ALUMINUM ELECTROLYTIC CAPACITORS LV Chip Type, High Voltage. Long Life. series Chip Type, high voltage and long life. Load life of 10000 hours at +105C Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2011/65/EU). LV LR Long Life Specifications Item Performance Characteristics Category Temperature Range -40 to +105C Rated Voltage Range 160 to 500V Rated Capacitance Range 1.8 to 33F Capacitance Tolerance 20% at 120Hz, 20C Rated voltage (V) - Leakage Current 160 to 450 0.04CV+100(A)max.(1 minute's) 500 0.04CV+200(A)max.(1 minute's) Measurement frequency : 120Hz at 20C 160 0.20 Rated voltage (V) tan (MAX.) Tangent of loss angle (tan ) 200 0.20 250 0.25 400 0.25 500 0.30 450 0.30 Measurement frequency: 120Hz Rated voltage (V) Impedance ratio Z-40C / Z+20C ZT / Z20 (MAX.) Stability at Low Temperature 160 200 250 400 450 500 6 6 10 10 15 15 Capacitance change tan Leakage current Within 30% of the initial capacitance value 300% or less than the intial specified value Less than or equal to the initial specified value Endurance The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 10000 hours at 105C. Shelf Life After storing the capacitors under no load at 105C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250C and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they shall meet the characteristic requirements listed at right when they are removed from the plate. Resistance to soldering heat Chip Type C0.2 Capacitance L1.0 A B C E L H 4 5 6 7 8 9 10 11 12 13 14 Taping code Capacitance tolerance (20%) Configuration Rated capacitance (6.8F) Negative H (mm) Pressure relief vent 8 x 10 10 x 10 2.9 3.2 10.3 8.3 10.3 8.3 3.1 4.5 10 10 0.8 to 1.1 0.8 to 1.1 3 E B0.2 D0.5 A2 6.8 2G LV Lot No. 2 A0.2 Series 1 U L V 2 G 6 R 8 MNL 1 GS A0.2 Voltage(2G : 400V) Type numbering system (Example : 400V 6.8F) Positive Plastic platform 0.3MAX. 0.5MAX. (8 x 10L, 10) D x L Within 10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Black print on the case top. Marking Trade mark Capacitance change tan Leakage current Rated voltage (400V) Series name 10 x 13.5 3.2 10.3 10.3 4.5 13.5 0.8 to 1.1 Type Voltage V 160 200 250 400 450 500 Code 2C 2D 2E 2G 2W 2H Dimensions Cap.(F) 1.8 3.3 3.9 4.7 5.6 6.8 7.5 8.2 10 12 15 18 22 27 33 160 2C V Code 1R8 3R3 3R9 4R7 5R6 6R8 7R5 8R2 100 120 150 180 220 270 330 200 2D 50 Hz 0.80 400 2G 8 x 10 8 x 10 50 10 x 10 65 10 x 13.5 70 8 x 10 50 10 x 10 65 10 x 13.5 70 Frequency coefficient of rated ripple current Frequency Coefficient 250 2E 120 Hz 1.00 300 Hz 1.25 1 kHz 1.40 10 kHz or more 1.60 8 x 10 35 10 x 10 10 x 13.5 50 55 450 2W 35 10 x 10 50 10 x 13.5 55 8 x 10 25 10 x 10 40 10 x 13.5 45 8 x 10 10 x 10 500 2H 10 x 13.5 25 40 45 Rated Case size D x L (mm) ripple Rated ripple current (mArms) at 105C 120Hz Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100D