NOTICE OF REVISION (NOR) (See MIL-STD-480 for instructions) This revision described below has been authorized for the document listed. DATE (YYMMDD) Form Approved OMB No. 0704-0188 91-11-06 Public reporting burden for this collection is estimated to average 1 hour per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302, and to the Office of Information and Regulatory Affairs, Office of Management and Budget, Washington, DC 20503. 2. CAGE CODE 1. ORIGINATOR NAME AND ADDRESS Defense Electronics Supply Center Dayton, Ohio 45444-5277 67268 4. CAGE CODE 67268 6. TITLE OF DOCUMENT 7. REVISION LETTER MICROCIRCUIT, DIGITAL, LOW POWER, SINGLE CHANNEL, DRIVER-RECEIVER, HYBRID (Current) A 3. NOR NO. 5962-R034-92 5. DOCUMENT NO. 5962-89592 (New) B 8. ECP NO. 9. CONFIGURATION ITEM (OR SYSTEM) TO WHICH ECP APPLIES ALL 10. DESCRIPTION OF REVISION Sheet 1: Revisions ltr column; add "B" Revisions description column; add "Changes in accordance with NOR 5962-R034-92". Revisions date column; add "91-11-06". Sheet 7: Table I, Add subgroup 5 to the ICC-100 and IEE-100 tests and remove the temperature reference in the conditions block for these tests. 11. THIS SECTION FOR GOVERNMENT USE ONLY a. CHECK ONE eXfEXISTING DOCUMENT SUPPLEMENTED BY THIS NOR MAY BE USED IN MANUFACTURE. e f REVISED DOCUMENT MUST BE RECEIVED BEFORE MANUFACTURER MAY INCORPORATE THIS CHANGE. b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FOR GOVERNMENT DESC-ECT SIGNATURE AND TITLE Greg Lude Branch Chief 12. ACTIVITY ACCOMPLISHING REVISION DESC-ECT DD Form 1695, JUL 88 REVISION COMPLETED (Signature) DATE (YYMMDD) Shelly M. Jenkins 91-11-06 Previous editions are obsolete. e f CUSTODIAN OF MASTER DOCUMENT SHALL MAKE ABOVE REVISION AND FURNISH REVISED DOCUMENT TO: DATE (YYMMDD) 91-11-06 REVISIONS LTR A DESCRIPTION DATE (YR-MO-DA) Add device types 05 and 06. Correct coupling diagram, figure 4. Add common mode input voltage and test circuit. Table I, change ISIH. Editorial changes throughout. APPROVED 91-05-17 W. Heckman REV SHEET REV A A SHEET 15 16 REV STATUS OF SHEETS PMIC N/A STANDARDIZED MILITARY DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A REV A A A A A A A SHEET 1 2 3 4 5 6 7 PREPARED BY Donald R. Osborne 9 A A A A 10 11 12 13 14 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 CHECKED BY RAY MONNIN APPROVED BY MICHAEL A. FRYE DRAWING APPROVAL DATE 20 JUNE 1989 REVISION LEVEL A DESC FORM 193 SEP 87 DISTRIBUTION STATEMENT A. 8 A MICROCIRCUIT, DIGITAL, LOW POWER, SINGLE CHANNEL, DRIVER-RECEIVER, HYBRID SIZE A SHEET CAGE CODE 67268 1 5962-89592 OF 16 * US GOVERNMENT PRINTING OFFICE: 1987--748-129/60912 5962-E093 Approved for public release; distribution is unlimited. 1. SCOPE 1.1 Scope. This drawing describes device requirements for class H hybrid microcircuits to be processed in accordance with MIL-H-38534. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as shown in the following example: 5962-89592 01 X Drawing number Device type (See 1.2.1) Case outline (See 1.2.2) X Lead finish per MIL-H-38534 1.2.1 Device type(s). The device type(s) shall identify the circuit function as follows: Device type Generic number 01 and 03 ARX3407 02 and 04 ARX3404 05 ARX3467 06 ARX3464 Circuit function Single channel, driver-receiver (MIL-STD-1553 A and B) low power, receiver standby high Single channel, driver-receiver (universal transceiver) low power, receiver standby high Single channel, driver-receiver (MIL-STD-1553 A and B) low power, receiver standby low Single channel, driver-receiver (universal transceiver) low power, receiver standby low 1.2.2 Case outline(s). The case outline(s) shall be as designated in appendix C of MIL-M-38510, and as follows: Outline letter X Y Case outline See figure 1 (24-lead, 1.27" x 1.27" x .175"), hybrid package See figure 1 (24-lead, 1.27" x 1.27" x .200"), flat package 1.3 Absolute maximum ratings. Supply voltage: VCC - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - VEE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - +5 V supply - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Logic input voltage range - - - - - - - - - - - - - - - - - - - - - - - Receiver differential input voltage - - - - - - - - - - - - - - - - - - Receiver common mode input voltage range - - - - - - - - - Driver peak output current - - - - - - - - - - - - - - - - - - - - - - Storage temperature range - - - - - - - - - - - - - - - - - - - - - - Lead temperature (soldering, 10 seconds) - - - - - - - - - - - Junction temperature (TJ) - - - - - - - - - - - - - - - - - - - - - - - Power dissipation (PD) total hybrid: 100 percent duty cycle (TC = +25(C): Device types 01, 03, and 05 - - - - - - - - - - - - - - - - - - - Device types 02, 04, and 06 - - - - - - - - - - - - - - - - - - - Standby mode, all devices - - - - - - - - - - - - - - - - - - - - - - - -0.3 V dc to +18 V dc +0.3 V dc to -18 V dc -0.3 V dc to +7 V dc -0.3 V to +5.5 V 40 Vp-p -10 V to +10 V 300 mA -65(C to +150(C +300(C +160(C 3.0 W 3.24 W 1.06 W SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 2 Power dissipation (PD) hottest die: 100 percent duty cycle: Device types 01, 03, and 05 - - - - - - - - - - - - - - - - - - - - Device types 02, 04, and 06 - - - - - - - - - - - - - - - - - - - - Standby mode, all devices - - - - - - - - - - - - - - - - - - - - - - Thermal resistance: Junction-to-case (OJC) hottest die: Device types 01, 02, 05, and 06 - - - - - - - - - - - - - - - - - Device types 03 and 04 - - - - - - - - - - - - - - - - - - - - - - - Case-to-ambient, all devices - - - - - - - - - - - - - - - - - - - - Maximum junction-to-case temperature rise for the hottest die at 100 percent duty cycle: Device types 01 and 05 - - - - - - - - - - - - - - - - - - - - - - - Device types 02 and 06 - - - - - - - - - - - - - - - - - - - - - - Device type 03 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Device type 04 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 484 mW 1/ 2/ 545 mW 2/ 3/ Derates to zero 88(C/W 58(C/W 21(C/W 42.6(C 47.9(C +28(C 31.6(C 1.4 Recommended operating conditions. Supply voltage range: VCC - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - VEE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5 V supply - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Logic input voltage range - - - - - - - - - - - - - - - - - - - - - - - Receiver differential voltage - - - - - - - - - - - - - - - - - - - - - - Receiver common mode voltage range - - - - - - - - - - - - - Driver peak output current: Device types 01, 02, 05, and 06 - - - - - - - - - - - - - - - - - Device types 03 and 04 - - - - - - - - - - - - - - - - - - - - - - - Maximum serial data rate - - - - - - - - - - - - - - - - - - - - - - - Case operating temperature range (TC) - - - - - - - - - - - - - - 1/ 2/ 3/ +11.4 V dc to +15.75 V dc -11.4 V dc to -15.75 V dc +4.5 V dc to +5.5 V dc 0 V to +5.0 V 40 Vp-p -10.0 V to +10.0 V 180 mA 120 mA 1.0 MHz -55(C to +125(C Duty cycle at 1.0 MHz for device types 01 and 05. Derate to 82 percent maximum at TC = +125(C for a maximum junction temperature of +160(C in the hottest die. Duty cycle for device types 03 and 04 needs no derating over the full operating temperature range. Duty cycle at 1.0 MHz for device types 02 and 06. Derate to 73 percent maximum at TC = +125(C for a maximum junction temperature of +160(C in the hottest die. SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 3 2. APPLICABLE DOCUMENTS 2.1 Government specifications and standard. Unless otherwise specified, the following specifications and standard of the issue listed in that issue of the Department of Defense Index of Specifications and Standards specified in the solicitation, form a part of this drawing to the extent specified herein. SPECIFICATIONS MILITARY MIL-M-38510 MIL-H-38534 - Microcircuits, General Specification for. - Hybrid Microcircuits, General Specification for. STANDARD MILITARY MIL-STD-883 - Test Methods and Procedures for Microelectronics. (Copies of the specifications and standard required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing shall take precedence. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-H-38534 and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-H-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-H-38534. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in QML-38534 (see 6.6 herein). 3.6 Manufacturer eligibility. In addition to the general requirements of MIL-H-38534, the manufacturer of the part described herein shall submit for DESC-ECC review and approval electrical test data (variables format) on 22 devices from the initial quality conformance inspection group A lot sample, produced on the certified line, for each device type listed herein. The data should also include a summary of all parameters manually tested, and for those which, if any, are guaranteed. SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 4 TABLE I. Electrical performance characteristics. Test Receiver Receiver strobe Transmitter Symbol Conditions 1/ -55(C < TC < +125(C unless otherwise specified Group A subgroups Limits Min Unit Max Output low voltage VOL IOL = 10 mA 1,2,3 0.5 Output high voltage VOH IOH = -0.4 mA 1,2,3 Differential input voltage level VI Common mode input voltage range VICR 1 MHz sine wave See figure 3 4,5,6 10 Vp-p Differential input impedance ZIN 1 MHz sine wave 4,5,6 10 k Input capacitance CIN 1 MHz sine wave 2/ Threshold voltage VTH Receiver delay tDR Input low voltage VSIL 1,2,3 Input high voltage VSIH 1,2,3 2.0 V Input low current ISIL VSIL = 0.4 V 1,2,3 -0.4 mA Input high current ISIH VSIH = 2.7 V 1,2,3 40 A Strobe delay tDS Turn-on or turn-off, 2/ see figure 4 9,10,11 200 ns Input low voltage VIL 1,2,3 Input high voltage VIH 1,2,3 2.0 V Input low current IIL VIL = 0.4 V 1,2,3 -0.4 mA Input high current IIH VIH = 2.7 V 1,2,3 2.5 4,5,6 3/ 4/ Input zero crossing 2/ to DATA or DATA, see figure 4 V 40 4 4,5,6 V 0.6 9,10,11 Vp-p 6 5 pF 1.05 Vp-p 450 ns 0.7 V 0.7 V 40 A See footnotes at end of table. SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 5 TABLE I. Electrical performance characteristics - Continued. Test Transmitter (continued) Symbol Differential output voltage Differential output noise VO VON Conditions 1/ -55(C < TC < +125(C unless otherwise specified 4/ 35 load 5/ 140 load 4/ Inhibited 35 load 5/ 140 load 6 6 6 1,2,3 ZOUT 1 MHz sine wave (transmitter off) Output capacitance COUT 1 MHz sine wave 2/ Differential output offset voltage VOS 35 f = 2 MHz tR 35 6 load, tF 35 6 load, see figure 4 Transmitter inhibit 6.5 8.5 26 34 10 device types 01, 03, and 05 device types 02, 04, and 06 Vp-p mVp-p 10 4 4,5,6 FILTER see figure 4 Fall time Max 40 4,5,6 6 load 5/ 6/ 1406 load Unit Min 4,5,6 4,5,6 f = 4 MHz Rise time Limits 6 Differential output impedance Receiver filter response Group A subgroups k 6 5 pF -90 +90 mV pk -360 +360 -4.0 dB -13 ns 9,10,11 device types 01, 03, and 05 device types 02, 04, and 06 100 300 220 300 100 300 220 300 Transmitter delay tDT Transmitter-in to 2/ transmitter-out, see figure 4 550 Input low voltage VIIL 1,2,3 Input high voltage VIIH 1,2,3 2.0 V Input low current IIIL VSIL = 0.4 V 1,2,3 -0.4 mA Input high current IIIH VSIH = 2.7 V 1,2,3 40 A Transmitter inhibit delay (high) tDI-H 0-1 inhibited output, 2/ see figure 4 9,10,11 450 ns 0.7 V See footnotes at end of table. SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55(C < TC < +125(C unless otherwise specified Group A subgroups Limits Min Unit Max Transmitter inhibit Transmitter inhibit delay (low) tDI-L 1-0 active output, 2/ see figure 4 9,10,11 450 ns Power supply +Supply (VCC) -Supply (VEE) +5 V supply ICC-SB IEE-SB ICC1-SB Standby mode 1,2,3 20 35 35 mA +Supply (VCC) -Supply (VEE) ICC-50 IEE-50 50% duty cycle 4,5,6 75 92.5 +Supply (VCC) ICC-100 100% duty cycle -55(C < TC < +25(C 4,6 130 4,5,6 130 4,6 150 4,5,6 150 -Supply (VEE) IEE-100 -55(C < TC < +25(C device types 01, 02, 05, and 06 device types 03 and 04 device types 01, 02, 05, and 06 device types 03 and 04 1/ (+14.9 < VCC < +15.1 V dc), (-14.9 < VEE < -15.1 V dc), (+4.9 < +5 V supply < +5.1 V dc). 2/ Parameter shall be tested as part of initial characterization and after design and process changes. Parameters shall be guaranteed to limits specified in table I for all lots not specifically tested. 3/ Threshold determined by absence of output on receiver (i.e., full rejection). 4/ Measured at point AA' of figure 5. 5/ Measured at point BB' of figure 5. 6/ Offset is measured 2.5 s after the mid-bit zero crossing of the last parity bit of a 660 s transmission cycle of contiguous words (no dead time in between words). SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 7 FIGURE 1. Case outlines. SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 8 NOTES (for case X and case Y): 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance for three place decimals shall be .005 (0.13 mm). FIGURE 1. Case outlines - Continued. SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 9 Device types 01, 02, 03, 04, 05, and 06. Pin Function Pin Function 1 TX DATA OUT 13 +15 V 2 TX DATA OUT 14 NC 3 TX GND 15 RX DATA IN 4 +15 V 16 RX DATA IN 5 NC 17 GND 6 NC 18 CASE GND 7 RX DATA OUT 19 -15 V 8 RX STROBE 20 +5 V 9 RX GND 21 TX INHIBIT 10 RX DATA OUT 22 TX DATA IN 11 NC 23 TX DATA IN 12 NC 24 -15 V FIGURE 2. Terminal connections. SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 10 FIGURE 3. Test circuit. SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 11 Device types 01, 02, 03, and 04. FIGURE 4. Timing waveforms. SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 12 Device types 05 and 06. FIGURE 4. Timing waveforms - Continued. SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 13 FIGURE 5. Coupling diagram. SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 14 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in QML-38534 (see 6.6 herein). The certificate of compliance submitted to DESC-ECC prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-H-38534 and the requirements herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-H-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-H-38534. 4.2 Screening. Screening shall be in accordance with MIL-H-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D using the circuit submitted with the certificate of compliance (see 3.7 herein). (2) TA as specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with MIL-H-38534 and as specified herein. 4.3.1 Group A inspection. Group A inspection shall be in accordance with MIL-H-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 7 and 8 shall be omitted. 4.3.2 Group B inspection. Group B inspection shall be in accordance with MIL-H-38534. 4.3.3 Group C inspection. Group C inspection shall be in accordance with MIL-H-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D using the circuit submitted with the certificate of compliance (see 3.7 herein). (2) TA as specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 4.3.4 Group D inspection. Group D inspection shall be in accordance with MIL-H-38534. SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 15 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (per method 5008, group A test table) Interim electrical parameters 1 Final electrical test parameters 1*,2,3,4,5,6,9, 10,11 Group A test requirements 1,2,3,4,5,6,9, 10,11 Group C end-point electrical parameters 1,2,3 * PDA applies to subgroup 1. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-H-38534. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for original equipment design applications and logistic support of existing equipment. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished in accordance with MIL-STD-481 using DD Form 1693, Engineering Change Proposal (Short Form). 6.4 Record of users. Military and industrial users shall inform Defense Electronics Supply Center when a system application requires configuration control and the applicable SMD. DESC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DESC-ECC, telephone (513) 296-8527. 6.5 Comments. Comments on this drawing should be directed to DESC-ECC, Dayton, Ohio 45444, or telephone (513) 296-8525. 6.6 Approved sources of supply. Approved sources of supply are listed in QML-38534. Additional sources will be added to QML-38534 as they become available. The vendors listed in QML-38534 have agreed to this drawing and a certificate of compliance (see 3.7 herein) has been submitted to and accepted by DESC-ECC. SIZE STANDARDIZED 5962-89592 A MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A SEP 87 REVISION LEVEL A SHEET 16 STANDARDIZED MILITARY DRAWING SOURCE APPROVAL BULLETIN DATE: 91-05-17 Approved sources of supply for SMD 5962-89592 are listed below for immediate acquisition only and shall be added to QML-38534 during the next revision. QML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DESC-ECC. This bulletin is superseded by the next dated revision of QML-38534. Standardized military drawing PIN Vendor CAGE number 5962-8959201XX 5962-8959201YX 5962-8959202XX 5962-8959202YX 5962-8959203XX 5962-8959203YX 5962-8959204XX 5962-8959204YX 5962-8959205XX 5962-8959205YX 5962-8959206XX 5962-8959206YX 88379 88379 88379 88379 88379 88379 88379 88379 88379 88379 88379 88379 Vendor similar PIN 1/ ARX3407 ARX3407FP ARX3404 ARX3404FP ARX3407-001 ARX3407-001FP ARX3404-001 ARX3404-001FP ARX3467 ARX3467FP ARX3464 ARX3464FP 1/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Vendor CAGE number 88379 Vendor name and address Aeroflex Laboratories, Incorporated 35 South Service Road Plainview, NY 11803 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in this information bulletin.