must be taken that the NTC thermistors are not damaged by excessive

heat. The following maximum temperatures, maximum time spans and minimum distances have

to be observed:

Dip soldering Iron soldering

Bath temperature max. 260 °C max. 360 °C

Soldering time max. 4 s max. 2 s

Distance from thermistor min. 6 mm min. 6 mm

Under more severe soldering conditions the resistance may change.

1.2 Leadless NTC thermistors

In case of NTC thermistors without leads, soldering is restricted to devices which are provided

with a solderable metallization. The temperature shock caused by the application of hot solder

may produce fine cracks in the ceramic, resulting in changes in resistance.

To prevent leaching of the metallization, solder with silver additives or with a low tin content

should be used. In addition, soldering methods should be employed which permit short soldering

times.

1.3 SMD NTC thermistors

SMD NTC thermistors can be provided with a nickel barrier termination or on special request with

silver-palladium termination. The usage of mild, non-activated fluxes for soldering is recommend-

ed as well as a proper cleaning of the PCB.

Nickel barrier termination

The nickel barrier layer of the silver/nickel/tin termination (see figure 1) prevents leaching of the

silver base metalization layer. This allows great flexibility in the selection of soldering parameters.

The tin prevents the nickel layer from oxidizing and thus ensures better wetting by the solder. The

nickel barrier termination is suitable for all commonly-used soldering methods.

Note: SMD NTCs with AgPd termination are not approved for lead-free soldering.

Figure 1

SMD NTC thermistors, structure of nickel barrier

termination

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 5 of 17Please read Cautions and warnings and

Important notes at the end of this document.

1.3.1 Solderability (test to IEC 60068-2-58)

Preconditioning: Immersion into flux F-SW 32.

Evaluation criterion: Wetting of soldering areas ≥95%.

Solder Bath temperature (°C) Dwell time (s)

SnPb 60/40 215 ±3 3 ±0.3

SnAg (3.0 ... 4.0), Cu (0.5 ... 0.9) 245 ±3 3 ±0.3

1.3.2 Resistance to soldering heat (test to IEC 60068-2-58)

Preconditioning: Immersion into flux F-SW 32.

Evaluation criterion: Leaching of side edges ≤1/3.

Solder Bath temperature (°C) Dwell time (s)

SnPb 60/40 260 ±5 10 ±1

SnAg (3.0 ... 4.0), Cu (0.5 ... 0.9) 260 ±5 10 ±1

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 6 of 17Please read Cautions and warnings and

Important notes at the end of this document.

Wave soldering

Temperature characteristic at component terminal with dual wave soldering

Solder joint profiles for silver/nickel/tin terminations

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 7 of 17Please read Cautions and warnings and

Important notes at the end of this document.

Reflow soldering

Recommended temperature characteristic for reflow soldering following JEDEC J-STD-020D

Profile feature Sn-Pb eutectic assembly Pb-free assembly

Preheat and soak

- Temperature min Tsmin 100 °C 150 °C

- Temperature max Tsmax 150 °C 200 °C

- Time tsmin to tsmax 60 ... 120 s 60 ... 180 s

Average ramp-up rate Tsmax to Tp3°C/ s max. 3 °C/ s max.

Liquidous temperature TL183 °C 217 °C

Time at liquidous tL60 ... 150 s 60 ... 150 s

Peak package body temperature Tp1) 220 °C ... 235 °C2) 245 °C ... 260 °C2)

Time (tP)3) within 5 °C of specified

classification temperature (Tc)20 s3) 30 s3)

Average ramp-down rate Tpto Tsmax 6°C/ s max. 6 °C/ s max.

Time 25 °C to peak temperature maximum 6 min maximum 8 min

1) Tolerance for peak profile temperature (TP) is defined as a supplier minimum and a user maximum.

2) Depending on package thickness. For details please refer to JEDEC J-STD-020D.

3) Tolerance for time at peak profile temperature (tP) is defined as a supplier minimum and a user maximum.

Note: All temperatures refer to topside of the package, measured on the package body surface.

Number of reflow cycles: 3

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 8 of 17Please read Cautions and warnings and

Important notes at the end of this document.

Solder joint profiles for silver/nickel/tin terminations

1.3.3 Recommended geometry of solder pads

Recommended maximum dimensions (mm)

Case size

inch/mm

ABC

0402/1005 0.6 0.6 1.7

0603/1608 1.0 1.0 3.0

0805/2012 1.3 1.2 3.4

1206/3216 1.8 1.2 4.5

1.3.4 Notes

Iron soldering should be avoided, hot air methods are recommended for repair purposes.

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 9 of 17Please read Cautions and warnings and

Important notes at the end of this document.

2 Conductive adhesion

An alternative to soldering is the gluing of thermistors with conductive adhesives. The benefit of

this method is that it involves no thermal stress. The adhesives used must be chemically inert.

3 Clamp contacting

Pressure contacting by means of clamps is particularly suitable for applications involving frequent

switching and high turn-on powers.

4 Robustness of terminations (leaded types)

The leads meet the requirements of IEC 60068-2-21. They may not be bent closer than 4 mm

from the solder joint on the thermistor body or from the point at which they leave the feed-

throughs. During bending, any mechanical stress at the outlet of the leads must be removed. The

bending radius should be at least 0.75 mm.

Tensile strength: Test Ua1:

Leads ∅ ≤0.25 mm = 1.0 N

0.25 < ∅ ≤0.35 mm = 2.5 N

0.35 < ∅ ≤0.50 mm = 5.0 N

0.50 < ∅ ≤0.80 mm = 10.0 N

0.80 < ∅ ≤1.25 mm = 20.0 N

Bending strength: Test Ub:

Two 90°-bends in opposite directions at a weight of 0.25 kg.

Torsional strength: Test Uc: severity 2

The lead is bent by 90°at a distance of 6 to 6.5 mm from the thermistor body.

The bending radius of the leads should be approx. 0.75 mm. Two torsions of

180°each (severity 2).

When subjecting leads to mechanical stress, the following should be observed:

Tensile stress on leads

During mounting and operation tensile forces on the leads are to be avoided.

Bending of leads

Bending of the leads directly on the thermistor body is not permissible.

A lead may be bent at a minimum distance of twice the wire's diameter +2 mm from the solder

joint on the thermistor body. During bending the wire must be mechanically relieved at its outlet.

The bending radius should be at least 0.75 mm.

Twisting of leads

The twisting (torsion) by 180°of a lead bent by 90°is permissible at 6 mm from the bottom of the

thermistor body.

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 10 of 17Please read Cautions and warnings and

Important notes at the end of this document.

5 Sealing and potting

When thermistors are sealed, potted or overmolded, there must be no mechanical stress caused

by thermal expansion during the production process (curing / overmolding process) and during

later operation. The upper category temperature of the thermistor must not be exceeded. Ensure

that the materials used (sealing / potting compound and plastic material) are chemically neutral.

6 Cleaning

Washing processes may damage the product due to the possible static or cyclic mechanical

loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts,

which might lead to reduced reliability or lifetime.

7 Storage

In order to maintain their solderability, thermistors must be stored in a non-corrosive atmosphere.

Humidity, temperature and container materials are critical factors.

Do not store SMDs where they are exposed to heat or direct sunlight. Otherwise, the packing ma-

terial may be deformed or SMDs may stick together, causing problems during mounting. After

opening the factory seals, such as polyvinyl-sealed packages, use the SMDs as soon as possible.

The components should be left in the original packing. Touching the metallization of unsoldered

thermistors may change their soldering properties.

Storage temperature: 25 °Cupto45°C

Relative humidity (without condensation): ≤75% annual mean

<95%, maximum 30 days per annum

Solder the thermistors listed in this data book after shipment from EPCOS within the time speci-

fied:

SMDs with nickel barrier termination: 12 months

SMDs with AgPd termination: 6 months

Leaded components: 24 months

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 11 of 17Please read Cautions and warnings and

Important notes at the end of this document.

8 Placement and orientation of SMD NTC thermistors on PCB

a) Component placement

It is recommended that the PC board

should be held by means of some

adequate supporting pins such as

shown left to prevent the SMDs from

being damaged or cracked.

b) Cracks

When placing a component near an

area which is apt to bend or a grid

groove on the PC board, it is advisable

to have both electrodes subjected to

uniform stress, or to position the

component's electrodes at right angles

to the grid groove or bending line (see

c) Component orientation).

c) Component orientation

Choose a mounting position that

minimizes the stress imposed on the

chip during flexing or bending of the

board.

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 12 of 17Please read Cautions and warnings and

Important notes at the end of this document.

Cautions and warnings

See "Important notes".

Storage

Store thermistors only in original packaging. Do not open the package prior to storage.

Storage conditions in original packaging: storage temperature 25 °C ... +45 °C, relative

humidity ≤75% annual mean, <95% maximum 30 days per annum, dew precipitation is

inadmissible.

Do not store thermistors where they are exposed to heat or direct sunlight. Otherwise, the

packing material may be deformed or components may stick together, causing problems during

mounting.

Avoid contamination of thermistor surface during storage, handling and processing.

Avoid storage of thermistors in harmful environments like corrosive gases (SOx, Cl etc).

Use the components as soon as possible after opening the factory seals, i.e. the

polyvinyl-sealed packages.

Solder thermistors within the time specified after shipment from EPCOS.

For leaded components this is 24 months, for SMD components with nickel barrier termination

12 months, for SMD components with AgPd termination 6 months.

Handling

NTC thermistors must not be dropped. Chip-offs or any other damage must not be caused

during handling of NTCs.

Do not touch components with bare hands. Gloves are recommended.

Avoid contamination of thermistor surface during handling.

Washing processes may damage the product due to the possible static or cyclic mechanical

loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts,

which might lead to reduced reliability or lifetime.

Bending / twisting leads

A lead (wire) may be bent at a minimum distance of twice the wire’s diameter plus 4 mm from

the component head or housing. When bending ensure the wire is mechanically relieved at the

component head or housing. The bending radius should be at least 0.75 mm.

Twisting (torsion) by 180°of a lead bent by 90°is permissible at 6 mm from the bottom of the

thermistor body.

Soldering

Use resin-type flux or non-activated flux.

Insufficient preheating may cause ceramic cracks.

Rapid cooling by dipping in solvent is not recommended.

Complete removal of flux is recommended.

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 13 of 17Please read Cautions and warnings and

Important notes at the end of this document.

Mounting

Ensure that no thermo-mechanical stress occurs due to production processes (curing or

overmolding processes) when thermistors are sealed, potted or overmolded or during their

subsequent operation. The maximum temperature of the thermistor must not be exceeded.

Ensure that the materials used (sealing/potting compound and plastic material) are chemically

neutral.

Electrodes/contacts must not be scratched or damaged before/during/after the mounting

process.

Contacts and housing used for assembly with the thermistor must be clean before mounting.

Ensure that adjacent materials are designed for operation at temperatures comparable to the

surface temperature of the thermistor. Be sure that surrounding parts and materials can

withstand the temperature.

Avoid contamination of the thermistor surface during processing.

The connections of sensors (e.g. cable end, wire end, plug terminal) may only be exposed to

an environment with normal atmospheric conditions.

Tensile forces on cables or leads must be avoided during mounting and operation.

Bending or twisting of cables or leads directly on the thermistor body is not permissible.

Avoid using chemical substances as mounting aids. It must be ensured that no water or other

liquids enter the NTC thermistors (e.g. through plug terminals). In particular, water based

substances (e.g. soap suds) must not be used as mounting aids for sensors.

Operation

Use thermistors only within the specified operating temperature range.

Use thermistors only within the specified power range.

Environmental conditions must not harm the thermistors. Only use the thermistors under

normal atmospheric conditions or within the specified conditions.

Contact of NTC thermistors with any liquids and solvents shall be prevented. It must be

ensured that no water enters the NTC thermistors (e.g. through plug terminals). For

measurement purposes (checking the specified resistance vs. temperature), the component

must not be immersed in water but in suitable liquids (e.g. Galden).

Avoid dewing and condensation unless thermistor is specified for these conditions.

Bending or twisting of cables and/or wires is not permissible during operation of the sensor in

the application.

Be sure to provide an appropriate fail-safe function to prevent secondary product damage

caused by malfunction.

This listing does not claim to be complete, but merely reflects the experience of EPCOS AG.

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 14 of 17Please read Cautions and warnings and

Important notes at the end of this document.

Symbols and terms

Symbol English German

A Area Fläche

AWG American Wire Gauge Amerikanische Norm für Drahtquerschnitte

B B value B-Wert

B25/100 B value determined by resistance

measurement at 25 °C and 100 °C

B-Wert, ermittelt durch Widerstands-

messungen bei 25 °C und 100 °C

Cth Heat capacitance Wärmekapazität

I Current Strom

N Number (integer) Anzahl (ganzzahliger Wert)

P25 Maximum power at 25 °C Maximale Leistung bei 25 °C

Pdiss Power dissipation Verlustleistung

Pel Electrical power Elektrische Leistung

Pmax Maximum power within stated

temperature range

Maximale Leistung im

angegebenenTemperaturbereich

∆RB/RBResistance tolerance caused by

spread of B value

Widerstandstoleranz, die durch die

Streuung des B-Wertes verursacht wird

Rins Insulation resistance Isolationswiderstand

RPParallel resistance Parallelwiderstand

RRRated resistance Nennwiderstand

∆RR/RRResistance tolerance Widerstandstoleranz

RSSeries resistance Serienwiderstand

RTResistance at temperature T

(e.g. R25 = resistance at 25 °C)

Widerstand bei Temperatur T

(z.B. R25 = Widerstand bei 25 °C)

T Temperature Temperatur

∆T Temperature tolerance Temperaturtoleranz

t Time Zeit

TAAmbient temperature Umgebungstemperatur

Tmax Upper category temperature Obere Grenztemperatur

(Kategorietemperatur)

Tmin Lower category temperature Untere Grenztemperatur

(Kategorietemperatur)

Top Operating temperature Betriebstemperatur

TRRated temperature Nenntemperatur

Tsurf Surface temperature Oberflächentemperatur

V Voltage Spannung

Vins Insulation test voltage Isolationsprüfspannung

Vop Operating voltage Betriebsspannung

Vtest Test voltage Prüfspannung

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 15 of 17Please read Cautions and warnings and

Important notes at the end of this document.

Symbol English German

αTemperature coefficient Temperaturkoeffizient

∆Tolerance, change Toleranz, Änderung

δth Dissipation factor Wärmeleitwert

τcThermal cooling time constant Thermische Abkühlzeitkonstante

τaThermal time constant Thermische Zeitkonstante

Abbreviations / Notes

Symbol English German

Surface-mounted devices Oberflächenmontierbares Bauelement

* To be replaced by a number in ordering

codes, type designations etc.

Platzhalter für Zahl im Bestellnummern-

code oder für die Typenbezeichnung.

+ To be replaced by a letter. Platzhalter für einen Buchstaben.

All dimensions are given in mm. Alle Maße sind in mm angegeben.

The commas used in numerical values

denote decimal points.

Verwendete Kommas in Zahlenwerten

bezeichnen Dezimalpunkte.

Temperature measurement and compensation B57220K

Leadless NTCs K220

Page 16 of 17Please read Cautions and warnings and

Important notes at the end of this document.

The following applies to all products named in this publication:

1. Some parts of this publication contain statements about the suitability of our products for

certain areas of application. These statements are based on our knowledge of typical re-

quirements that are often placed on our products in the areas of application concerned. We

nevertheless expressly point out that such statements cannot be regarded as binding

statements about the suitability of our products for a particular customer application.

As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar

with them than the customers themselves. For these reasons, it is always ultimately incum-

bent on the customer to check and decide whether an EPCOS product with the properties de-

scribed in the product specification is suitable for use in a particular customer application.

2. We also point out that in individual cases, a malfunction of electronic components or

failure before the end of their usual service life cannot be completely ruled out in the

current state of the art, even if they are operated as specified. In customer applications

requiring a very high level of operational safety and especially in customer applications in

which the malfunction or failure of an electronic component could endanger human life or

health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by

means of suitable design of the customer application or other action taken by the customer

(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by

third parties in the event of malfunction or failure of an electronic component.

3. The warnings, cautions and product-specific notes must be observed.

4. In order to satisfy certain technical requirements, some of the products described in this

publication may contain substances subject to restrictions in certain jurisdictions (e.g.

because they are classed as hazardous). Useful information on this will be found in our Ma-

terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de-

tailed questions, please contact our sales offices.

5. We constantly strive to improve our products. Consequently, the products described in this

publication may change from time to time. The same is true of the corresponding product

specifications. Please check therefore to what extent product descriptions and specifications

contained in this publication are still applicable before or when you place an order. We also

reserve the right to discontinue production and delivery of products. Consequently, we

cannot guarantee that all products named in this publication will always be available. The

aforementioned does not apply in the case of individual agreements deviating from the fore-

going for customer-specific products.

6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-

sion of the "General Terms of Delivery for Products and Services in the Electrical In-

dustry" published by the German Electrical and Electronics Industry Association

(ZVEI).

7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS,

DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC,

MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL,

SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse,

WindCap are trademarks registered or pending in Europe and in other countries. Further

information will be found on the Internet at www.epcos.com/trademarks.

Important notes

Page 17 of 17