OPTICAL COMMUNICATIONS RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm SFP Transceiver PLRXPL-VI-S24-22 Key Features * Compliant with industry-wide physical and optical specifications * Lead free and RoHS compliant * Cost-effective SFP solution * Triple-rate FC/Ethernet performance * Enables higher port densities * Enables greater bandwidth * Proven high reliability Applications * High-speed storage area networks - Switch and hub interconnect - Mass storage systems interconnect - Host adapter interconnect * Computer cluster cross-connect * Custom high-speed data pipes * Short-reach Ethernet This lead-free and RoHS-compliant multirate small form factor pluggable (SFP) transceiver provides superior performance for Fibre Channel and Ethernet applications, and is another in our family of products customized for high-speed, short-reach SAN and intra-POP applications. The multirate feature enables its use in a wider range of system applications. It is fully compliant with FC-PI 100-M5/M6-SN-I, 200-M5/M6-SN-I, and 1000BASE-SX specifications. The housing provides improved EMI performance for demanding applications. This transceiver features a highly-reliable 850 nm oxide vertical-cavity surface-emitting laser (VCSEL) coupled to an LC optical connector. Its small size allows for highdensity board designs that, in turn, enable greater total aggregate bandwidth. Highlights * 1 G FC, 2 G FC, and 1 GE triple-rate performance enables flexible system design and configuration * Lead free and RoHS compliant per European Directive 2002/95/EC * Enhanced digital diagnostic feature set allows real-time monitoring of transceiver performance and system stability * Bail mechanism enables superior ergonomics and functionality in all port configurations * Extended voltage and extended temperature * MSA-compliant small form factor footprint * Serial ID allows customer- and vendor-system-specific information to be placed in transceiver * All-metal housing provides superior EMI performance NORTH AMERICA: 800 498-JDSU (5378) worldwide: +800 5378-JDSU WEBSITE: www.jdsu.com RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 2 PLRXPL-VI-S24-22 Features * Uses a highly-reliable, high-speed, 850 nm, oxide VCSEL * Lead free and RoHS compliant * Hot pluggable * Digital diagnostics, SFF-8472 rev 9.5 compliant * Compliant with Fibre Channel 200M5/M6-SN-I and 100-M5/M6-SN-I * Compliant with 1000BASE-SX, IEEE 802.3 * Low nominal power consumption (400 mW) * -40C to 85C operating temperature range * Single +3.3 V power supply * 10% extended operating voltage range * Bit error rate < 1 x 10-12 * Open Collector Transmit disable, loss of signal and transmitter fault functions * CDRH and IEC 60825-1 Class 1 laser eye safe * FCC Class B compliant * ESD Class 2 per MIL-STD 883 2.224 56.50 .470 11.94 .539 13.70 Dimensions in inches [mm] An eye-safe, cost effective serial transceiver, the PLRXPL-VI-S24-22 features a small, low-power, pluggable package that manufacturers can upgrade in the field, adding bandwidth incrementally. The robust mechanical design features a unique all-metal housing that provides superior EMI shielding. RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 3 Section 1 Functional Description The PLRXPL-VI-S24-22 850 nm VCSEL Gigabit transceiver is designed to transmit and receive 8B/10B encoded serial optical data over 50/125 m or 62.5/125 m multimode optical fiber. Transmitter The transmitter converts 8B/10B encoded serial PECL or CML electrical data into serial optical data meeting the requirements of 100-M5/M6-SN-I, 200-M5/ M6-SN-I Fibre Channel specifications and 1000BASE-SX Ethernet. Transmit data lines (TD+ & TD-) are internally AC coupled with 100 differential termination. An open collector compatible Transmit Disable (Tx_Dis) is provided. This pin is internally terminated with a 10 k resistor to VccT. A logic 1 or no connection on this pin will disable the laser from transmitting. A logic 0 on this pin provides normal operation. The transmitter has an internal PIN monitor diode that is used to ensure constant optical power output across supply voltage and temperature variations. An open collector compatible Transmit Fault (TFault) is provided. The Transmit Fault signal must be pulled high on the host board for proper operation. A logic 1 output from this pin indicates that a transmitter fault has occurred, or the part is not fully seated and the transmitter is disabled. A logic 0 on this pin indicates normal operation. Receiver The receiver converts 8B/10B encoded serial optical data into serial PECL/CML electrical data. Receive data lines (RD+ & RD-) are internally AC coupled with 100 differential source impedance, and must be terminated with a 100 differential load. The receiver's bandwidth has been optimized for fully compliant operation at 1.063/1.25/2.125 Gbps line rates without the use of rate select. An open collector compatible Loss of Signal is provided. The LOS must be pulled high on the host board for proper operation. A logic 0 indicates that light has been detected at the input to the receiver. A logic 1 output indicates that insufficient light has been detected for proper operation. Power supply filtering is recommended for both the transmitter and receiver. Filtering should be placed on the host assembly as close to the Vcc pins as possible for optimal performance. Application schematics are shown in Figure 2 on page 5. RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 4 10 k 16 Transmitter power supply 3 Transmitter disable in VCC_TX TX_DIS TOSA 18 Transmitter positive data TD+ Laser driver TX_GND TX_FAULT 100 19 Transmitter negative data TD - 2 Transmitter fault out 1, 17, 20 Transmitter signal ground 5 MOD_DEF(1) Serial ID clock 4 MOD_DEF(2) Serial ID data SCL Management processor EEPROM SDA 6 MOD_DEF(0) 15 Receiver power supply VCC_RX ROSA RX_GND VCC_RX RD - Receiver RX_GND 50 RD + 50 LOS 12 Receiver Negative data out 13 Receiver Positive data out 8 Loss of signal out 7 Rate select 30 k 9, 10, 11, 14 Receiver signal ground Figure 1. Block diagram RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 5 Section 2 Application Schematics Recommended connections to the transceiver are shown below. Vcc R1* 50 Z* = 100 10 k 1 VeeT PECL driver (TX DATA) VeeT 20 Receiver (Tx fault) R2* 50 Open collector driver (Tx disable) 10 k TD+ 18 4 MOD_DEF(2) VccT 16 VccR 15 7 Rate select VeeR 14 L2 1 H 10 k Receiver (Mod_Def(0)) C2 0.1 F C4 0.1 F C5 10 F R3* 50 RD+ 13 Z* = 100 Rate select 9 VeeR RD- 12 10 VeeR VeeR 11 Vcc 10 k PECL receiver (RX DATA) 8 LOS C1 10F 6 MOD_DEF(0) Vcc +3.3V input Vcc L1 1 H C3 0.1F 5 MOD_DEF(1) 10 k VeeT 17 Open collector bidirectional (Mod_Def(1)) 3 Tx disable Vcc 2 Tx fault Open collector bidirectional (Mod_Def(2)) Vcc TD- 19 R4* 50 Receiver (LOS) Notes Power-supply filtering components should be placed as close to the Vcc pins of the host connector as possible for optimal performance. The PECL driver and receiver will require biasing networks. Please consult application notes from suppliers of these components. CML I/O on the PHY are supported. MOD_DEF(2) and MOD_DEF(1) should be bi-directional open collector connections in order to implement serial ID (MOD_DEF[0,1,2]) PLRXPL-VI-S24-22 transceiver. R1 and R2 may be included in the output of the PHY. Check application notes of the IC in use. * Transmission lines should be 100 differential traces. It is recommended that the termination resistor for the PECL receiver (R3 + R4) be placed beyond the input pins of the PECL receiver. Series source termination resistors on the PECL Driver (R1+R2) should be placed as close to the driver output pins as possible. Figure 2. Recommended application schematic RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 6 2.1 Technical Data Technical data related to the transceiver includes: * Section 2.2 Pin Function Definitions * Section 2.3 Absolute Maximum Ratings * Section 2.4 Electrical Characteristics * Section 2.5 Optical Characteristic * Section 2.6 Link Lengths * Section 2.7 Regulatory Compliance * Section 2.8 PCB Layout * Section 2.9 Front Panel Opening * Section 2.10 Module Outline * Section 2.11 Transceiver Belly-to-Belly Mounting 2.2 Pin Function Definitions Figure 3. Transceiver pin descriptions RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 7 Table 1. Transceiver Pin Descriptions Pin Number Symbol Name Description Receiver 8 LOS Loss of signal out (OC) Sufficient optical signal for potential BER < 1 x 10-12 = logic 0 Insufficient optical signal for potential BER < 1 x 10-12 = logic 1 This pin is open collector compatible, and should be pulled up to Host Vcc with a 10 k resistor. These pins should be connected to signal ground on the host board. Light on = Logic 0 output Receiver DATA output is internally AC coupled and series terminated with a 50 resistor. Light on = Logic 1 output Receiver DATA output is internally AC coupled and series terminated with a 50 resistor. This pin should be connected to a filtered +3.3 V power supply on the host board. See Application Schematics for filtering suggestions. This pin has an internal 30K pulldown to ground. The signal level should not change during module operation. 9, 10, 11, 14 12 VeeR RD- Receiver signal ground Receiver negative DATA out (PECL) 13 RD+ Receiver positive DATA out (PECL) 15 VccR Receiver power supply 7 Rate select Rate select (LVTTL) Transmitter 3 TX disable Transmitter disable in (LVTTL) 1, 17, 20 VeeT Transmitter signal ground 2 TX fault Transmitter fault out (OC) 16 VccT Transmitter power supply 18 TD+ Transmitter positive DATA in (PECL) 19 TD- Transmitter negative DATA in (PECL) Module Definition 4, 5, 6 MOD_DEF(0:2) Module definition identifiers Logic 1 input (or no connection) = laser off Logic 0 input = laser on This pin is internally pulled up to VccT with a 10 k resistor. These pins should be connected to signal ground on the host board. Logic 1 output = laser fault (laser off before t_fault) Logic 0 output = normal operation This pin is open collector compatible, and should be pulled up to Host Vcc with a 10 k resistor. This pin should be connected to a filtered +3.3 V power supply on the host board. See Application Schematics for filtering suggestions. Logic 1 input = light on Transmitter DATA inputs are internally AC coupled and terminated with a differential 100 resistor. Logic 0 input = light on Transmitter DATA inputs are internally AC coupled and terminated with a differential 100 resistor. Serial ID with SFF 8472 diagnostics (see section 3.1) Module definition pins should be pulled up to Host Vcc with 10 k resistors. RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 8 2.3 Absolute Maximum Ratings Parameter Symbol Ratings Unit Storage temperature Operating case temperature Power supply voltage Transmitter differential input voltage Relative humidity Tst Tc Vcc VD RH -40 to +95 -40 to +85 0 to +4.0 2.5 5 to 95 C C V VP-P % 2.4 Electrical Characteristics Parameter Symbol Min Typical Max Unit Notes Supply voltage Data rate Operating temperature range Transmitter Supply current Data input voltage swing Data input rise/fall time Vcc 2.97 1.0 -40 3.3 2.125 3.63 2.2 85 V Gbps C BER < 1x10-12 40 800 70 2200 175 mA mVp-p ps 350 ps Tc ICCT VTDp-p Data input rise/fall time 250 60 60 Data input skew Data input deterministic jitter Data input deterministic jitter Data input deterministic jitter Data input total jitter DJ DJ DJ TJ 20 0.12 0.14 0.1 0.25 ps UI UI UI UI Data input total jitter TJ 0.26 UI Data input total jitter TJ 0.24 UI Transmit disable voltage level VIH VIL Vcc -1.0 0 Vcc 0.8 V V Transmit disable/enable assert time TTD TTEN 10 1 s ms Transmit fault output voltage level Transmit fault assert and reset times VOH VOL TFault TReset Vcc 0.5 100 V V s s Initialization time TINI 300 ms Vcc -0.5 0 10 Differential, peak to peak 20% - 80%, differential 2 GBd operation 3 20% - 80%, differential 1 GBd operation 3 K28.5 pattern, T, @1.062 Gbps 1, 5 K28.5 pattern, T, @2.125 Gbps 1, 5 K28.5 pattern, TP1, @1.25 Gbps 1, 5 27-1 pattern, T, BER < 1 x 10-12, @1.062 Gbps 1, 5 27-1 pattern, T, BER < 1 x 10-12, @2.125Gbps 1, 5 27-1 pattern, TP1, BER < 1 x 10-12, @1.25 Gbps 1, 5 Laser output disabled after TTD if input level is VIH; laser output enabled after TTEN if input level is VIL. Laser output disabled after TTD if input level is VIH; laser output enabled after TTEN if input level is VIL. Transmit fault level is VOH and laser output disabled TFault after laser fault. Transmitter fault is VOL and laser output restored TINI after transmitter disable is asserted for TReset, then disabled. After hot plug or Vcc 2.97V. RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 9 2.4 Electrical Characteristics Parameter Symbol (continued) Min Typical Max Unit 85 120 90 mA mVp-p ps ps UI UI UI UI Receiver Supply current Data output voltage swing Data output rise/fall time Data output skew Data output deterministic jitter Data output deterministic jitter Data output deterministic jitter Total jitter DJ DJ DJ TJ 200 50 0.36 0.39 0.46 0.61 Total jitter TJ 0.64 UI Total jitter TJ 0.75 UI Loss of signal voltage level VOH Vcc -0.5 Vcc V VOL 0 0.5 V TLOSA 100 s TLOSD 100 s Loss of signal assert/deassert time ICCR 600 Notes RLOAD = 100 , differential 20% - 80%, differential RLOAD = 100 , differential K28.5 pattern, R, @1.062 Gbps 1, 9 K28.5 pattern, R, @2.125 Gbps 1, 5 K28.5 pattern, TP4, @1.25 Gbps 1, 5 27-1 pattern, R , BER < 1 x 10-12 @1.062 Gbps 1, 5 27-1 pattern, R , BER < 1 x 10-12 @2.125 Gbps 1, 5 27-1 pattern, TP4, BER < 1 x 10-12 @1.25 Gbps 1, 5 LOS output level VOL TLOSD after light input > LOSD 2 LOS output level VOH TLOSA after light input < LOSA 2 LOS output level VOL TLOSD after light input > LOSD 2 LOS output level VOH TLOSA after light input < LOSA 2 RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 10 2.5 Optical Characteristics Parameter Transmitter Wavelength RMS spectral width Average optical power Optical output rise/fall time Optical modulation amplitude Extinction ratio Deterministic jitter Deterministic jitter Deterministic jitter Total jitter Total jitter Total jitter Relative intensity noise (OMA) Receiver Wavelength Maximum input power Sensitivity (OMA) Stressed sensitivity (OMA) SS1.06 Stressed sensitivity (OMA) SS1.25 Stressed sensitivity (OMA) SS2.12 Loss of signal assert/deassert level Low frequency cutoff Symbol Min 830 p PAVG -9.5 trise/fall OMA 200 ER 9 DJ DJ DJ TJ TJ TJ RIN12 OMA Pm S1 S2 ISI = 0.96 dB ISI = 2.18 dB ISI = 2.2 dB ISI = 2.6 dB ISI = 1.26 dB ISI = 2.03 dB LOSD LOSA FC Typical Max Unit 850 0.5 500 860 0.85 -2.5 150 1125 -125 0.21 0.26 0.20 0.43 0.44 0.43 -117 nm nm dBm ps W dB UI UI UI UI UI UI dB/Hz 770 850 860 0 12 31 nm dBm Wp-p 16 49 -21 -17 0.2 0.3 Wp-p Wp-p Wp-p Wp-p Wp-p Wp-p Wp-p dBm dBm MHz 55 67 69 87 96 109 -30 Notes 20% - 80% K28.5 pattern, T, @1.062 Gbps 1, 5 K28.5 pattern, T, @2.125 Gbps 1, 5 K28.5 pattern, TP2, @1.25 Gbps 1, 5 27-1 pattern, T, @1.062 Gbps 1, 5 27-1 pattern, T, @2.125 Gbps 1, 5 27-1 pattern, TP2, @1.25 Gbps 1, 5 2 GHz, 12 dB reflection 1 Gbps operation, maximum is equivalent to -17 dBm @9 dB ER 2 Gbps operation 1.0625 G operation 1.0625 G operation 1.25 G operation 1.25 G operation 2.125 G operation 2.125 G operation Chatter-free operation -3 dB, P<-16 dBm RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 11 2.6 Link Length Data Rate / Standard Fiber Type Modal Bandwidth @850 nm (MHz*km) Distance Range (m) Notes 1.0625 GBd Fibre Channel 100-M5-SN-I 100-M6-SN-I 62.5/125 m MMF 50/125 m MMF 50/125 m MMF 50/125 m MMF 50/125 m MMF 62.5/125 m MMF 50/125 m MMF 50/125 m MMF 50/125 m MMF 50/125 m MMF 62.5/125 m MMF 50/125 m MMF 50/125 m MMF 50/125 m MMF 50/125 m MMF 200 500 900 1500 2000 200 500 900 1500 2000 200 500 900 1500 2000 .5 to 300 .5 to 500 .5 to 630 .5 to 755 .5 to 860 .5 to 275 .5 to 550 .5 to 595 .5 to 740 .5 to 860 .5to 150 .5 to 300 .5 to 350 .5 to 430 .5 to 500 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 1.25 Gbps IEEE 802.3 1000Base-SX 2.125 GBd Fibre Channel 200-M5-SN-I, 200-M6-SN-I Specification notes: 1. UI (Unit Interval): one UI is equal to one bit time. For example, 2.125 Gbps corresponds to a UI of 470.588ps. 2. For LOSA and LOSD definitions see Loss of Signal Assert/Deassert Level in Optical Characteristics. 3. When operating the transceiver at 1.0 - 1.3 GBd only, a slower input rise and fall time is acceptable. If it is planned to operate the module in the 1.0 - 2.12 GBd range, faster input rise and fall times are required. 4. Measured with stressed eye pattern as per FC-PI (Fibre Channel) and 1000BASE-SX using the worst-case specifications. 5. All jitter measurements performed with worst case input jitter according to FC-PI and 1000BASE-SX. 6. Distances, shown in the Link Length table, are the distances specified in the Fibre Channel and Ethernet standards. Link length distances are calculated for worst-case fiber and transceiver characteristics based on the optical and electrical specifications shown in this document using techniques utilized in IEEE 802.3 (Gigabit Ethernet). In the nominal case, longer distances are achievable. RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 12 2.7 Regulatory Compliance The PLRXPL-VI-S24-22 complies with international electromagnetic compatibility (EMC) and international safety requirements and standards (see details in Table 2 below). EMC performance is dependent on the overall system design. Information included herein is intended as a figure of merit for designers to use as a basis for design decisions. The PLRXPL-VI-S24-22 is lead free and RoHS compliant per Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. Table 2. Regulatory Compliance Feature Test Method Performance Component safety UL 60950 UL94-V0 IEC 60950 Directive 2002/95/EC UL File E209897 TUV Report/Certificate (CB scheme) Lead-free and RoHS-compliant Compliant per the Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. CDRH compliant and Class 1 laser safety. Laser eye safety U.S. 21CFR (J) 1040.10 EN 60825 Electromagnetic Compatibility (EMC) CE EU Declaration of Conformity Compliant with European EMC and Safety Standards. Electromagnetic emissions EMC Directive 89/336/EEC Noise frequency range: 30 MHz to 12 GHz. FCC CFR47 Part 15 Good system EMC design practice required IEC/CISPR 22 to achieve Class B margins. AS/NZS CISPR22 EN 55022 ICES-003, Issue 4 VCCI-03 Electromagnetic immunity EMC Directive 89/336/EEC IEC /CISPR/24 EN 55024 ESD immunity EN 61000-4-2 Exceeds requirements. Withstands discharges of: 8 kV contact, 15 kV and 25 kV air. Radiated immunity EN 61000-4-3 Exceeds requirements. Field strength of 10 V/m RMS, from 10 MHz to 1 GHz. No effect on transceiver performance is detectable between these limits. RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 13 2.8 PCB Layout NOTES: 34.50 1. DATUM AND BASIC DIMENSIONS ESTABLISHED BY CUSTOMER. 2X 30 A 2. PADS AND VIAS ARE CHASSIS GROUND 11 PLACES 20 3X 10 1 B CROSS-HATCHED AREA DENOTES COMPONENT AND TRACE KEEPOUT (EXCEPT CHASSIS GROUND) 3. THRU HOLES, PLATING OPTIONAL 2X 7.20 0.850.05 2 (MARKED "S") 0.1 A B 2X 2.50 2X 2.50 11.9 1 14.25 TYP 5. ALL DIMENSIONS ARE IN MILLIMETERS C D 3.68 A 16.25 4. HOLES DENOTED WITH 'A' ARE NOT REQUIRED WITH PICOLIGHT CAGES (6 PLACES) 3X 7.10 11.08 1.70 8.48 A 5.68 8.58 A B A 9.60 11.93 4.80 A A 1.70 2 TYP 2 2 10X 0.1 1.050.05 L A C 9X 0.950.05 3 (MARKED "G") 0.1 L A C 5 26.80 10 3 PLACES THIS AREA DENOTES COMPONENT KEEP-OUT (TRACES ALLOWED) 41.30 42.30 Figure 4. Board layout 10X 5 10X 3.20 G 2X 0.90 G S G G 10.93 10.53 9.60 G 9X 0.8 9X 0.8 G G G G 2X 1.550.05 0.1 L C D ALL DIMENSIONS ARE IN MILLIMETERS Figure 5. Detail layout 20X 0.500.03 0.06 C D 20.05 TYP 0.06 L C D 11.93 RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 14 2.9 Front Panel Opening Figure 6. Front panel detail Figure 7 2.10 Module Outline All dimensions in inches [mm] Figure 7. Module detail December, 2006 05001369 Rev 3 RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 15 2.11 Transceiver Belly-to-Belly Mounting 6X .600.004 4X .640.004 .135 6X .41.00 .074 .042 .138 All dimensions in inches Figure 8. Mounting detail Section 3 Related Information Other information related to transceiver includes: * Section 3.1 Digital Diagnostic Monitoring and Serial ID Operation * Section 3.2 Package and Handling Instructions * Section 3.3 Electrostatic Discharge (ESD) * Section 3.4 Eye Safety 3.1 Digital Diagnostic Monitoring and Serial ID Operation The PLRXPL-VI-S24-22 is equipped with a 2-wire serial EEPROM that is used to store specific information about the type/identification of the transceiver as well as real-time digitized information relating to the transceiver's performance. See Section IV, "Module Definition Interface and Data Field Description" of the SFP-MSA Pin Definitions and Host Board Layout document for memory/address organization of the identification data and the Small Form Factor Committee's document number SFF-8472 Rev 9.5, dated June 1, 2004 for memory/address organization of the digital diagnostic data. The enhanced digital diagnostics feature monitors five key transceiver parameters which are internally calibrated and should be read as absolute values and interpreted as follows: RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 16 Transceiver temperature in degrees Celsius: internally measured. Represented as a 16-bit signed two's complement value in increments of 1/256C from -40 to +125C with LSB equal to 1/256C. Accuracy is 3C over the specified operating temperature and voltage range. Vcc/supply voltage in volts: internally measured. Represented as a 16-bit unsigned integer with the voltage defined as the full 16-bit value (0-65535) with LSB equal to 100 V with a measurement range of 0 to +6.55 V. Accuracy is 3% of nominal value over the specified operating temperature and voltage ranges. TX bias current in A: represented as a 16-bit unsigned integer with current defined as the full 16-bit value (0-65535) with LSB equal to 2 A with a measurement range of 0 - 131 mA. Accuracy is 10% of nominal value over the specified operating temperature and voltage ranges. TX output power in mW: represented as a 16-bit unsigned integer with the power defined as the full 16-bit value (0-65535) with LSB equal to 0.1 W. Accuracy is 2 dB over the specified temperature and voltage ranges over the range of 100 W to 800 W (-10 dBm to -1 dBm). Data is not valid when transmitter is disabled. RX received optical power in mW: represented as average power as a 16-bit unsigned integer with the power defined as the full 16-bit value (0-65535) with LSB equal to 0.1 W. Accuracy over the specified temperature and voltage ranges is 3 dB from 30 W to 1000 W (-15 dBm to 0 dBm). Reading the Data The information is accessed through the MOD_DEF(1), and MOD_DEF(2) connector pins of the module. The specification for this EEPROM (ATMEL AT24CO1A family) contains all the timing and addressing information required for accessing the data. The device address used to read the Serial ID data is 1010000X(A0h), and the address to read the diagnostic data is 1010001X(A2h). Any other device addresses will be ignored. Refer to Table 3, Table 4, and Table 5 for information regarding addresses and data field descriptions. MOD_DEF(0), pin 6 on the transceiver, is connected to Logic 0 (ground) on the transceiver. MOD_DEF(1), pin 5 on the transceiver, is connected to the SCL pin of the EEPROM. MOD_DEF(2), pin 4 on the transceiver, is connected to the SDA pin of the EEPROM. The EEPROM WP pin is internally tied to ground with no external access, allowing write access to the customer-writable field (bytes 128-247 of address 1010001X). Note: address bytes 0-127 are not write protected and may cause diagnostic malfunctions if written over. RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 17 Decoding the Data The information stored in the EEPROM including organization is defined in the SFP-MSA Pin Definitions and Host Board Layout document, dated 3/13/00, Section IV. The digital diagnostic information stored in the EEPROM is defined in the SFP document SFF-8472 draft rev 9.5, dated June 1, 2004. Table 3. Data Field Descriptions 0 Address(1010000X)(A0h) Serial ID information; defined by SFP MSA 95 0 55 95 JDSU-specific information 127 119 127 Alarm and warning limits Reserved for external calibration constants Real-time diagnostic information JDSU-specific information Non-volatile, customerwriteable, field-writeable area Reserved for SFP MSA 247 255 Address(1010001X)(A2h) 255 JDSU-specific information RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 18 Table 4. Serial ID Data and Map Memory AddressValue Comments Address (1010000X)(A0h) 0 03 SFP transceiver 1 04 SFP with serial ID 2 07 LC connector 3-10 0000000120400C05 850 nm, multimode, 1.062/2.125 FC, intermediate distance and 1000Base-SX 11 01 8B10B encoding mechanism 12 15 Nominal bit rate of 2.125 Gbps 13 00 Reserved 14 00 Single mode fiber not supported 00 Single mode fiber not supported 15 16 1E 300 meters of 50/125 m fiber 17 0F 150 meters of 62.5/125 m fiber 18 00 Copper not supported 19 00 Reserved 20-35 JDSU Vendor name (ASCII) 36 00 Reserved 37-39 00019C IEEE company ID (ASCII) 40-55 PLRXPL-VI-S24-22 Part number (ASCII, no hyphens included) 56-59 Rev of part number (ASCII) 60-61 0352 Wavelength of laser in nm; 850 62Reserved 63 Check code; lower 8 bits of sum from byte 0 through 62 64 00 Reserved 65 1A No Rate Select, Tx_Disable, Tx Fault, Loss of Signal implemented 66 00 Bit rate max of 2.2Gbps 67 00 Bit rate min of 1.0 Gbps Serial number (ASCII) 68-83 84-91 Date code (ASCII) 92 68 Diagnostics monitoring type 93 F0 Digital diagnostics 94 2 Compliance SFF-8472 Rev 9.4 95 Check code; lower 8 bits of sum from byte 64 through 94 RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 19 Table 5. Diagnostics Data Map Memory AddressValue Address (1010001X)(A2h) 00-01 02-03 04-05 06-07 08-09 10-11 12-13 14-15 16-17 18-19 20-21 22-23 24-25 26-27 28-29 30-31 32-33 34-35 36-37 38-39 40-55 56-59 60-63 64-67 68-71 72-75 76-77 78-79 80-81 82-83 84-85 86-87 88-89 90-91 92-94 95 96 97 98 99 100 Temp high alarm Temp low alarm Temp high warning Temp low warning Voltage high alarm Voltage low alarm Voltage high warning Voltage low warning Bias high alarm Bias low alarm Bias high warning Bias low warning TX power high alarm TX power low alarm TX power high warning Tx power Low warning RX power high alarm RX power low alarm RX power high warning RX power low warning Reserved RP4 RP3 RP2 RP1 RP0 Islope Ioffset TPslope TPoffset Tslope Toffset Vslope External calibration constant Reserved Checksum Temperature MSB Temperature LSB Vcc MSB Vcc LSB TX bias MSB Comments MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address For future monitoring quantities External calibration constant External calibration constant External calibration constant External calibration constant External calibration constant External calibration constant External calibration constant External calibration constant External calibration constant External calibration constant External calibration constant External calibration constant Refer to SFF-8472 rev 9.5 Reserved Low order 8 bits of sum from 0-94 Internal temperature AD values Internally measured supply voltage AD values TX bias current AD values RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 20 (continued) Table 5. Diagnostics Data Map Memory AddressValue Address (1010001X)(A2h) 101 102 103 104 105 106 107 108 109 110-7 110-6 110-5 110-4 110-3 110-2 110-1 110-0 111 112-119 120-127 128-247 248-255 TX bias LSB TX power MSB TX power LSB RX power MSB RX power LSB Reserved MSB Reserved LSB Reserved MSB Reserved LSB Tx disable state Soft Tx disable control Reserved Rate select state Soft rate select control Tx fault state LOS state Data ready state Reserved Optional alarm and warning flag bits Vendor specific User/customer EEPROM Vendor specific Comments Measured TX output power AD values Measured RX input power AD values For 1st future definition of digitized analog input For 2nd future definition of digitized analog input Digital state of Tx disable pin Writing 1 disables laser, this is OR'd with Tx_Disable pin Digital state Digital state Digital state; 1 until transceiver is ready Reserved Refer to SFF-8472 rev 9.5 Vendor specific Field writeable EEPROM Vendor specific RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver 21 3.2 Package and Handling Instructions Process Plug The PLRXPL-VI-S24-22 is supplied with a dust cover. This plug protects the transceiver's optics during standard manufacturing processes by preventing contamination from air borne particles. Note: it is recommended that the dust cover remain in the transceiver whenever an optical fiber connector is not inserted. Recommended Cleaning and De-greasing Chemicals JDSU recommends the use of methyl, isopropyl, and isobutyl alcohols for cleaning. Do not use halogenated hydrocarbons (for example, trichloroethane, ketones such as acetone, chloroform, ethyl acetate, MEK, methylene chloride, methylene dichloride, phenol, N-methylpyrolldone). Flammability The PLRXPL-VI-S24-22 housing is made of cast zinc and sheet metal. 3.3 Electrostatic Discharge (ESD) Handling Normal ESD precautions are required during the handling of this module. This transceiver is shipped in ESD protective packaging. It should be removed from the packaging and handled only in an ESD-protected environment utilizing standard grounded benches, floor mats, and wrist straps. Test and Operation In most applications, the optical connector will protrude through the system chassis and be subjected to the same ESD environment as the system. Once properly installed in the system, this transceiver should meet and exceed common ESD testing practices and fulfill system ESD requirements. Typical of optical transceivers, this module's receiver contains a highly sensitive optical detector and amplifier which may become temporarily saturated during an ESD strike. This could result in a short burst of bit errors. Such an event might require that the application re-acquire synchronization at the higher layers (for example, a serializer/deserializer chip). 3.4 Eye Safety The PLRXPL-VI-S24-22 is an international Class 1 laser product per IEC 825, and per CDRH, 21 CFR 1040 Laser Safety Requirements. The PLRXPL-VI-S24-22 is an eye safe device when operated within the limits of this specification. Operating this product in a manner inconsistent with intended usage and specification may result in hazardous radiation exposure. RoHS-Compliant 1.063/1.25/2.125 Gbps 850 nm Transceiver Laser Safety The transceiver is certified as a Class 1 laser product per international standard IEC 60825-1:2007 2nd edition and is considered non-hazardous when operated within the limits of this specification. Caution Operating this product in a manner inconsistent with intended usage and specifications may result in hazardous radiation exposure. Use of controls or adjustments or performance of procedures other than these specified in this product datasheet may result in hazardous radiation exposure. Tampering with this laser product or operating this product outside the limits of this specification may be considered an `act of manufacturing' and may require recertification of the modified product. This device complies with 21 CFR 1040.10 except for deviations pursuant to Laser Notice No. 50 dated June 24, 2007. Ordering Information For more information on this or other products and their availability, please contact your local JDSU account manager or JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide or via e-mail at customer.service@jdsu.com. Sample: PLRXPL-VI-S24-22 Part Number PLRXPL-VI-S24-22 Temp. Range -40 to 85C Power Supply Tolerance 10% NORTH AMERICA: 800 498-JDSU (5378) Dual Rate Fiber Channel X worldwide: +800 5378-JDSU 1000Base-SX X Digital Diagnostics X PCI Compliant X WEBSITE: www.jdsu.com Product specifications and descriptions in this document subject to change without notice. (c) 2013 JDS Uniphase Corporation 30149155 504 0613 PLRXPL-VI-S24-22.DS.OC.AE June 2013