NOTICE OF REVISION (NOR)
(See M IL-STD-480 for instructions)
This re vision described below ha s be en authorized for the document liste d.
DATE (YYMMDD)
91-11-06
Form Approved
OMB No. 0704-0188
Public reporting burden for this coll ection is estimated to a vera ge 1 hour per response, incl uding the time for review ing i nstruct ions, sea rching
exis ting data sources, gathering and m aintaini ng the data nee ded, and completing and re view ing the collection of infor m ation. Send comments
rega rding this burden es timate or any other a spe ct of this collection of infor mation, incl uding suggestions for reducing this burden, to
Washingt on Headquarters Services, Dire ctorate for Information Ope ra tions and Re ports, 1215 Jefferson Davis Highway, Suite 1204, Arlington,
VA 22202-4302, and to the Of fice of Informa tion a nd Regulatory Affairs, O ffice of M anage ment and Budget, Washington, DC 20503.
1. ORIGINATOR NAME AND ADDRESS
Defense Electronics Supply Center
Dayton, Ohio 45444-5277
2. CAGE CODE
67268
3. NOR NO.
5962-R034-92
4. CAGE CODE
67268
5. DOCUMENT NO.
5962-89592
6. TITLE OF DOCUMENT
MICROCIRCUIT, DIGITAL, LOW POWER, SINGLE CHANNEL, DRIVER-RECEIVER,
HYBRID
7. REVISION LETTER
(Current) A (New) B
8. ECP NO.
9. CONFIGURATI ON ITEM (OR SYSTEM) TO W HICH ECP APPLIES
ALL
10. DESCRIPTIO N OF REVISI ON
Sheet 1: Revisi ons ltr column; add "B"
Revisions descri pti on column; add "Changes in accordance wi th
NOR 5962-R034-92".
Revisions date column; add "91-11-06".
Sheet 7: Table I, Add s ubgroup 5 to the I -100 and I -100 tests and remov e the tem perature reference in the
CC EE
conditions block for the se te sts.
11. THIS SECTION FOR GOVERNMENT USE ONLY
a. CHECK ONE
e
X
f
EXISTING DOCUMENT SUPPLEMENTED
e
f
REVISED DOCUMENT MUST BE
e
f
CUSTODIAN OF MASTER DOCUMENT
BY THIS NOR MAY BE USED IN RECEIVED BEFORE MANUFACTURER SHALL MAKE ABOVE REVISION AND
MANUFACTURE. MAY I NCORPORATE THIS CHANGE. FURNISH REVISED DOCUMENT TO:
b. ACTIVITY AUTHORIZED TO APPROVE
CHANGE FOR GOVERNMENT
DESC-ECT
SIGNATURE AND TITLE
Greg Lude
Branch Chi e f
DATE (YYMMDD)
91-11-06
12. ACTIVITY ACCOMPLISHI NG REVISION
DESC-ECT REVISION COMPLETED (Signature)
Shelly M. Jenkins DATE (YYMMDD)
91-11-06
DD Form 1695, JUL 88 Previous e ditions are obsolete.
REVISIONS
LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
A Add de vice types 05 and 06. Corr ect coupling diagra m , figure 4. Add
common mode input voltage and te st circuit. Table I, change ISIH.
Editoria l changes throughout.
91-05-17 W. Heckman
REV
SHEET
REV A A
SHEET 15 16
REV STATUS
OF SHEETS REV AAAAAAA AAAAA
SHEET 1234567891011121314
PMIC N/A PREPARED BY
Donald R. Osborne DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
STANDARDIZED
MILITARY
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
CHECKED BY
RAY MONNIN
MICROCIRCUIT , DIG ITAL , LO W PO WER, S ING L E
CHANNEL, DRIVER-RECEIVER, HYBRID
APPROVED BY
MICHAEL A. FRYE
DRAWING APPROVAL DATE
20 JUNE 1989 SIZE
ACAGE CODE
67268 5962-89592
REVISION LEVEL
A SHEET 1 OF 16
DESC FORM 193 * US GOVERNMENT PRINTING OFFICE: 1987--748-129/60912
SEP 87 5962-E093
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET 2
DESC FORM 193A
SEP 87
1. SCOPE
1.1 Scope. This draw ing describes device re quireme nts for class H hybrid microcircuits to be processe d in accor dance with
MIL-H-38534.
1.2 Part or Ident ifying Num ber (PIN) . The complete PI N shall be as shown in the foll owing example:
5962-89592 01 X X
Drawing number De vice type Case outline Lead finish per
(See 1.2.1) (See 1.2.2) MIL-H-38534
1.2.1 Device type(s). The device type(s) shal l identi fy the circuit function as foll ows:
Device type Ge neric numbe r Circuit function
01 and 03 ARX3407 Single channel, driver-receiver (MIL-STD-1553 A and B) low power ,
rece iver s tandby high
02 and 04 ARX3404 Single channel, driver-receiver (universal tra nsceiver) low power, receiver
sta ndby high
05 ARX3467 Single channel, driver-receiver (MIL-STD-1553 A and B) low power,
receiver standby low
06 ARX3464 Single channel, driver-receiver (universal transceiver) low power, receiver
sta ndby low
1.2.2 Case outline(s). The ca se outli ne(s) shall be as des ignated in appendix C of MIL-M-38510,
and as follows:
Outline letter Case outline
X Se e figure 1 (24-lead, 1.27" x 1.27" x .175"), hybrid package
Y Se e figure 1 (24-lead, 1.27" x 1.27" x .200"), fla t pa ckage
1.3 Absolute maxim um ra tings .
Supply voltage:
V --------------------------------------- -0.3 V dc to +18 V dc
CC
V --------------------------------------- +0.3 V dc to -18 V dc
EE
+5 V supply --------------------------------- -0.3 V dc to +7 V dc
Logic input voltage ra nge ------------------------ -0.3 V to +5.5 V
Receiver differe ntia l i nput voltage ------------------- 40 Vp-p
Receiver common mode input voltage range ---------- -10 V to +10 V
Driver peak output current ----------------------- ±300 mA
Storage temperature range ----------------------- -65
(
C to +150
(
C
Lead tem perature (soldering, 10 s econds) ------------ +300
(
C
Junction temperature (T) ------------------------ +160
(
C
J
Power dis sipa tion (P ) total hybrid:
D
100 perce nt duty cycle (T = +25
(
C):
C
Device types 01, 03, and 05 -------------------- 3.0 W
Device types 02, 04, and 06 -------------------- 3.24 W
Standby mode, all devi ces ----------------------- 1.06 W
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET 3
DESC FORM 193A
SEP 87
Power dis sipa tion (P ) hotte st die:
D
100 percent duty cycle:
Device types 01, 03, and 05--------------------- 484 mW 1/ 2/
Device types 02, 04, and 06--------------------- 545 mW 2/ 3/
Standby mode, all devi ces ----------------------- Derates to zero
Thermal resistance:
Junction-to-case (O ) hottest die :
JC
Device types 01, 02, 05, and 06 ------------------ 88
(
C/W
Device types 03 and 04 ------------------------ 58
(
C/W
Case-to-ambient, all devices --------------------- 21
(
C/W
Maximum junction-to-case temperature ris e for the
hottest die at 100 percent duty cycle :
Device types 01 and 05 ------------------------ 42.6
(
C
Device types 02 and 06 ----------------------- 47.9
(
C
Device type 03 ------------------------------ +28
(
C
Device type 04 ------------------------------ 31.6
(
C
1.4 Recommende d operating conditions.
Supply v olta ge range:
V --------------------------------------- +11.4 V dc to +15.75 V dc
CC
V --------------------------------------- -11.4 V dc to -15.75 V dc
EE
5 V supply ---------------------------------- +4.5 V dc to +5.5 V dc
Logic input voltage ra nge ------------------------ 0 V to +5.0 V
Receiver differential voltage ----------------------- 40 Vp-p
Receiver common mode voltage range -------------- -10.0 V to +10.0 V
Driver pe ak output current:
Device types 01, 02, 05, and 06 ------------------ ±180 mA
Device types 03 and 04 ------------------------ ±120 mA
Maximum serial data rate ------------------------ 1.0 MHz
Case operating temperature range (T ) -------------- -55
(
C to +125
(
C
C
1/ Duty cycle at 1.0 MHz for device types 01 and 05. Derate to 82 pe rcent maximum at T = +125
(
C for a maxi mum juncti on
C
temperature of +160
(
C in the hottest di e .
2/ Duty cycle for device type s 03 a nd 04 needs no derating over the full operating tempe rature range.
3/ Duty cycle at 1.0 MHz for device types 02 and 06. Derate to 73 pe rcent maximum at T = +125
(
C for a maxi mum juncti on
C
temperature of +160
(
C in the hottest di e .
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET 4
DESC FORM 193A
SEP 87
2. APPLICABLE DOCUMENTS
2.1 Government specifications and sta ndard. Unless otherwise specified, the following s pecifications and s tandard of the issue
liste d in tha t issue of the Department of Defense Index of Specifications and Standa rds spe cifie d in the solicitation, f orm a part of
this drawing to the extent speci fied herein.
SPECIFICATIONS
MILITARY
MIL-M-38510 - Microcircuits , Ge neral Specifica tion for.
MIL-H-38534 - Hybrid Microcircuits, Ge neral Specifica tion for.
STANDARD
MILITARY
MIL-STD-883 - Test M ethods and Procedures for Microelectronics.
(Copies of the specificat ions and sta ndard required by manuf acturers in conne ction with specific
acquisition functions s hould be obtained f rom t he contracting act ivity or as directed by the
contracting activity.)
2.2 Orde r of precedence . In the event of a conflict between the text of this drawing and the refere nces cited herein, the text of
this drawing shall take precedence.
3. REQUIREMENTS
3.1 Ite m re quireme nts. The indi vidua l i te m requireme nts shall be in accordance with MIL-H-38534
and as specified herein.
3.2 Des ign, cons truction, and physical dimens ions. The des ign, constr uction, and phy sica l
dime nsions s hall be a s s pecified in MIL-H-38534 and herein.
3.2.1 Case outline(s). The ca se outli ne(s) shall be in accordance with 1.2.2 herein.
3.2.2 Terminal conne ctions . The te rminal conne ctions shall be as specified on figure 2.
3.3 Elect rica l per form ance chara cteristics. Unless otherwise specified herein, the electrical performance characteristics are as
specified in table I and sha ll apply ove r the full specified operating tempe ra ture range.
3.4 Electrical test requireme nts. The electrical test requirement s s hall be the s ubgroups spe cified in table II. The electrical tests
for each subgroup are describe d in table I.
3.5 Marking. Marking shall be in accor dance with MIL-H- 38534. The part shall be marked with t he PIN listed in 1.2 herein. In
addition, the manufacturer's PIN ma y a lso be ma rked as listed in QML-38534 (see 6.6 herein).
3.6 Manufacturer eligibility. In addition to t he gene ral requirements of MIL-H-38534, t he manuf acture r of the part described
here in sha ll submit f or DESC-ECC review and approval electrical te st dat a (va riables format) on 22 devices from the initial quality
conforma nce inspection group A lot sam ple, produce d on the certified li ne, for each device type lis ted herein. The data should als o
include a summary of all para m eters m anua lly tested, and for t hose which, if a ny, are guaranteed.
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET 5
DESC FORM 193A
SEP 87
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/
Group A
Limits
Unit
-55
(
C < T < +125
(
C
subgroups
C
unle ss otherwise specified
Min
Max
Receiver
Output low voltage
V
I = 10 mA
1,2,3
0.5
V
OL OL
Output high volta ge
V
I = -0.4 mA
1,2,3
2.5
V
OH OH
Differential
V
4,5,6
40
Vp-p
I
input voltage level
Common mode
V
1 MHz sine wave
4,5,6
10
Vp-p
ICR
input voltage range
See figure 3
Differential
Z
1 MHz sine wave
4,5,6
10
k
6
IN
input impedance
Input capacitance
C
1 MHz sine wave 2/
4
5
pF
IN
Thres hold voltage
V
3/ 4/
4,5,6
0.6
1.05
Vp-p
TH
Receiver delay
t
Input zero crossing 2/
9,10,11
450
ns
DR
to DATA or DATA, see
figure 4
Receiver
Input low voltage
V
1,2,3
0.7
V
SIL
strobe
Input high voltage
V
1,2,3
2.0
V
SIH
Input low current
I
V = 0.4 V
1,2,3
-0.4
mA
SIL SIL
Input high curr ent
I
V = 2.7 V
1,2,3
40
µA
SIH SIH
Strobe dela y
t
Turn-on or turn-off, 2/
9,10,11
200
ns
DS
see figure 4
Transmitter
Input low voltage
V
1,2,3
0.7
V
IL
Input high voltage
V
1,2,3
2.0
V
IH
Input low current
I
V = 0.4 V
1,2,3
-0.4
mA
IL IL
Input high curr ent
I
V = 2.7 V
1,2,3
40
µA
IH IH
See footnot es a t end of table.
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET 6
DESC FORM 193A
SEP 87
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/
Group A
Limits
Unit
-55
(
C < T < +125
(
C
subgroups
C
unle ss otherwise specified
Min
Max
4/
Transmitter
Differential output
V
35
6
load
1,2,3
6.5
8.5
Vp-p
O
(continued)
v ol ta ge
5/
140
6
load
26
34
4/
Differential output
V
Inhibited 35
6
load
4,5,6
10
mVp-p
ON
noise
5/
140
6
load
40
Differential output
Z
1 MHz sine wave
4,5,6
10
k
6
OUT
impe dance
(transmitter off)
Out put capacita nce
C
1 MHz sine wave 2/
4
5
pF
OUT
Differential output
V
35
6
load
4,5,6
-90
+90
mV pk
OS
offset vol ta ge
5/ 6/
140
6
load
-360
+360
Receiver filter
FILTER
f = 2 MHz
4,5,6
-4.0
dB
res ponse
f = 4 MHz
-13
Rise time
t
35
6
load,
device types
ns
R
01, 03, and 05
9,10,11
100
300
see
device types
figure 4
02, 04, and 06
220
300
Fall time
t
35
6
load,
device types
F
01, 03, and 05
100
300
see
device types
figure 4
02, 04, and 06
220
300
Transmitte r del a y
t
Transmitte r-in to 2/
550
DT
transmitter-out, see
figure 4
Transmitter
Input low voltage
V
1,2,3
0.7
V
IIL
inhibit
Input high voltage
V
1,2,3
2.0
V
IIH
Input low current
I
V = 0.4 V
1,2,3
-0.4
mA
IIL SIL
Input high curr ent
I
V = 2.7 V
1,2,3
40
µA
IIH SIH
Trans m itt er inhibit
t
0-1 inhi bited output , 2/
9,10,11
450
ns
DI-H
delay (high)
see figure 4
See footnot es a t end of table.
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET 7
DESC FORM 193A
SEP 87
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/
Group A
Limits
Unit
-55
(
C < T < +125
(
C
subgroups
C
unle ss otherwise specified
Min
Max
Transmitter
Trans m itt er inhibit
t
1-0 active output, 2/
9,10,11
450
ns
DI-L
inhibit
delay (low)
see figure 4
Power supply
+Supply (V )
I -SB
Standby mode
1,2,3
20
mA
CC CC
-Supply (V )
I -SB
35
EE EE
+5 V supply
I-SB
35
CC1
+Supply (V )
I
50% dut y cycle
4,5,6
75
CC CC-50
-Supply (V )
I
92.5
EE EE-50
+Supply (V )
I
100% dut y
CC CC-100
cycle
-55
(
C < T
device types
4,6
130
C
< +25
(
C
01, 02, 05,
and 06
device types
03 and 04
4,5,6
130
-Supply (V )
I
-55
(
C < T
device types
4,6
150
EE EE-100 C
< +25
(
C
01, 02, 05,
and 06
device types
03 and 04
4,5,6
150
1/ (+14.9 < V < +15.1 V dc), (-14.9 < V < -15.1 V dc), (+4.9 < +5 V supply < +5.1 V dc).
CC EE
2/ Pa ram eter shall be t ested a s part of ini tial characterization a nd after design and process changes. Parameters shall be
guaranteed to limits specified in table I for all lots not specifically tested.
3/ Thres hold determined by abs ence of output on rece iver (i.e., full rejection).
4/ Me as ured at poi nt AA' of figure 5.
5/ Me as ured at poi nt BB' of figure 5.
6/ Offs et is measure d 2.5 µs after the m id-bit zero crossing of t he last pa rity bit of a 660 µs transm ission cycle of contiguous
words (no dead time in between words).
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET 8
DESC FORM 193A
SEP 87
FIGURE 1. Case outl ines.
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET 9
DESC FORM 193A
SEP 87
NOTES (for case X and case Y):
1. Dime nsions are in i nches.
2. Me tric equiv alents are given for genera l i nform ation only.
3. Unle ss otherwise specified, toler ance for three place decimals sha ll be .005 (0. 13 m m ).
FIGURE 1. Case outl ines - Continued.
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET10
DESC FORM 193A
SEP 87
Device types 01, 02, 03, 04, 05, and 06 .
Pin
Function
Pin
Function
1
TX DATA OUT
13
+15 V
2
TX DATA OUT
14
NC
3
TX GND
15
RX DATA IN
4
+15 V
16
RX DATA IN
5
NC
17
GND
6
NC
18
CASE GND
7
RX DATA OUT
19
-15 V
8
RX STROBE
20
+5 V
9
RX GND
21
TX INHIBIT
10
RX DATA OUT
22
TX DATA IN
11
NC
23
TX DATA IN
12
NC
24
-15 V
FIGURE 2. Term inal connect ions .
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET11
DESC FORM 193A
SEP 87
FIGURE 3. Test circuit.
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET12
DESC FORM 193A
SEP 87
Device types 01, 02, 03, a nd 04.
FIGURE 4. Timing waveforms.
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET13
DESC FORM 193A
SEP 87
Device types 05 and 06.
FIGURE 4. Timing waveforms - Continued.
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET14
DESC FORM 193A
SEP 87
FIGURE 5. Coupling diagram.
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET15
DESC FORM 193A
SEP 87
3.7 Certificat e of compliance . A certificate of complia nce s hall be r equired from a manufacturer in order to be lis ted as an
approved s ource of supply in QML-38534 (see 6.6 herein). The certificat e of compliance submitted to DESC-ECC prior to listing a s
an approved source of supply shall af firm that the m anufacturer's product meets the requirements of MIL-H-38534 and the
requirements herein.
3.8 Certificat e of conforma nce. A certifica te of conforma nce as re quired in MIL-H-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
4. QUALITY ASSURANCE PROVISIONS
4.1 Sampling and inspection. Sampling and inspe ction procedures shall be in accor dance with MIL-H- 38534.
4.2 Screening. Scree ning shall be in accordance with MIL-H-38534. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D using the circuit s ubmitt ed with the ce rtifica te of compliance (see 3.7 herein).
(2) T a s specified in a ccorda nce with table I of method 1015 of MIL-STD-883.
A
b. Interim and final e lectrical te s t parameters s hal l be as specifi e d in table II herein, except interim electrical parameter tes ts
prior t o burn-in ar e optional at the discre tion of the m anufacturer.
4.3 Quality conform ance inspection. Quality conforma nce ins pect ion shall be in accordance with M IL-H-38534 and as
specified herein.
4.3.1 Group A inspection. Gr oup A inspection sha ll be in accordance with MIL-H-38534 and as follows:
a. Tests shall be as specified in table II herein.
b. Subgroups 7 a nd 8 shall be om itt ed.
4.3.2 Group B inspection. Group B inspection shall be in a ccordance with MIL-H-38534.
4.3.3 Group C inspe ction. Group C inspection shall be in accordance with MIL-H- 38534 and as follows:
a. End-point electrical paramet ers shall be as specified in table II here in.
b. Stea dy-state li fe te st conditions, m ethod 1005 of MIL-STD- 883.
(1) Test condition A, B, C, or D using the circuit s ubmitt ed with the ce rtifica te of compliance (see 3.7 herein).
(2) T a s specified in a ccorda nce with table I of method 1005 of MIL-STD-883.
A
(3) Test dur ation: 1,000 hours, except as permitted by met hod 1005 of MIL-STD-883.
4.3.4 Group D inspe ction. Group D inspection shall be in accor dance with MIL-H- 38534.
STANDARDIZED
MILITARY DRAWING
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
SIZE
A5962-89592
REVISION LEVEL
ASHEET16
DESC FORM 193A
SEP 87
TABLE II. Electrical te s t re quirements.
MIL-STD-883 t est require m ents
Subgroups
(per method
5008, group A
test table )
Interi m electrical parameters
1
Final electrical te st parameters
1*,2,3,4,5,6,9,
10,11
Group A test requireme nts
1,2,3,4,5,6, 9,
10,11
Group C end-point electrical
1,2,3
parameters
* PDA applies to subgroup 1.
5. PACKAGING
5.1 Packa ging requireme nts . The requireme nts for packaging s hall be in a ccordance with MIL-H-38534.
6. NOTES
6.1 Inte nded use . Microcircuits conform ing to this draw ing are inte nded for original equipment design applica tions and logist ic
support of exis ting e quipment.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared
specification or draw ing.
6.3 Configuration control of SMD's. All proposed changes to exi sting SMD's will be coordinated with the users of record for the
individual documents. This coordination will be accomplished in accordance with MIL-STD-481 using DD Form 1693, Engineering
Change Proposal (Short Form).
6.4 Record of users. Military and indust rial users shall inform Defense Elect ronics Supply Center whe n a s ystem application
requires configuration control and the applicable SMD. DESC will maintain a record of users and this list will be used for
coordinat ion and dist ribution of changes to the drawings. Users of drawings covering microelectronics dev ices (FSC 5962) should
contact DESC-ECC, t elephone (513) 296-8527.
6.5 Comm ents. Comments on this drawing should be dire cte d to DESC-ECC, Dayton, O hio 45444, or telephone (513)
296-8525.
6.6 Approved source s of supply. Approve d sources of supply are li sted in QML-38534. Additional sour ces w ill be added to
QML- 38534 as they become available. The vendors listed in QML-38534 hav e a gre ed to this draw ing and a certificate of
compliance (see 3.7 herein) has been submitted to and acce pted by DESC-ECC.
STANDARDIZED MILITARY DRAWING SOURCE APPROVAL BULLETIN
DATE: 91-05-17
Approved sources of supply for SM D 5962-89592 are li sted below for immediate acquis ition only and shall be adde d to QML- 38534
during the nex t revision. QML-38534 w ill be revised to include the addition or deletion of sources. The vendors list ed be low have
agre ed to this drawing and a certificate of complia nce has been subm itt ed to and acce pte d by DESC-ECC. This bulletin is
supersede d by the ne xt dated rev ision of QML- 38534.
Standardiz ed
Vendor
Vendor
military drawing
CAGE
si mi lar
PIN
numbe r
PIN 1/
5962-8959201XX
88379
ARX3407
5962-8959201YX
88379
ARX3407FP
5962-8959202XX
88379
ARX3404
5962-8959202YX
88379
ARX3404FP
5962-8959203XX
88379
ARX3407-001
5962-8959203YX
88379
ARX3407-001FP
5962-8959204XX
88379
ARX3404-001
5962-8959204YX
88379
ARX3404-001FP
5962-8959205XX
88379
ARX3467
5962-8959205YX
88379
ARX3467FP
5962-8959206XX
88379
ARX3464
5962-8959206YX
88379
ARX3464FP
1/ Cauti on. Do not use this number for item a cquisition.
Ite ms acquire d to thi s number may not satis fy the
performance requireme nts of this drawing.
Vendor CAGE Vendor na me
numbe r and address
88379 Aeroflex Laboratories, Incorpor ated
35 South Service Road
Plainview, NY 11803
The infor m ation containe d herein is diss eminated for convenience only and
the Government assumes no liability whatsoever for any inaccuracies in this
information bulletin.
