LMH6584,LMH6585 LMH6584/LMH6585 32x16 400 MHz Analog Crosspoint Switches, Gain of 1, Gain of 2 Literature Number: SNOSB08A LMH6584/LMH6585 32x16 400 MHz Analog Crosspoint Switches, Gain of 1, Gain of 2 General Description Features LMH(R) The family of products is joined by the LMH6584 and the LMH6585 high speed, non-blocking, analog, crosspoint switches. The LMH6584/LMH6585 are designed for high speed, DC coupled, analog signals such as high resolution video (UXGA and higher). The LMH6584/LMH6585 have 32 inputs and 16 outputs. The non-blocking architecture allows an output to be connected to any input, including an input that is already selected. With fully buffered inputs the LMH6584/ LMH6585 can be impedance matched to nearly any source impedance. The buffered outputs of the LMH6584/LMH6585 can drive up to two back terminated video loads (75 load). The outputs and inputs also feature high impedance inactive states allowing high performance input and output expansion for array sizes such as 32 x 32 or 64 x 16 by combining two devices. The LMH6584/LMH6585 are controlled with a 4 pin serial interface. Both single serial mode and addressed chain modes are available. The LMH6584/LMH6585 come in 144-pin LQFP packages. They also have diagonally symmetrical pin assignments to facilitate double sided board layouts and easy pin connections for expansion. 32 inputs and 16 outputs 144-pin LQFP package -3 dB bandwidth (VOUT = 2 VPP, RL = 150) 400 MHz Fast slew rate 1200 V/s Channel to channel crosstalk (10/100 MHz) -52/ -43 dBc Easy to use serial programming 4 wire bus Two programming modes Serial & addressed modes Symmetrical pinout facilitates expansion. Output current 50 mA Applications Studio monitoring/production video systems Conference room multimedia video systems KVM (keyboard video mouse) systems Security/surveillance systems Multi antenna diversity radio Video test equipment Medical imaging Wide-band routers & switches Block Diagram 30045011 LMH(R) is a registered trademark of National Semiconductor Corporation. TRI-STATE(R) is a registered trademark of National Semiconductor Corporation. (c) 2008 National Semiconductor Corporation 300450 www.national.com LMH6584/LMH6585 32x16 400 MHz Analog Crosspoint Switches, Gain of 1, Gain of 2 October 21, 2008 LMH6584/LMH6585 Storage Temperature Range Soldering Information Infrared or Convection (20 sec.) Wave Soldering (10 sec.) Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 2) Human Body Model Machine Model VS IIN (Input Pins) IOUT Input Voltage Range Maximum Junction Temperature Operating Ratings 2000V 200V 6V 20 mA (Note 3) V- to V+ +150C 3.3V Electrical Characteristics -65C to +150C 235C 260C (Note 1) Temperature Range (Note 4) Supply Voltage Range Thermal Resistance 144-Pin TQFP -40C to +85C 3V to 5.5V JA 22C/W JC 5C/W (Note 5) Unless otherwise specified, typical conditions are: TA = 25C, VS = 3.3V, RL = 100. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Min (Note 8) Typ (Note 7) Max (Note 8) Units Frequency Domain Performance SSBW -3 dB Bandwidth LSBW LMH6584, VOUT = 0.25 VPP (Note 12) 350 LMH6585V, VOUT = 0.5 VPP (Note 12) 350 LMH6584, VOUT = 1VPP, RL = 1 k 375 (Note 12) LMH6585, VOUT = 2VPP, RL = 1 k 375 (Note 12) LMH6584, VOUT = 1VPP, RL = 150 MHz 375 (Note 12) LMH6585, VOUT = 2VPP, RL = 150 375 (Note 12) GF 0.1 dB Gain Flatness VOUT = 2 VPP, RL = 150 DG Differential Gain DP Differential Phase 50 MHz RL = 150, 3.58 MHz/ 4.43 MHz 0.06 % RL = 150, 3.58 MHz/ 4.43 MHz 0.04 deg LMH6584, 2V Step, 10% to 90% 2.0 ns LMH6585, 2 V Step, 10% to 90% 1.26 LMH6584, 2 V Step, 10% to 90% 1.75 LMH6585, V Step, 10% to 90% 1.0 Time Domain Response tr tf Rise Time Fall Time OS Overshoot SR Slew Rate LMH6584, 2 V Step LMH6585, 2 V Step ts Settling Time 0 ns % 5 LMH6584, 2 VPP, 20% to 80% 900 LMH6585, 2 VPP, 20% to 80% (Note 6) 1300 V/s 2V Step, VOUT within 0.5% 15 ns Distortion And Noise Response HD2 2nd Harmonic Distortion LMH6584, 1 VPP, 10 MHz -70 dBc HD3 3rd Harmonic Distortion 1 VPP, 10 MHz -75 dBc en Input Referred Voltage Noise >1 MHz 12 nV/Hz in Input Referred Current Noise >1 MHz 22 pA/Hz Switching Time 50 ns XTLK Crosstalk Channel to channel, f = 100 MHz -43 dBc ISOL Off Isolation f = 100 MHz -60 dBc www.national.com 2 Parameter Conditions Min (Note 8) Typ (Note 7) Max (Note 8) LMH6584 0.987 1.00 1.013 LMH6585 1.98 2.00 2.02 3 18 Units Static, DC Performance AVOL Voltage Gain V/V VOS Input Offset Voltage mV TCVOS Input Offset Voltage Temperature Drift (Note 10) 13 V/C IB Input Bias Current Non-Inverting (Note 9) -5 A TCIB Input Bias Current Average Drift Non-Inverting (Note 10) 4 nA/C VOUT Output Voltage Range RL = 100, LMH6584 -1.36, +1.38 1.6 RL = , LMH6584(Note 11) -1.36, +1.38 1.6 RL = 100, LMH6585 -1.82, +1.9 2.1 RL = , LMH6585 2.05 2.2 V PSRR Power Supply Rejection Ratio ICC Positive Supply Current RL = 189 45 250 mA dB IEE Negative Supply Current RL = 181 240 mA Tri State Supply Current RST Pin > 2.0V 30 50 mA 100 k Miscellaneous Performance RIN Input Resistance Non-Inverting CIN Input Capacitance Input connected to one output 9 pF CIN Input Capacitance Input connected to 16 outputs (Broadcast) 12 pF RO Output Resistance Enabled Closed Loop, Enabled 300 m Output Resistance Disabled Disabled, LMH6584 50 Output Resistance Disabled Disabled, LMH6585 1.3 CMVR Input Common Mode Voltage Range IO Output Current Sourcing, VO = 0 V k 0.8 V 45 mA Digital Control VIH Input Voltage High VIL Input Voltage Low 2.0 V VOH Output Voltage High >2.2 V VOL Output Voltage Low <0.4 V TS Setup Time 9 ns TH Hold Time 9 ns 0.8 3 V www.national.com LMH6584/LMH6585 Symbol LMH6584/LMH6585 5V Electrical Characteristics (Note 5) Unless otherwise specified, typical conditions are: TA = 25C, AV = +2, VS = 5V, RL = 100. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Min (Note 8) Typ (Note 7) Max (Note 8) Units Frequency Domain Performance SSBW -3 dB Bandwidth LSBW LMH6584, VOUT = 0.25 VPP (Note 12) 400 LMH6585, VOUT = 0.5 VPP (Note 12) 400 LMH6584, VOUT = 1VPP, RL = 1 k 400 (Note 12) 400 LMH6585, VOUT = 2 VPP, RL = 1 k MHz (Note 12) LMH6584, VOUT = 1VPP, RL = 150 400 (Note 12) LMH6585, VOUT = 2 VPP, RL = 150 400 (Note 12) GF 0.1 dB Gain Flatness VOUT = 2 VPP, RL = 150 50 MHz DG Differential Gain RL = 150, 3.58 MHz/ 4.43 MHz .04 % DP Differential Phase RL = 150, 3.58 MHz/ 4.43 MHz .03 deg LMH6584, 2V Step, 10% to 90% 1.75 ns LMH6585, 2V Step, 10% to 90% 1.25 LMH6584, 2V Step, 10% to 90% 1.5 LMH6585, 2V Step, 10% to 90% 1.1 Time Domain Response tr tf Rise Time Fall Time OS Overshoot 2V Step SR Slew Rate LMH6584, 2 VPP, 40% to 60% (Note 6) 1100 LMH6585, 2 VPP, 40% to 60% (Note 6) 1700 ts Settling Time ns 5 % V/s 2V Step, VOUT Within 0.5% 10 ns Distortion And Noise Response HD2 2nd Harmonic Distortion 2 VPP, 5 MHz -72 dBc HD3 3rd Harmonic Distortion 2 VPP, 5 MHz -68 dBc en Input Referred Voltage Noise >1 MHz 12 nV/Hz in Input Referred Noise Current >1 MHz 22 pA/Hz 50 ns Channel to Channel, f = 100 MHz -43 dBc Channel to Channel, f = 10 MHz -52 dBc f = 100 MHz -60 dBc Switching Time XTLK ISOL Crosstalk Off Isolation Static, DC Performance AVOL Voltage Gain LMH6584 0.987 1.00 1.013 LMH6585 1.98 2.00 2.02 18 VOS Input Offset Voltage Input Referred 2 TCVOS Input Offset Voltage Temperature Drift (Note 10) 21 IB Input Bias Current Non-Inverting (Note 9) -7 TCIB Input Bias Current Average Drift Non-Inverting (Note 10) 3.8 www.national.com 4 V/V mV V/C -12 A nA/C VOUT Parameter Output Voltage Range Conditions Min (Note 8) Typ (Note 7) RL = 100, LMH5484 -2.75 +2.9 3.1 RL = , LMH6584 2.9 3.2 RL = 100, LMH6585 -3.1 +3.3 3.6 RL = , LMH6585 3.7 3.9 Max (Note 8) Units V PSRR Power Supply Rejection Ratio DC 41 45 dB XTLK DC Crosstalk DC, Channel to Channel -60 -80 dB ISOL DC Off Isloation DC -72 -80 dB ICC Positive Supply Current RL = 210 265 mA IEE Negative Supply Current RL = 200 255 mA Tri State Supply Current RST Pin > 2.0V 37 60 mA 100 k Miscellaneous Performance RIN Input Resistance Non-Inverting CIN Input Capacitance Input connected to one output 9 pF CIN Input Capacitance Input connected to 16 outputs (Broadcast) 12 pF RO Output Resistance Enabled Closed Loop, Enabled 300 m Output Resistance Disabled Disabled, Resistance to Ground, LMH6584 50 Disabled, Resistance to Ground, LMH6585 CMVR Input Common Mode Voltage Range IO Output Current Sourcing, VO = 0 V k 1.1 1.3 1.4 2.5 3.1 V 60 80 mA Digital Control VIH Input Voltage High 2.0 V VIL Input Voltage Low VOH Output Voltage High >2.4 VOL Output Voltage Low <0.4 V TS Setup Time 8 ns TH Hold Time 8 ns 0.8 V V Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications, see the Electrical Characteristics tables. Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC) Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC). Note 3: The maximum output current (IOUT) is determined by device power dissipation limitations. Note 4: The maximum power dissipation is a function of TJ(MAX)and JA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/ JA. All numbers apply for packages soldered directly onto a PC Board. Note 5: Electrical Table values apply only for factory testing conditions at the temperature indicated. No guarantee of parametric performance is indicated in the electrical tables under conditions different than those tested. Note 6: Slew Rate is the average of the rising and falling edges. Note 7: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material. Note 8: Room Temperature limits are 100% production tested at 25C. Device self heating results in TJ TA, however, test time is insufficient for TJto reach steady state conditions. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. Note 9: Negative input current implies current flowing out of the device. Note 10: Drift determined by dividing the change in parameter at temperature extremes by the total temperature change. Note 11: This parameter is guaranteed by design and/or characterization and is not tested in production. Note 12: The channel bandwidth varies over the different channel combinations and with expansion. See the application section for more details. 5 www.national.com LMH6584/LMH6585 Symbol LMH6584/LMH6585 Block and Connection Diagram 144-Pin LQFP 30045002 Top View Ordering Information Package 144-Pin LQFP www.national.com Part Number Package Marking LMH6584VV LMH6584VV LMH6585VV LMH6585VV 6 Transport Media NSC Drawing 60 Units/Tray VNG144C Unless otherwise specified, typical conditions are: TA = 25C, AV = +1, VS = 5V, RL = 150. Boldface limits apply at the temperature extremes. 1 VPP Frequency Response 1 VPP Frequency Response 30045048 30045049 Small Signal Bandwidth Small Signal Bandwidth 30045024 30045025 Group Delay Group Delay Broadcast 30045054 30045041 7 www.national.com LMH6584/LMH6585 Typical Performance Characteristics LMH6584 LMH6584/LMH6585 Second Order Distortion (HD2) vs. Frequency Third Order Distortion (HD3) vs. Frequency 30045026 30045028 Second Order Distortion vs. Frequency Third Order Distortion vs. Frequency 30045029 30045027 Output Swing Output Swing 30045031 30045030 www.national.com 8 LMH6584/LMH6585 Output Swing over Temperature Output Swing over Temperature 30045032 30045033 Pulse Response Pulse Response 30045014 30045013 Input Impedance (Terminated Input) Enabled Output Impedance 30045074 30045075 9 www.national.com LMH6584/LMH6585 Disabled Output Impedance Input Referred Voltage Noise 30045076 30045081 Typical Performance Characteristics LMH6585 Unless otherwise specified, typical conditions are: TA = 25C, AV = +2, VS = 5V, RL = 150; Boldface limits apply at the temperature extremes. 2 VPP Frequency Response 2 VPP Frequency Response 30045055 www.national.com 30045056 10 LMH6584/LMH6585 Small Signal Frequency Response Small Signal Frequency Response 30045057 30045058 Group Delay Group Delay 30045059 30045060 Second Order Distortion (HD2) vs. Frequency Third Order Distortion (HD3) vs. Frequency 30045065 30045066 11 www.national.com LMH6584/LMH6585 Second Order Distortion (HD2) vs. Frequency Third Order Distortion (HD3) vs. Frequency 30045067 30045068 Output Swing Output Swing 30045069 30045070 Pulse Response Pulse Response 30045061 www.national.com 30045062 12 LMH6584/LMH6585 Large Signal Pulse Response Large Signal Pulse Response 30045063 30045064 Input Impedance (Terminated Input) Output Impedance 30045077 30045078 Input Referred Voltage Noise 30045080 13 www.national.com LMH6584/LMH6585 would be tied together (Input 0 on side 1 to input 31 on side 2 and so on) while the 16 output pins on each chip would be left separate. To make the 64 x 16 crosspoint, the 16 outputs would be tied together while all 64 inputs would remain independent. In the 64 x 16 configuration it is important not to have two connected outputs active at the same time. With the 32 x 32 configuration, on the other hand, having two connected inputs active is a valid state. Crosspoint expansion as detailed above has the advantage that the signal path has only one crosspoint in it at a time. Expansion methods that have cascaded stages will suffer bandwidth loss far greater than the small loading effect of parallel expansion. Output expansion is accomplished by connecting the crosspoint inputs and leaving the output pins on both chips separate. The input capacitance of the crosspoint pins is 9pF when an input is connected to one output and 12pF when an input is connected to 16 outputs. If the crosspoint is being driven by a 75 transmission line the bandwidth of the circuit will be limited by the RC time constand of the transmission line and the input capacitance of the two crosspoints. . In order to eliminate this bandwidth limitation it is necessary to drive the crosspoint inputs with a low impedance source. A circuit to accomplish this is show in Figure 1. The circuit shown in Figure 3 will suffer severe bandwidth limitations and is not recommended. Application Information INTRODUCTION The LMH6584/LMH6585 are high speed, fully buffered, non blocking, analog crosspoint switches. Having fully buffered inputs allow the LMH6584/LMH6585 to accept signals from low or high impedance sources without the worry of loading the signal source. The fully buffered outputs will drive 75 or 50 back terminated transmission lines with no external components other than the termination resistor. When disabled, the outputs are in a high impedance state. The LMH6584/ LMH6585 can have any input connected to any (or all) output (s). Conversely, a given output can have only one associated input. INPUT AND OUTPUT EXPANSION The LMH6584/LMH6585 have high impedance inactive states for both inputs and outputs allowing maximum flexibility for Crosspoint expansion. In addition the LMH6584/LMH6585 employ diagonal symmetry in pin assignments. The diagonal symmetry makes it easy to use direct pin to pin vias when the parts are mounted on opposite sides of a board. As an example two LMH6584/LMH6585 chips can be combined on one board to form either an 32 x 32 crosspoint or a 64 x 16 crosspoint. To make a 32 x 32 cross-point all 32 input pins 30045007 FIGURE 1. Output Expansion with Buffers www.national.com 14 30045073 FIGURE 2. Frequency Response for Buffered and Unbuffered Output expansion 30045043 FIGURE 4. Input Expansion with Shared Termination Resistors (Only 4 input and 4 output channels shown for illustration purposes.) 30045042 FIGURE 3. Output Expansion no Buffers (Only 4 input and 4 output channels shown for illustration purposes.) Input expansion requires more planning is also quite easy, but there are two different options for arranging the output termination resistors. As show in Figure 4 and Figure 5 there are two ways to connect the outputs of the crosspoint switches. In Figure 4 the crosspoint switch outputs are connected directly together and share one termination resistor. This is the easiest configuration to implement and has only one drawback. Because the disabled output of the unused crosspoint (only one output can be active at a time) has a small amount of capacitance, the frequency response of the active crosspoint will show peaking As illustrated in Figure 5 each crosspoint output can be given its own termination resistor. This results in a frequency response nearly identical to the non expansion case. There is one drawback for the gain of 2 crosspoint, and that is gain error. With a 75 termination resistor the 1250 resistance of the disabled crosspoint output will cause a gain error. In order to counteract this the termination resistors of both cross- 30045044 FIGURE 5. Input Expansion with Separate Termination Resistors (Only 4 input and 4 output channels shown for illustration purposes.) 15 www.national.com LMH6584/LMH6585 points should be adjusted to approximately 71. This will provide very good matching, but the gain accuracy of the system will now be dependent on the process variations of the crosspoint resistors which have a variability of approximately 20%. LMH6584/LMH6585 variation in bandwidth over all possible input/output combinations is shown in Figure 6. One particular pattern to note is that input channels 0 through 3 are slower than all other inputs. The use of input buffers as illustrated above can help equalize channel bandwidths. CHANNEL VARIATIONS The LMH6584/LMH6584 crosspoint switches have a very large number of possible channel combinations. There is some systematic variation in channel performance. Parameters such as bandwidth and distortion have a range of values depending on which channel combination is selected. The 30045003 FIGURE 6. Bandwidth Variation over Channel Combinations Because the inputs are the dominate factor in channel bandwidth it is possible to adjust the bandwith of the slower inputs. One method of increasing input bandwidth is with the use of buffers as illustrated in Figure 1. A simpler method using a single inductor is shown below in Figure 7. 30045082 FIGURE 7. Use of Termination Inductor to Increase Bandwidth 30045085 FIGURE 8. Termination Inductor Bandwidth Enhancement Using Input 0 The use of termination inductors can also be used when two crosspoints are used back to back for output expansion. The difference in input speeds between the opposing chips poses an additional challenge, especially if the channels that are connected together have very different performance. When connecting a slower channel (channels 0 to 3) to a faster channel the circuit shown in Figure 9 is recommended. In this case the inductor value is chosen to bring up the slow channel bandwidth, while the resistor RMis used to match the performance of the two channels. Larger values of RM will slow www.national.com 16 USING OUTPUT BUFFERING TO ENHANCE RELIABILITY The LMH6584/LMH6585 crosspoint switch can offer enhanced reliability with the use of external buffers on the outputs. For this technique to provide maximum benefit a very high speed amplifier such as the LMH6703 should be used, as shown in Figure 12 . The advantage offered by using external buffers is to reduce thermal loading on the crosspoint switch. This reduced die temperature will increase the life of the crosspoint. Another advantage is enhanced ESD reliability. It is very difficult to build high speed devices that can withstand all possible ESD events. With external buffers the crosspoint switch is isolated from ESD events on the external system connectors. 30045083 FIGURE 9. Inductor Termination with Mismatched Channels 30045040 FIGURE 12. Buffered Output In the example in Figure 12 the resistor RL is required to provide a load for the crosspoint output buffer. Without RLexcessive frequency response peaking is likely and settling times of transient signals will be poor. As the value of RL is reduced the bandwidth will also go down. The amplifier shown in the example is an LMH6703 this amplifier offers high speed and flat bandwidth. Another suitable amplifier is the LMH6702. The LMH6702 is a faster amplifier that can be used to generate high frequency peaking in order to equalize longer cable lengths. If board space is at a premium the LMH6739 or the LMH6734 are triple selectable gain buffers which require no external resistors. 30045084 FIGURE 10. Inductor Termination with Matched Channels CROSSTALK When designing a large system such as a video router, crosstalk can be a very serious problem. Extensive testing in our lab has shown that most crosstalk is related to board layout rather than the crosspoint switch. There are many ways to reduce board related crosstalk. Using controlled impedance lines is an important step. Using well decoupled power and ground planes will help as well. When crosstalk does occur within the crosspoint switch itself it is often due to signals coupling into the power supply pins. Using appropriate supply bypassing will help to reduce this mode of coupling. Another suggestion is to place as much grounded copper as possible between input and output signal traces. Care must be taken, though, not to influence the signal trace impedances by placing shielding copper too closely. One other caveat to consider is that as shielding materials come closer to the signal trace the trace needs to be smaller to keep the impedance from falling too low. Using thin signal traces will result in unacceptable losses due to trace resistance. This effect becomes even more pronounced at higher frequencies due to the skin effect. The skin effect reduces the effective thickness of the trace as frequency increases. Resistive losses make crosstalk worse because as the desired signal is attenuated 30045086 FIGURE 11. Termination Inductor Bandwidth Enhancement Using Input 0 Two LMH6585s Connected for Output Expansion DRIVING CAPACITIVE LOADS Capacitive output loading applications will benefit from the use of a series output resistor ROUT. Capacitive loads of 5 pF to 120 pF are the most critical, causing ringing, frequency response peaking and possible oscillation. As starting values, a capacitive load of 5 pF should have around 75 of isolation resistance. A value of 120 pF would require around 12. 17 www.national.com LMH6584/LMH6585 When driving transmission lines the 50 or 75 matching resistor normally provides enough isolation. down the faster channel and reduce peaking. When the channels connected together are relatively well matched the matching resistor is not needed as shown in Figure 10. LMH6584/LMH6585 with higher frequencies crosstalk increases at higher frequencies. The programming format of the incoming serial data is selected by the MODE pin. When the MODE pin is HIGH the crosspoint can be programmed one output at a time by entering a string of data that contains the address of the output that is going to be changed (Addressed Mode). When the MODE pin is LOW the crosspoint is in Serial Mode. In this mode the crosspoint accepts a 40 bit array of data that programs all of the outputs. In both modes the data fed into the chip does not change the chip operation until the configure pin is pulsed high. The configure and mode pins are independent of the chip select pin. DIGITAL CONTROL Block Diagram THREE WIRE VS. FOUR WIRE CONTROL There are two ways to connect the serial data pins. The first way is to control all four pins separately, and the second option is to connect the CFG and the CS pins together for a three wire interface. The benefit of the four wire interface is that the chip can be configured independently of the CS pin. This would be an advantage in a system with multiple crosspoint chips where all of them could be programmed ahead of time and then configured simultaneously. The four wire solution is also helpful in a system that has a free running clock on the CLK pin. In this case, the CS pin needs to be brought high after the last valid data bit to prevent invalid data from being clocked into the chip. The three wire option provides the advantage of one less pin to control at the expense of having less flexibility with the configure pin. One way around this loss of flexibility would be if the clock signal is generated by an FPGA or microcontroller where the clock signal can be stopped after the data is clocked in. In this case the Chip Select function is provided by the presence or absence of the clock signal. 30045011 FIGURE 13. Block Diagram The LMH6584/LMH6585 has internal control registers that store the programming states of the crosspoint switch. The logic is two staged to allow for maximum programming flexibility. The first stage of the control logic is tied directly to the crosspoint switching matrix. This logic consists of one register for each output that stores the on/off state and the address of which input to connect to. These registers are not directly accessible by the user. The second level of logic is another bank of registers identical to the first, but set up as shift registers. These registers are accessed by the user via the serial input bus. As described further below, there are two modes for programing the LMH6584/LMH6585, Serial Mode and Addressed Mode. The LMH6584/LMH6585 are programmed via a serial input bus with the support of four other digital control pins. The serial bus consists of a clock pin (CLK), a serial data in pin (DIN), and a serial data out pin (DOUT). The serial bus is gated by a chip select pin (CS). The chip select pin is active low. While the chip select pin is high all data on the serial input pin and clock pins is ignored. When the chip select pin is brought low the internal logic is set to begin receiving data by the first positive transition (0 to 1) of the clock signal. The chip select pin must be brought low at least 5 ns before the first rising edge of the clock signal. The first data bit is clocked in on the next negative transition (1 to 0) of the clock signal. All input data is read from the bus on the negative edge of the clock signal. Once the last valid data has been clocked in, the chip select pin must go high then the clock signal must make at least one more low to high transition. Otherwise invalid data will be clocked into the chip. The data clocked into the chip is not transferred to the crosspoint matrix until the CFG pin is pulsed high. This is the case regardless of the state of the MODE pin. The CFG pin is not dependent on the state of the chip select pin. If no new data is clocked into the chip subsequent pulses on the CFG pin will have no affect on device operation. www.national.com SERIAL PROGRAMMING MODE Serial programming mode is the mode selected by bringing the MODE pin low. In this mode a stream of 96-bits programs all 16 outputs of the crosspoint. The data is fed to the chip as shown in the Serial Mode Data Frame tables below (four tables are shown to illustrate the pattern). The tables are arranged such that the first bit clocked into the crosspoint register is labeled bit number 0. The register labeled Load Register in the block diagram is a shift register. If the chip select pin is left low after the valid data is shifted into the chip and if the clock signal keeps running then additional data will be shifted into the register, and the desired data will be shifted out. Also illustrated are the timing relationships for the digital pins in the Timing Diagram for Serial Mode shown below. It is important to note that all the pin timing relationships are important, not just the data and clock pins. One example is that the Chip Select pin (CS) must transition low before the first rising edge of the clock signal. This allows the internal timing circuits to synchronize to allow data to be accepted on the next falling edge. After the final data bit has been clocked in, the chip select pin must go high, then the clock signal must make at least one more low to high transition. As shown in the timing diagram, the chip select pin state should always occur while the clock signal is low. The configure (CFG) pin timing is not so critical, but it does need to be kept low until all data has been shifted into the crosspoint registers. 18 LMH6584/LMH6585 30045009 Timing Diagram for Serial Mode Serial Mode Data Frame (First Two Words) Output 0 Output 1 Input Address LSB 0 Off = 1 TRI-STATE(R), 2 3 On = 0 Input Address MSB Off = 1 LSB 4 5 6 7 On = 0 8 9 MSB Off = 1 10 11 Bit 0 is first bit clocked into device. Serial Mode Data Frame (Continued) Output 2 Output 3 Input Address On = 0 LSB 12 13 14 15 Input Address MSB Off = 1 LSB 16 17 18 19 On = 0 20 21 MSB Off = 1 22 23 MSB Off = 1 82 83 MSB Off = 1 94 95 Serial Mode Data Frame (Continued) Output 12 Output 13 Input Address LSB 72 73 74 75 On = 0 Input Address MSB Off = 1 LSB 76 77 78 79 On = 0 80 81 Serial Mode Data Frame (Last Two Words) Output 14 Output 15 Input Address LSB 84 85 86 87 On = 0 Input Address MSB Off = 1 LSB 88 89 90 91 On = 0 92 93 Bit 39 is last bit clocked into device. 19 www.national.com LMH6584/LMH6585 the data and clock pins. One example is that the Chip Select pin (CS) must transition low before the first rising edge of the clock signal. This allows the internal timing circuits to synchronize to allow data to be accepted on the next falling edge. After the final data bit has been clocked in, the chip select pin must go high, then the clock signal must make at least one more low to high transition. As shown in the timing diagram, the Chip Select pin state should always occur while the clock signal is low. The configure (CFG) pin timing is not so critical, but it does need to be kept low until all data has been shifted into the crosspoint registers. ADDRESSED PROGRAMMING MODE Addressed programming mode makes it possible to change only one output register at a time. To utilize this mode the mode pin must be High. All other pins function the same as in serial programming mode except that the word clocked in is 8 bits and is directed only at the output specified. In addressed mode the data format is shown in the table titled Addressed Mode Word Format. Also illustrated are the timing relationships for the digital pins in the Timing Diagram for Addressed Mode. It is important to note that all the pin timing relationships are important, not just 30045010 Timing Diagram for Addressed Mode Addressed Mode Word Format Output Address Input Address LSB 0 1 2 MSB LSB 3 4 5 Bit 0 is first bit clocked into device. www.national.com 20 TRISTATE 6 7 MSB 1 = TRISTATE 0 = On 8 9 30045012 Timing Diagram for Daisy Chain Operation SPECIAL CONTROL PINS should be budgeted 30 mW of power. For a typical application with one video load for each output this would be a total power The LMH6584/LMH6585 have two special control pins that of 2.5W. With a typical JA of 22C/W this will result in the function independent of the serial control bus. One of these silicon being 55C over the ambient temperature. A more agpins is the reset (RST) pin. The RST pin is active high meangressive application would be two video loads per output ing that at a logic 1 level the chip is configured with all outputs which would result in 3W of power dissipation. This would redisabled and in a high impedance state. The RST pin prosult in a 66C temperature rise. The QFP package thermal grams all the registers with input address 0 and all the outputs performance can be significantly enhanced with an external are turned off. In this configuration the device draws only 40 heat sink and by providing for moving air ventilation. Also, be mA. The reset pin can be used as a shutdown function to resure to calculate the increase in ambient temperature from all duce power consumption. The other special control pin is the devices operating in the system case. Because of the high broadcast (BCST) pin. The BCST pin is also active high and power output of this device, thermal management should be sets all the outputs to the on state connected to input 0. Both considered very early in the design process. Generous pasof these pins are level sensitive and require no clock signal. sive venting and vertical board orientation may avoid the need The two special control pins overwrite the contents of the for fan cooling provided a large heat sink is used. Also, the configuration register. LMH6584/LMH6585 can be operated with a 3.3V power THERMAL MANAGEMENT supply. This will cut power dissipation substantially while only reducing bandwidth by about 10% (2 VPP output). The The LMH6584/LMH6585 are high performance device that LMH6584/LMH6585 are fully characterized and factory tested produces a significant amount of heat. With a 5V supply, the at the 3.3V power supply condition for applications where LMH6584/LMH6585 will dissipate approximately 2W of idling reduced power is desired. power with all outputs enabled. Idling power is calculated based on the typical supply current of 200 mA and a 10V The recommended heat sink is AAVD/Thermalloy part # supply voltage. This power dissipation will vary within the 375024B60024G. This heat sink is designed to be used with range of 1.8W to 2.2W due to process variations. In addition, solder anchors #125700D00000G. This heat sink is larger each equivalent video load (150) connected to the outputs then the LMH6584/LMH6585 package in order to provide 21 www.national.com LMH6584/LMH6585 the first chip (invalid data). When a full 96 bits have been clocked into the first chip the next clock cycle begins moving the first frame of the new configuration data into the second chip. With a full 192 clock cycles both chips have valid data and the Chip Select pin of both chips should be brought high to prevent the data from overshooting. A configure pulse will activate the new configuration on both chips simultaneously, or each chip can be configured separately. The mode, Chip Select, configure, and clock pins of both chips can be tied together and driven from the same sources. DAISY CHAIN OPTION IN SERIAL MODE The LMH6584/LMH6585 support daisy chaining of the serial data stream between multiple chips. This feature is available only in the Serial Programming Mode. To use this feature serial data is clocked into the first chip DIN pin, and the next chip DIN pin is connected to the DOUT pin of the first chip. Both chips may share a Chip Select signal, or the second chip can be enabled separately. When the Chip Select pin goes low on both chips a double length word is clocked into the first chip. As the first word is clocking into the first chip, the second chip is receiving the data that was originally in the shift register of LMH6584/LMH6585 maximum heat dissipation, a smaller heat sink can be selected if forced air circulation will be used. With natural convection the heat sink will reduce the JA from 22C/W to approximately 11C/W. Using a fan will increase the effectiveness of the heat sink considerably by reducing JA to approximately 5C/W. When doing thermal design it is important to note that everything from board layout to case material and case venting will impact the actual JA of the total system. The JA specified in the datasheet is for a typical board layout with external case enclosing the board. PRINTED CIRCUIT LAYOUT The LMH6584/ LMH6585 crosspoint switches are offered in a layout friendly LQFP package. With leads around the device periphery it is easier to place termination resistors and decoupling capacitors close to the device leads. Keeping power and signal traces short is crucial to high frequency performance. Generally, a good high frequency layout will keep power supply and ground traces away from the input and output pins. Parasitic capacitances on these nodes to ground will cause frequency response peaking and possible circuit oscillations (see Application Note OA-15 for more information). If digital control lines must cross analog signal lines (particularly inputs) it is best if they cross perpendicularly. National Semiconductor suggests the following evaluation boards as a guide for high frequency layout and as an aid in device testing and characterization National Semiconductor offers an evaluation board which can be found on the LMH6584 and LMH6585 Product Folder. 30045053 FIGURE 14. Maximum Dissipation vs. Ambient Temperature www.national.com 22 LMH6584/LMH6585 Physical Dimensions inches (millimeters) unless otherwise noted 144-Pin LQFP NS Package Number VNG144C 23 www.national.com LMH6584/LMH6585 32x16 400 MHz Analog Crosspoint Switches, Gain of 1, Gain of 2 Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated