SN74LS132 Quad 2-Input Schmitt Trigger NAND Gate The SN74LS132 contains four 2-Input NAND Gates which accept standard TTL input signals and provide standard TTL output levels. They are capable of transforming slowly changing input signals into sharply defined, jitter-free output signals. Additionally, they have greater noise margin than conventional NAND Gates. Each circuit contains a 2-input Schmitt trigger followed by a Darlington level shifter and a phase splitter driving a TTL totem pole output. The Schmitt trigger uses positive feedback to effectively speed-up slow input transitions, and provide different input threshold voltages for positive and negative-going transitions. This hysteresis between the positive-going and negative-going input thresholds (typically 800 mV) is determined internally by resistor ratios and is essentially insensitive to temperature and supply voltage variations. As long as one input remains at a more positive voltage than VT+ (MAX), the gate will respond to the transitions of the other input as shown in Figure 1. http://onsemi.com LOW POWER SCHOTTKY 14 1 PLASTIC N SUFFIX CASE 646 LOGIC AND CONNECTION DIAGRAM DIP (TOP VIEW) VCC 14 13 12 11 10 9 8 14 1 1 2 3 4 5 6 SOIC D SUFFIX CASE 751A 7 GND GUARANTEED OPERATING RANGES Symbol VCC Parameter Supply Voltage Min Typ Max Unit 4.75 5.0 5.25 V 0 25 70 C TA Operating Ambient Temperature Range IOH Output Current - High - 0.4 IOL Output Current - Low 8.0 Semiconductor Components Industries, LLC, 1999 December, 1999 - Rev. 6 1 ORDERING INFORMATION Device Package Shipping mA SN74LS132N 14 Pin DIP 2000 Units/Box mA SN74LS132D 14 Pin 2500/Tape & Reel Publication Order Number: SN74LS132/D SN74LS132 VO, OUTPUT VOLTAGE (VOLTS) 5 VCC = 5 V TA = 25C 4 3 2 1 0 0 0.4 0.95 1.2 VIN, INPUT VOLTAGE (VOLTS) 1.8 2 Figure 1. VIN versus VOUT Transfer Function DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits Parameter Min Max Unit VT+ Positive-Going Threshold Voltage 1.5 2.0 V VCC = 5.0 V VT- Negative-Going Threshold Voltage 0.6 1.1 V VCC = 5.0 V VT + - VT- Hysteresis 0.4 V VCC = 5.0 V VIK Input Clamp Diode Voltage V VCC = MIN, IIN = - 18 mA VOH Output HIGH Voltage V VCC = MIN, IOH = - 400 A, VIN = VIL VOL O Output LOW Voltage IT+ Input Current at Positive-Going Threshold - 0.14 mA VCC = 5.0 V, VIN = VT+ IT- Input Current at Negative-Going Threshold - 0.18 mA VCC = 5.0 V, VIN = VT- IIH Input HIGH Current IIL Input LOW Current Symbol IOS ICC Output Short Circuit Current Typ 0.8 - 0.65 2.7 (1) - 1.5 3.4 Test Conditions 0.25 0.4 V VCC = MIN, IOL = 4.0 mA, VIN = 2.0 V 0.35 0.5 V VCC = MIN, IOL = 8.0 mA, VIN = 2.0 V - 20 20 A VCC = MAX, VIN = 2.7 V 0.1 mA VCC = MAX, VIN = 7.0 V - 0.4 mA VCC = MAX, VIN = 0.4 V -100 mA VCC = MAX, VOUT = 0 V Power Supply Current Total, Output HIGH 5.9 11 mA VCC = MAX, VIN = 0 V Total, Output LOW 8.2 14 mA VCC = MAX, VIN = 4.5 V Note 1: Not more than one output should be shorted at a time, nor for more than 1 second. AC CHARACTERISTICS (TA = 25C) Limits Symbol Parameter Min Typ Max Unit Test Conditions VCC = 5.0 V CL = 15 pF tPLH Turn-Off Delay, Input to Output 22 ns tPHL Turn-On Delay, Input to Output 22 ns http://onsemi.com 2 SN74LS132 3V 1.6 V VIN 0.8 V 0V tPHL tPLH 1.3 V VOUT 1.3 V V T, THRESHOLD VOLTAGE (VOLTS) V T, HYSTERESIS (VOLTS) Figure 2. AC Waveforms 2 TA = 25C VT+ 1.6 1.2 VT- 0.8 VT 0.4 0 4.5 4.75 5 5.25 VCC, POWER SUPPLY VOLTAGE (VOLTS) 5.5 V T, THRESHOLD VOLTAGE (VOLTS) V T, HYSTERESIS (VOLTS) Figure 3. Threshold Voltage and Hysteresis versus Power Supply Voltage 1.9 VT+ 1.7 1.5 1.3 1.1 VT- 0.9 0.7 - 55 VT 0 25 75 TA, AMBIENT TEMPERATURE (C) Figure 4. Threshold Voltage and Hysteresis versus Temperature http://onsemi.com 3 125 SN74LS132 PACKAGE DIMENSIONS 14 8 B 1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. N SUFFIX PLASTIC PACKAGE CASE 646-06 ISSUE M 7 A F DIM A B C D F G H J K L M N L N C -T- SEATING PLANE J K H D 14 PL G M 0.13 (0.005) 14 1 P 7 PL 0.25 (0.010) 7 G M B M R X 45 _ C F -T- SEATING PLANE NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 8 -B- D 14 PL 0.25 (0.010) T B J M K M S A MILLIMETERS MIN MAX 18.16 18.80 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.37 7.87 --- 10_ 0.38 1.01 M D SUFFIX PLASTIC SOIC PACKAGE CASE 751A-03 ISSUE F -A- INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.290 0.310 --- 10_ 0.015 0.039 S DIM A B C D F G J K M P R MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION North America Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong 800-4422-3781 Email: ONlit-asia@hibbertco.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (M-F 2:30pm to 5:00pm Munich Time) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (M-F 2:30pm to 5:00pm Toulouse Time) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (M-F 1:30pm to 5:00pm UK Time) Email: ONlit@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-8549 Phone: 81-3-5487-8345 Email: r14153@onsemi.com Fax Response Line: 303-675-2167 800-344-3810 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. http://onsemi.com 4 SN74LS132/D