PACKAGE DIMENSIONS
13-3
PACKAGE CROSS REFERENCE
PACKAGE OUTLINE DESCRIPTION LTC NSC ADI/PMI MOT TI LINFIN MAXIM
8-Lead Side Brazed (Hermetic) D8 D D — l — — DA
14-, 16-, 18- and 20-Lead D D D YB L — — DD, DE,
Side Brazed (Hermetic) QB DN, DP
XB
20-Lead Plastic TSSOP (4.4mm) F U DL UP,
— PW — UG,
UI
48-, 56-Lead Plastic TSSOP (6.1mm) FW
16-, 20-, 24-, and 28-Lead GN
SSOP (Narrow 0.150)
16-, 20-, 28- and 36-Lead Plastic G MSA RS — DB AP,
Plastic SSOP (5.3mm) AG,
AT
36- and 44-Lead Plastic GW MSA — — DB AX
SSOP (Wide 0.300)
8- or 10-Lead TO-5 Metal Can H H H H G — T TV,
J TW,
KVS
3- or 4-Lead TO-39 Metal Can H H H H G — T TV,
J TW,
KVS
2-, 3- or 4-Lead Standard TO-46 H H H — — T
—
Metal Can or in Thermal Caps
3-Lead TO-52 H SR
Metal Can
8-Lead Ceramic DIP (Hermetic) J8 J Q Z U JG Y JA
J8
14-, 16-, 18-, 20- and 24-Lead J J D Y L J J RD, RN,
Ceramic DIP J14 Q Q J RE, RP
(Narrow 0.300, Hermetic) J16 X
28-Lead Ceramic DIP JW — Q T L JG,
(Wide 0.600, Hermetic) JI
2-Lead TO-3 Metal Can K K — — K — K KQ
Steel
4-Lead TO-3 Metal Can K K — — — KJ K KS
20-Pin Leadless Chip Carrier L E E F FN FN L L
(Rectangular, Hermetic) FK
20-Pin Leadless Chip Carrier LS E E F FN FN L L
(Square 0.350, Hermetic) FK
Proprietary Device Prefixes LT LF LP AD OP MC TL LX MAX
LTC LH MF REF SG
LM CMP
SIDE BRAZED
LCC METAL CAN CERDIP
Ceramic Dual-In-Line METAL CANS SSOP
Shrink Small Outline
TSSOP
Thin Shrink
Small Outline
PACKAGE DIMENSIONS
13-4
PACKAGE OUTLINE DESCRIPTION LTC NSC ADI/PMI MOT TI LINFIN MAXIM
3-Lead Plastic DD Pak M S ————DD —
5-Lead Plastic DD Pak Q S ————DD —
7-Lead Plastic DD Pak R S ————— —
8- and 10-Lead, Ultrasmall MSOP MS8 ————DGK— UA
MS10
8-Lead PDIP, Plastic Dual-In-Line N8 N N P P1 P M P
N8
14-, 16-, 18-, 20- and 24-Lead N N N P P2 N N ND, NE, NN,
PDIP, Plastic Dual-In-Line N14 NE NP, NG
(Narrow 0.300)
28-Lead PDIP, Plastic Dual-In-Line NW — N P P N — PI
(Wide 0.600)
3-Lead Plastic TO-3P P —————— K
(Similar to TO-247)
8-Lead Plastic SO S8 M R SO8 D D — SA
(Narrow 0.150)
14- and 16-Lead Plastic SO S M R SO14 D D — SD
(Narrow 0.150) SO16 SE
16-, 18-, 20-, 24- and 28-Lead SW M R SO16 D D — WE, WN,
Plastic SO (Wide 0.300) SO18 WP, WF
SO20 WG, WI
SO24
SO28
3-Lead Plastic SOT-223 ST MP ————ST UR
Small Outline Transistor
3-Lead SOT-23 S3 M3 RT — — DBV — UR, US
4-Lead SOT-143 S4
5- and 6-Lead SOT-23 S5, S6 M5 RT DBV UT, UK
3- or 5-Lead Plastic TO-220 T T — — T KC P C
T T ———KV P C
7-Lead Plastic TO-220 T7 —————— C
(Formerly Y Package)
10- or 14-Lead Flatpak, Glass Sealed W W L RC F UO10 F FB
(Hermetic)
10- or 14-Lead Flatpak, Metal WB F AH-148 OH-148 — WO10 — M
Sealed, Bottom Brazed LM WO14
(Hermetic)
3-Lead, Plastic TO-92 Package Z Z — — P LP — ZR
Proprietary Device Prefixes LT LF LP AD OP MC TL LX MAX
LTC LH MF REF SG
LM CMP
PACKAGE CROSS REFERENCE
PDIP
Plastic Dual-In-Line MSOP DD PAK
TO-3P
(TO-247)
SO
Small Outline
TO-220
FLATPAK
TO-92
PACKAGE DIMENSIONS
13-5
D8 Package
8-Lead Side Brazed (Hermetic)
(LTC DWG # 05-08-1210)
D Package
14-Lead Side Brazed (Hermetic)
(LTC DWG # 05-08-1210)
D14 1098
0.008 – 0.015
(0.203 – 0.381)
0.300
(7.620)
REF
1
8
27
36
45
0.290
(7.366)
TYP
0.760
(19.304)
MAX
0.005
(0.127)
MIN 910
11
121314
PIN NO. 1
IDENT
0.485
(12.319)
MAX
0.125
(3.175)
MIN
0.020 – 0.060
(0.508 – 1.524)
0.100
(2.54)
BSC
0.165
(4.191)
MAX
0.015 – 0.023
(0.381 – 0.584)
0.054
(1.372)
TYP
D8 1098
1
8
2
7
3
6
4
5
0.290
(7.366)
TYP
0.520
(13.208)
MAX
0.005
(0.127)
MIN
PIN NO. 1
IDENT
0.008 – 0.015
(0.203 – 0.381)
0.300
(7.620)
REF
0.485
(12.319)
MAX
0.100
(2.54)
BSC
0.125
(3.175)
MIN
0.020 – 0.060
(0.508 – 1.524)
0.165
(4.191)
MAX
0.015 – 0.023
(0.381 – 0.584)
0.054
(1.372)
TYP
PACKAGE DIMENSIONS
13-6
D Package
16-Lead Side Brazed (Hermetic)
(LTC DWG # 05-08-1210)
D Package
18-Lead Side Brazed (Hermetic)
(LTC DWG # 05-08-1210)
D16 1098
0.008 – 0.015
(0.203 – 0.381)
0.300
(7.620)
REF
18
27
36
45
0.290
(7.366)
TYP
0.840
(21.336)
MAX
910
11
1213141516
0.005
(0.127)
MIN
PIN NO. 1
IDENT
0.165
(4.191)
MAX
0.100
(2.54)
BSC 0.015 – 0.023
(0.381 – 0.584)
0.054
(1.372)
TYP
0.125
(3.175)
MIN
0.485
(12.319)
MAX
0.020 – 0.060
(0.508 – 1.524)
D18 1098
18
27
36
45
0.910
(23.114)
MAX
0.290
(7.366)
TYP
9
10
11
1213141516
0.005
(0.127)
MIN 17
18
PIN NO. 1
IDENT
0.008 – 0.015
(0.203 – 0.381)
0.300
(7.620)
REF
0.485
(12.319)
MAX
0.020 – 0.060
(0.508 – 1.524)
0.015 – 0.023
(0.381 – 0.584)
0.054
(1.372)
TYP
0.100
(2.54)
BSC
0.125
(3.175)
MIN
0.165
(4.191)
MAX
PACKAGE DIMENSIONS
13-7
D Package
20-Lead Side Brazed (Hermetic)
(LTC DWG # 05-08-1210)
D20 1098
0.008 – 0.015
(0.203 – 0.381)
0.300
(7.620)
REF
18
27
36
45
1.010
(25.654)
MAX
0.290
(7.366)
TYP
910
11
1213141516
0.005
(0.127)
MIN 1718
PIN NO. 1
IDENT
1920
0.020 – 0.060
(0.508 – 1.524)
0.485
(12.319)
MAX
0.015 – 0.023
(0.381 – 0.584)
0.054
(1.372)
TYP
0.100
(2.54)
BSC
0.125
(3.175)
MIN
0.165
(4.191)
MAX
F20 TSSOP 1098
0.09 – 0.18
(0.0035 – 0.0071)
0° – 8°
0.50 – 0.70
(0.020 – 0.028)
4.30 – 4.48**
(0.169 – 0.176)
6.25 – 6.50
(0.246 – 0.256)
134
5
6
7
8910
111214 13
6.40 – 6.60*
(0.252 – 0.260)
20 19 18 17 16 15
1.10
(0.0433)
MAX
0.05 – 0.15
(0.002 – 0.006)
0.65
(0.0256)
BSC 0.18 – 0.30
(0.0071 – 0.0118)
2
NOTE: DIMENSIONS ARE IN MILLIMETERS
DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.152mm (0.006") PER SIDE
DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.254mm (0.010") PER SIDE
*
**
F Package
20-Lead Plastic TSSOP (4.4mm)
(LTC DWG # 05-08-1650)
PACKAGE DIMENSIONS
13-8
FW Package
48-Lead Plastic TSSOP (6.1mm)
(LTC DWG # 05-08-1651)
FW48 TSSOP 1298
0.09 – 0.20
(0.0035 – 0.008)
0° – 8°
0.45 – 0.75
(0.018 – 0.029)
0.17 – 0.27
(0.0067 – 0.0106)
0.50
(0.0197)
6.0 – 6.2**
(0.236 – 0.244)
7.9 – 8.3
(0.311 – 0.327)
134
5
6
7
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
12.4 – 12.6*
(0.488 – 0.496)
1.20
(0.0473)
MAX
0.05 – 0.15
(0.002 – 0.006)
2
48 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 2547
NOTE: DIMENSIONS ARE IN MILLIMETERS
DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.152mm (0.006") PER SIDE
DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.254mm (0.010") PER SIDE
*
**
C0.10
-T-
-C-
FW Package
56-Lead Plastic TSSOP (6.1mm)
(LTC DWG # 05-08-1651)
FW48 TSSOP 1298
0.09 – 0.20
(0.0035 – 0.008)
0° – 8°
0.45 – 0.75
(0.018 – 0.029)
6.0 – 6.2**
(0.236 – 0.244)
7.9 – 8.3
(0.311 – 0.327)
134
5
6
7
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
13.9 – 14.1*
(0.548 – 0.556)
1.20
(0.0473)
MAX
0.05 – 0.15
(0.002 – 0.006)
2
56 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 2955
NOTE: DIMENSIONS ARE IN MILLIMETERS
DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.152mm (0.006") PER SIDE
DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.254mm (0.010") PER SIDE
*
**
C0.10
-T-
-C-
0.17 – 0.27
(0.0067 – 0.0106)
0.50
(0.0197)
PACKAGE DIMENSIONS
13-9
G Package
16-Lead Plastic SSOP (5.3mm)
(LTC DWG # 05-08-1640)
G16 SSOP 1098
0.13 – 0.22
(0.005 – 0.009)
0° – 8°
0.55 – 0.95
(0.022 – 0.037)
5.20 – 5.38**
(0.205 – 0.212)
7.65 – 7.90
(0.301 – 0.311)
12345678
6.07 – 6.33*
(0.239 – 0.249)
14 13 12 11 10 91516
1.73 – 1.99
(0.068 – 0.078)
0.05 – 0.21
(0.002 – 0.008)
0.65
(0.0256)
BSC 0.25 – 0.38
(0.010 – 0.015)
NOTE: DIMENSIONS ARE IN MILLIMETERS
DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.152mm (0.006") PER SIDE
DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.254mm (0.010") PER SIDE
*
**
G20 SSOP 1098
0.13 – 0.22
(0.005 – 0.009)
0° – 8°
0.55 – 0.95
(0.022 – 0.037)
5.20 – 5.38**
(0.205 – 0.212)
7.65 – 7.90
(0.301 – 0.311)
12345678910
7.07 – 7.33*
(0.278 – 0.289)
1718 14 13 12 1115161920
1.73 – 1.99
(0.068 – 0.078)
0.05 – 0.21
(0.002 – 0.008)
0.65
(0.0256)
BSC 0.25 – 0.38
(0.010 – 0.015)
NOTE: DIMENSIONS ARE IN MILLIMETERS
DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.152mm (0.006") PER SIDE
DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.254mm (0.010") PER SIDE
*
**
G Package
20-Lead Plastic SSOP (5.3mm)
(LTC DWG # 05-08-1640)
PACKAGE DIMENSIONS
13-10
G Package
24-Lead Plastic SSOP (5.3mm)
(LTC DWG # 05-08-1640)
G28 SSOP 1098
0.13 – 0.22
(0.005 – 0.009)
0° – 8°
0.55 – 0.95
(0.022 – 0.037)
5.20 – 5.38**
(0.205 – 0.212)
7.65 – 7.90
(0.301 – 0.311)
12345678 9 10 11 12 1413
10.07 – 10.33*
(0.397 – 0.407)
2526 22 21 20 19 18 17 16 1523242728
1.73 – 1.99
(0.068 – 0.078)
0.05 – 0.21
(0.002 – 0.008)
0.65
(0.0256)
BSC 0.25 – 0.38
(0.010 – 0.015)
NOTE: DIMENSIONS ARE IN MILLIMETERS
DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.152mm (0.006") PER SIDE
DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.254mm (0.010") PER SIDE
*
**
G Package
28-Lead Plastic SSOP (5.3mm)
(LTC DWG # 05-08-1640)
G24 SSOP 1098
0.13 – 0.22
(0.005 – 0.009)
0° – 8°
0.55 – 0.95
(0.022 – 0.037)
5.20 – 5.38**
(0.205 – 0.212)
7.65 – 7.90
(0.301 – 0.311)
12345678 9 10 11 12
8.07 – 8.33*
(0.318 – 0.328)
2122 18 17 16 15 14 13
19202324
1.73 – 1.99
(0.068 – 0.078)
0.05 – 0.21
(0.002 – 0.008)
0.65
(0.0256)
BSC 0.25 – 0.38
(0.010 – 0.015)
NOTE: DIMENSIONS ARE IN MILLIMETERS
DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.152mm (0.006") PER SIDE
DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.254mm (0.010") PER SIDE
*
**
PACKAGE DIMENSIONS
13-11
G Package
36-Lead Plastic SSOP (5.3mm)
(LTC DWG # 05-08-1640)
G36 SSOP 1098
0.13 – 0.22
(0.005 – 0.009)
0° – 8°
0.55 – 0.95
(0.022 – 0.037)
5.20 – 5.38**
(0.205 – 0.212)
7.65 – 7.90
(0.301 – 0.311)
12345678 9 10 11 12 14 15 16 17 1813
12.67 – 12.93*
(0.499 – 0.509)
2526 22 21 20 19232427282930313233343536
1.73 – 1.99
(0.068 – 0.078)
0.05 – 0.21
(0.002 – 0.008)
0.65
(0.0256)
BSC 0.25 – 0.38
(0.010 – 0.015)
NOTE: DIMENSIONS ARE IN MILLIMETERS
DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.152mm (0.006") PER SIDE
DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.254mm (0.010") PER SIDE
*
**
GN Package
16-Lead Plastic SSOP (Narrow 0.150)
(LTC DWG # 05-08-1641)
GN16 (SSOP) 1098
* DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
12
345
6
78
0.229 – 0.244
(5.817 – 6.198)
0.150 – 0.157**
(3.810 – 3.988)
16 15 14 13
0.189 – 0.196*
(4.801 – 4.978)
12 11 10 9
0.016 – 0.050
(0.406 – 1.270)
0.015 ± 0.004
(0.38 ± 0.10) × 45°
0° – 8° TYP
0.007 – 0.0098
(0.178 – 0.249)
0.053 – 0.068
(1.351 – 1.727)
0.008 – 0.012
(0.203 – 0.305)
0.004 – 0.0098
(0.102 – 0.249)
0.0250
(0.635)
BSC
0.009
(0.229)
REF
PACKAGE DIMENSIONS
13-12
GN Package
20-Lead Plastic SSOP (Narrow 0.150)
(LTC DWG # 05-08-1641)
0.337 – 0.344*
(8.560 – 8.737)
GN20 (SSOP) 1098
* DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
12
345
6
78910
0.229 – 0.244
(5.817 – 6.198)
0.150 – 0.157**
(3.810 – 3.988)
1617181920 15 14 13 12 11
0.016 – 0.050
(0.406 – 1.270)
0.015 ± 0.004
(0.38 ± 0.10) × 45°
0° – 8° TYP
0.007 – 0.0098
(0.178 – 0.249)
0.053 – 0.068
(1.351 – 1.727)
0.008 – 0.012
(0.203 – 0.305)
0.004 – 0.0098
(0.102 – 0.249)
0.0250
(0.635)
BSC
0.058
(1.473)
REF
0.337 – 0.344*
(8.560 – 8.738)
GN24 (SSOP) 1098
* DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
12
345
6
78 9 10 11 12
0.229 – 0.244
(5.817 – 6.198)
0.150 – 0.157**
(3.810 – 3.988)
161718192021222324 15 14 13
0.016 – 0.050
(0.406 – 1.270)
0.015 ± 0.004
(0.38 ± 0.10) × 45°
0° – 8° TYP
0.007 – 0.0098
(0.178 – 0.249)
0.053 – 0.068
(1.351 – 1.727)
0.008 – 0.012
(0.203 – 0.305)
0.004 – 0.0098
(0.102 – 0.249)
0.0250
(0.635)
BSC
0.033
(0.838)
REF
GN Package
24-Lead Plastic SSOP (Narrow 0.150)
(LTC DWG # 05-08-1641)
PACKAGE DIMENSIONS
13-13
GN Package
28-Lead Plastic SSOP (Narrow 0.150)
(LTC DWG # 05-08-1641)
0.386 – 0.393*
(9.804 – 9.982)
GN28 (SSOP) 1098
* DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
12
345
6
78 9 10 11 12
0.229 – 0.244
(5.817 – 6.198)
0.150 – 0.157**
(3.810 – 3.988)
202122232425262728 19 18 17
13 14
1615
0.016 – 0.050
(0.406 – 1.270)
0.015 ± 0.004
(0.38 ± 0.10) × 45°
0° – 8° TYP
0.0075 – 0.0098
(0.191 – 0.249)
0.053 – 0.069
(1.351 – 1.748)
0.008 – 0.012
(0.203 – 0.305)
0.004 – 0.009
(0.102 – 0.249)
0.0250
(0.635)
BSC
0.033
(0.838)
REF
GW36 SSOP 1098
0° – 8° TYP
0.231 – 0.3175
(0.0091 – 0.0125)
0.610 – 1.016
(0.024 – 0.040)
7.417 – 7.595**
(0.292 – 0.299)
× 45°
0.254 – 0.406
(0.010 – 0.016)
2.286 – 2.387
(0.090 – 0.094)
0.127 – 0.305
(0.005 – 0.0115)
2.463 – 2.641
(0.097 – 0.104)
0.800
(0.0315)
BSC
0.304 – 0.431
(0.012 – 0.017)
15.290 – 15.544*
(0.602 – 0.612)
123456789101112131415161718
10.160 – 10.414
(0.400 – 0.410)
36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19
DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.152mm (0.006") PER SIDE
*
NOTE: DIMENSIONS ARE IN MILLIMETERS
DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.254mm (0.010") PER SIDE
**
GW Package
36-Lead Plastic SSOP (Wide 7.62mm)
(LTC DWG # 05-08-1642)
PACKAGE DIMENSIONS
13-14
GW Package
44-Lead Plastic SSOP (Wide 7.62mm)
(LTC DWG # 05-08-1642)
G44 SSOP 1098
0° – 8° TYP
0.231 – 0.3175
(0.0091 – 0.0125)
0.610 – 1.016
(0.024 – 0.040)
7.417 – 7.595**
(0.292 – 0.299)
× 45°
0.254 – 0.406
(0.010 – 0.016)
2.286 – 2.387
(0.090 – 0.094)
0.127 – 0.292
(0.005 – 0.0115)
2.463 – 2.641
(0.097 – 0.104)
0.800
(0.0315)
BSC
0.304 – 0.431
(0.012 – 0.017)
17.805 – 18.059*
(0.701 – 0.711)
123456789101112131415161718192021
10.160 – 10.414
(0.400 – 0.410)
22
44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23
DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.152mm (0.006") PER SIDE
NOTE: DIMENSIONS ARE IN MILLIMETERS
*DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.254mm (0.010") PER SIDE
**
H Package
8-Lead TO-5 Metal Can (0.200 PCD)
(LTC DWG # 05-08-1320)
0.050
(1.270)
MAX
0.016 – 0.021**
(0.406 – 0.533)
0.010 – 0.045*
(0.254 – 1.143)
SEATING
PLANE
0.040
(1.016)
MAX 0.165 – 0.185
(4.191 – 4.699)
GAUGE
PLANE
REFERENCE
PLANE
0.500 – 0.750
(12.700 – 19.050)
0.305 – 0.335
(7.747 – 8.509)
0.335 – 0.370
(8.509 – 9.398)
DIA
0.200
(5.080)
TYP
0.027 – 0.045
(0.686 – 1.143)
0.028 – 0.034
(0.711 – 0.864)
0.110 – 0.160
(2.794 – 4.064)
INSULATING
STANDOFF
45°TYP
H8(TO-5) 0.200 PCD 1197
LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND 0.045" BELOW THE REFERENCE PLANE
FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS 0.016 – 0.024
(0.406 – 0.610)
*
**
PIN 1
PACKAGE DIMENSIONS
13-15
H Package
8-Lead TO-5 Metal Can (0.230 PCD)
(LTC DWG # 05-08-1321)
0.050
(1.270)
MAX
0.016 – 0.021**
(0.406 – 0.533)
0.010 – 0.045*
(0.254 – 1.143)
SEATING
PLANE
0.040
(1.016)
MAX 0.165 – 0.185
(4.191 – 4.699)
GAUGE
PLANE
REFERENCE
PLANE
0.500 – 0.750
(12.700 – 19.050)
0.305 – 0.335
(7.747 – 8.509)
0.335 – 0.370
(8.509 – 9.398)
DIA
0.230
( 5.842)
TYP
0.027 – 0.045
(0.686 – 1.143)
0.028 – 0.034
(0.711 – 0.864)
0.110 – 0.160
(2.794 – 4.064)
INSULATING
STANDOFF
36°BSC
H10(TO-5) 1197
LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND 0.045" BELOW THE REFERENCE PLANE
FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS 0.016 – 0.024
(0.406 – 0.610)
*
**
PIN 1
H Package
10-Lead TO-5 Metal Can
(LTC DWG # 05-08-1322)
0.050
(1.270)
MAX
0.016 – 0.021**
(0.406 – 0.533)
0.010 – 0.045*
(0.254 – 1.143)
SEATING
PLANE
0.040
(1.016)
MAX 0.165 – 0.185
(4.191 – 4.699)
GAUGE
PLANE
REFERENCE
PLANE
0.500 – 0.750
(12.700 – 19.050)
0.305 – 0.335
(7.747 – 8.509)
0.335 – 0.370
(8.509 – 9.398)
DIA
0.230
(5.842)
TYP
0.027 – 0.045
(0.686 – 1.143)
0.028 – 0.034
(0.711 – 0.864)
0.110 – 0.160
(2.794 – 4.064)
INSULATING
STANDOFF
45°TYP
H8 (TO-5) 0.230 PCD 1197
LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND 0.045" BELOW THE REFERENCE PLANE
FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS 0.016 – 0.024
(0.406 – 0.610)
*
**
PIN 1
PACKAGE DIMENSIONS
13-16
H Package
4-Lead TO-39 Metal Can
(LTC DWG # 05-08-1331)
0.016 – 0.021**
(0.406 – 0.533)
DIA
0.025
(0.635)
MAX
0.115 – 0.150
(2.921 – 3.810)
0.500
(12.700)
MIN
0.178 – 0.195
(4.521 – 4.953)
0.209 – 0.230
(5.309 – 5.842)
H3(TO-52) 1098
0.100
(2.540)
TYP
45°
0.050
(1.270)
TYP
0.050
(1.270)
TYP
0.028 – 0.048
(0.711 – 1.219)
0.036 – 0.046
(0.914 – 1.168)
REFERENCE
PLANE *
LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND 0.045" BELOW THE REFERENCE PLANE
FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS 0.016 – 0.024
(0.406 – 0.610)
*
**
PIN 1
H Package
3-Lead TO-52 Metal Can
(LTC DWG # 05-08-1350)
H Package
2-Lead and 3-Lead TO-46 Metal Can
(LTC DWG # 05-08-1340)
0.016 – 0.021**
(0.406 – 0.533)
DIA
0.025
(0.635)
MAX
0.085 – 0.105
(2.159 – 2.667)
0.500
(12.700)
MIN
0.178 – 0.195
(4.521 – 4.953)
0.209 – 0.219
(5.309 – 5.537)
0.100
(2.540)
TYP
45°
H02/03(TO-46) 1098
0.050
(1.270)
TYP
0.050
(1.270)
TYP
0.028 – 0.048
(0.711 – 1.219)
0.036 – 0.046
(0.914 – 1.168)
FOR 3-LEAD PACKAGE ONLY
REFERENCE
PLANE *
LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND 0.045" BELOW THE REFERENCE PLANE
FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS 0.016 – 0.024
(0.406 – 0.610)
*
**
PIN 1
0.016 – 0.021**
(0.406 – 0.533)
DIA
0.025
(0.635)
MAX
REFERENCE
PLANE
0.085 – 0.105
(2.159 – 2.667)
0.500
(12.700)
MIN
0.178 – 0.195
(4.521 – 4.953)
0.209 – 0.219
(5.309 – 5.563)
0.100
(2.540)
TYP
45°
H4(TO-46) 1098
0.050
(1.270)
TYP
0.050
(1.270)
TYP
0.028 – 0.048
(0.711 – 1.219)
0.036 – 0.046
(0.914 – 1.168)
*
LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND 0.045" BELOW THE REFERENCE PLANE
FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS 0.016 – 0.024
(0.406 – 0.610)
*
**
PIN 1
H Package
4-Lead TO-46 Metal Can
(LTC DWG # 05-08-1341)
0.016 – 0.021**
(0.406 – 0.533)
DIA
0.050
(1.270)
MAX 0.165 – 0.185
(4.191 – 4.699)
0.500
(12.700)
MIN
0.305 – 0.335
(7.747 – 8.509)
0.350 – 0.370
(8.890 – 9.398)
0.200
(5.080)
TYP
45°
H4(TO-39) 1098
0.100
(2.540)
0.100
(2.540)
0.029 – 0.045
(0.737 – 1.143)
0.028 – 0.034
(0.711 – 0.864)
LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND 0.045" BELOW THE REFERENCE PLANE
FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS 0.016 – 0.024
(0.406 – 0.610)
*
**
REFERENCE
PLANE *
PIN 1
H Package
3-Lead TO-39 Metal Can
(LTC DWG # 05-08-1330)
0.016 – 0.021**
(0.406 – 0.533)
DIA
0.050
(1.270)
MAX 0.165 – 0.185
(4.191 – 4.699)
0.500
(12.700)
MIN
0.305 – 0.335
(7.747 – 8.509)
0.350 – 0.370
(8.890 – 9.398)
0.200
(5.080)
TYP
45°
H3(TO-39) 1098
0.100
(2.540)
0.100
(2.540)
0.029 – 0.045
(0.737 – 1.143)
0.028 – 0.034
(0.711 – 0.864)
REFERENCE
PLANE *
LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND 0.045" BELOW THE REFERENCE PLANE
FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS 0.016 – 0.024
(0.406 – 0.610)
*
**
PIN 1
PACKAGE DIMENSIONS
13-17
J8 Package
8-Lead CERDIP (Narrow 0.300, Hermetic)
(LTC DWG # 05-08-1110)
J Package
14-Lead CERDIP (Narrow 0.300, Hermetic)
(LTC DWG # 05-08-1110)
J8 1298
0.014 – 0.026
(0.360 – 0.660)
0.200
(5.080)
MAX
0.015 – 0.060
(0.381 – 1.524)
0.125
3.175
MIN
0.100
(2.54)
BSC
0.300 BSC
(0.762 BSC)
0.008 – 0.018
(0.203 – 0.457) 0° – 15°
0.005
(0.127)
MIN
0.405
(10.287)
MAX
0.220 – 0.310
(5.588 – 7.874)
1234
87
65
0.025
(0.635)
RAD TYP
0.045 – 0.068
(1.143 – 1.727)
FULL LEAD
OPTION
0.023 – 0.045
(0.584 – 1.143)
HALF LEAD
OPTION
CORNER LEADS OPTION
(4 PLCS)
0.045 – 0.065
(1.143 – 1.651)
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
J14 1298
0.045 – 0.065
(1.143 – 1.651)
0.100
(2.54)
BSC
0.014 – 0.026
(0.360 – 0.660)
0.200
(5.080)
MAX
0.015 – 0.060
(0.381 – 1.524)
0.125
(3.175)
MIN
0.300 BSC
(0.762 BSC)
0.008 – 0.018
(0.203 – 0.457) 0° – 15°
1234567
0.220 – 0.310
(5.588 – 7.874)
0.785
(19.939)
MAX
0.005
(0.127)
MIN 14 11 891013 12
0.025
(0.635)
RAD TYP
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
PACKAGE DIMENSIONS
13-18
J Package
16-Lead CERDIP (Narrow 0.300, Hermetic)
(LTC DWG # 05-08-1110)
J Package
18-Lead CERDIP (Narrow 0.300, Hermetic)
(LTC DWG # 05-08-1110)
J16 1298
0.015 – 0.060
(0.380 – 1.520)
0.100
(2.54)
BSC
0.014 – 0.026
(0.360 – 0.660)
0.045 – 0.065
(1.143 – 1.651)
0.200
(5.080)
MAX
0.125
(3.175)
MIN
0.008 – 0.018
(0.203 – 0.457) 0° – 15°
12345678
0.220 – 0.310
(5.588 – 7.874)
0.840
(21.336)
MAX
0.005
(0.127)
MIN 16 13 9
10
11121415
0.025
(0.635)
RAD TYP
0.300 BSC
(0.762 BSC)
0.045 – 0.068
(1.143 – 1.727)
FULL LEAD
OPTION
0.023 – 0.045
(0.584 – 1.143)
HALF LEAD
OPTION
CORNER LEADS OPTION
(4 PLCS)
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
J18 1298
0.015 – 0.060
(0.380 – 1.520)
0.100
(2.54)
BSC
0.014 – 0.026
(0.360 – 0.660)
0.045 – 0.065
(1.143 – 1.651)
0.200
(5.080)
MAX
0.125
(3.175)
MIN
0.008 – 0.018
(0.203 – 0.457) 0° – 15°
12345678
0.220 – 0.310
(5.590 – 7.870)
0.960
(24.384)
MAX
0.005
(0.127)
MIN 16 13
9
10
11
12
1415
17
18
0.025
(0.635)
RAD TYP
0.300 BSC
(0.762 BSC)
0.045 – 0.068
(1.143 – 1.727)
FULL LEAD
OPTION
0.023 – 0.045
(0.584 – 1.143)
HALF LEAD
OPTION
CORNER LEADS OPTION
(4 PLCS)
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
PACKAGE DIMENSIONS
13-19
J Package
20-Lead CERDIP (Narrow 0.300, Hermetic)
(LTC DWG # 05-08-1110)
J Package
24-Lead CERDIP (Narrow 0.300, Hermetic)
(DWG # 05-08-1110)
J20 1298
37
56 109
142 8
11
20 16 1517 14 13 1219 18
0.005
(0.127)
MIN
0.025
(0.635)
RAD TYP
0.220 – 0.310
(5.588 – 7.874)
1.060
(26.924)
MAX
0° – 15°
0.008 – 0.018
(0.203 – 0.457)
0.015 – 0.060
(0.381 – 1.524)
0.125
(3.175)
MIN
0.014 – 0.026
(0.356 – 0.660)
0.045 – 0.065
(1.143 – 1.651) 0.100
(2.54)
BSC
0.200
(5.080)
MAX
0.300 BSC
(0.762 BSC)
0.045 – 0.068
(1.143 – 1.727)
FULL LEAD
OPTION
0.023 – 0.045
(0.584 – 1.143)
HALF LEAD
OPTION
CORNER LEADS OPTION
(4 PLCS)
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
J24 1298
0.015 – 0.060
(0.381 – 1.524)
0.125
(3.175)
MIN 0.014 – 0.026
(0.360 – 0.660)
0.100
(2.54)
BSC
0.200
(5.080)
MAX
0.045 – 0.065
(1.143 – 1.651)
0.008 – 0.018
(0.203 – 0.457)
20 16 1517 14 13
19
11
37
56 10
912
142 8
18
0.220 – 0.310
(5.588 – 7.874)
1.290
(32.77)
MAX
21
222324
0.025
(0.635)
RAD TYP
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
0° – 15°
0.300 BSC
(0.762 BSC)
0.005
(0.127)
MIN
PACKAGE DIMENSIONS
13-20
JW Package
28-Lead CERDIP (Wide 0.600, Hermetic)
(LTC DWG # 05-08-1120)
K Package
2-Lead TO-3 Metal Can
(LTC DWG # 05-08-1310)
0.600 TYP
(15.240 TYP)
0.008 – 0.018
(0.203 – 0.457)
0.685 +0.025
–0.060
+0.635
–1.524
17.40
()
J28 1298
0.015 – 0.075
(0.381 – 1.904)
0.125
(3.175)
MIN 0.005
(0.127)
MIN
0.100
(2.54)
BSC
0.225
(5.715)
MAX
0.014 – 0.026
(0.360 – 0.660)
0.045 – 0.065
(1.143 – 1.651)
11
37
20 16 15
56109
17
1413
12
14
2
19
8
18
0.510 – 0.620
(12.95 – 15.75)
MAX
1.490
(37.85)
MAX
21
22
23
28 24
25
26
27
0.025
(0.635)
RAD TYP
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP OR TIN PLATE LEADS
0° – 15°
K2 (TO-3) 1098
0.038 – 0.043
(0.965 – 1.09)
0.060 – 0.135
(1.524 – 3.429)
0.320 – 0.350
(8.13 – 8.89)
0.420 – 0.480
(10.67 – 12.19)
0.760 – 0.775
(19.30 – 19.69)
0.490 – 0.510
(12.45 – 12.95)
R
0.167 – 0.177
(4.24 – 4.49)
R
0.151 – 0.161
(3.86 – 4.09)
DIA, 2PLCS
1.177 – 1.197
(29.90 – 30.40)
0.655 – 0.675
(16.64 – 17.15)
0.067 – 0.077
(1.70 – 1.96)
0.210 – 0.220
(5.33 – 5.59)
0.425 – 0.435
(10.80 – 11.05)
K Package
2-Lead TO-3 Metal Can
(60mil Diameter Leads)
(LTC DWG # 05-08-1312)
K2(TO-3) 1098
0.058 – 0.062
(1.47 – 1.57)
0.320 – 0.350
(8.13 – 8.89)
0.420 – 0.480
(10.67 – 12.19)
0.760 – 0.775
(19.30 – 19.69)
0.490 – 0.510
(12.45 – 12.95)
R
0.167 – 0.177
(4.24 – 4.49)
R
0.151 – 0.161
(3.86 – 4.09)
DIA, 2 PLACES
1.177 – 1.197
(29.90 – 30.40)
0.655 – 0.675
(16.64 – 17.15)
0.067 – 0.077
(1.70 – 1.96)
0.210 – 0.220
(5.33 – 5.59)
0.425 – 0.435
(10.80 – 11.05)
0.060 – 0.135
(1.524 – 3.429)
PACKAGE DIMENSIONS
13-21
K Package
4-Lead TO-3 Metal Can
(LTC DWG # 05-08-1311)
K4(TO-3) 1098
72°
18°
0.490 – 0.510
(12.45 – 12.95)
R
0.470 TP
P.C.D.
0.167 – 0.177
(4.24 – 4.49)
R
0.151 – 0.161
(3.84 – 4.09)
DIA 2 PLC
0.655 – 0.675
(16.64 – 19.05)
1.177 – 1.197
(29.90 – 30.40)
0.038 – 0.043
(0.965 – 1.09)
0.060 – 0.135
(1.524 – 3.429)
0.320 – 0.350
(8.13 – 8.89)
0.420 – 0.480
(10.67 – 12.19)
0.760 – 0.775
(19.30 – 19.69)
L Package
20-Pin Leadless Chip Carrier (Rectangular, Hermetic)
(LTC DWG # 05-08-1250)
TOP
0.020
(0.508)
REF
× 45° 3PLCs
0.440
(11.176)
MAX
0.305
(7.747)
MAX
0.060 – 0.075
(1.524 – 1.95)
0.050 – 0.065
(1.270 – 1.651)
BOTTOM
0.045 – 0.055
(1.143 – 1.397)
0.420 – 0.440
(10.668 – 11.176)
0.045 – 0.055
(1.143 – 1.397)
0.280 – 0.305
(7.112 – 7.747) 0.010
(0.254)
REF
× 45°
0.015
(0.381)
MIN
0.022 – 0.028
(0.559 – 0.711)
0.003 – 0.015
(0.076 – 0.381)
0.008
(0.203)
RAD
0.050
(1.270)
TYP
PIN 1
0.075 – 0.095
(1.905 – 2.413)
L20(REC) 1197
PACKAGE DIMENSIONS
13-22
LS Package
20-Pin Leadless Chip Carrier (Square 0.350, Hermetic)
(LTC DWG # 05-08-1260)
M Package
3-Lead Plastic DD Pak
(LTC DWG # 05-08-1460)
MS8 Package
8-Lead Plastic MSOP
(LTC DWG # 05-08-1660)
0.064 – 0.090
(1.626 – 2.286)
0.054 – 0.076
(1.371 – 1.930)
L20(SQ) 1197
TOP
0.300 ± 0.004
(7.62 ± 0.102)
SQ.
0.350 ± 0.005
(8.89 ± 0.127)
0.085 ± 0.008
(2.16 ± 0.203)
0.350 ± 0.005
(8.89 ± 0.127)
0.050 ± 0.005
(1.270 ± 0.127)
0.020
(0.508)
REF
× 45°
0.015
(0.381)
TYP
0.040
(0.508)
REF
× 45° 3 PLCs
0.003 – 0.015
(0.076 – 0.381)
0.006 – 0.022
(0.152 – 0.558)
0.050
(1.270)
TYP
PIN 1
BOTTOM
0.100
2.54
BSC
0.200
5.08
BSC
MSOP (MS8) 1098
* DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006"
(
0.152mm
)
PER SIDE
0.021 ± 0.006
(0.53 ± 0.015)
0° – 6° TYP
SEATING
PLANE
0.007
(0.18)
0.040 ± 0.006
(1.02 ± 0.15)
0.012
(0.30)
REF
0.006 ± 0.004
(0.15 ± 0.102)
0.034 ± 0.004
(0.86 ± 0.102)
0.0256
(0.65)
BSC
12
34
0.193 ± 0.006
(4.90 ± 0.15)
8765
0.118 ± 0.004*
(3.00 ± 0.102)
0.118 ± 0.004**
(3.00 ± 0.102)
M (DD3) 1098
0.050
(1.270)
BSC
0.143 +0.012
–0.020
()
3.632 +0.305
–0.508
0.090 – 0.110
(2.286 – 2.794) 0.013 – 0.023
(0.330 – 0.584)
0.095 – 0.115
(2.413 – 2.921)
0.004 +0.008
–0.004
()
0.102 +0.203
–0.102
0.050 ± 0.012
(1.270 ± 0.305)
0.059
(1.499)
TYP
0.045 – 0.055
(1.143 – 1.397)
0.165 – 0.180
(4.191 – 4.572)
0.330 – 0.370
(8.382 – 9.398)
0.060
(1.524)
TYP
0.390 – 0.415
(9.906 – 10.541)
15° TYP
0.300
(7.620)
0.075
(1.905)
0.183
(4.648)
0.060
(1.524)
0.060
(1.524)
0.256
(6.502)
BOTTOM VIEW OF DD PAK
HATCHED AREA IS SOLDER PLATED
COPPER HEAT SINK
PACKAGE DIMENSIONS
13-23
MS10 Package
10-Lead Plastic MSOP
(LTC DWG # 05-08-1661)
MSOP (MS10) 1098
* DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006"
(
0.152mm
)
PER SIDE
0.021 ± 0.006
(0.53 ± 0.015)
0° – 6° TYP
SEATING
PLANE
0.007
(0.18)
0.040 ± 0.006
(1.02 ± 0.15)
0.009
(0.228)
REF
0.006 ± 0.004
(0.15 ± 0.102)
0.034 ± 0.004
(0.86 ± 0.102)
0.0197
(0.50)
BSC
12345
0.193 ± 0.006
(4.90 ± 0.15)
8910 76
0.118 ± 0.004*
(3.00 ± 0.102)
0.118 ± 0.004**
(3.00 ± 0.102)
N8 Package
8-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
N8 1098
0.100
(2.54)
BSC
0.065
(1.651)
TYP
0.045 – 0.065
(1.143 – 1.651)
0.130 ± 0.005
(3.302 ± 0.127)
0.020
(0.508)
MIN
0.018 ± 0.003
(0.457 ± 0.076)
0.125
(3.175)
MIN
12 34
87 65
0.255 ± 0.015*
(6.477 ± 0.381)
0.400*
(10.160)
MAX
0.009 – 0.015
(0.229 – 0.381)
0.300 – 0.325
(7.620 – 8.255)
0.325 +0.035
–0.015
+0.889
–0.381
8.255
()
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
PACKAGE DIMENSIONS
13-24
N Package
16-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
N16 1098
0.255 ± 0.015*
(6.477 ± 0.381)
0.770*
(19.558)
MAX
16
12345678
910
11
12
13
14
15
0.020
(0.508)
MIN
0.125
(3.175)
MIN
0.130 ± 0.005
(3.302 ± 0.127)
0.065
(1.651)
TYP
0.045 – 0.065
(1.143 – 1.651)
0.018 ± 0.003
(0.457 ± 0.076)
0.100
(2.54)
BSC
0.009 – 0.015
(0.229 – 0.381)
0.300 – 0.325
(7.620 – 8.255)
0.325 +0.035
–0.015
+0.889
–0.381
8.255
()
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
N Package
14-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
N14 1098
0.020
(0.508)
MIN
0.125
(3.175)
MIN
0.130 ± 0.005
(3.302 ± 0.127)
0.045 – 0.065
(1.143 – 1.651)
0.065
(1.651)
TYP
0.018 ± 0.003
(0.457 ± 0.076)
0.100
(2.54)
BSC
0.005
(0.125)
MIN
0.255 ± 0.015*
(6.477 ± 0.381)
0.770*
(19.558)
MAX
31 24567
8910
11
1213
14
0.009 – 0.015
(0.229 – 0.381)
0.300 – 0.325
(7.620 – 8.255)
0.325 +0.035
–0.015
+0.889
–0.381
8.255
()
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
PACKAGE DIMENSIONS
13-25
N Package
18-Lead PDIP Isolation Barrier (Narrow 0.300)
(LTC DWG # 05-08-1590)
N18 1197
0.015
(0.381)
MIN
0.040
(1.016)
TYP
0.125
(3.175)
MIN
0.130 ± 0.005
(3.302 ± 0.127)
0.065
(1.651)
TYP
0.050 – 0.070
(1.27 – 1.778)
0.018 ± 0.003
(0.457 ± 0.076)
0.005
(0.127)
MIN
0.100
(2.54)
BSC
0.255 ± 0.015*
(6.477 ± 0.381)
0.900*
(22.860)
MAX
18
1789
1011
12
0.008 – 0.014
(0.203 – 0.356)
0.300 – 0.325
(7.620 – 8.255)
0.325 +0.035
–0.015
+0.889
–0.381
8.255
()
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
N18 1098
0.020
(0.508)
MIN
0.125
(3.175)
MIN
0.130 ± 0.005
(3.302 ± 0.127)
0.065
(1.651)
TYP
0.045 – 0.065
(1.143 – 1.651)
0.018 ± 0.003
(0.457 ± 0.076)
0.005
(0.127)
MIN
0.100
(2.54)
BSC
0.255 ± 0.015*
(6.477 ± 0.381)
0.900*
(22.860)
MAX
18
123456789
1011
121314
16 1517
0.009 – 0.015
(0.229 – 0.381)
0.300 – 0.325
(7.620 – 8.255)
0.325 +0.035
–0.015
+0.889
–0.381
8.255
()
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
N Package
18-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
PACKAGE DIMENSIONS
13-26
N Package
24-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
N24 1098
0.255 ± 0.015*
(6.477 ± 0.381)
1.265*
(32.131)
MAX
12345678910
19
11 12
131416 151718
20
21
2223
24
0.020
(0.508)
MIN
0.125
(3.175)
MIN
0.130 ± 0.005
(3.302 ± 0.127)
0.065
(1.651)
TYP
0.045 – 0.065
(1.143 – 1.651)
0.018 ± 0.003
(0.457 ± 0.076)
0.100
(2.54)
BSC
0.009 – 0.015
(0.229 – 0.381)
0.300 – 0.325
(7.620 – 8.255)
0.325 +0.035
–0.015
+0.889
–0.381
8.255
()
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
N20 1098
0.020
(0.508)
MIN
0.125
(3.175)
MIN
0.130 ± 0.005
(3.302 ± 0.127)
0.065
(1.651)
TYP
0.045 – 0.065
(1.143 – 1.651)
0.018 ± 0.003
(0.457 ± 0.076)
0.005
(0.127)
MIN
0.100
(2.54)
BSC
0.255 ± 0.015*
(6.477 ± 0.381)
1.040*
(26.416)
MAX
12345678910
19 1112
131416 1517
18
20
0.009 – 0.015
(0.229 – 0.381)
0.300 – 0.325
(7.620 – 8.255)
0.325 +0.035
–0.015
+0.889
–0.381
8.255
()
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
N Package
20-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
PACKAGE DIMENSIONS
13-27
NW Package
28-Lead PDIP (Wide 0.600)
(LTC DWG # 05-08-1520)
N28 1098
0.505 – 0.560*
(12.827 – 14.224)
1.455*
(36.957)
MAX
12 3456789
10
27 19
20212224 23
252628
11 12 13 14
15
16
1718
0.009 – 0.015
(0.229 – 0.381)
0.625 +0.035
–0.015
+0.889
–0.381
15.87
()
0.600 – 0.625
(15.240 – 15.875)
0.070
(1.778)
TYP
0.015
(0.381)
MIN
0.125
(3.175)
MIN
0.150 ± 0.005
(3.810 ± 0.127)
0.018 ± 0.003
(0.457 ± 0.076)
0.035 – 0.080
(0.889 – 2.032)
0.100
(2.54)
BSC
0.045 – 0.065
(1.143 – 1.651)
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
N Package
28-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
N28 1098
0.255 ± 0.015*
(6.477 ± 0.381)
1.370*
(34.789)
MAX
3456789
10 11 12
21
13 14
151618 171920
22
23
2425
26
2
27
1
28
0.020
(0.508)
MIN
0.125
(3.175)
MIN
0.130 ± 0.005
(3.302 ± 0.127)
0.065
(1.651)
TYP
0.045 – 0.065
(1.143 – 1.651)
0.018 ± 0.003
(0.457 ± 0.076)
0.005
(0.127)
MIN
0.100
(2.54)
BSC
0.009 – 0.015
(0.229 – 0.381)
0.300 – 0.325
(7.620 – 8.255)
0.325 +0.035
–0.015
+0.889
–0.381
8.255
()
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
PACKAGE DIMENSIONS
13-28
P Package
3-Lead Plastic TO-3P (Similar to TO-247)
(LTC DWG # 05-08-1450)
0.580 – 0.6OO
(14.73 – 15.24)
0.170
(4.32)
MAX
0.325
(8.255)
0.580
(14.732)
0.560
(14.224) 0.620 – 0.64O
(15.75 – 16.26)
0.170 – 0.2OO
(4.32 – 5.08)
MOUNTING HOLE
0.115 – 0.145
(2.92 – 3.68)
DIA
0.580 – 0.6OO
(14.73 – 15.24)
0.830 – 0.870
(21.08 – 22.10)
0.780 – 0.800
(19.81 – 20.32)
0.620 – 0.64O
(15.75 – 16.26)
0.215
(5.46)
BSC
0.113 – 0.123
(2.87 – 3.12)
0.042 – 0.052
(1.07 – 1.32)
0.074 – 0.084
(1.88 – 2.13)
0.187 – 0.207
(4.75 – 5.26)
0.060 – 0.080
(1.52 – 2.03)
18° – 22°
3° – 7°
0.087 – 0.102
(2.21 – 2.59)
0.020 – 0.040
(0.51 – 1.02)
EJECTOR PIN MARKS
0.105 – 0.125
(2.67 – 3.18)
DIA
P3 0996
0.098
(2.489)
0.124
(3.149)
0.700
(17.780)
0.275
(6.985)
BOTTOM VIEW OF TO-3P
HATCHED AREA IS SOLDER PLATED
COPPER HEAT SINK
Q Package
5-Lead Plastic DD Pak
(LTC DWG # 05-08-1461)
Q(DD5) 1098
0.028 – 0.038
(0.711 – 0.965)
0.143 +0.012
–0.020
()
3.632 +0.305
–0.508
0.067
(1.70)
BSC
0.013 – 0.023
(0.330 – 0.584)
0.095 – 0.115
(2.413 – 2.921)
0.004 +0.008
–0.004
()
0.102 +0.203
–0.102
0.050 ± 0.012
(1.270 ± 0.305)
0.059
(1.499)
TYP
0.045 – 0.055
(1.143 – 1.397)
0.165 – 0.180
(4.191 – 4.572)
0.330 – 0.370
(8.382 – 9.398)
0.060
(1.524)
TYP
0.390 – 0.415
(9.906 – 10.541)
15° TYP
0.300
(7.620)
0.075
(1.905)
0.183
(4.648)
0.060
(1.524)
0.060
(1.524)
0.256
(6.502)
BOTTOM VIEW OF DD PAK
HATCHED AREA IS SOLDER PLATED
COPPER HEAT SINK
PACKAGE DIMENSIONS
13-29
R Package
7-Lead Plastic DD Pak
(LTC DWG # 05-08-1462)
R (DD7) 1098
0.026 – 0.036
(0.660 – 0.914)
0.143 +0.012
–0.020
()
3.632 +0.305
–0.508
0.050
(1.27)
BSC
0.013 – 0.023
(0.330 – 0.584)
0.095 – 0.115
(2.413 – 2.921)
0.004 +0.008
–0.004
()
0.102 +0.203
–0.102
0.050 ± 0.012
(1.270 ± 0.305)
0.059
(1.499)
TYP
0.045 – 0.055
(1.143 – 1.397)
0.165 – 0.180
(4.191 – 4.572)
0.330 – 0.370
(8.382 – 9.398)
0.060
(1.524)
TYP
0.390 – 0.415
(9.906 – 10.541)
15° TYP
0.300
(7.620)
0.075
(1.905)
0.183
(4.648)
0.060
(1.524)
0.060
(1.524)
0.256
(6.502)
BOTTOM VIEW OF DD PAK
HATCHED AREA IS SOLDER PLATED
COPPER HEAT SINK
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.016 – 0.050
(0.406 – 1.270)
0.010 – 0.020
(0.254 – 0.508)× 45°
0°– 8° TYP
0.008 – 0.010
(0.203 – 0.254)
SO8 1298
0.053 – 0.069
(1.346 – 1.752)
0.014 – 0.019
(0.355 – 0.483)
TYP
0.004 – 0.010
(0.101 – 0.254)
0.050
(1.270)
BSC
1234
0.150 – 0.157**
(3.810 – 3.988)
8765
0.189 – 0.197*
(4.801 – 5.004)
0.228 – 0.244
(5.791 – 6.197)
DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
*
**
PACKAGE DIMENSIONS
13-30
S Package
14-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
1234
0.150 – 0.157**
(3.810 – 3.988)
14 13
0.337 – 0.344*
(8.560 – 8.738)
0.228 – 0.244
(5.791 – 6.197)
12 11 10 9
567
8
0.016 – 0.050
(0.406 – 1.270)
0.010 – 0.020
(0.254 – 0.508)× 45°
0° – 8° TYP
0.008 – 0.010
(0.203 – 0.254)
S14 1298
0.053 – 0.069
(1.346 – 1.752)
0.014 – 0.019
(0.355 – 0.483)
TYP
0.004 – 0.010
(0.101 – 0.254)
0.050
(1.270)
BSC
DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
*
**
0.016 – 0.050
(0.406 – 1.270)
0.010 – 0.020
(0.254 – 0.508)× 45°
0° – 8° TYP
0.008 – 0.010
(0.203 – 0.254)
12345678
0.150 – 0.157**
(3.810 – 3.988)
16 15 14 13
0.386 – 0.394*
(9.804 – 10.008)
0.228 – 0.244
(5.791 – 6.197)
12 11 10 9
S16 1098
0.053 – 0.069
(1.346 – 1.752)
0.014 – 0.019
(0.355 – 0.483)
TYP
0.004 – 0.010
(0.101 – 0.254)
0.050
(1.270)
BSC
DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
*
**
S Package
16-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
PACKAGE DIMENSIONS
13-31
SW Package
16-Lead Plastic Small Outline (Wide 0.300)
(LTC DWG # 05-08-1620)
SW Package
18-Lead Plastic Small Outline (Wide 0.300)
(LTC DWG # 05-08-1620)
S16 (WIDE) 1098
NOTE 1
0.398 – 0.413*
(10.109 – 10.490)
16 15 14 13 12 11 10 9
12345678
0.394 – 0.419
(10.007 – 10.643)
0.037 – 0.045
(0.940 – 1.143)
0.004 – 0.012
(0.102 – 0.305)
0.093 – 0.104
(2.362 – 2.642)
0.050
(1.270)
BSC 0.014 – 0.019
(0.356 – 0.482)
TYP
0° – 8° TYP
NOTE 1
0.009 – 0.013
(0.229 – 0.330)
0.016 – 0.050
(0.406 – 1.270)
0.291 – 0.299**
(7.391 – 7.595)
× 45°
0.010 – 0.029
(0.254 – 0.737)
NOTE:
1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS
DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
*
**
S18 (WIDE) 1098
NOTE 1
0.447 – 0.463*
(11.354 – 11.760)
15 14 13 12 11 10
16
9
12345678
0.394 – 0.419
(10.007 – 10.643)
1718
0.037 – 0.045
(0.940 – 1.143)
0.004 – 0.012
(0.102 – 0.305)
0.093 – 0.104
(2.362 – 2.642)
0.050
(1.270)
BSC 0.014 – 0.019
(0.356 – 0.482)
TYP
0° – 8° TYP
NOTE 1
0.009 – 0.013
(0.229 – 0.330)
0.016 – 0.050
(0.406 – 1.270)
0.291 – 0.299**
(7.391 – 7.595)
× 45°
0.010 – 0.029
(0.254 – 0.737)
NOTE:
1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS
DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
*
**
PACKAGE DIMENSIONS
13-32
SW Package
20-Lead Plastic Small Outline (Wide 0.300)
(LTC DWG # 05-08-1620)
S24 (WIDE) 1098
NOTE 1
0.598 – 0.614*
(15.190 – 15.600)
22 21 20 19 18 17 16 15
12345678
0.394 – 0.419
(10.007 – 10.643)
910
1314
11 12
2324
0.037 – 0.045
(0.940 – 1.143)
0.004 – 0.012
(0.102 – 0.305)
0.093 – 0.104
(2.362 – 2.642)
0.050
(1.270)
BSC 0.014 – 0.019
(0.356 – 0.482)
TYP
0° – 8° TYP
NOTE 1
0.009 – 0.013
(0.229 – 0.330)
0.016 – 0.050
(0.406 – 1.270)
0.291 – 0.299**
(7.391 – 7.595)
× 45°
0.010 – 0.029
(0.254 – 0.737)
NOTE:
1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS
DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
*
**
S20 (WIDE) 1098
NOTE 1
0.496 – 0.512*
(12.598 – 13.005)
20 19 18 17 16 15 14 13
12345678
0.394 – 0.419
(10.007 – 10.643)
910
1112
0.037 – 0.045
(0.940 – 1.143)
0.004 – 0.012
(0.102 – 0.305)
0.093 – 0.104
(2.362 – 2.642)
0.050
(1.270)
BSC
0.014 – 0.019
(0.356 – 0.482)
TYP
0° – 8° TYP
NOTE 1
0.009 – 0.013
(0.229 – 0.330)
0.016 – 0.050
(0.406 – 1.270)
0.291 – 0.299**
(7.391 – 7.595)
× 45°
0.010 – 0.029
(0.254 – 0.737)
NOTE:
1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS
DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
*
**
SW Package
24-Lead Plastic Small Outline (Wide 0.300)
(LTC DWG # 05-08-1620)
PACKAGE DIMENSIONS
13-33
SW Package
28-Lead Plastic Small Outline (Wide 0.300)
(LTC DWG # 05-08-1620)
SW Package
28-Lead Plastic Small Outline Isolation Barrier (Wide 0.300)
(LTC DWG # 05-08-1690)
S28 (WIDE) 1098
0° – 8° TYP
NOTE 1
0.009 – 0.013
(0.229 – 0.330)
0.016 – 0.050
(0.406 – 1.270)
0.291 – 0.299**
(7.391 – 7.595)
× 45°
0.010 – 0.029
(0.254 – 0.737)
0.037 – 0.045
(0.940 – 1.143)
0.004 – 0.012
(0.102 – 0.305)
0.093 – 0.104
(2.362 – 2.642)
0.050
(1.270)
BSC 0.014 – 0.019
(0.356 – 0.482)
TYP
NOTE 1
0.697 – 0.712*
(17.70 – 18.08)
12345678
0.394 – 0.419
(10.007 – 10.643)
910
2526
11 12
22 21 20 19 18 17 16 152324
1413
2728
NOTE:
1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS
DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
*
**
SW28 (ISO) 1098
0° – 8° TYP
NOTE 1
0.009 – 0.013
(0.229 – 0.330)
0.016 – 0.050
(0.406 – 1.270)
0.291 – 0.299**
(7.391 – 7.595)
× 45°
0.010 – 0.029
(0.254 – 0.737)
0.005
(0.127)
RAD MIN
0.037 – 0.045
(0.940 – 1.143)
0.004 – 0.012
(0.102 – 0.305)
0.093 – 0.104
(2.362 – 2.642)
0.050
(1.270)
BSC 0.014 – 0.019
(0.356 – 0.482)
TYP
NOTE 1
0.697 – 0.712*
(17.70 – 18.08)
1234
0.394 – 0.419
(10.007 – 10.643)
2526
11 12
18 17 16 15
1413
2728
NOTE:
1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS.
DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
*
**
PACKAGE DIMENSIONS
13-34
S3 Package
3-Lead Plastic SOT-23
(LTC DWG # 05-08-1631)
S5 Package
5-Lead Plastic SOT-23
(LTC DWG # 05-08-1633)
0.95
(0.037)
REF
1.50 – 1.75
(0.059 – 0.069)
0.35 – 0.55
(0.014 – 0.022) 0.35 – 0.50
(0.014 – 0.020)
FIVE PLACES (NOTE 2)
S5 SOT-23 0599
2.80 – 3.00
(0.110 – 0.118)
(NOTE 3)
1.90
(0.074)
REF
0.90 – 1.45
(0.035 – 0.057)
0.90 – 1.30
(0.035 – 0.051)
0.00 – 0.15
(0.00 – 0.006)
0.09 – 0.20
(0.004 – 0.008)
(NOTE 2)
2.60 – 3.00
(0.102 – 0.118)
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DIMENSIONS ARE INCLUSIVE OF PLATING
3. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
4. MOLD FLASH SHALL NOT EXCEED 0.254mm
5. PACKAGE EIAJ REFERENCE IS SC-74A (EIAJ)
0.95
0.037
BSC
1.20 – 1.40
(0.047 – 0.060)
0.55
(0.022) 0.37 – 0.51
(0.015 – 0.020)
SOT-23 0599
2.80 – 3.04
(0.110 – 0.120)
1.92
0.075
BSC
0.89 – 1.12
(0.035 – 0.044)
0.013 – 0.10
(0.0005 – 0.004)
0.09 – 0.18
(0.004 – 0.007)
0.45 – 0.60
(0.017 – 0.024)
2.10 – 2.64
(0.083 – 0.104)
REF
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DIMENSIONS ARE INCLUSIVE OF PLATING
3. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
4. MOLD FLASH SHALL NOT EXCEED 0.254mm
5. JEDEC REFERENCE IS TO-236 VARIATION AB
S4 Package
4-Lead Plastic SOT-143
(LTC DWG # 05-08-1632)
S6 Package
6-Lead Plastic SOT-23
(LTC DWG # 05-08-1634)
0.95
(0.037)
REF
1.50 – 1.75
(0.059 – 0.069)
0.35 – 0.55
(0.014 – 0.022) 0.35 – 0.50
(0.014 – 0.020)
SIX PLACES (NOTE 2)
S6 SOT-23 0898
2.80 – 3.00
(0.110 – 0.118)
(NOTE 3)
1.90
(0.074)
REF
0.90 – 1.45
(0.035 – 0.057)
0.90 – 1.30
(0.035 – 0.051)
0.00 – 0.15
(0.00 – 0.006)
0.09 – 0.20
(0.004 – 0.008)
(NOTE 2)
2.6 – 3.0
(0.110 – 0.118)
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DIMENSIONS ARE INCLUSIVE OF PLATING
3. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
4. MOLD FLASH SHALL NOT EXCEED 0.254mm
5. PACKAGE EIAJ REFERENCE IS SC-74A (EIAJ)
0.37 – 0.51
(0.014 – 0.020)
NOTE 2
1.20 – 1.40
(0.047 – 0.055)
(NOTE 3)
0.55
(0.022)
REF
S4 SOT-143 0599
2.80 – 3.04
(0.110 – 0.119)
(NOTE 3)
1.92
(0.076)
BSC
0.2
(0.007)
BSC
0.89 – 1.12
(0.035 – 0.044)
0.013 – 0.100
(0.0005 – 0.004)
0.76 – 0.94
(0.029 – 0.037)
(NOTE 2)
0.09 – 0.13
(0.004 – 0.008)
(NOTE 2)
2.10 – 2.64
(0.082 – 0.104)
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DIMENSIONS ARE INCLUSIVE OF PLATING
3. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
4. MOLD FLASH SHALL NOT EXCEED 0.254mm
5. PACKAGE JEDEC REFERENCE IS TO253 VARIATION AA
PACKAGE DIMENSIONS
13-35
For Lead Bend Options See Page 13-61
ST Package
3-Lead Plastic SOT-223
(LTC DWG # 05-08-1630)
T Package
3-Lead Plastic TO-220
(LTC DWG # 05-08-1420)
0.100
(2.540)
BSC 0.028 – 0.038
(0.711 – 0.965)
T3 (TO-220) 1098
0.045 – 0.055
(1.143 – 1.397)
0.165 – 0.180
(4.191 – 4.572)
0.095 – 0.115
(2.413 – 2.921)
0.013 – 0.023
(0.330 – 0.584)
0.520 – 0.570
(13.208 – 14.478)
0.980 – 1.070
(24.892 – 27.178)
0.218 – 0.252
(5.537 – 6.401)
0.050
(1.270)
TYP
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
0.114 – 0.124
(2.90 – 3.15)
0.248 – 0.264
(6.30 – 6.71)
0.130 – 0.146
(3.30 – 3.71)
0.264 – 0.287
(6.70 – 7.30)
0.0905
(2.30)
NOM
0.033 – 0.041
(0.84 – 1.04)
0.181
(4.60)
NOM
0.024 – 0.033
(0.60 – 0.84)
0.071
(1.80)
MAX
10°
MAX
0.012
(0.31)
MIN
0.0008 – 0.0040
(0.0203 – 0.1016)
10° – 16°
0.010 – 0.014
(0.25 – 0.36)
10° – 16°
ST3 (SOT-233) 1298
PACKAGE DIMENSIONS
13-36
T Package
5-Lead Plastic TO-220 (Straight Lead)
(Nonstandard Flow 06)
(LTC DWG # 05-08-1421)
For Lead Bend Options See Page 13-61
T Package
5-Lead Plastic TO-220 (Standard)
(LTC DWG # 05-08-1421)
For Lead Bend Options See Page 13-61
0.067
(1.70)
BSC
0.028 – 0.038
(0.711 – 0.965)
T5 (TO-220)(STRAIGHT) 1098
0.045 – 0.055
(1.143 – 1.397)
0.095 – 0.115
(2.413 – 2.921)
0.013 – 0.023
(0.330 – 0.584)
0.520 – 0.570
(13.208 – 14.478)
0.980 – 1.070
(24.892 – 27.178)
0.165 – 0.180
(4.191 – 4.572)
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
T5 (TO-220) 0399
0.028 – 0.038
(0.711 – 0.965)
0.067
(1.70) 0.135 – 0.165
(3.429 – 4.191)
0.700 – 0.728
(17.78 – 18.491)
0.045 – 0.055
(1.143 – 1.397)
0.095 – 0.115
(2.413 – 2.921)
0.013 – 0.023
(0.330 – 0.584)
0.620
(15.75)
TYP
0.155 – 0.195*
(3.937 – 4.953)
0.152 – 0.202
(3.861 – 5.131)
0.260 – 0.320
(6.60 – 8.13)
0.165 – 0.180
(4.191 – 4.572)
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
BSC
SEATING PLANE
* MEASURED AT THE SEATING PLANE
PACKAGE DIMENSIONS
13-37
T7 Package
7-Lead Plastic TO-220 (Straight Lead)
(Nonstandard Flow 06)
(LTC DWG # 05-08-1422)
For Lead Bend Options See Page 13-61
For Lead Bend Options See Page 13-61
T7 Package
7-Lead Plastic TO-220 (Standard)
(LTC DWG # 05-08-1422)
0.050
(1.27)
BSC
0.520 – 0.570
(13.208 – 14.478)
0.026 – 0.036
(0.660 – 0.914)
T7 (STRAIGT) 1098
0.045 – 0.055
(1.143 – 1.397)
0.095 – 0.115
(2.41 – 2.92)
0.013 – 0.023
(0.330 – 0.584)
0.980 – 1.070
(24.892 – 27.178)
0.165 – 0.180
(4.191 – 4.572)
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
0.050
(1.27)
0.026 – 0.036
(0.660 – 0.914)
T7 (TO-220) 0399
0.135 – 0.165
(3.429 – 4.191)
0.700 – 0.728
(17.780 – 18.491)
0.045 – 0.055
(1.143 – 1.397)
0.165 – 0.180
(4.191 – 4.572)
0.095 – 0.115
(2.413 – 2.921)
0.013 – 0.023
(0.330 – 0.584)
0.620
(15.75)
TYP
0.155 – 0.195*
(3.937 – 4.953)
0.152 – 0.202
(3.860 – 5.130)
0.260 – 0.320
(6.604 – 8.128)
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
BSC
SEATING PLANE
*MEASURED AT THE SEATING PLANE
PACKAGE DIMENSIONS
13-38
W Package
10-Lead Flatpak Glass Sealed (Hermetic)
(LTC DWG # 05-08-1130)
W Package
14-Lead Flatpak Glass Sealed (Hermetic)
(LTC DWG # 05-08-1140)
DETAIL A
0.005
(0.127)
MIN
0.008 – 0.015
(0.203 – 0.381)
W10 (GLASS) 1298
0.004 – 0.006**
(0.102 – 0.152)
0.250 – 0.370
(6.350 – 9.398)
0.240 – 0.260
(6.096 – 6.604)
0.250 – 0.370
(6.350 – 9.398)
0.026 – 0.045
(0.660 – 1.143)
0.045 – 0.090
(1.14 – 2.29)
NOTES:
*THIS DIMENSION ALLOWS FOR OFF-CENTER LID, MENISCUS AND GLASS OVERRUN
**INCREASE DIMENSIONS BY 0.003 INCHES (0.076 mm) WHEN LEAD FINISH A IS APPLIED (SOLDER DIPPED)
0.005
(0.127)
MIN
0.010 – 0.019**
(0.254 – 0.483)
0.280*
(7.11)
MAX
0.300*
(7.62)
MAX
0.050
(1.270)
BSC
0.045
(1.143)
MAX
DETAIL
A
DETAIL A
W14 (GLASS) 1098
0.005
(0.127)
MIN
0.008 – 0.015
(0.203 – 0.381)
0.005
(0.127)
MIN
(4PLCS)
0.017**
(0.431)
TYP
0.385 – 0.405*
(9.779 – 10.287)
0.050
(1.270)
BSC
0.040
(1.016)
MAX
(4PLCS)
DETAIL
A
0.004 – 0.006**
( – 0.152)
0.250 – 0.370
(6.350 – 9.398)
0.245 – 0.300*
(6.223 – 7.620)
0.250 – 0.370
(6.350 – 9.398)
0.026 – 0.045
(0.660 – 1.143)
0.055 – 0.090
(1.397 – 2.286)
NOTES:
*THIS DIMENSION ALLOWS FOR OFF-CENTER LID, MENISCUS AND GLASS OVERRUN
**INCREASE DIMENSIONS BY 0.003 INCHES (0.076 mm) WHEN LEAD FINISH A IS APPLIED (SOLDER DIPPED)
PACKAGE DIMENSIONS
13-39
WB Package
10-Lead Flatpak Metal Sealed Bottom Brazed (Hermetic)
(LTC DWG # 05-08-1230)
0.005
(0.127)
MIN
0.015 – 0.019*
(0.381 – 0.483)
0.390
(9.906)
MAX
0.050
(1.27)
BSC
0.045
(1.143)
MAX
PIN 1 ID ON
BOTTOM SIDE
W14 (METAL) 1298
0.004 – 0.006*
(0.102 – 0.152)
0.250 – 0.370
(6.350 – 9.398)
0.235 – 0.260
(5.969 – 6.604)
0.250 – 0.370
(6.350 – 9.398)
0.045 – 0.115
(1.143 – 2.921)
0.125
(3.175)
MIN
0.030
(0.762)
MIN
0.030
(0.762)
MIN
0.026 – 0.045
(0.66 – 1.14)
*INCREASE DIMENSIONS BY 0.003 INCHES (0.076 mm) WHEN LEAD FINISH A IS APPLIED (SOLDER DIPPED)
WB Package
14-Lead Flatpak Metal Sealed Bottom Brazed (Hermetic)
(LTC DWG # 05-08-1240)
0.005
(0.127)
MIN
0.015 – 0.019*
(0.381 – 0.483)
0.290
(7.366)
MAX
0.050
(1.27)
BSC
0.045
(1.143)
MAX
PIN 1 ID ON
BOTTOM SIDE
W10 (METAL) 1298
0.004 – 0.006*
(0.102 – 0.152)
0.250 – 0.370
(6.350 – 9.398)
0.240 – 0.260
(6.096 – 6.604)
0.250 – 0.370
(6.350 – 9.398)
0.045 – 0.115
(1.143 – 2.921)
0.125
(3.175)
MIN
0.030
(0.762)
MIN
0.030
(0.762)
MIN
0.010
(0.254)
MIN
*INCREASE DIMENSIONS BY 0.003 INCHES (0.076 mm) WHEN LEAD FINISH A IS APPLIED (SOLDER DIPPED)
PACKAGE DIMENSIONS
13-40
Z Package
3-Lead Plastic TO-92 (Similar to TO-226)
(LTC DWG # 05-08-1410)
0.050
(1.27)
BSC
0.060 ± 0.005
(1.524± 0.127)
DIA
0.90
(2.286)
NOM
0.180 ± 0.005
(4.572 ± 0.127)
0.180 ± 0.005
(4.572 ± 0.127)
0.500
(12.70)
MIN
0.050
(1.270)
MAX
UNCONTROLLED
LEAD DIMENSION
0.016 ± 0.003
(0.406 ± 0.076)
5°
NOM
0.015 ± 0.002
(0.381 ± 0.051)
0.060 ± 0.010
(1.524 ± 0.254)
10° NOM
0.140 ± 0.010
(3.556 ± 0.127)
Z3 (TO-92) 1098
SURFACE MOUNT PRODUCTS
13-41
Introduction
Linear Technology Corporation (LTC) was founded in 1981
to address the growing demand for high performance and
superior quality linear integrated circuits.
Today, LTC has successfully established a leadership posi-
tion by introducing and supplying leading edge products in
each of the industry’s basic functional groups— op amps,
comparators, voltage regulators, references, switched-
capacitor filters, interface, data conversion, and a variety of
special function CMOS devices, in all major package styles.
Early on, LTC made the commitment to provide advanced
technology,
surface mount packaging.
This made Linear
Technology the first company to offer true precision and
high performance linear devices across the full range of
functional categories, plus many of the popular second-
source devices in JEDEC/EIAJ Standard packages:
SO (0.150) 8, 14, 16
SO (0.300) 16, 18, 20, 24, 28
SSOP (0.150) 16, 20, 24, 28
SSOP (5.3mm) 16, 20, 24, 28, 36
SSOP (7.62mm) 36, 44
TSSOP (4.4mm) 20
TSSOP (6.1mm) 48, 56
The continuing demand for more complete surface mount
designs has spurred the introduction of four power surface
mount packages by LTC : the 3-lead SOT-223, the DD pack-
age available in 3-, 5- and 7-lead versions, the SOT-23
package available in 3-, 5- and 6-lead versions and the
4-lead SOT-143. Many LTC power products are now being
introduced in these packages which, for the first time, en-
able high power designs to be realized using 100% surface
mount devices. Support for LTC’s surface mount devices
includes service for tape and reel, antistatic rails, quality
and reliability data, and data sheets on each product.
LTC intends to address customer demand for surface
mount devices where technology and die sizes permit,
making the combination of small package size and high
performance linear devices readily available to our users.
SURFACE MOUNT PRODUCTS
This section contains information summarizing LTC’s ca-
pabilities and services for surface mount packaged prod-
ucts, as well as specific device data sheets.
Package Descriptions
LTC’s SO packages conform to Standard JEDEC Small
Outline drawings.
In some instances, an LTC product available in an 8-pin
standard DIP package is offered in a 16-pin SO package.
This covers the situation where the die is too large to be
accommodated by the smaller SO-8 package. Although it is
preferable for an SO-8 device to have the same pinout as
the standard 8-pin dual-in-line version, some devices
necessitate a rotation of the die to fit in the SO-8 package.
Please refer to the applicable SO device data sheet, or
consult with the factory to verify exact pinouts for each
device.
Electrical Specifications
Wherever possible, electrical specifications for a surface
mount technology (SMT)* device are the same as the
plastic molded equivalent. Exceptions to this are identified
by the omission of the standard product electrical grade
designator from the part number.
For example:
• LT1013DS8 has the same electrical specifications
as LT1013DN8, since the “D” is common to both prod-
uct numbers.
• LT1012S8 has one or more different electrical specifica-
tions than LT1012CN8, as the “C” is missing from this
product designator suffix.
Please consult the appropriate SMT package data sheet for
complete electrical specifications.
* Terminology: SO = Small Outline, SOT = Small Outline Transistor,
SSOP = Shrink Small Outline Package, TSSOP = Thin Shrink Small
Outline Package.
LTC package code designators for SMT products are:
F = 4.4mm Body TSSOP, FW = 6.1mm Body TSSOP, G = 5.3mm Body
SSOP, GN = 0.150 Body SSOP, GW = 0.300 Body SSOP, M, Q and
R = DD Pak, S = 0.150 Body SO, SW = 0.300 Body SO, ST = SOT-223.
SURFACE MOUNT PRODUCTS
13-42
Lead Finish and Solderability
Lead finish is electroplated, lead-tin, with a low carbon
content. Solderability meets the requirements of MIL-STD-
883C, Method 2003. Recommended minimum solder pad
dimensions are given in Figure 1. (Note: Consideration
should be given to your process and power requirements.)
Figure 1. Recommended Solder Pads
Marking
Because of the limited space available for part marking on
some SMT packages, abbreviated marking codes are used
to identify the device. These codes, if used, are identified in
the individual SMT package data sheets.
F Package (4.4mm)
TSSOP-20
0.257
MIN 0.181
±0.005
0.038
±0.005
0.0256 TYP
0.0175 ±0.0015
SMP 08
NOTE: ALL DIMENSIONS ARE IN INCHES
Recommended Solder Pad Pitch and Dimensions
0.420
MIN 0.292 – 0.305
0.045
±0.005
0.0315 TYP0.0205 ±0.0025
SMP 22
NOTE: ALL DIMENSIONS ARE IN INCHES
GW Package Wide (0.300)
SSOP-36, SSOP-44
0.254
MIN 0.150 – 0.165
0.045 ±0.005
0.0165 ±0.0015 0.0250 TYP
SMP 08A
NOTE: ALL DIMENSIONS ARE IN INCHES
GN Package Narrow (0.150)
SSOP-16, SSOP-20, SSOP-24
0.321
MIN 0.212 – 0.222
0.047
±0.005
0.0256 TYP
0.0175 ±0.0015
SMP 07
NOTE: ALL DIMENSIONS ARE IN INCHES
G Package (5.3mm)
SSOP-20, SSOP-24, SSOP-28, SSOP-36
0.328
MIN 0.252 ±0.005
0.038
±0.005
0.0197 TYP
0.0132 ±0.0015
SMP 34
NOTE: ALL DIMENSIONS ARE IN INCHES
FW Package (6.1mm)
TSSOP-48, TSSOP-56
MS8 Package
8-Lead MSOP
0.206
MIN 0.126 – 0.136
0.035 ±0.005
0.0165 ±0.0015 0.0256 TYP
SMP 23
NOTE: ALL DIMENSIONS ARE IN INCHES
MS10 Package
10-Lead MSOP
0.206
MIN 0.126 – 0.136
0.035 ±0.005
0.0120 ±0.0015 0.0197 TYP
SMP 33
NOTE: ALL DIMENSIONS ARE IN INCHES
SURFACE MOUNT PRODUCTS
13-43
Figure 1. Recommended Solder Pads (Continued)
R Package
7-Lead DD
0.420
0.350
0.565
0.090
0.035
0.050
SMP 05
NOTE: ALL DIMENSIONS ARE IN INCHES
Q Package
5-Lead DD
0.420
0.350
0.565
0.090
0.042
0.067 SMP 04
NOTE: ALL DIMENSIONS ARE IN INCHES
0.420
0.350
0.565
0.090
0.070
0.100 SMP 03
NOTE: ALL DIMENSIONS ARE IN INCHES
M Package
3-Lead DD
0.325
0.205
0.080
0.565
0.090
SMP 39
NOTE: ALL DIMENSIONS ARE IN INCHES
RECOMMENDED FOR THICKER SOLDER PASTE APPLICATIONS
0.042
0.067
0.420
0.276
0.320
0.325
0.205
0.080
0.565
SMP 40
NOTE: ALL DIMENSIONS ARE IN INCHES
RECOMMENDED FOR THICKER SOLDER PASTE APPLICATIONS
0.090
0.0350.050
0.420
0.276
0.320
0.420
0.276
0.325
0.205
0.080
0.565
0.090
0.070
0.100 SMP 38
NOTE: ALL DIMENSIONS ARE IN INCHES
RECOMMENDED FOR THICKER SOLDER PASTE APPLICATIONS
0.320
SURFACE MOUNT PRODUCTS
13-44
S3 Package
3-Lead SOT-23
S4 Package
4-Lead SOT-143
S6 Package
6-Lead SOT-23
S5 Package
5-Lead SOT-23
2.74
0.764
0.96
0.8 ±0.127
SMP 24
NOTE: ALL DIMENSIONS ARE
IN MILLIMETERS
1.92
2.894
0.72
1.144
0.2 BSC
0.944
SMP 26
NOTE: ALL DIMENSIONS ARE
IN MILLIMETERS
1.92
BSC
3.254
0.754
0.95
0.854 ±0.127
SMP 31
NOTE: ALL DIMENSIONS ARE
IN MILLIMETERS
1.9
3.254
0.754
0.95
0.854 ±0.127
SMP 25
NOTE: ALL DIMENSIONS ARE
IN MILLIMETERS
1.9
T3 Package
3-Lead TO-220
(Flow 32)
T5 Package
5-Lead TO-220
(Flow 33)
T7 Package
7-Lead TO-220
(Flow 35)
Figure 1. Recommended Solder Pads (Continued)
0.570
0.420
0.800
0.067
0.042
0.080
SMP36
NOTE: ALL DIMENSIONS ARE IN INCHES
0.570
0.420
0.800
0.050
0.040
0.080
SMP37
NOTE: ALL DIMENSIONS ARE IN INCHES
0.570
0.420
0.800
0.100
0.070
0.080
SMP35
NOTE: ALL DIMENSIONS ARE IN INCHES
S Package (0.150)
SO-8, SO-14, SO-16
0.245
MIN 0.160
±0.005
0.045
±0.005
0.050 TYP0.030 ±0.005
SMP 01
NOTE: ALL DIMENSIONS ARE IN INCHES
0.129
MAX
0.059
MAX 0.248
BSC
0.090
BSC
0.181
BSC
SMP 06
0.059
MAX
0.039
MAX
NOTE: ALL DIMENSIONS ARE IN INCHES
ST Package
3-Lead SOT-223
0.420
MIN
0.325
±0.005
0.045
±0.005
0.050 TYP0.030 ±0.005
SMP 02
NOTE: ALL DIMENSIONS ARE IN INCHES
SW Package Wide (0.300)
SO-16, SO-18, SO-20, SO-24, SO-28
SURFACE MOUNT PRODUCTS
13-45
Wave and Reflow Soldering
Following are the recommended procedures for soldering
surface mount packages to PC boards.
1. Reflow Soldering
• Use of solder plating boards is recommended.
• Screen solder paste on board.
• Mount components on board.
• Infrared or forced hot air convection reflow is recom-
mended for best performance. Parameters:
– Preheat peak temperature 125°C ± 15°C and 2°C to
4°C per second rise
– Activation temperature 130°C to 150°C
– Reflow begins at 183°C (63Sn/37Pb)
– Time above 183°C for 30 seconds
– Peak package body temperature 220°C to 240°C
– Dwell time at peak temperature 10 seconds max
– Cooling rate 2°C to 4°C per second
• Clean boards.
• For Vapor Phase Reflow, recommended parameter
ranges for:
– Heating rate: 4°C per second max
– Preheat temperature: 45°C to 80°C
– Time above 200°C: 50 seconds to 90 seconds
– Peak package temperature: 212°C to 219°C
2. Wave Soldering
• Use solder plating boards.
• Dispense adhesive to hold components on board.
• Place components on board.
• Cure adhesive per adhesive manufacturer’s specifi-
cation.
• Preheat package temperature shall be between 100°C
and 130°C.
• Foam flux using RMA (Rosin Mildly Activating) flux.
• Wave solder using a dual wave soldering system at
230°C to 250°C for 2 seconds per wave.
• Clean board.
•Wave soldering is not recommended for SOT-223
package.
3. Hand Soldering
•Hand soldering of packages is not recommended.
Dry Pack in Moisture Barrier Bags
In the event of a requirement for Dry Pack, LTC employs
as a guideline the methods of IPC-SM-786A, Procedures
for Characterization of Moisture/Reflow Sensitive ICs.
Thermal Information
Table 1 shows the range of junction-to-ambient thermal
resistance of SO devices mounted on a PCB of FR4 material
with copper traces, in still air at 25°C. θ
JA
with a ceramic
substrate is about 70% of the FR4 value. Maximum power
dissipation may be calculated by the following formula:
PT
TT
DMAX A JMAX A
JA
()
=−
θ
where,
T
JMAX
= Maximum operating junction temperature.
T
A
= Desired ambient operating temperature.
θ
JA
= Junction-to-ambient thermal resistance.
Table 1. Typical Thermal Resistance Values
SO-8 150°C/W to 200°C/W SO-18 70°C/W to 100°C/W
SO-14 100°C/W to 140°C/W SO-20 70°C/W to 90°C/W
SO-16 (0.150) 90°C/W to 130°C/W SO-24 60°C/W to 80°C/W
SO-16 (0.300) 85°C/W to 100°C/W SO-28 55°C/W to 75°C/W
Conditions: PCB mount on FR4 material, still air at 25°C, copper trace.
Thermal resistance for power packages (DD and SOT-223)
depends greatly on the individual device type. Please
consult the device data sheets for thermal information.
More current data, by device type, may be obtained by
contacting LTC, Marketing Department.
Tape and Reel Packing (See Tape and Reel Section)
Plastic Tube Packing
LTC’s Surface Mount products are packed in “antistatic”
plastic tubes with the tube dimensions indicated in Figure
2. Unit quantities packaged per tube are listed below in
Table 2.
Table 2. Devices Per Tube
LTC Package LTC Package Actual Number
Code Designator Style Lead Count of Units
F TSSOP (4.4mm) 20 74
FW TSSOP (6.1mm) 48 39
FW TSSOP (6.1mm) 56 35
G SSOP (5.3mm) 16 77
G SSOP (5.3mm) 20 66
SURFACE MOUNT PRODUCTS
13-46
Table 2. Devices Per Tube (continued)
LTC Package LTC Package Actual Number
Code Designator Style Lead Count of Units
G SSOP (5.3mm) 24 59
G SSOP (5.3mm) 28 47
G SSOP (5.3mm) 36 37
GN SSOP (0.150) 16 100
GN SSOP (0.150) 20, 24 55
GW SSOP (7.62mm) 36 32
GW SSOP (7.62mm) 44 27
MS8 MSOP (0.118) 8 50
MS10 MSOP (0.118) 10 50
Figure 2
0.280
0.060
0.205
0.063±0.007
0.055±0.005
NOTE: ALL DIMENSIONS ARE IN INCHES, ±0.010 UNLESS OTHERWISE SPECIFIED
MATERIAL: ANITSTATIC TREATED RIGID TRANSPARENT PVC OR RIGID BLACK CONDUCTIVE
PRINTING: “LTC LOGO, LINEAR TECHNOLOGY CORP., ANTISTATIC” ON TOPSIDE OF TUBE
LENGTH: 20.75 +1/32
–1/16
0.300 0.310
0.375
±0.005 0.580
SMP 10
SW (0.300)
SO Package Shipping Tube
0.105
0.20±0.005 R 0.020
×4, REF
0.150 0.140
0.026 0.048 +0.010
–0.005
0.142
0.340
SMP 11
NOTE: ALL DIMENSIONS ARE IN INCHES
ST
SOT-223 Package Shipping Tube
M, Q, R DD 3, 5, 7 50
S8 S8 (0.150) 8 100
S S (0.150) 14 55
S S (0.150) 16 50
ST SOT-223 3 78
SW SW (0.300) 16 47
SW SW (0.300) 18 40
SW SW (0.300) 20 38
SW SW (0.300) 24 32
SW SW (0.300) 28 27
PLASTIC TUBE SPECIFICATIO S
U
S (0.150)
SO Package Shipping Tube
MSOP
MS8 Package Shipping Tube
3.15 ±0.1
9.0
NOTE: ALL DIMENSIONS ARE IN MILLIMETERS
TYP RADIUS: 0.2
MATERIAL THICKNESS: 0.6
MSOP 8LD POLYCARBONATE TUBE TO BE ANTISTATIC
COMPLIANT PER LTC SPEC 01-99-0001
1.05
1.5 REF
1.3 REF
+0.05
–0.05
0.75+0.00
–0.10 1.35+0.10
–0.00
R0.4
2.45
3.65
3.6
SMP 27
0.170
REF
0.265
0.155
0.315
REF
SMP 09
0.070
0.025 ± 0.005
WALL
NOTE: ALL DIMENSIONS ARE IN INCHES
LENGTH: 20.50 +1/16
–1/32
SURFACE MOUNT PRODUCTS
13-47
SOT-23 (Codes: S3, S5 or S6)
FUNCTION CIRCUITS AVAILABLE
References LT1460HCS3-x.x
LT1460JCS3-x.x
LT1460KCS3-x.x
Regulators LTC1517CS5-3.3
LTC1517CS5-5
LT1611CS5
LT1613CS5
SMBus Accelerator LTC1694CS5
SOT-223 (Code: ST)
FUNCTION CIRCUITS AVAILABLE
Linear Regulators LT1117CST
LT1117CST-x.xx
LT1118CST-x.xx
LT1121CST-x.x*
LT1123CST
LT1129CST-x.x*
LT1175CST-5*
LT1521CST-x.x*
MSOP-8 (Code: MS8)
FUNCTION CIRCUITS AVAILABLE
Operational Amplifiers LT1351CMS8
LT1490CMS8
LTC1541CMS8
LTC1542CMS8
LT1636CMS8
LT1638CMS8
Current Sense Amp LT1620CMS8
Comparators LT1394CMS8
LTC1440CMS8
LTC1540CMS8
LTC1541CMS8
LTC1542CMS8
LT1671CMS8
LT1720CMS8
References LTC1258CMS8-2.5
LT1460CCMS8-xx.x
LT1460FCMS8-xx.x
LT1634BCMS8-x.xx
D/A Converters LTC1426CMS8
LTC1658CMS8*
LTC1659CMS8
LTC1661CMS8*
Micropackage Products, SOT-23, SOT-223, MSOP, SSOP-16
A/D Converters LTC1197LCMS8
LTC1199LCMS8
IrDA Receiver LT1328CMS8
EIA485 Transceivers LTC1482CMS8
LTC1484CMS8
LTC1690CMS8
Dual MOSFET Drivers LTC1693-3CMS8
Linear Regulators LT1521CMS8
LT1521CMS8-x.x
Charge Pump DC/DC LTC1522CMS8
LTC1682CMS8
LTC1682CMS8-x.x
Sw. Cap. Inverters LTC1261LCMS8
LTC1261LCMS8-x.x
LTC1550LCMS8
LTC1550LCMS8-x.x
LTC1551LCMS8
LTC1551LCMS8-4.1
Switching Regulators LT1307BMS8
LT1307CMS8
LT1316CMS8
LT1317BCMS8
LT1317CMS8
LTC1474CMS8
LTC1474CMS8-x.x
LTC1475CMS8
LTC1475CMS8-x.x
LT1610CMS8
LT1614CMS8
LTC1622CMS8
Triple Supply Monitors LTC1326CMS8
LTC1326CMS8-2.5
LTC1536CMS8
Varactor Driver LTC1340CMS8
SMBus Switch Drivers LTC1623CMS8
LTC1710CMS8
SSOP-16 (Code: G OR GN)
FUNCTION CIRCUITS AVAILABLE
Current Feedback Amp LT1395CGN
Current Sense Amps LT1620IGN
LT1620CGN
LT1621CGN*
D/A Converters LTC1660CGN*
LTC1665CGN
A/D Converters LTC1417ACGN
LTC1417CGN
Filters LTC1067-50CGN*
LTC1067CGN*
RGB MUX with CFAs LT1675CGN
Multiplexers LTC1380CGN*
LTC1393CGN*
Dual Switch Drivers LTC1473CGN*
Hot Swap Controllers LTC1643HCGN*
LTC1643LCGN*
Linear Regulators LT1579CGN
LT1579CGN-x.x
SIM Power Supply LTC1555CGN*
Backup Battery Ctlrs LTC1558CGN-3.3
LTC1558CGN-5
LTC1559CGN-3.3
LTC1559CGN-5
Battery Chargers LT1510-5CGN*
LT1510CGN*
LT1512CGN*
SIM Power Supply LTC1556CGN
Switch Cap. Inverter LTC1550CGN*
LTC1550LCGN*
Switching Regulators LTC1430ACGN*
LTC1433CGN*
LTC1434CGN*
LTC1435ACG*
LTC1435CG*
LTC1473LCGN
LTC1625CGN*
LTC1735CGN*
* Industrial temperature tested versions also available
SURFACE MOUNT PRODUCTS
13-48
by package type and full part number. The designator “LT”
may be either the stylized LT logo or block sans serif type
depending on marking method used.
Due to the limited amount of space availiable for marking,
LTC surface mount devices of 8 leads and less are marked
with an abbreviated code. This is a listing of these codes
8-Lead MSOP
MARK FULL PART NUMBER
LTAA LT1460CCMS8-2.5
LTAB LT1460FCMS8-2.5
LTAF LT1460CCMS8-5
LTAG LT1460FCMS8-5
LTAH LT1460CCMS8-10
LTAJ LT1460FCMS8-10
LTBA LTC1326CMS8
LTBB LT1490CMS8
LTBC LT1620CMS8
LTBE LTC1541CMS8
LTBF LT1307BCMS8
LTBG LT1328CMS8
LTBH LT1394CMS8
LTBJ LT1394IMS8
LTBK LTC1475CMS8
LTBL LTC1197LCMS8
LTBM LTC1340CMS8
LTBN LT1634ACMS8-1.25
LTBQ LTC1426CMS8
LTBT LT1351CMS8
LTBU LT1307CMS8
LTBV LTC1536CMS8
LTBW LTC1474CMS8
LTBX LTC1440CMS8
LTBY LTC1440IMS8
LTBZ LTC1317CMS8
LTCB LTC1482CMS8
LTCC LTC1482IMS8
LTCD LTC1316CMS8
LTCE LTC1540CMS8
LTCF LTC1258CMS8-2.5
LTCG LTC1522CMS8
LTCH LTC1623CMS8
LTCK LTC1659CMS8
LTCL LT1636CMS8
LTCM LTC1199LCMS8
LTCP LTC1475CMS8-3.3
LTCQ LTC1475CMS8-5
LTCR LTC1474CMS8-3.3
LTCS LTC1474CMS8-5
LTCT LT1671CMS8
LTCU LTC1671MS8
LTCV LT1634BCMS8-1.25
LTCW LTC1658CMS8
LTCY LT1638CMS8
LTCZ LTC1474IMS8
LTDA LTC1690CMS8
LTDB LTC1622CMS8
LTDC LTC1622IMS8
LTDD LT1634ACMS8-2.5
LTDE LTC1542CMS8
LTDF LT1634BCMS8-2.5
LTDG LT1634ACMS8-4.096
LTDH LT1634BCMS8-4.096
LTDJ LT1634ACMS8-5
LTDK LT1634BCMS8-5
LTDL LT1317BCMS8
LTDM LT1121CMS8-3.3
LTDN LT1389BCMS8-1.25
LTDP LT1389BCMS8-2.5
LTDQ LT1389BCMS8-4.096
LTDR LT1389BCMS8-5
LTDS LT1720CMS8
LTDT LT1610CMS8
LTDU LT1521CMS8-3.3
LTDV LTC1661CMS8
LTDW LTC1661IMS8
LTDX LTC1484CMS8
LTDY LT1396CMS8
LTDZ LTC1710CMS8
LTEA LT1317BMS8
LTEB LTC1693-3CMS8
LTEC LTC1502CMS8-3.3
LTEG LTC1550LCMS8
LTEH LTC1550LCMS8-4.1
LTEJ LT1614CMS8
LTEK LTC1326CMS8-2.5
LTEL LTC1258CMS8
LTEM LTC1258CMS8-5
LTEN LTC1258CMS8-4.1
LTEQ LTC1663CMS8
LTER LT1682CMS8
LTEU LTC1258CMS8-3.0
LTEZ LT1521CMS8
LTFA LT1521CMS8-5
LTFB LT1521CMS8-3
LTFC LT1197CMS8
LTFD LTC1550LIMS8
LTFE LTC1550LIMS8-4.1
LTFF LT1494CMS8
LTFG LT1494IMS8
LTFH LT1672CMS8
LTFJ LT1672IMS8
LTFL LTC1199CMS8
LTFM LTC1261LCMS8
LTFN LTC1261LCMS8-4
LTFP LTC1261LCMS8-4.5
LTFQ LTC1551LCMS8
LTFR LTC1551LCMS8-2
LTFS LTC1551LCMS8-2.5
LTFT LTC1551LCMS8-4.1
LTFU LTC1550LCMS8-2
LTFV LTC1550LCMS8-2.5
LTFW LTC1658IMS8
LTFX LTC1503CMS8-1.8
LTFY LTC1503IMS8-1.8
LTFZ LTC1503CMS10
LTGA LTC1503IMS10
LTGR LTC1550LCMS8-2
LTGS LT1610IMS8
LTGT LTC1682CMS8-3.3
LTGU LTC1682IMS8-3.3
LTGV LTC1682CMS8-5
LTGW LTC1682IMS8-5
LTGX LT1675CMS8-1
LTGY LT1675IMS8-1
LTHB LT1317BCMS8
LTHL LTC1502IMS8-3.3
10-Lead MSOP
MARK FULL PART
NUMBER
LTFZ LTC1503CMS10
LTGA LTC1503IMS10
8-Lead SO
MARK FULL PART NUMBER
0412 LT1004CS8-1.2
0412I LT1004IS8-1.2
0425 LT1004CS8-2.5
0425I LT1004IS8-2.5
04AI33 LTC1504AIS8-3.3
1001 LT1001CS8
1006 LT1006S8
1007 LT1007CS8
1007I LT1007IS8
1008 LT1008S8
1009 LT1009S8
1009I LT1009IS8
1011 LT1011CS8
1012 LT1012S8
1013 LT1013DS8
1013I LT1013IS8
1016 LT1016CS8
1016I LT1016IS8
1017 LT1017CS8
1017I LT1017IS8
1018 LT1018CS8
1026 LT1026CS8
1026I LT1026IS8
1027C5 LT1027CCS8-5
1027D5 LT1027DCS8-5
1027E5 LT1027ECS8-5
1028 LT1028CS8
1034I12 LT1034IS8-1.2
1037 LT1037CS8
1041 LTC1041CS8
1044 LTC1044CS8
1044/R LTC1044CS8/R
1044A LTC1044ACS8
1044AI LTC1044AIS8
1046 LTC1046CS8
1046I LTC1046IS8
1049 LTC1049CS8
1050 LTC1050CS8
1054 LT1054CS8
1054A LT1054ACS8
1054I LT1054IS8
1054L LT1054LCS8
1055 LT1055S8
1056 LT1056S8
1057 LT1057S8
1057I LT1057IS8
10691 LTC1069-1CS8
10691I LTC1069-1IS8
10696 LTC1069-6CS8
10696I LTC1069-6IS8
10697 LTC1069-7CS8
10697I LTC1069-7IS8
1072 LT1072CS8
1073 LT1073CS8
10731 LT1073CS8-12
10735 LT1073CS8-5
1077 LT1077S8
1077I LT1077IS8
1078 LT1078S8
1078I LT1078IS8
10905 LT1109CS8-5
10912 LT1109CS8-12
1096 LTC1096CS8
1096A LTC1096ACS8
1096AI LTC1096AIS8
1096I LTC1096IS8
1096L LTC1096LCS8
1096LI LTC1096LIS8
1097 LT1097S8
1098 LTC1098CS8
1098A LTC1098ACS8
1098AI LTC1098AIS8
1098I LTC1098IS8
1098L LTC1098LCS8
1098LI LTC1098LIS8
11012 LT1110CS8-12
1107 LT1107CS8
110712 LT1107CS8-12
11075 LT1107CS8-5
1107I LT1107IS8
1108 LT1108CS8
11081 LT1108CS8-12
11085 LT1108CS8-5
1109 LT1109CS8
1109A LT1109ACS8
1109A1 LT1109ACS8-12
1109A5 LT1109ACS8-5
1110 LT1110CS8
11105 LT1110CS8-5
1111 LT1111CS8
11111 LT1111CS8-12
11115 LT1111CS8-5
1111I LT1111IS8
1112 LT1112S8
1113 LT1113CS8
1116 LT1116CS8
1118 LT1118CS8
111825 LT1118CS8-2.5
111828 LT1118CS8-2.85
11185 LT1118CS8-5
1120 LT1120CS8
1120A LT1120ACS8
1120AI LT1120AIS8
1121 LT1121CS8
11213 LT1121CS8-3.3
11215 LT1121CS8-5
1121A LT1121ACS8
1121A3 LT1121ACS8-3.3
1121A5 LT1121ACS8-5
1121I LT1121IS8
1122C LT1122CS8
1122D LT1122DS8
11232 LTC1123CS8-2.85
1124 LT1124CS8
1126 LT1126CS8
1128 LT1128CS8
1129 LT1129CS8
11293 LT1129CS8-3.3
11295 LT1129CS8-5
1129I LT1129IS8
1129I3 LT1129IS8-3.3
1129I5 LT1129IS8-5
1144 LTC1144CS8
1144I LTC1144IS8
11473 LTC1147CS8-3.3
SURFACE MOUNT PRODUCTS
13-49
11475 LTC1147CS8-5
1147I3 LTC1147IS8-3.3
1147L LTC1147LCS8
1147L3 LTC1147LCS8-3.3
1147LI LTC1147LIS8
1150 LTC1150CS8
1152 LTC1152CS8
1152I LTC1152IS8
1153 LTC1153CS8
1153I LTC1153IS8
1154 LTC1154CS8
1155 LTC1155CS8
1155I LTC1155IS8
1157 LTC1157CS8
1163 LTC1163CS8
1165 LTC1165CS8
1166 LT1166CS8
1167 LT1167CS8
1167A LT1167ACS8
1167AI LT1167AIS8
1167I LT1167IS8
1169 LT1169CS8
1172 LT1172CS8
1172HI LT1172HVIS8
1172I LT1172IS8
1173 LT1173CS8
117312 LT1173CS8-12
11735 LT1173CS8-5
1174 LTC1174CS8
117433 LTC1174CS8-3.3
117450 LTC1174CS8-5
1174H LTC1174HVCS8
1174H3 LTC1174HVCS8-3.3
1174H5 LTC1174HVCS8-5
1174HI LTC1174HVIS8
1174I LTC1174IS8
1175 LT1175CS8
11755 LT1175CS8-5
1175I LT1175IS8
1175I5 LT1175IS8-5
1178 LT1178S8
1187 LT1187CS8
1189 LT1189CS8
1190 LT1190CS8
1191 LT1191CS8
1192 LT1192CS8
1193 LT1193CS8
1194 LT1194CS8
1195 LT1195CS8
11961A LTC1196-1ACS8
11961B LTC1196-1BCS8
11962A LTC1196-2ACS8
11962B LTC1196-2BCS8
1197 LTC1197CS8
1197I LTC1197IS8
1197L LTC1197LCS8
1197LI LTC1197LIS8
11981A LTC1198-1ACS8
11981B LTC1198-1BCS8
11982A LTC1198-2ACS8
11982B LTC1198-2BCS8
1199 LTC1199CS8
1199I LTC1199IS8
1199L LTC1199LCS8
1199LI LTC1199LIS8
1200 LT1200CS8
1201 LT1201CS8
1203 LT1203CS8
1206 LT1206CS8
1208 LT1208CS8
1211 LT1211CS8
1211I LT1211IS8
1213 LT1213CS8
1215 LT1215CS8
1217 LT1217CS8
1218 LT1218CS8
1218L LT1218LCS8
1219 LT1219CS8
1219L LT1219LCS8
121AI LT1121AIS8
121AI3 LT1121AIS8-3.3
121AI5 LT1121AIS8-5
121I3 LT1121IS8-3.3
121I5 LT1121IS8-5
1220 LT1220CS8
1221 LT1221CS8
1222 LT1222CS8
1222I LT1222IS8
1223 LT1223CS8
1224 LT1224CS8
1225 LT1225CS8
1226 LT1226CS8
1227 LT1227CS8
1228 LT1228CS8
1229 LT1229CS8
1232 LTC1232CS8
1232I LTC1232IS8
1234 LTC1234CS8
1241 LT1241CS8
1241I LT1241IS8
1242 LT1242CS8
1242I LT1242IS8
1243 LT1243CS8
1243I LT1243IS8
1244 LT1244CS8
1244I LT1244IS8
1245 LT1245CS8
1245I LT1245IS8
1246 LT1246CS8
1247 LT1247CS8
1249 LT1249CS8
1249I LT1249IS8
1250 LTC1250CS8
1252 LT1252CS8
1253 LT1253CS8
1255 LTC1255CS8
1255I LTC1255IS8
1257 LTC1257CS8
1257I LTC1257IS8
1258 LTC1258CS8
12582 LTC1258CS8-2.5
12583 LTC1258CS8-3.0
125841 LTC1258CS8-4.1
12585 LTC1258CS8-5
1261 LTC1261CS8
12614 LTC1261CS8-4
126145 LTC1261CS8-4.5
1261L LTC1261LCS8
1261L4 LTC1261LCS8-4
1262 LTC1262CS8
1262I LTC1262IS8
1263 LTC1263CS8
1285 LTC1285CS8
12853 LTC1285CS-3.0
1285I LTC1285IS8
1286 LTC1286CS8
1286I LTC1286IS8
1288 LTC1288CS8
1288I LTC1288IS8
1298 LTC1298CS8
1298I LTC1298IS8
1300 LT1300CS8
1301 LT1301CS8
1301I LT1301IS8
1302 LT1302CS8
13025 LT1302CS8-5
1303 LT1303CS8
13035 LT1303CS8-5
1303I LT1303IS8
1303I5 LT1303IS8-5
1304 LT1304CS8
130433 LT1304CS8-3.3
13045 LT1304CS8-5
1305 LT1305CS8
1307 LT1307CS8
1307B LT1307BCS8
1307BI LT1307BIS8
1307I LT1307IS8
1308 LT1308CS8
1308I LT1308IS8
1309 LT1309CS8
1312 LT1312CS8
1316 LT1316CS8
1316I LT1316IS8
1317 LT1317CS8
1317B LT1317BCS8
1317BI LT1317BIS8
1317I LT1317IS8
1326 LTC1326CS8
132625 LTC1326CS8-2.5
1326I LTC1326IS8
1328 LT1328CS8
1328I LT1328IS8
13291 LTC1329CS8-10
13295 LTC1329CS8-50
1329A5 LTC1329ACS8-50
1329I5 LTC1329IS8-50
1340 LTC1340CS8
1351 LT1351CS8
1352 LT1352CS8
1354 LT1354CS8
1355 LT1355CS8
1357 LT1357CS8
1358 LT1358CS8
1360 LT1360CS8
1361 LT1361CS8
1363 LT1363CS8
1364 LT1364CS8
1366 LT1366CS8
1366I LT1366IS8
1368 LT1368CS8
1372 LT1372CS8
1372H LT1372HVCS8
1372HI LT1372HVIS8
1372I LT1372IS8
1373 LT1373CS8
1373H LT1373HVCS8
1373HI LT1373HVIS8
1373I LT1373IS8
1374 LT1374CS8
13745 LT1374CS8-5
1374HV LT1374HVCS8
1374I LT1374IS8
1374I5 LT1374IS8-5
1374SN LT1374CS8-SYNC
1375 LT1375CS8
13755 LT1375CS8-5
1375HV LT1375HVCS8
1375I LT1375IS8
1375I5 LT1375IS8-5
1376 LT1376CS8
13765 LT1376CS8-5
1376HV LT1376HVCS8
1376I LT1376IS8
1376I5 LT1376IS8-5
1377 LT1377CS8
1377I LT1377IS8
1389B4 LT1389BCS8-4.096
1389B5 LT1389BCS8-5
1392 LTC1392CS8
1392I LTC1392IS8
1394 LT1394CS8
1394I LT1394IS8
1400 LTC1400CS8
1400I LTC1400IS8
1401 LTC1401CS8
1401I LTC1401IS8
1404 LTC1404CS8
1404I LTC1404IS8
1413 LT1413S8
1422 LTC1422CS8
1422I LTC1422IS8
14245 LT1424CS8-5
14249 LT1424CS8-9
1424I5 LT1424IS8-5
1424I9 LT1424IS8-9
1426 LTC1426CS8
1426I LTC1426IS8
142750 LTC1427CS8-50
142850 LTC1428CS8-50
14294 LTC1429CS8-4
1430 LTC1430CS8
1430A LTC1430ACS8
1430I LTC1430IS8
1431 LT1431CS8
1431I LT1431IS8
1432 LT1432CS8
14323 LT1432CS8-3.3
1440 LTC1440CS8
1440I LTC1440IS8
1441 LTC1441CS8
1441I LTC1441IS8
1442 LTC1442CS8
1442I LTC1442IS8
1446 LTC1446CS8
1446I LTC1446IS8
1446L LTC1446LCS8
1446LI LTC1446LIS8
1448 LTC1448CS8
1448I LTC1448IS8
1451 LTC1451CS8
1451I LTC1451IS8
1452 LTC1452CS8
1452I LTC1452IS8
1453 LTC1453CS8
1453I LTC1453IS8
1456 LTC1456CS8
1456I LTC1456IS8
1457 LT1457S8
1460A1 LT1460ACS8-10
1460A2 LT1460ACS8-2.5
1460A5 LT1460ACS8-5
1460D1 LT1460DCS8-10
1460D2 LT1460DCS8-2.5
1460D5 LT1460DCS8-5
1462 LT1462CS8
SURFACE MOUNT PRODUCTS
13-50
1462A LT1462ACS8
1464 LT1464CS8
1464A LT1464ACS8
1466L LT1466LCS8
1468 LT1468CS8
1468I LT1468IS8
1470 LTC1470CS8
1474 LTC1474CS8
147433 LTC1474CS8-3.3
14745 LTC1474CS8-5
1474I LTC1474IS8
1474I5 LTC1474IS8-5
1475 LTC1475CS8
147533 LTC1475CS8-3.3
14755 LTC1475CS8-5
1475I LTC1475IS8
1477 LTC1477CS8
1480 LTC1480CS8
1480I LTC1480IS8
1481 LTC1481CS8
1481I LTC1481IS8
1482 LTC1482CS8
1482I LTC1482IS8
1483 LTC1483CS8
1483I LTC1483IS8
1484 LTC1484CS8
1484I LTC1484IS8
1485 LTC1485CS8
1485I LTC1485IS8
1487 LTC1487CS8
1487I LTC1487IS8
1490 LT1490CS8
1490I LT1490IS8
1492 LT1492CS8
1495 LT1495CS8
1495I LT1495IS8
1497 LT1497CS8
1498 LT1498CS8
1501 LT1501CS8
150133 LT1501CS8-3.3
15015 LT1501CS8-5
1501I LT1501IS8
1501I3 LT1501IS8-3.3
1501I5 LT1501IS8-5
150233 LTC1502CS8-3.3
1504 LTC1504CS8
150433 LTC1504CS8-3.3
1504A LTC1504ACS8
1504AI LTC1504AIS8
1504I LTC1504IS8
1504I3 LTC1504IS8-3.3
1506 LT1506CS8
150633 LT1506CS8-3.3
1506I LT1506IS8
1507 LT1507CS8
15073 LT1507CS8-3.3
1507I LT1507IS8
1507I3 LT1507IS8-3.3
1510 LT1510CS8
1510I LT1510IS8
1512 LT1512CS8
1512I LT1512IS8
15143 LTC1514CS8-3
151433 LTC1514CS8-3.3
15145 LTC1514CS8-5
1514I3 LTC1514IS8-3
1514I5 LTC1514IS8-5
1515 LTC1515CS8
151535 LTC1515CS8-3/5
1515I LTC1515IS8
1516 LTC1516CS8
1516I LTC1516IS8
1521 LT1521CS8
15213 LT1521CS8-3
152133 LT1521CS8-3.3
15215 LT1521CS8-5
1521I LT1521IS8
1521I3 LT1521IS8-3
1521I33 LT1521IS8-3.3
1521I5 LT1521IS8-5
1522 LTC1522CS8
1522I LTC1522IS8
1530 LTC1530CS8
153019 LTC1530CS8-1.9
153025 LTC1530CS8-2.5
153028 LTC1530CS8-2.8
153033 LTC1530CS8-3.3
1530I LTC1530IS8
1536 LTC1536CS8
1536I LTC1536IS8
1540 LTC1540CS8
1540I LTC1540IS8
1541 LTC1541CS8
1541I LTC1541IS8
1542 LTC1542CS8
1542I LTC1542IS8
155041 LTC1550CS8-4.1
1550L LTC1550LCS8
1550L2 LTC1550LCS8-2
155141 LTC1551CS8-4.1
1551L LTC1551LCS8
1551L2 LTC1551LCS8-2
155833 LTC1558CS8-3.3
15585 LTC1558CS8-5
155933 LTC1559CS8-3.3
15595 LTC1559CS8-5
15601 LTC1560-1CS8
15601I LTC1560-1IS8
1573 LT1573CS8
157325 LT1573CS8-2.5
157328 LT1573CS8-2.8
157333 LT1573CS8-3.3
1573I LT1573IS8
1575 LT1575CS8
157515 LT1575CS8-1.5
157528 LT1575CS8-2.8
157533 LT1575CS8-3.3
157535 LT1575CS8-3.5
15755 LT1575CS8-5
1576 LT1576CS8
1576I LT1576IS8
1576SN LT1576CS8-SYNC
1579 LT1579CS8
15793 LT1579CS8-3
157933 LT1579CS8-3.3
15795 LT1579CS8-5
1595A LTC1595ACS8
1595AI LTC1595AIS8
1595B LTC1595BCS8
1595BI LTC1595BIS8
1595C LTC1595CCS8
1595CI LTC1595CIS8
15I335 LTC1515IS8-3.3/5
1610 LT1610CS8
1610I LT1610IS8
1614 LT1614CS8
1614I LT1614IS8
1619 LT1619CS8
1619I LT1619IS8
1620 LT1620CS8
1620I LT1620IS8
1622 LTC1622CS8
1623 LTC1623CS8
1623I LTC1623IS8
1624 LTC1624CS8
1624I LTC1624IS8
1627 LTC1627CS8
1627I LTC1627IS8
1630 LT1630CS8
1632 LT1632CS8
1634A1 LT1634ACS8-1.25
1634A2 LT1634ACS8-2.5
1634A4 LT1634ACS8-4.096
1634A5 LT1634ACS8-5
1634B1 LT1634BCS8-1.25
1634B2 LT1634BCS8-2.5
1634B4 LT1634BCS8-4.096
1634B5 LT1634BCS8-5
1635 LT1635CS8
1635I LT1635IS8
1636 LT1636CS8
1636I LT1636IS8
1638 LT1638CS8
1638I LT1638IS8
1640H LT1640HCS8
1640HI LT1640HIS8
1640L LT1640LCS8
1640LI LT1640LIS8
1641 LT1641CS8
16471 LTC1647-1CS8
16472 LTC1647-2CS8
1655 LTC1655CS8
1655I LTC1655IS8
1658 LTC1658CS8
1658I LTC1658IS8
1659 LTC1659CS8
1659I LTC1659IS8
1671 LT1671CS8
1671I LT1671IS8
16751 LT1675-1CS8
1675I1 LT1675-1IS8
1676 LT1676CS8
1676I LT1676IS8
168233 LTC1682CS8-3.3
16825 LTC1682CS8-5
1682I5 LTC1682IS8-5
1685 LTC1685CS8
1686 LTC1686CS8
1690 LTC1690CS8
1690I LTC1690IS8
16931 LTC1693-1CS8
16932 LTC1693-2CS8
170619 LTC1706CS8-19
1710 LTC1710CS8
1710I LTC1710IS8
1719 LTC1719CS8
1719I LTC1719IS8
1720 LT1720CS8
1720I LT1720IS8
1763 LT1763CS8
1776 LT1776CS8
1776I LT1776IS8
1785 LT1785CS8
1785I LT1785IS8
1787 LT1787CS8
1787I LT1787IS8
1813 LT1813CS8
1841 LTC1841CS8
1841I LTC1841IS8
1842 LTC1842CS8
1842I LTC1842IS8
1843 LTC1843CS8
1843I LTC1843IS8
1864 LTC1864CS8
1864I LTC1864IS8
1865 LTC1865CS8
1865I LTC1865IS8
1905 LT1019CS8-5
1910 LT1019CS8-10
1925 LT1019CS8-2.5
1945 LT1019CS8-4.5
2078 LT2078CS8
2078A LT2078ACS8
2078AI LT2078AIS8
2078I LT2078IS8
2105 LT1021DCS8-5
2107 LT1021DCS8-7
2110 LT1021DCS8-10
2178 LT2178CS8
2178A LT2178ACS8
2178AI LT2178AIS8
2178I LT2178IS8
234 LM234S8
236AC1 LT1236ACS8-10
236AC5 LT1236ACS8-5
236AI1 LT1236AIS8-10
236AI5 LT1236AIS8-5
236BC1 LT1236BCS8-10
236BC5 LT1236BCS8-5
236BI1 LT1236BIS8-10
236BI5 LT1236BIS8-5
236CC1 LT1236CCS8-10
236CC5 LT1236CCS8-5
236CI5 LT1236CIS8-5
236I1 LT1236CIS8-10
2400 LTC2400CS8
2400I LTC2400IS8
261L45 LTC1261LCS8-4.5
2851 LM285S8-1.2
2852 LM285S8-2.5
318 LM318S8
326I25 LTC1326IS8-2.5
334 LM334S8
3401 LT1034CS8-1.2
3402 LT1034CS8-2.5
34I02 LT1034IS8-2.5
3745SN LT1374CS8-5 SYNC
374HVI LT1374HVIS8
374ISN LT1374IS8-SYNC
375HVI LT1375HVIS8
376HVI LT1376HVIS8
3851 LM385S8-1.2
3851B LM385BS8-1.2
3852 LM385S8-2.5
3852 B LM385BS8-2.5
389A12 LT1389ACS8-1.25
389B12 LT1389BCS8-1.25
389B25 LT1389BCS8-2.5
398 LF398S8
460BI1 LT1460BIS8-10
460BI2 LT1460BIS8-2.5
460BI5 LT1460BIS8-5
460EI1 LT1460EIS8-10
460EI2 LT1460EIS8-2.5
460EI5 LT1460EIS8-5
460LH5 LT1460LHS8-5
460MH5 LT1460MHS8-5
474I33 LTC1474IS8-3.3
485 LTC485CS8
485I LTC485IS8
SURFACE MOUNT PRODUCTS
13-51
490 LTC490CS8
490I LTC490IS8
502I33 LTC1502IS8-3.3
504A33 LTC1504ACS8-3.3
506I33 LT1506IS8-3.3
514I33 LTC1514IS8-3.3
515335 LTC1515CS8-3.3/5
515I35 LTC1515IS8-3/5
530I19 LTC1530IS8-1.9
530I25 LTC1530IS8-2.5
530I28 LTC1530IS8-2.8
530I33 LTC1530IS8-3.3
550L25 LTC1550LCS8-2.5
550L41 LTC1550LCS8-4.1
551L25 LTC1551LCS8-2.5
551L41 LTC1551LCS8-4.1
573I25 LT1573IS8-2.5
573I28 LT1573IS8-2.8
573I33 LT1573IS8-3.3
576ISN LT1576IS8-SYNC
60LH25 LT1460LHS8-2.5
60MH25 LT1460MHS8-2.5
634AI1 LT1634AIS8-1.25
634AI2 LT1634AIS8-2.5
634AI4 LT1634AIS8-4.096
634AI5 LT1634AIS8-5
634BI1 LT1634BIS8-1.25
634BI2 LT1634BIS8-2.5
634BI4 LT1634BIS8-4.096
634BI5 LT1634BIS8-5
660 LTC660CS8
682I33 LTC1682IS8-3.3
690 LTC690CS8
690I LTC690IS8
692 LTC692CS8
692I LTC692IS8
694 LTC694CS8
6943 LTC694CS8-3.3
694I LTC694IS8
694I3 LTC694IS8-3.3
699 LTC699CS8
699I LTC699IS8
706I19 LTC1706IS8-19
74I5SN LT1374IS8-5 SYNC
8043E LTC8043ES8
8043F LTC8043FS8
941I LT941IS8
947 LTC947CS8
954 LT954CS8
OP07 OP07CS8
OP27G OP27GS8
OP37G OP37GS8
SOT-223
MARK FULL PART NUMBER
1117 LT1117CST
11172 LT1117CST-2.85
11173 LT1117CST-3.3
11175 LT1117CST-5
111825 LT1118CST-2.5
111828 LT1118CST-2.85
11185 LT1118CST-5
11213 LT1121CST-3.3
11215 LT1121CST-5
1121I5 LT1121IST-5
1123 LT1123CST
11293 LT1129CST-3.3
11295 LT1129CST-5
11755 LT1175CST-5
1175I5 LT1175IST-5
121I3 LT1121IST-3.3
121I5 LT1121IST-5
129I3 LT1129IST-3.3
129I5 LT1129IST-5
15213 LT1521CST-3
152133 LT1521CST-3.3
15215 LT1521CST-5
1521I3 LT1521IST-3
1521I33 LT1521IST-3.3
1521I5 LT1521IST-5
3-Lead SOT-23
MARK FULL PART NUMBER
LTAC LT1460HCS3-2.5
LTAD LT1460JCS3-2.5
LTAE LT1460KCS3-2.5
LTAK LT1460HCS3-5
LTAL LT1460JCS3-5
LTAM LT1460KCS3-5
LTAN LT1460HCS3-10
LTAP LT1460JCS3-10
LTAQ LT1460KCS3-10
LTAR LT1460DIS3-5
LTAU LT1460CCS3-10
LTAV LT1460DCS3-10
LTAY LT1460CIS3-10
LTAZ LT1460DIS3-10
LTEV LT1460CS3-2.5
LTEW LT1460IS3-2.5
LTEX LT1460CS3-3
LTEY LT1460IS3-3
5-Lead SOT-23
MARK FULL PART NUMBER
LTCX LTC1517CS5-5
LTED LT1613CS5
LTEE LTC1694CS5
LTEF LT1517CS5-3.3
LTEP LTC1663CS5
LTES LT1611CS5
LTET LT1611IS5
6-Lead SOT-23
MARK FULL PART NUMBER
LTFK LTC1754CS6-5
16-Lead SSOP
MARK FULL PART NUMBER
1067 LTC1067CGN
106750 LTC1067-50CGN
106751 LTC1067-50IGN
1067I LTC1067IGN
1372 LT1372CGN
1372H LT1372HVCGN
1372HI LT1372HVIGN
1372I LT1372IGN
1380 LTC1380CGN
1380I LTC1380IGN
1393 LTC1393CGN
1393I LTC1393IGN
1399 LT1399CGN
1399I LT1399IGN
1430A LTC1430ACGN
1430AI LTC1430AIGN
1433 LTC1433CGN
1433I LTC1433IGN
1473 LTC1473CGN
1473I LTC1473IGN
1473L LTC1473LCGN
1473LI LTC1473LIGN
1510 LT1510CGN
1510I LT1510IGN
15105 LT1510-5CGN
15105I LT1510-5IGN
1512 LT1512CGN
1512I LT1512IGN
1550 LTC1550CGN
1550I LTC1550IGN
1550L LTC1550LCGN
1550LI LTC1550LIGN
1555 LTC1555CGN
1555I LTC1555IGN
155833 LTC1558CGN-3.3
15585 LTC1558CGN-5
155933 LTC1559CGN-3.3
15595 LTC1559CGN-5
1579 LT1579CGN
15793 LT1579CGN-3
157933 LT1579CGN-3.3
15795 LT1579CGN-5
1579I LT1579IGN
1579I3 LT1579IGN-3
1579I5 LT1579IGN-5
1620 LT1620CGN
1620I LT1620IGN
1621 LT1621CGN
1621I LT1621IGN
1643H LTC1643HCGN
1643HI LTC1643HIGN
1643L LTC1643LCGN
1643LI LTC1643LIGN
1660 LTC1660CGN
1660I LTC1660IGN
1675 LT1675CGN
579I33 LT1579IGN-3.3
TAPE AND REEL
13-52
TAPE AND REEL
TAPE A D REEL SPECIFICATIO S—SURFACE OU T
UUU
W
Tape and Reel Packing
Tape and reel packing is available for all SO, SOT-23,
SOT-223, SSOP, TSSOP and DD packages in accordance
with EIA Specifications 481-1-A and 481-2 (all SOT pack-
age styles follow 481-1-A guide lines for package orien-
tation in the carrier tape and SOT-223 package style tape
width is 16mm). Table 1 lists the applicable tape widths,
dimensions and quantities for all LTC small outline prod-
ucts. Consult factory for tape and reel pricing and mini-
mum order requirements.
Table 1. Tape and Reel Specifications
LTC Package LTC Number of W P P
0
Reel Units
Code Designator Package Style Leads Offered Tape Width Component Pitch Hole Pitch Diameter per Reel
F TSSOP (4.4mm) 20 16mm 8mm 4mm 13" 2,500
FW TSSOP (6.1mm) 48, 56 24mm 12mm 4mm 13" 1,800
G SSOP (5.3mm) 16 16mm 12mm 4mm 13" 2,000
G SSOP (5.3mm 20, 24 16mm 12mm 4mm 13" 1,800
G SSOP (5.3mm 28/36 24mm 12mm 4mm 13" 2,000
GN SSOP (0.150) 16 12mm 8mm 4mm 13" 2,500
GN SSOP (0.150) 20, 24 16mm 8mm 4mm 13" 2,500
GW SSOP (7.62mm) 36, 44 24mm 12mm 4mm 13" 1,000
M, Q, R DD 3, 5 or 7 24mm 16mm 4mm 13" 750
MS8 MSOP (0.118) 8 12mm 8mm 4mm 13" 2,500
MS10 MSOP (0.118) 10 12mm 8mm 4mm 13" 2,500
S8 S8 (0.150) 8 12mm 8mm 4mm 13" 2,500
S S (0.150) 14 16mm 8mm 4mm 13" 2,500
S S (0.150) 16 16mm 8mm 4mm 13" 2,500
ST SOT-223 3 16mm 12mm 4mm 13" 2,000
SW SW (0.300) 16 16mm 12mm 4mm 13" 1,000
SW SW (0.300) 18 24mm 12mm 4mm 13" 1,000
SW SW (0.300) 20 24mm 12mm 4mm 13" 1,000
SW SW (0.300) 24 24mm 12mm 4mm 13" 1,000
SW SW (0.300) 28 24mm 12mm 4mm 13" 1,000
S3 SOT-23 3 8mm 4mm 4mm 7" 2,500
S4 SOT-143 4 8mm 4mm 4mm 7" 2,500
S5 SOT-23 5 8mm 4mm 4mm 7" 2,500
S6 SOT-23 6 8mm 4mm 4mm 7" 2,500
TAPE AND REEL
13-53
TAPE A D REEL SPECIFICATIO S—SURFACE OU T
UUU
W
Note 2: Tape and components shall pass around radius “R” without
damage.
Note 3: Dimensions are in millimeters (inches) unless otherwise noted.
Note 1: A
0
B
0
K
0
are determined by component size. The clearance
between the component and the cavity must be within 0.05 (0.002) min.
to 0.65 (0.026) max. for 12mm tape, 0.05 (0.002) min. to 0.90 (0.035)
max. for 16mm tape and 0.050 (0.002) min. to 1.00 (0.039) max. for
24mm tape and larger. The component cannot rotate more than 10° within
the determined cavity.
Embossed Carrier Dimensions (8mm, 12mm, 16mm, 24mm Tape Only)
D
0
T
P
0
T
2
T
1
P
2
P
1
B
1
B
0
K
0
F
E
1
W
A
0
SEE NOTE 1
USER DIRECTION OF FEED CENTER LINES
OF CAVITY
D
1
FOR COMPONENTS
2.0mm × 1.2mm
AND LARGER
10 PITCHES CUMULATIVE
TOLERANCE ON TAPE
±0.2mm(±0.008)
EMBOSSMENT
TOP COVER
TAPE
SEE NOTE 1
FOR MACHINE REFERENCE ONLY
INCLUDING DRAFT AND RADII
CONCENTRIC AROUND B
0
SMP 12
R MIN
SMP 14
BENDING RADIUS
SEE NOTE 2
Bending Radius
Embossed Tape — Constant Dimensions
Tape Size D
O
E
1
P
0
P
2
T Max T
1
Max A
0
B
0
K
0
8mm +0.10 1.75 ± 0.10 4.0 ± 0.10 2.0 ± 0.05 0.600 0.10 See Note 1
12mm 1.5 – 0.0 (0.069 ± 0.004) (0.157 ± 0.004) (0.079 ± 0.002) (0.024) (0.004)
16mm +0.004
24mm (0.059) – 0.0
Embossed Tape Variable Dimensions
Tape Size B
1
Max D
1
Min F T
2
Max R Min W Max
8mm 4.35 1.0 3.5 ±0.005 2.5 25 8.3
(0.171) (0.039) (0.098) 0.984
12mm 8.2 1.5 5.5 ±0.05 6.5 30 12.3
(0.323) (0.059) (0.217 ±0.002) (0.256) (0.256) (1.181)
16mm 12.1 1.5 7.5 ±0.10 8.0 40 16.3
(0.476) (0.217 ±0.002) (0.295 ±0.004) (0.315) (1.575)
24mm 20.1 1.5 11.5 ±0.10 12.0 50 24.3
(0.791) (0.217 ±0.002) (0.453 ±0.004) (0.472) (1.969)
TAPE AND REEL
13-54
Tape Camber (Top View)
1mm
(0.039)
MAX
100mm
(3.937)
1mm
(0.039)
MAX
250mm
(9.843)
SMP 15
TAPE
ALLOWABLE CAMBER TO BE 1mm/100mm NONACCUMULATIVE OVER 250mm
500mm (19.69) MIN
160mm (6.30) MIN COMPONENTS
USER DIRECTION OF FEED
EMPTY COMPONENT POCKETS
SEALED WITH COVER TAPE
EMPTY COMPONENT POCKETS
SEALED WITH COVER TAPE
COVER TAPE
COVER TAPE
CARRIER TAPE
END START
SMP 16
Tape Leader (Start/End) Specification
Component Rotation
TAPE A D REEL SPECIFICATIO S—SURFACE OU T
UUU
W
10° MAXIMUM
COMPONENT ROTATION
TYPICAL
COMPONENT CAVITY
CENTER LINE
SMP 13
TYPICAL
COMPONENT
CENTER LINE
A
O
B
O
TAPE AND REEL
13-55
TAPE A D REEL SPECIFICATIO S—SURFACE OU T
UUU
W
S3
SOT-23 Devices
S5
SOT-23 Devices
S6
SOT-23 Devices
SMP 30
USER DIRECTION OF FEED
S4
SOT-143 Devices
SMP 32
USER DIRECTION OF FEED
SMP 29
USER DIRECTION OF FEED
SMP 17
USER DIRECTION OF FEED
TAPE AND REEL
13-56
SMP 17
USER DIRECTION OF FEED
ST
SOT-223 Devices
M, Q, R
DD Pak Devices
SMP 19
USER DIRECTION OF FEED
F, FW, G, GN, GW, S8, S, SW,
MS8, MS10, SSOP, TSSOP Devices
TAPE A D REEL SPECIFICATIO S—SURFACE OU T
UUU
W
SMP 18
USER DIRECTION OF FEED
TAPE AND REEL
13-57
TAPE A B C D* N W
1
W
2
SIZE MAX MIN MIN MIN MAX MAX
8mm 180 1.5 13.0 ±0.20 20.2 60 + 1.0 14.4
(7.09) (0.059) (0.512 ±0.008) (0.795) (2.36) 8.4 –0.0 (0.567)
+0.059
0.331 –0.00
8mm 330 1.5 13.0 ±0.20 20.2 50 +1.0 14.4
(12.922) (0.059) (0.512 ±0.008) (0.795) (1.97) 8.4 –0.0 (0.567)
+0.059
0.331 –0.00
12mm 180 1.5 13.0 ±0.20 20.2 60 +2.0 18.4
(7.09) (0.059) (0.512 ±0.008) (0.795) (2.36) 12.4 – 0.0 (0.724)
+0.078
0.488 – 0.00
12mm 330 1.5 13.0 ±0.20 20.2 50 +2.0 18.4
(12.992) (0.059) (0.512 ±0.008) (0.795) (1.97) 12.4 – 0.0 (0.724)
+0.078
0.488 – 0.00
16mm 360 1.5 13.0 ±0.20 20.2 50 + 2.0 22.4
(14.173) (0.059) (0.512 ±0.008) (0.795) (1.97) 16.4 –0.00 (0.882)
+0.078
0.646 –0.00
24mm 360 1.5 13.0 ±0.20 20.2 60 + 2.0 30.4
(14.173) (0.059) (0.512 ±0.008) (0.795) (2.36) 24.4 –0.00 (1.197)
+0.078
0.961 –0.00
Metric dimensions will govern.
Note 1: All dimensions in millimeters (inches) unless otherwise noted.
Note 2: English measurements rounded and for reference only.
REEL DI E SIO S—SURFACE OU T
UWU U
W
TOP COVER TAPE
EMBOSSMENT
TAPE
DIRECTION OF FEED
SMP 20
AD*
B*
40mm (1.575) MIN
ACCESS HOLE AT
SLOT LOCATION
TAPE SLOT IN CORE
FOR TAPE START
2.5mm (0.098) MIN WIDTH
10mm (0.394) MIN DEPTH
FULL RADIUS*
*DRIVE SPOKES OPTIONAL. IF USED,
ASTERISKED DIMENSIONS APPLY.
N
C
W1 (MEASURED AT HUB)
W2
(MEASURED AT HUB)
SMP 21
Direction of Feed Reel Dimensions
)
(
)
(
)
(
)
(
)
(
)
(
TAPE AND REEL
13-58
P0
P
P2 F1
P1
F2
SH1
W
H
H4
D
W1
TO-92 01
TO-92 Tape Dimension
356mm
TYP
30.5mm
TYP
TO-92 02
Table 1
SYMBOL DESCRIPTION DIMENSION (mm)
D Sprocket Hole Diameter 4 ± 0.2
H Length from Seating Plane 16 ± 0.5
H1 Sprocket Hole Location 9 ± 0.5
H4 Component Base Height 20 Max
P Sprocket Hole Pitch 12.7 ± 0.2
P0 Pitch of Component 12.7 ± 0.5
P1 Lead Location 3.85 ± 0.5
P2 Center of Seating Plane Location 6.35 ± 0.4
S Component Lead Spacing 5 + 0.8/– 0.2
W Carrier Tape Width 18 +1, –0.5
W1 Adhesive Tape Width 6.0 ± 1.0
F1, F2 Lead-to-Lead Distance 2.5 +0.4, –0.1
TO-92 Reel Dimensions
TAPE A D REEL SPECIFICATIO S—TO-92
UU
TAPE AND REEL
13-59
TAPE A D REEL SPECIFICATIO S—TO-92
UU
Package Orientation on Tape
TO-92 06
ADHESIVE
TAPE
CARRIER
TAPE
TO-92 07
ADHESIVE
TAPE
CARRIER
TAPE
STYLE A: Special Flow TRA
(Rounded Side of Package Faces Toward the Adhesive Tape)
STYLE E: Standard Flow TR
(Flat Side of Package Faces Toward the Adhesive Tape)
Reel Pak Tape Orientation on Reel
ADHESIVE TAPE
FEED DIRECTION
TO-92 03
TAPE AND REEL
13-60
TAPE A D REEL SPECIFICATIO S—TO-92
UU
Ammo Pak Tape Orientation Inside Box
TRAILER
SIDE WITH ADHESIVE TAPE
BOX
STARTER
TO-92 F05
LID
LABELS
ON THIS SIDE
OF BOX
13-61
TO-220 LEAD BEND OPTIONS
Introduction
On the following pages are a variety of lead bend options
available for TO-220 packages from Linear Technology
Corporation. The special adders, flows, and minimums
that have been established for these lead bend options are:
Flows 30 to 37 Special Lead Bends for TO-220
(Minimum Order: 1,000 units)
1,000 to 4,999 units
5,000 to 9,999 units
10,000 to 24,999 units
> 25,000 units
It is important to remember orders for these nonstandard
flows require a minimum 90-day notification for cancella-
tion or rescheduling. Also note that special flow orders for
U.S. distribution must be approved in advance.
TO-220 LEAD BEND OPTIONS
Special lead bends subject
to additional charges and
order conditions. Contact
LTC, Sales/Marketing for
more information.
0.067
(1.70)
BSC 0.028 – 0.038
(0.711 – 0.965)
T5 (FLOW 30) 1098
0.045 – 0.055
(1.143 – 1.397)
0.013 – 0.023
(0.330 – 0.584)
0.110
(2.794)
MIN 0.275
(6.985)
TYP
0.445
(11.303)
TYP
0.025R
(0.635)
TYP
0.600 – 0.620*
(15.240 – 15.748)
0.140 – 0.160*
(3.556 – 4.064)
0.095 – 0.115
(2.413 – 2.921)
0.165 – 0.180
(4.191 – 4.572)
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
SEATING
PLANE
*MEASURED AT SEATING PLANE
TO-220 5-Lead Package Outline (Flow 30)
(LTC DWG # 05-08-1490)
13-62
TO-220 LEAD BEND OPTIONS
TO-220 5-Lead Package Outline (Flow 31)
(LTC DWG # 05-08-1491)
TO-220 3-Lead Package Outline (Flow 32)
(LTC DWG # 05-08-1492)
0.100
(2.54)
BSC
T3 (TO-220)(FLOW 32) 1098
0.165 – 0.180
(4.191 – 4.572) 0.045 – 0.055
(1.143 – 1.397)
0.045 ± 0.020
(1.143 ± 0.508)
0.055 ±0.010
(1.397 ±0.254)
0.013 – 0.023
(0.330 – 0.584)
0.020 ± 0.010
(0.508 ± 0.254)
0.640
(16.256)
MAX
0.150 ± 0.010
(3.810 ± 2.254)
0.050
(1.270)
TYP
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
0.067
(1.70)
BSC 0.028 – 0.038
(0.711 – 0.965)
T5 (TO-220)(FLOW 31) 1098
0.045 – 0.055
(1.143 – 1.397)
0.013 – 0.023
(0.330 – 0.584)
0.135 ± 0.010*
(3.429 ± 0.254)
0.110
(2.794)
MIN 0.275
(6.985)
TYP
0.445
(11.303)
TYP
0.025R
(0.635)
TYP
0.165 – 0.180
(4.191 – 4.572)
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
0.095 – 0.115
(2.413 – 2.921)
0.565 – 0.585*
(14.351 – 14.859)
*MEASURED AT SEATING PLANE
13-63
TO-220 LEAD BEND OPTIONS
TO-220 5-Lead Package Outline (Flow 33)
(LTC DWG # 05-08-1493)
TO-220 3-Lead Package Outline (Flow 34)
(LTC DWG # 05-08-1494)
0.028 – 0.038
(0.711 – 0.965)
0.100
(2.54)
BSC
T3 (TO-220)(FLOW 34) 1197
0.165 – 0.180
(4.191 – 4.572) 0.045 – 0.055
(1.143 – 1.397)
0.120 ± 0.007
(3.048 ± 0.178)
0.100 ± 0.010*
(2.540 ± 0.254)
0.013 – 0.023
(0.330 – 0.584)
0.095 – 0.115
(2.413 – 2.921)
0.570 ± 0.015*
(14.478 ± 0.381)
0.050
(1.270)
TYP
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
SEATING
PLANE
*MEASURED AT SEATING PLANE
0.067
(1.70)
BSC
0.028 – 0.038
(0.711 – 0.965)
T5 (SURFACE) 1197
0.045 – 0.055
(1.143 – 1.397)
0.045 ± 0.020
(1.143 ± 0.508)
0.055 ± 0.010
(1.397 ± 0.254)
0.020 ± 0.010
(0.508 ± 0.254)
0.013 – 0.023
(0.330 – 0.584)
0.640
(16.256)
MAX
0.150 ± 0.010
(3.810 ± 2.254)
0.165 – 0.180
(4.191 – 4.572)
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
13-64
TO-220 LEAD BEND OPTIONS
TO-220 7-Lead Package Outline (Flow 35)
(LTC DWG # 05-08-1495)
TO-220 3-Lead Package Outline (Flow 36)
(LTC DWG # 05-08-1496)
0.050
(1.270)
BSC
0.026 – 0.036
(0.660 – 0.914)
T7 (TO-220)(FLOW 35) 1098
0.150 ± 0.100
(3.810 ± 0.254)
0.045 – 0.055
(1.143 – 1.397)
0.045 ± 0.020
(1.143 ± 0.508)
0.055 ± 0.010
(1.397 ± 0.254)
0.020 ± 0.010
(0.508 ± 0.254)
0.013 – 0.023
(0.330 – 0.584)
0.640
(16.256)
MAX
0.165 – 0.180
(4.191 – 4.572)
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
0.028 – 0.038
(0.711 – 0.965)
0.100
(2.54)
BSC
T3(TO-220)(FLOW 36) 1098
0.165 – 0.180
(4.191 – 4.572) 0.045 – 0.055
(1.143 – 1.397)
0.22
(5.60)
TYP
0.013 – 0.023
(0.330 – 0.584)
0.050
(1.270)
TYP
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
0.700 ± 0.015
(17.8 ± 0.4)
13-65
TO-220 LEAD BEND OPTIONS
TO-220 7-Lead Package Outline (Flow 37)
(LTC DWG # 05-08-1497)
TO-220 5-Lead Package Outline (Flow 40)
(LTC DWG # 05-08-1480)
0.067
(1.70)
BSC
0.028 – 0.038
(0.711 – 0.965)
T5 (FLOW 40) 1098
0.045 – 0.055
(1.143 – 1.397)
0.045 ± 0.020
(1.143 ± 0.508)
0.010 ± 0.010
(0.254 ± 0.254)
0.055 ± 0.010
(1.397 ± 0.254)
0.013 – 0.023
(0.330 – 0.584)
0.640
(16.256)
MAX
0.053
(1.346)
TYP
0.145 ± 0.010
(3.683 ± 0.254)
0.165 – 0.180
(4.191 – 4.572)
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
0.026 – 0.036
(0.660 – 0.914)
0.050
(1.270)
BSC
T7 (TO-220)( FLOW 37) 1098
0.045 – 0.055
(1.143 – 1.397)
0.013 – 0.023
(0.330 – 0.584)
0.140 – 0.160*
(3.556 – 4.064)
0.600 – 0.620*
(15.240 – 15.748)
0.110
(2.794)
MIN 0.275
(6.985)
TYP
0.445
(11.303)
TYP
0.025R
(0.635)
TYP
0.165 – 0.180
(4.191 – 4.572)
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
0.095 – 0.115
(2.413 – 2.921)
*MEASURED AT SEATING PLANE
SEATING PLANE
13-66
TO-220 LEAD BEND OPTIONS
TO-220 3-Lead Package Outline (Flow 41)
(LTC DWG # 05-08-1481)
T3 (FLOW 41) 1098
0.045 – 0.055
(1.143 – 1.397)
0.045 ± 0.020
(1.143 ± 0.508)
0.010 ± 0.010
(0.254 ± 0.254)
0.055 ± 0.010
(1.397 ± 0.254)
0.013 – 0.023
(0.330 – 0.584)
0.640
(16.256)
MAX
0.053
(1.346)
TYP
0.145 ± 0.010
(3.683 ± 0.254)
0.165 – 0.180
(4.191 – 4.572)
0.147 – 0.155
(3.734 – 3.937)
DIA
0.390 – 0.415
(9.906 – 10.541)
0.330 – 0.370
(8.382 – 9.398)
0.460 – 0.500
(11.684 – 12.700)
0.100
(2.54)
BSC
0.570 – 0.620
(14.478 – 15.748)
0.230 – 0.270
(5.842 – 6.858)
0.050
(1.270)
TYP
