E M C C o m p o n e n t s May 2018 Chip beads For general signal line MMZ series MMZ1005 type MMZ1005 1005[0402 inch]* * Dimensions Code JIS[EIA] (2/11) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20180521 / beads_commercial_signal_mmz1005_en.fm (3/11) E M C C o m p o n e n t s Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Chip beads For general signal line Overview of MMZ1005 type FEATURES Noise reduction solution for general signal line. Various frequency characteristics with 8 materials of different features for countermeasures against everything from general signals to high-speed signals. APPLICATION Noise removal for mobile devices such as smartphones and tablet terminals, and various modules. Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment. PART NUMBER CONSTRUCTION MMZ Series name 1005 LxWxT dimensions (mm) 1005 1.0x0.5x0.5 S Material name B D F S Y 800 C Impedance () at 100MHz 800 80 121 120 Characteristic type C T 000 Packaging style Internal code T Taping 000 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Operating Storage temperature temperature C C MMZ1005 -55 to +125 -55 to +125 The Storage temperature range is for after the circuit board is mounted. Package quantity Individual weight (pieces/reel) 10,000 mg 1 Type RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005_en.fm (4/11) E M C C o m p o n e n t s MMZ1005 type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 30 to 60s Peak Temp. T4 250 to 260C Time t3 10s Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005_en.fm (5/11) E M C C o m p o n e n t s MMZ1005 type MATERIAL CHARACTERISTICS B material: This type is perfectly suited for fast digital signals. By equalizing R components and X components that beads possess at a frequency of 5MHz, it is able to suppress overshooting, undershooting and ringing of fast digital signals. S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz. Y material: High frequency range type intended for the 100MHz region and above. For signal line applications in which the signal frequency is far from the cutoff frequency. Impedance values selected for effectiveness at 80 to 400MHz. D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies. Designed for high impedance at high frequencies (300MHz to 1GHz) for signal line applications. F material: This new product inherits the characteristic of our D-material, namely its sharp impedance rise time, and its impedance peak frequency has been shifted higher into range. The product offers excellent noise suppression from 600MHz to as high as in the GHz range. TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS 2000 D 1800 Impedance() 1600 Y 1400 1200 1000 S 800 F 600 400 B 200 0 10 100 Frequency(MHz) 1000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005_en.fm (6/11) E M C C o m p o n e n t s MMZ1005 type SHAPE & DIMENSIONS 0.50.05 0.50.05 10.05 0.1min. Dimensions in mm 0.5 RECOMMENDED LAND PATTERN 0.5 0.4 0.5 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005_en.fm (7/11) E M C C o m p o n e n t s MMZ1005 type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] ( ) 80 120 600 80 120 240 600 1000 40 80 120 240 300 470 600 1000 1500 1800 10 22 33 68 120 240 33 47 56 Tolerance 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 5 25% 25% 25% 25% 25% 25% 25% 25% DC resistance Rated current Part No. ( )max. 0.19 0.25 0.85 0.12 0.22 0.28 0.52 0.75 0.10 0.17 0.18 0.26 0.38 0.47 0.54 0.70 1.00 0.85 0.10 0.17 0.24 0.38 0.60 0.90 0.50 0.60 0.70 (mA)max. 450 400 200 500 500 400 300 200 550 450 400 300 250 250 250 200 100 150 500 400 400 400 350 200 200 100 100 MMZ1005B800CT000 MMZ1005B121CT000 MMZ1005B601CT000 MMZ1005S800CT000 MMZ1005S121CT000 MMZ1005S241CT000 MMZ1005S601CT000 MMZ1005S102CT000 MMZ1005Y400CT000 MMZ1005Y800CT000 MMZ1005Y121CT000 MMZ1005Y241CT000 MMZ1005Y301CT000 MMZ1005Y471CT000 MMZ1005Y601CT000 MMZ1005Y102CT000 MMZ1005Y152CT000 MMZ1005Y182CT000 MMZ1005D100CT000 MMZ1005D220CT000 MMZ1005D330CT000 MMZ1005D680CT000 MMZ1005D121CT000 MMZ1005D241CT000 MMZ1005F330CT000 MMZ1005F470CT000 MMZ1005F560CT000 Measurement equipment Measurement item Product No. Impedance E4991A+16192A DC resistance Type-7556 Equivalent measurement equipment may be used. Manufacturer Keysight Technologies Yokogawa Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005_en.fm (8/11) E M C C o m p o n e n t s MMZ1005 type ELECTRICAL CHARACTERISTICS Z VS. FREQUENCY CHARACTERISTICS (BY SERIES) MMZ1005B series MMZ1005S series 800 MMZ1005Y series 1400 700 2200 1200 1800 MMZ1005Y152C MMZ1005B601C MMZ1005S601C 400 300 Impedance () 500 MMZ1005S241C 800 MMZ1005S121C MMZ1005S800C 600 MMZ1005B121C 1 10 100 1000 Frequency (MHz) MMZ1005Y471C 1200 MMZ1005Y301C MMZ1005Y241C MMZ1005Y121C 800 MMZ1005Y800C 1000 200 MMZ1005B800C 0 1400 400 200 100 MMZ1005Y601C 600 MMZ1005Y400C 400 200 MMZ1005Y102C 1600 1000 Impedance () Impedance () 600 MMZ1005Y182C 2000 MMZ1005S102C 0 10000 MMZ1005D series 1 10 100 1000 Frequency (MHz) 10000 0 1 10 100 1000 Frequency (MHz) 10000 MMZ1005F series 3000 1200 2500 1000 MMZ1005F560C 2000 Impedance () Impedance () MMZ1005D241C MMZ1005D121C 1500 MMZ1005D680C MMZ1005D330C 1000 800 600 MMZ1005F470C 400 MMZ1005D220C 500 0 0 1 10 100 1000 Frequency (MHz) MMZ1005F330C 200 MMZ1005D100C 10000 1 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005_en.fm (9/11) E M C C o m p o n e n t s MMZ1005 type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ1005B800CT000 MMZ1005B121CT000 Impedance () 80 R Z 60 40 X 20 1 10 100 1000 Frequency (MHz) 10000 MMZ1005S800CT000 R X 100 1000 Frequency (MHz) 10000 1 10 100 1000 Frequency (MHz) 10000 900 800 700 600 500 400 300 200 100 0 R X 10 R 100 50 X 10 100 1000 Frequency (MHz) 10000 MMZ1005S102CT000 Z 1 Z 150 1 100 1000 Frequency (MHz) 10000 1400 1200 1000 800 600 400 200 0 R 400 350 300 250 200 150 100 50 0 80 70 60 50 40 30 20 10 0 X 10 100 1000 Frequency (MHz) 10000 MMZ1005Y121CT000 X 1 10 100 1000 Frequency (MHz) 10000 MMZ1005Y301CT000 400 Impedance () 500 Z 300 200 0 X R 1 10 Z 150 R 100 50 1 10 100 Frequency (MHz) X 1000 1000 100 Frequency (MHz) 10000 10 100 1000 Frequency (MHz) 10000 R Z X 1 10 100 1000 Frequency (MHz) 10000 Z R X 1 10 100 1000 Frequency (MHz) 10000 800 700 600 500 400 300 200 100 0 400 Z 300 R 200 100 X 0 10000 MMZ1005Y471CT000 600 100 200 0 X 500 Impedance () Impedance () R R MMZ1005Y241CT000 250 Z Z MMZ1005Y400CT000 Z 1 800 700 600 500 400 300 200 100 0 1 MMZ1005S241CT000 200 0 Impedance () Impedance () Impedance () 10 Impedance () Z MMZ1005Y800CT000 Impedance () 1 250 MMZ1005S601CT000 160 140 120 100 80 60 40 20 0 X MMZ1005S121CT000 Impedance () Impedance () 160 140 120 100 80 60 40 20 0 R Z Impedance () 0 180 160 140 120 100 80 60 40 20 0 1 10 100 1000 Frequency (MHz) 10000 MMZ1005Y601CT000 1200 1000 Impedance () Impedance () 100 Impedance () 120 MMZ1005B601CT000 Z R X 1 10 100 1000 Frequency (MHz) 10000 800 Z 600 R 400 200 0 X 1 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005_en.fm (10/11) E M C C o m p o n e n t s MMZ1005 type ELECTRICAL CHARACTERISTICS Z R X 1 10 100 1000 Frequency (MHz) 10000 10 100 1000 Frequency (MHz) 10000 R X Z 100 R 100 1000 Frequency (MHz) 10000 50 Z 300 R 200 100 0 10 100 1000 Frequency (MHz) 50 X 10 100 1000 Frequency (MHz) R 10000 0 10000 1 600 400 Z 200 1 1000 900 800 700 600 500 400 300 200 100 0 10 X 100 1000 Frequency (MHz) 10000 MMZ1005D241CT000 X 10 100 1000 Frequency (MHz) R 10000 MMZ1005F470CT000 Z 1 100 1000 Frequency (MHz) 2000 1500 1000 Z R 500 0 X 1 10 100 1000 Frequency (MHz) 10000 MMZ1005F560CT000 1200 1000 Impedance () MMZ1005F330CT000 700 600 500 400 300 200 100 0 10 2500 0 10000 R 100 800 10000 100 1000 Frequency (MHz) Z 3000 X 1 10 150 1000 Impedance () 400 1 MMZ1005D121CT000 500 X 200 Impedance () 10 R 250 X 1 Z 300 150 0 2200 2000 1800 1600 1400 1200 1000 800 600 400 200 0 1 MMZ1005D330CT000 Impedance () Z 600 Impedance () X 200 MMZ1005D680CT000 Impedance () R Impedance () 70 60 50 40 30 20 10 0 Z MMZ1005D220CT000 Impedance () Impedance () MMZ1005D100CT000 1800 1600 1400 1200 1000 800 600 400 200 0 1 MMZ1005Y182CT000 Impedance () 1400 1200 1000 800 600 400 200 0 Impedance () Impedance () Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ1005Y102CT000 MMZ1005Y152CT000 Z R 1 10 X 100 1000 Frequency (MHz) 10000 800 600 400 Z 200 0 R 1 X 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005_en.fm (11/11) E M C C o m p o n e n t s MMZ1005 type PACKAGING STYLE REEL DIMENSIONS o60min. 2.00.5 1.0 8.4 +2.0 -0.0 o130.2 o210.8 14.4max. o1802.0 Dimensions in mm 4.00.1 B A 8.00.3 2.00.05 3.50.05 1.5 +0.1 0 1.750.1 TAPE DIMENSIONS P1 K Dimensions in mm Type MMZ1005 160min. Drawing direction A 0.650.1 Taping B 1.150.1 P1 2.00.05 K 0.8max. 200min. 300min. Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005_en.fm