CAT.8100D
1.8
3.3
3.9
4.7
5.6
6.8
7.5
8.2
10
12
15
18
22
27
33
1R8
3R3
3R9
4R7
5R6
6R8
7R5
8R2
100
120
150
180
220
270
330
8 × 10
10 × 10
10 × 13.5
8 × 10
10 × 10
10 × 13.5
8 × 10
10 × 10
10 × 13.5
8 × 10
10 × 10
10 × 13.5
8 × 10
10 × 10
10 × 13.5
8 × 10
10 × 10
10 × 13.5
50
65
70
50
65
70
35
50
55
35
50
55
25
40
45
25
40
45
2C 2D 2E 2G 2W
160 200 250 400 450
2H
500
V
Code
Cap.(µF)
Rated
ripple
Case size
φD × L (mm)
400
10
450
15
450
0.30
500
0.04CV+200(µA)max.(1 minute's)
160 to 450
0.04CV+100(µA)max.(1 minute's)
ALUMINUM ELECTROLYTIC CAPACITORS
LV series
Chip Type, High Voltage.
Long Life.
Chip Type, high voltage and long life.
Load life of 10000 hours at +105°C
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2011/65/EU).
Measurement frequency : 120Hz at 20°C
Specifications
Category
Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Endurance
Shelf Life
Resistance to soldering
heat
Marking
Performance CharacteristicsItem
–40 to +105°C
160 to 500V
1.8 to 33µF
± 20% at 120Hz, 20°C
Black print on the case top.
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 10000 hours at 105°C.
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C and then performing voltage treatment based on
JIS C 5101-4 clause 4.1 at 20°C, they shall meet the characteristic
requirements listed at right when they are removed from the plate.
Capacitance change
Leakage current
tan δ
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Capacitance change
Leakage current
tan δ
Within ±30% of the initial capacitance value
Less than or equal to the initial specified value
300% or less than the intial specified value
Z–40°C / Z+20°C
Rated voltage (V)
Impedance ratio
ZT / Z20 (MAX.)
200
6
160
6
Measurement frequency: 120Hz
500
15
250
10
Series
Voltage(2G : 400V)
Lot No.
Plastic platform
0.3MAX.
φD±0.5
B±0.2
A±0.2 A±0.2
C±0.2
0.5MAX.
E
H
Positive
Negative
U
1
L
2
V
3
2
4
G
5
6
6
R
7
8
8
M
9
N
10
L
11
1
12
G
13
S
14
Configuration
Taping code
Capacitance tolerance (±20%)
Rated capacitance
(
6.8µF
)
Rated voltage
(
400V
)
Series name
Type
L±1.0
8 × 10
φD × L
A
B
C
E
2.9
8.3
8.3
3.1
10 × 10
3.2
10.3
10.3
4.5
10 × 13.5
3.2
10.3
10.3
4.5
L10 10 13.5
H
0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
(mm)
Trade mark
A2
6.8 2G
LV
Pressure relief vent
Capacitance
Chip Type
(φ8 × 10L, φ10) Type numbering system (Example : 400V 6.8
µ
F)
Frequency coefficient of rated ripple current
Coefficient
Frequency 50 Hz
0.80 1.00 1.25 1.40 1.60
120 Hz 300 Hz 1 kHz
10 kHz or more
Dimensions
Rated ripple current (mArms) at 105°C 120Hz
LV LR
Long Life
Voltage
V 160 200 250 400 450 500
Code 2C 2D 2E 2G 2W 2H
160
0.20
200
0.20
250
0.25
400
0.25
500
0.30
Rated voltage (V)
tan δ (MAX.)
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please refer to page 3 for the minimum order quantity.
Rated voltage (V)
–
