LM5030 LM5030 100V Push-Pull Current Mode PWM Controller Literature Number: SNVS215B LM5030 100V Push-Pull Current Mode PWM Controller General Description Features The LM5030 High Voltage PWM controller contains all of the features needed to implement Push-Pull and Bridge topologies, using current-mode control in a small 10 pin package. This device provides two alternating gate driver outputs. The LM5030 includes a high-voltage start-up regulator that operates over a wide input range of 14V to 100V. Additional features include: error amplifier, precision reference, dual mode current limit, slope compensation, softstart, sync capability and thermal shutdown. This high speed IC has total propagation delays less than 100ns and a 1MHz capable single resistor adjustable oscillator. n n n n n n n n n n n Package: MSOP-10 and thermally enhanced LLP-10 (4mm x 4mm). Internal High Voltage Start-up Regulator Single Resistor Oscillator Setting Synchronizable Error Amplifier Precision Reference Adjustable Softstart Dual Mode Over-Current Protection Slope Compensation Direct Optocoupler Interface 1.5A Peak Gate Drivers Thermal Shutdown Applications n Telecommunication Power Converters n Industrial Power Converters n +42V Automotive Systems Connection Diagram Top View 20058112 10-Lead MSOP, LLP Ordering Information Order Number Package Type NSC Package Drawing Supplies As LM5030MM MSOP-10 MUB10A 1000 Units on Tape and Reel LM5030MMX MSOP-10 MUB10A 3500 Units on Tape and Reel LM5030SD LLP-10 SDC10A 1000 Units on Tape and Reel LM5030SDX LLP-10 SDC10A 4500 Units on Tape and Reel (c) 2005 National Semiconductor Corporation DS200581 www.national.com LM5030 100V Push-Pull Current Mode PWM Controller March 2005 LM5030 Block Diagram 20058101 FIGURE 1. www.national.com 2 LM5030 Pin Description Pin Name Pin Number Description Application Information VIN 1 Source Input Voltage VFB 2 Inverting input to the error amplifier The non-inverting input is internally connected to a 1.25 Volt reference. Input to start-up regulator. Input range 14 to 100 Volts. COMP 3 Output to the error amplifier There is an internal 5K resistor pull-up on this pin. The error amplifier provides an active sink. Vcc 4 Output from the internal high voltage series pass regulator. The regulation setpoint is 7.7 Volts. If an auxiliary winding raises the voltage on this pin above the regulation setpoint the internal series pass regulator will shutdown, reducing the IC power dissipation. OUT1 5 Output of the PWM controller Alternating PWM output gate driver. OUT2 6 Output of the PWM controller Alternating PWM output gate driver. GND 7 Return Ground CS 8 Current sense input Current sense input for current mode control and current limit sensing. Using separate dedicated comparators, if CS exceeds 0.5 Volt the outputs will go into Cycle by Cycle current limit. If CS exceeds 0.625V the outputs will be disabled and a softstart commenced. RT 9 Oscillator timing resistor pin and synchronization input. An external resistor sets the oscillator frequency. This pin will also accept synchronization pulses from an external oscillator. SS 10 Dual purpose Softstart and Shutdown pin A 10A current source and an external capacitor set the softstart timing length. The controller will enter a low power state if the SS pin is pulled below the typical shutdown threshold of 0.45V. LLP DAP SUB Die Substrtae The exposed die attach pad on the LLP package should be connected to a PCB thermal pad at ground potential. For additional information on using National Semiconductor's No Pull Back LLP package, please refer to LLP Application Note AN-1187. 3 www.national.com LM5030 Absolute Maximum Ratings (Note 1) Lead Temperature (Soldering 4 seconds) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN to GND (Survival) 260C Storage Temperature Range -55C to +150C Junction Temperature 150C -0.3V to 100V VCC to GND (Survival) -0.3V to 16V RT to GND (Survival) -0.3V to 5.5V All other pins to GND (Survival) Power Dissipation (Note 2) Operating Ratings Junction Temperature -0.3V to 7V VIN Internally Limited ESD Rating (Note 3) Human Body Model Machine Model -40C to +105C 14V to 90V 2kV 200V Electrical Characteristics Specifications in standard type face are for TJ= +25C and those in boldface type apply over the full operating junction temperature range. Unless otherwise specified: VIN = 48V, VCC = 10V, and RT = 26.7K Symbol Parameter Conditions Min (Note 4) Typ (Note 5) Max (Note 4) 8.0 Units Startup Regulator VCCReg VCC Regulation open ckt 7.4 7.7 VCC Current Limit (Note 2) 10 17 V I-VIN Startup Regulator Leakage (external Vcc Supply) VIN = 90V 150 500 A IIN Shutdown Current SS = 0V, VCC = open 250 350 A mA VCC Supply VCC undervoltage Lockout Voltage Undervoltage Hysteresis ICC Supply Current VccReg - 300mV VccReg 100mV 1.2 1.6 2.1 V 2 3 mA Cload = 0 V Error Amplifier GBW Gain Bandwidth 4 MHz DC Gain 75 dB Input Voltage VFB = COMP COMP Sink Capability VFB = 1.5V COMP= 1V 1.220 1.245 5 13 1.270 V 0.45 0.5 0.55 V 0.575 0.625 0.675 V mA Current Limit CS1 Cycle by Cycle CS Threshold Voltage CS2 Restart CS Threshold Voltage Resets SS capacitor; auto restart ILIM Delay to Output CS step from 0 to 0.6V Time to onset of OUT Transition (90%) Cload = 0 CS Sink Current (clocked) CS = 0.3V 3 30 ns 6 mA Soft Start/Shutdown www.national.com Softstart Current Source 7 10 13 A Softstart to COMP Offset 0.25 0.5 0.75 V Shutdown Threshold 0.2 0.45 0.7 V 4 (Continued) Specifications in standard type face are for TJ= +25C and those in boldface type apply over the full operating junction temperature range. Unless otherwise specified: VIN = 48V, VCC = 10V, and RT = 26.7K Symbol Parameter Conditions Min (Note 4) Typ (Note 5) Max (Note 4) Units Oscillator Frequency1 (RT = 26.7K) 175 200 225 kHz Frequency2 (RT = 8.2K) 510 600 690 kHz 3.2 3.8 V Sync threshold PWM Comparator Delay to Output COMP set to 2V CS stepped 0 to 0.4V, Time to onset of OUT transition low Max Duty Cycle Inferred from deadtime Min Duty Cycle COMP=0V 30 47.5 COMP to PWM Comparator Gain 49 ns 50 % 0 % 0.34 COMP Open Circuit Voltage VFB = 0V 4.3 5.2 6.1 V COMP Short Circuit Current VFB = 0V, COMP=0V 0.6 1.1 1.5 mA Delta increase at PWM Comparator to CS 80 105 130 mV 85 ns Slope Compensation Slope Comp Amplitude Output Section Deadtime Cload = 0, 10% to 10% 135 185 Output High Saturation Iout = 50mA, VCC - VOUT 0.25 0.75 V Output Low Saturation IOUT = 100mA 0.25 0.75 V Rise Time Cload = 1nF 16 ns Fall Time Cload = 1nF 16 ns Thermal Shutdown Tsd Thermal Shutdown Temp. 165 C Thermal Shutdown Hysteresis 15 C Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, JA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperture is calculated using: Where the value of JA for the mini SO-10 (MM) package is 200C/W. Exceeding the maximum allowable dissipation will cause excessive die temperature, and the device will go into thermal shutdown. Note 3: The human body model is a 100pF capacitor discharged through a 1.5k resistor into each pin. The machine model is a 200pF capacitor discharged directly into each pin. The machine model ESD rating for pin 5 and pin 6 is 150V. Note 4: Limits are 100% production tested at 25C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. The limits are used to calculate National's Average Outgoing Quality Level (AOQL). Note 5: Typical numbers represent the most likely parametric norm for 25C operation. 5 www.national.com LM5030 Electrical Characteristics LM5030 Typical Performance Characteristics Unless otherwise specified: TJ = 25C. VCC vs VIN VCC vs ICC (VIN = 48V) 20058105 20058107 Oscillator Frequency vs Temperature RT = 26.7k Oscillator Frequency vs RT 20058108 20058109 Soft Start Current vs Temperature Deadtime vs Temperature 20058110 www.national.com 20058111 6 LM5030 Typical Performance Characteristics Unless otherwise specified: TJ = 25C. (Continued) Feedback Amplifier Gainphase 20058115 Detailed Operating Description Error Amplifier The LM5030 High Voltage PWM controller contains all of the features needed to implement Push-Pull and Bridge topologies, using current-mode control in a small 10 pin package. Features included are, startup regulator, dual mode current limit, dual alternating gate drivers, thermal shutdown, softstart and slope compensation. This high speed IC has total propagation delays < 100nS. The Functional Block Diagram of the LM5030 is shown in Figure 1. The LM5030 is designed for Current-Mode Control converters which require alternating outputs, such as Push-Pull and Half/Full Bridge topologies. The features included in the LM5030 enable all of the advantages of Current-Mode Control, line feed-forward, cycle by cycle current limit and simplified loop compensation. The oscillator ramp is internally buffered and added to the PWM comparator input to provide slope compensation necessary for current mode control at higher duty cycles. An internal high gain error amplifier is provided within the LM5030. The amplifier's non-inverting reference is tied to 1.25V. In non-isolated applications the power converter output is connected to the VFB pin via the voltage setting resistors and loop compensation is connected between the COMP and VFB pins. For most isolated applications the error amplifier function is implemented on the secondary side ground. Since the internal error amplifier is configured as an open drain output it can be disabled by connecting VFB to ground. The internal 5K pull-up resistor, connected between the 5V reference and COMP, can be used as the pull-up for an optocoupler or other isolation device. PWM Comparator The PWM comparator compares the compensated current ramp signal to the loop error voltage from the internal error amplifier (COMP pin). This comparator is optimized for speed in order to achieve minimum discernable duty cycles. The comparator polarity is such that zero Volts on the COMP pin will cause a zero duty cycle. High Voltage Start-Up Regulator The LM5030 contains an internal high voltage startup regulator. The input pin (Vin) can be connected directly to line voltages as high as 100V. The regulator output is internally current limited to 10mA. Upon power up, the regulator is enabled and sources current into an external capacitor connected to the VCC pin. The recommended capacitance range for the VCC regulator is 0.1F to 50F. When the voltage on the VCC pin reaches the regulation point of 7.7V, the controller outputs are enabled. The outputs will remain enabled unless, VCC falls below 6.1V or if the SS/SHUTDOWN pin is pulled to ground or an over temperature condition occurs. In typical applications, an auxiliary transformer winding is diode connected to the VCC pin. This winding raises the VCC voltage greater than 8V, effectively shutting off the internal startup regulator and saving power while reducing the controller dissipation. The external VCC capacitor must be sized such that the self-bias will maintain a VCC voltage greater than 6.1V during the initial start-up. During a fault mode when the converter self bias winding is inactive, external current draw on the VCC line should be limited as to not exceed the maximum power dissipation of the controller. An external start-up or other bias rail can be used instead of the internal start-up regulator by connecting the VCC and the Vin pins and feeding the external bias voltage (8 - 15V) to that node. Current Limit/ Current Sense The LM5030 contains two levels of over-current protection. If the voltage on the current sense comparator exceeds 0.5 Volts the present cycle is terminated (cycle by cycle current limit). If the voltage on the current sense comparator exceeds 0.625 Volts, the controller will terminate the present cycle and discharge the softstart capacitor. A small RC filter, located near the controller, is recommended for the CS pin. An internal MOSFET discharges the current sense filter capacitor at the conclusion of every cycle, to improve dynamic performance. The LM5030 CS and PWM comparators are very fast, and as such will respond to short duration noise pulses. Layout considerations are critical for the current sense filter and sense resistor. The capacitor associated with the CS filter must be placed very close to the device and connected directly to the pins of the IC (CS and RTN). Also if a current sense transformer is used, both leads of the transformer secondary should be routed to the sense resistor, which should also be located close to the IC. If a current sense resistor located in the drive transistor sources is used, for current sense, a low inductance resistor should be chosen. 7 www.national.com LM5030 Current Limit/ Current Sense The RT resistor should be located very close to the device and connected directly to the pins of the IC (RT and GND). (Continued) Slope Compensation In this case all of the noise sensitive low power grounds should be commoned together around the IC and then a single connection should be made to the power ground (sense resistor ground point). The second level threshold is intended to protect the power converter by initiating a low duty cycle hiccup mode when abnormally high, fast rising currents occur. During excessive loading, the first level threshold will always be reached and the output characteristic of the converter will be that of a current source but this sustained current level can cause excessive temperatures in the power train especially the output rectifiers. If the second level threshold is reached, the softstart capacitor will be fully discharged, a retry will commence following the discharge detection. The second level threshold will only be reached when a high dV/dt is present at the current sense pin. The signal must be fast enough to reach the second level threshold before the first threshold detector turns off the driver. This can usually happen for a saturated power inductor or shorted load. Excessive filtering on the CS pin, extremely low value current sense resistor or an inductor that does not saturate with excessive loading may prevent the second level threshold from ever being reached. The PWM comparator compares the current sense signal to the voltage derived from the COMP pin. The COMP voltage is set by either the internal error amplifier or an external error amplifier through an optocoupler. At duty cycles greater than 50% (composite of alternating outputs) current mode control circuits are prone to subharmonic oscillation. By adding an additional ramp signal to the current sense ramp signal this condition can be avoided. The LM5030 integrates this slope compensation by buffering the internal oscillator ramp and summing it internally to the current sense (CS) signal. Additional slope compensation may be added by increasing the source impedance of the current sense signal. Soft Start/ Shutdown The softstart feature allows the converter to gradually reach the initial steady state operating point, thus reducing start-up stresses and surges. An internal 10uA current source and an external capacitor generate a ramping voltage signal which limits the error amplifier output during start-up. In the event of a second level current limit fault, the softstart capacitor will be fully discharged which disables the output drivers. When the fault condition is no longer present, the softstart capacitor is released to ramp and gradually restart the converter. The SS pin can also be used to disable the controller. If the SS pin voltage is pulled down below 0.45V (nominal) the controller will disable the outputs and enter a low power state. Oscillator, Shutdown and Sync Capability The LM5030 oscillator is set by a single external resistor connected between the RT pin and return. To set a desired oscillator frequency the necessary RT resistor can be calculated as: OUT1, OUT2 and Time Delay The LM5030 provides two alternating outputs, OUT1 and OUT2. The internal gate drivers can each sink 1.5A peak each. The maximum duty cycle for each output is inherently limited to less than 50%. The typical deadtime between the falling edge of one gate driver output and the rising edge of the other gate driver output is 135ns. Each output switches at half the oscillator frequency in a Push-Pull configuration. The LM5030 can also be synchronized to an external clock. The external clock must be of higher frequency than the free running frequency set by the RT resistor. The clock signal should be capacitively coupled into the RT pin with a 100pF capacitor. A peak voltage level greater than 3 Volts with respect to ground is required for detection of the sync pulse. The sync pulse width should be set in the 15 to 150nS range by the external components. The RT resistor is always required, whether the oscillator is free running or externally synchronized. The voltage at the RT pin is internally regulated to a nominal 2 Volts. www.national.com Thermal Protection Internal Thermal Shutdown circuitry is provided to protect the integrated circuit in the event the excessive junction temperature. When activated, typically at 165 degrees Celsius, the controller is forced into a low power reset state, disabling the output drivers and the bias regulator. This feature is provided to prevent catastrophic failures from accidental device overheating. 8 Typical Application Circuit Typical Application Circuit, 36V - 75VIN and 3.3V, 10A OUT 20058103 LM5030 9 www.national.com LM5030 ITEM PART NUMBER DESCRIPTION VALUE C 1 C0805C472K5RAC Capacitor, CER, KEMET 4700p, 50V C 2 C0805C103K5RAC Capacitor, CER, KEMET 0.01, 50V C 3 C4532X7S0G686M Capacitor, CER, TDK 68, 4V C 4 T520D337M006AS4350 Capacitor, TANT, KEMET 330, 6.3V C 5 T520D337M006AS4350 Capacitor, TANT, KEMET 330, 6.3V C 6 C4532X7R3A103K Capacitor, CER, TDK 0.01, 1000V C 7 C3216X7R2A104K Capacitor, CER, TDK 0.1, 100V C 8 C4532X7R2A105M Capacitor, CER, TDK 1, 100V C 9 C4532X7R2A105M Capacitor, CER, TDK 1, 100V C 10 C0805C102K1RAC Capacitor, CER, KEMET 1000p, 100V C 11 C1206C223K5RAC Capacitor, CER, KEMET 0.022, 50V C 12 C3216X7R1E105M Capacitor, CER, TDK 1, 25V C 13 C3216COG2J221J Capacitor, CER, TDK 220p, 630V C 14 C3216COG2J221J Capacitor, CER, TDK 220p, 630V C 15 C1206C104K5RAC Capacitor, CER, KEMET 0.1, 50V C 16 C0805C101J1GAC Capacitor, CER, KEMET 100p, 100V C 17 C0805C101J1GAC Capacitor, CER, KEMET 100p, 100V C 18 C3216X7R1H334K Capacitor, CER, TDK 0.33, 50 D 1 MBRB3030CTL Diode, Schottky, ON D 2 CMPD2838-NSA Diode, Signal, Central D 3 CMPD2838-NSA Diode, Signal, Central D 4 CMPD2838-NSA Diode, Signal, Central D 5 CMPD2838-NSA Diode, Signal, Central L 1 MSS6132-103 Input Choke, Coilcraft 10H, 1.5A L 2 A9785-B Output Choke, Coilcraft 7H R 1 CRCW12061R00F Resistor 1 R 2 CRCW12064990F Resistor 499 R 3 CRCW2512101J Resistor 100, 1W R 4 CRCW2512101J Resistor 100, 1W R 5 CRCW12064022F Resistor 40.2K R 6 CRCW120610R0F Resistor 10 R 7 CRCW120610R0F Resistor 10 R 8 CRCW12061002F Resistor 10K R 9 CRCW120623R7F Resistor 23.7 R 10 CRCW12062002F Resistor 20K R 11 CRCW120610R0F Resistor 10 R 12 CRCW12063010F Resistor 301 R 13 CRCW120610R0F Resistor 10 R 14 CRCW12061001F Resistor 1K TX 1 A9784-B POWER XFR, COILCRAFT TX 2 P8208T CURRENT XFR, Pulse U1 1 LM5030 REGULATOR, NATIONAL U2 2 MOCD207M OPTO-COUPLER, QT OPTOELECTRONICS U3 3 LM3411AM5-3.3 REFERENCE, NATIONAL 651-1727010 DUAL TERMINALS, MOUSER X 1 SUD19N20-90 FET, N, 200V, SILICONIX X 2 SUD19N20-90 FET, N, 200V, SILICONIX www.national.com 10 100:1 3 per ASSY LM5030 Physical Dimensions inches (millimeters) unless otherwise noted 10 Lead MSOP Package NS Package Number MUB10A 10 Lead LLP Package NS Package Number SDC10A 11 www.national.com LM5030 100V Push-Pull Current Mode PWM Controller Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated