G4OAC5AMA - OPTO 22 - Datasheet.Live

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • sales@opto22.com

© 2012–2018 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

PAGE 1

DATA SHEET

Form 0252-180912

G4 DIGITAL AC OUTPUT MODULES

Features

4000 volts optical isolation (transient)

Built-in LED status indicator

Logic levels of 5, 15, and 24 VDC

Removable fuse

Current rating: 3 amps at 45° C

UL Motor Load rating: 1.5 amps

Ability to withstand one-cycle surge of 80 amps

Operating temperature: -30 °C to 70 °C

DESCRIPTION

Opto 22’s G4 AC output modules are used to control or switch AC

loads. Each module provides up to 4000 volts of optical isolation

(transient) between field outputs and the control side of the circuit,

and each features zero voltage turn-on and zero current turn-off.

All AC output modules are equivalent to single-pole, single-throw,

normally open contacts (Form A, SPST-NO) except the G4OAC5A5,

which is equivalent to a single-pole, single-throw, normally closed

contact (Form B, SPST-NC).

Each module is equipped with a 4 amp fast-blow fuse. The fuse

breaking capacity is 40 amps at 250 VAC. Current should be limited to

prevent the short circuit current from exceeding the rated breaking

capacity of the fuse.

Typical applications for AC output modules include switching loads

such as AC relays, solenoids, motor starters, heaters, lamps, and

indicators.

The G4OAC5MA and the G4OAC5AMA are special modules featuring a

manual-on/manual-off/automatic switch, ideal for diagnostic testing

of control applications.

Part numbers ending in FM are Factory Mutual approved.

Compatible with Raspberry Pi

The following G4 digital AC output modules can be used with the

Digital I/O Carrier Board for Raspberry Pi® (part number OPTO-P1-40P)

to monitor and control industrial devices with your Raspberry Pi:

•G4OAC5

•G4OAC5A

•G4OAC5A5

•G4OAC5MA

•G4OAC5AMA

G4OAC5A and G4OAC5AMA

Modules

Part Numbers

Part Description

G4OAC5* G4 AC Output 12–140 VAC, 5 VDC Logic

G4OAC5FM G4 AC Output 12–140 VAC, 5 VDC Logic, Fac-

tory Mutual Approved

G4OAC5A* G4 AC Output 24–280 VAC, 5 VDC Logic

G4OAC5AFM G4 AC Output 24–280 VAC, 5 VDC Logic, Fac-

tory Mutual Approved

G4OAC5A5* G4 AC Output 24–280 VAC, 5 VDC Logic NC

G4OAC5A5FM G4 AC Output 24–280 VAC, 5 VDC Logic NC,

Factory Mutual Approved

G4OAC5MA* G4 AC Output 12–140 VAC, 5 VDC Logic With

Manual/Auto Switch

G4OAC5AMA* G4 AC Output 24–280 VAC, 5 VDC Logic With

Manual/Auto Switch

G4OAC15 G4 AC Output 12–140 VAC, 15 VDC Logic

G4OAC15A G4 AC Output 24–280 VAC, 15 VDC Logic

G4OAC24 G4 AC Output 12–140 VAC, 24 VDC Logic

G4OAC24A G4 AC Output 24–280 VAC, 24 VDC Logic

* Compatible with Raspberry Pi

Raspberry Pi® is a trademark of the Raspberry Pi Foundation.

PAGE 2

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • sales@opto22.com

DATA SHEET

Form 0252-180912

SPECIFICATIONS

Units G4OAC5*

G4OAC5FM**

G4OAC5A*

G4OAC5AFM**

G4OAC5A5*

G4OAC5A5FM** G4OAC5MA* G4OAC5AMA*

Nominal line voltage VAC 120 120/240 120/240 120 120/240

Output voltage range VAC 12–140 24–280 24–280 12–140 24–280

Key feature — — — Normally closed Diagnostic

switch

Diagnostic

switch

Current rating:

At 45 °C ambient

At 70 °C ambient

UL Motor Load Rating A 1.5 1.5 1.5 1.5 1.5

Isolation input-to-

output (transient):

1 ms

1 minute

volts 4000

1500

4000

1500

4000

1500

4000

1500

4000

1500

Off-state leakage at

nominal voltage (60 Hz) mARMS 5 1.25/2.5 1.25/2.5 5 1.25/2.5

Nominal logic voltage VDC 5 5 5 5 5

Logic voltage range VDC 4–8 4–8 4–8 4–8 4–8

Logic pickup voltage VDC 4 4 4 4 4

Logic dropout voltage VDC 1 1 1 1 1

Logic input current at

nominal logic voltage mA 12 12 12 12 12

Control resistance

(Rc in schematic) ohms 220 220 220 220 220

One-cycle surge A peak 80 80 80 80 80

Turn-on time @ 60 Hz milliseconds 8.3*** 8.3*** 8.3*** 8.3*** 8.3***

Turn-off time @ 60 Hz milliseconds 8.3**** 8.3**** 8.3**** 8.3**** 8.3****

Peak repetitive voltage VAC 500 500 500 500 500

Minimum load current mA 20 20 20 20 20

Output voltage drop

maximum peak V 1.6 1.6 1.6 1.6 1.6

Operating frequency Hz 25–65 25–65 25–65 25–65 25–65

dV/dT-off-state V/micro-sec

onds 200 200 200 200 200

dV/dT-commutating --

snubbed for

0.5 power

factor load

snubbed for

0.5 power

factor load

snubbed for

0.5 power

factor load

snubbed for

0.5 power

factor load

snubbed for

0.5 power

factor load

Temperature

Operating:

Storage:

°C

-30 to +70

-30 to +85

-30 to +70

-30 to +85

-30 to +70

-30 to +85

-30 to +70

-30 to +85

-30 to +70

-30 to +85

* Compatible with Raspberry Pi

** Part numbers ending in FM are Factory Mutual approved.

*** One-half cycle maximum. Module turns on at the zero volt crossing of the AC sine wave.

**** One-half cycle maximum. Module turns off at the zero current crossing of the AC sine wave.

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • sales@opto22.com

PAGE 3

DATA SHEET

Form 0252-180912

SPECIFICATIONS (CONT.)

Units G4OAC15*** G4OAC15A*** G4OAC24*** G4OAC24A***

Nominal line voltage VAC 120 120/240 120 120/240

Output voltage range VAC 12–140 24–280 12–140 24–280

Key feature — ————

Current rating:

At 45 °C ambient

At 70 °C ambient

UL Motor Load Rating A 1.5 1.5 1.5 1.5

Isolation input-to-output (transient):

1 ms

1 minute

volts 4000

1500

4000

1500

4000

1500

4000

1500

Off-state leakage at nominal volt-

age (60 Hz) mARMS 5 1.25/2.5 5 1.25/2.5

Logic voltage range VDC 10.5–16 10.5–16 19.5–32 19.5–32

Logic pickup voltage VDC 10.5 10.5 19.5 19.5

Logic dropout voltage VDC 1 1 1 1

Logic input current at nominal logic

voltage mA 15 15 18 18

Control resistance

(Rc in schematic) ohms 1 K 1 K 2.2 K 2.2 K

One-cycle surge A peak 80 80 80 80

Turn-on time @ 60 Hz micro-

seconds 8.3* 8.3* 8.3* 8.3*

Turn-off time @ 60 Hz micro-

seconds 8.3** 8.3** 8.3** 8.3**

Peak repetitive voltage VAC 500 500 500 500

Minimum load current mA 20 20 20 20

Output voltage drop maximum peak V 1.6 1.6 1.6 1.6

Operating frequency Hz 25–65 25–65 25–65 25–65

dV/dT-off-state V/micro-

second 200 200 200 200

dV/dT-commutating -- snubbed for 0.5

power factor load

snubbed for 0.5

power factor load

snubbed for 0.5

power factor load

snubbed for 0.5

power factor load

Temperature

Operating:

Storage:

°C

-30 to +70

-30 to +85

-30 to +70

-30 to +85

-30 to +70

-30 to +85

-30 to +70

-30 to +85

* One-half cycle maximum. Module turns on at the zero volt crossing of the AC sine wave.

** One-half cycle maximum. Module turns off at the zero current crossing of the AC sine wave.

*** Not for use with Opto 22 brains.

PAGE 4

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • sales@opto22.com

DATA SHEET

Form 0252-180912

DIMENSIONS

SCHEMATICS

OPTO 22 • www.opto22.com SALES • sales@opto22.com SUPPORT • support@opto22.com

43044 Business Park Dr. Temecula, CA 92590-3614 800-321-6786 • 1-951-695-3000 800-835-6786 • 1-951-695-3080

© 2006–2018 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

More about Opto 22

Form 1335-180323

PRODUCTS

Opto 22 develops and manufactures reliable, easy-to-use, open

standards-based hardware and software products.

Industrial automation, process control, building automation, industrial

refrigeration, remote monitoring, data acquisition, and industrial

internet of things (IIoT) applications worldwide all rely on Opto 22.

groov EPIC® System

Opto 22’s groov Edge Programmable Industrial Controller (EPIC)

system is the culmination of over 40 years of experience in designing

products for the automation industry.

groov EPIC gives you an industrially hardened system with

guaranteed-for-life I/O, a flexible Linux®-based controller with

gateway functions, and software for your IIoT application or any

application.

groov EPIC I/O

I/O provides the local connection to

sensors and equipment. groov I/O

offers up to 24 channels on each I/O

module, with a spring-clamp terminal

strip, integrated wireway, and swing-

away cover.

Opto 22 I/O is so reliable, we can afford

to guarantee it for life. groov I/O is hot

swappable, UL Hazardous Locations

approved, and ATEX compliant.

groov EPIC Controller

The heart of the system is the groov

EPIC controller. It handles a wide range of digital, analog, and serial

functions for data collection, remote monitoring, process control, and

discrete and hybrid manufacturing.

In addition, the EPIC provides secure data communications among

physical assets, control systems, software applications, online services,

and more, both on premises and in the cloud.

Configuring and troubleshooting I/O and networking is easier with

the EPIC’s integrated high-resolution touchscreen. Authorized users

can see your groov View HMI locally on the touchscreen or on a

monitor connected via the HDMI or USB ports.

groov EPIC Software

Software includes:

•Flowchart-based PAC Control for control programming, or build

your own custom application with optional secure shell access

•groov View for building and viewing your own device-

independent HMI

•Node-RED for creating simple logic flows from pre-built nodes

•Ignition Edge® from Inductive Automation®, with OPC-UA drivers

to Allen-Bradley®, Siemens®, and other control systems, and

MQTT/Sparkplug communications for efficient IIoT data transfer

groov Edge Appliance

Visualization, data handling, and connectivity in a

compact, industrial box: that’s the groov Edge

Appliance. Included are:

•groov View for building and viewing operator

interfaces on PCs and mobile

•Node-RED for building simple logic flows

•Ignition Edge® from Inductive Automation®,

for OPC-UA drivers and MQTT/Sparkplug IIoT communications

Older products

From solid state relays (our first products) to world-famous G4 and

SNAP I/O, to SNAP PAC controllers, Opto 22 products last a long time.

You can count on us to give you the reliability and service you expect.

QUALITY

Founded in 1974, Opto 22 has established

a worldwide reputation for high-quality

products. All are made in the U.S.A. at our

manufacturing facility in Temecula,

California.

Because we test each product twice

before it leaves our factory rather than

testing a sample of each batch, we can

guarantee most solid-state relays and

optically isolated I/O modules for life.

FREE PRODUCT SUPPORT

Opto 22’s California-based Product Support Group offers free,

comprehensive technical support for Opto 22 products from

engineers with decades of training and experience. Support is

available in English and Spanish by phone or email, Monday–Friday,

7 a.m. to 5 p.m. PST.

Support is always available on our website, including how-to videos,

user’s guides, the Opto 22 KnowledgeBase, troubleshooting tips, and

OptoForums. In addition, free hands-on training is available at our

Temecula, California headquarters, and you can register online.

PURCHASING OPTO 22 PRODUCTS

Opto 22 products are sold directly and through a worldwide network

of distributors, partners, and system integrators. For more information,

contact Opto 22 headquarters at 800-321-6786 (toll-free in the U.S.

and Canada) or +1-951-695-3000, or visit our website at