OUTPUT
GND
INPUT
-+
2.2k
2.2PF
VDD
-
+
DIAPHRAGM
AIRGAP
BACKPLATE
ELECTRET
CONNECTOR
LMV1012
x
x
x
x
x
x
x
x
xxx
x
xx
xx
IC
LMV1012
www.ti.com
SNAS194H NOVEMBER 2002REVISED MAY 2013
LMV1012 Analog Series: Pre-Amplified IC's for High Gain 2-Wire Microphones
Check for Samples: LMV1012
1FEATURES DESCRIPTION
The LMV1012 is an audio amplifier series for small
2 Typical LMV1012-15, 2.2V Supply, RL= 2.2 k,form factor electret microphones. This 2-wire portfolio
C = 2.2 μF, VIN = 18 mVPP, Unless Otherwise is designed to replace the JFET amplifier currently
Specified being used. The LMV1012 series is ideally suited for
Supply Voltage: 2V - 5V applications requiring high signal integrity in the
presence of ambient or RF noise, such as in cellular
Supply Current: <180 μAcommunications. The LMV1012 audio amplifiers are
Signal to Noise Ratio (A-Weighted): 60 dB specified to operate over a 2.2V to 5.0V supply
Output Voltage Noise (A-Weighted): 89 dBV voltage range with fixed gains of 7.8 dB, 15.6 dB,
Total Harmonic Distortion: 0.09% 20.9 dB, and 23.8 dB. The devices offer excellent
THD, gain accuracy and temperature stability as
Voltage Gain compared to a JFET microphone.
LMV1012-07: 7.8 dB The LMV1012 series enables a two-pin electret
LMV1012-15: 15.6 dB microphone solution, which provides direct pin-to-pin
LMV1012-20: 20.9 dB compatibility with the existing JFET market.
LMV1012-25: 23.8 dB The devices are offered in extremely thin space
Temperature Range: 40°C to 85°C saving 4-bump DSBGA packages. The LMV1012XP
is designed for 1.0 mm canisters and thicker ECM
Offered in 4-Bump DSBGA Packages canisters. These extremely miniature packages are
designed for electret condenser microphones (ECM)
APPLICATIONS form factor.
Cellular Phones
Headsets
Mobile Communications
Automotive Accessories
PDAs
Accessory Microphone Products
Schematic Diagram Built-In Gain Electret Microphone
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2002–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
LMV1012
SNAS194H NOVEMBER 2002REVISED MAY 2013
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
Absolute Maximum Ratings(1)(2)
Human Body Model 2500V
ESD Tolerance(3) Machine Model 250V
Supply Voltage VDD - GND 5.5V
Storage Temperature Range 65°C to 150°C
Junction Temperature(4) 150°C max
Mounting Temperature Infrared or Convection (20 sec.) 235°C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the 5V Electrical Characteristics.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) Human Body Model (HBM) is 1.5 kin series with 100 pF.
(4) The maximum power dissipation is a function of TJ(MAX) ,θJA and TA. The maximum allowable power dissipation at any ambient
temperature is PD= (TJ(MAX) - TA)/θJA. All numbers apply for packages soldered directly into a PC board.
Operating Ratings(1)
Supply Voltage 2V to 5V
Temperature Range 40°C to 85°C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the 5V Electrical Characteristics.
2Submit Documentation Feedback Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LMV1012
LMV1012
www.ti.com
SNAS194H NOVEMBER 2002REVISED MAY 2013
2.2V Electrical Characteristics(1)
Unless otherwise specified, all limits are specified for TJ= 25°C, VDD = 2.2V, VIN = 18 mV, RL= 2.2 kand C = 2.2 μF.
Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions Min(2) Typ(3) Max(2) Units
IDD Supply Current VIN = GND LMV1012-07 139 250
300
LMV1012-15 180 300
325 μA
LMV1012-20 160 250
300
LMV1012-25 141 250
300
SNR Signal to Noise Ratio f = 1 kHz, VIN = 18 mV, LMV1012-07 59
A-Weighted LMV1012-15 60 dB
LMV1012-20 61
LMV1012-25 61
VIN Max Input Signal f = 1 kHz and THD+N < LMV1012-07 170
1% LMV1012-15 100 mVPP
LMV1012-20 50
LMV1012-25 28
VOUT Output Voltage VIN = GND LMV1012-07 1.65 1.90 2.03
1.54 2.09
LMV1012-15 1.54 1.81 1.94
1.48 2.00 V
LMV1012-20 1.65 1.85 2.03
1.55 2.13
LMV1012-25 1.65 1.90 2.02
1.49 2.18
fLOW Lower 3dB Roll Off Frequency RSOURCE = 5065 Hz
fHIGH Upper 3dB Roll Off Frequency RSOURCE = 5095 kHz
enOutput Noise A-Weighted LMV1012-07 96
LMV1012-15 89 dBV
LMV1012-20 84
LMV1012-25 82
THD Total Harmonic Distortion f = 1 kHz, LMV1012-07 0.10
VIN = 18 mV LMV1012-15 0.09 %
LMV1012-20 0.12
LMV1012-25 0.15
CIN Input Capacitance 2 pF
ZIN Input Impedance >1000 G
AVGain f = 1 kHz, LMV1012-07 6.4 7.8 9.5
RSOURCE = 505.5 10.0
LMV1012-15 14.0 15.6 16.9
13.1 17.5 dB
LMV1012-20 19.5 20.9 22.0
17.4 23.3
LMV1012-25 22.5 23.8 25.0
21.4 25.7
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ= TA. No specification of parametric performance is indicated in the electrical tables under
conditions of internal self-heating where TJ> TA.
(2) All limits are specified by design or statistical analysis.
(3) Typical values represent the most likely parametric norm.
Copyright © 2002–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LMV1012
LMV1012
SNAS194H NOVEMBER 2002REVISED MAY 2013
www.ti.com
5V Electrical Characteristics(1)
Unless otherwise specified, all limits are specified for TJ= 25°C, VDD = 5V, VIN = 18 mV, RL= 2.2 kand C = 2.2 μF.
Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions Min(2) Typ(3) Max(2) Units
IDD Supply Current VIN = GND LMV1012-07 158 250
300
LMV1012-15 200 300
325 μA
LMV1012-20 188 260
310
LMV1012-25 160 250
300
SNR Signal to Noise Ratio f = 1 kHz, VIN = 18 mV, LMV1012-07 59
A-Weighted LMV1012-15 60 dB
LMV1012-20 61
LMV1012-25 61
VIN Max Input Signal f = 1 kHz and THD+N < LMV1012-07 170
1% LMV1012-15 100 mVPP
LMV1012-20 55
LMV1012-25 28
VOUT Output Voltage VIN = GND LMV1012-07 4.45 4.65 4.80
4.38 4.85
LMV1012-15 4.34 4.56 4.74
4.28 4.80 V
LMV1012-20 4.40 4.58 4.75
4.30 4.85
LMV1012-25 4.45 4.65 4.83
4.39 4.86
fLOW Lower 3dB Roll Off Frequency RSOURCE = 5067 Hz
fHIGH Upper 3dB Roll Off Frequency RSOURCE = 50150 kHz
enOutput Noise A-Weighted LMV1012-07 96
LMV1012-15 89 dBV
LMV1012-20 84
LMV1012-25 82
THD Total Harmonic Distortion f = 1 kHz, LMV1012-07 0.12
VIN = 18 mV LMV1012-15 0.13 %
LMV1012-20 0.18
LMV1012-25 0.21
CIN Input Capacitance 2 pF
ZIN Input Impedance >1000 G
AVGain f = 1 kHz, LMV1012-07 6.4 8.1 9.5
RSOURCE = 505.5 10.7
LMV1012-15 14.0 15.6 16.9
13.1 17.5 dB
LMV1012-20 19.2 21.1 22.3
17.0 23.5
LMV1012-25 22.5 23.9 25.0
21.2 25.8
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ= TA. No specification of parametric performance is indicated in the electrical tables under
conditions of internal self-heating where TJ> TA.
(2) All limits are specified by design or statistical analysis.
(3) Typical values represent the most likely parametric norm.
4Submit Documentation Feedback Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LMV1012
A1
GND
B2
GND
B1
INPUT
X
A2
OUTPUT
LMV1012
www.ti.com
SNAS194H NOVEMBER 2002REVISED MAY 2013
Connection Diagram
4-Bump DSBGA (Top View)
NOTE
Pin numbers are referenced to package marking text orientation.
The actual physical placement of the package marking will vary slightly from part to part.
The package will designate the date code and will vary considerably. Package marking
does not correlate to device type in any way.
Copyright © 2002–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LMV1012
10 1k 1M
FREQUENCY (Hz)
0
4
18
GAIN (dB)
100k
10k
100
14
12
2
16
10
8
6
-360
-280
0
-80
-120
-320
-40
-160
-200
-240
PHASE (°)
GAIN
PHASE
2 2.5 3 3.5 4 4.5 5 5.5
100
120
140
160
180
200
220
240
260
SUPPLY CURRENT (PA)
SUPPLY VOLTAGE (V)
-40°C
25°C
85°C
22.5 3 3.5 4 4.5 5
SUPPLY VOLTAGE (V)
100
120
140
160
180
200
220
SUPPLY CURRENT (PA)
5.5
85°C
25°C
-40°C
2 2.5 3 3.5 4 4.5 5 5.5
100
110
120
130
140
150
160
170
180
SUPPLY CURRENT (PA)
SUPPLY VOLTAGE (V)
85°C
25°C
-40°C
22.5 33.5 44.5 55.5
SUPPLY VOLTAGE (V)
120
140
160
180
200
220
240
260
SUPPLY CURRENT (PA)
85°C
25°C
-40°C
LMV1012
SNAS194H NOVEMBER 2002REVISED MAY 2013
www.ti.com
Typical Performance Characteristics
Unless otherwise specified, VS= 2.2V, RL= 2.2 k, C = 2.2 μF, single supply, TA= 25°C
Supply Current vs. Supply Voltage (LMV1012-07) Supply Current vs. Supply Voltage (LMV1012-15)
Figure 1. Figure 2.
Supply Current vs. Supply Voltage (LMV1012-20) Supply Current vs. Supply Voltage (LMV1012-25)
Figure 3. Figure 4.
Gain and Phase vs. Frequency (LMV1012-07) Gain and Phase vs. Frequency (LMV1012-15)
Figure 5. Figure 6.
6Submit Documentation Feedback Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LMV1012
10 100 1k 10k 100k
FREQUENCY (Hz)
0.0
0.1
0.2
0.3
0.4
0.5
0.6
THD+N (%)
VIN = 18 mVPP
10 100 1k 10k 100k
FREQUENCY (Hz)
0.0
0.1
0.2
0.3
0.4
0.5
0.6
THD+N (%)
VIN = 18 mVPP
10 100 1k 10k 100k
FREQUENCY (Hz)
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
THD+N (%)
VIN = 18 mVPP
10 100 1k 10k 100k
FREQUENCY (Hz)
0.0
0.1
0.2
0.3
0.4
0.5
0.6
THD+N (%)
VIN = 18 mVPP
10 1k 1M
FREQUENCY (Hz)
0
10
25
GAIN (dB)
100k
10k
100
20
15
5
GAIN
PHASE
-200
0
300
200
100
-100
250
150
50
-50
-150
PHASE (°)
LMV1012
www.ti.com
SNAS194H NOVEMBER 2002REVISED MAY 2013
Typical Performance Characteristics (continued)
Unless otherwise specified, VS= 2.2V, RL= 2.2 k, C = 2.2 μF, single supply, TA= 25°C
Gain and Phase vs. Frequency (LMV1012-20) Gain and Phase vs. Frequency (LMV1012-25)
Figure 7. Figure 8.
Total Harmonic Distortion vs. Frequency (LMV1012-07) Total Harmonic Distortion vs. Frequency (LMV1012-15)
Figure 9. Figure 10.
Total Harmonic Distortion vs. Frequency (LMV1012-20) Total Harmonic Distortion vs. Frequency (LMV1012-25)
Figure 11. Figure 12.
Copyright © 2002–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LMV1012
10 100 1k 10k 100k
FREQUENCY (Hz)
-150
-145
-140
-135
-130
-125
-120
-115
-110
-105
-100
NOISE (dBV/
Hz)
INPUT IS CONNECTED
TO GND
10 100 1k 10k 100k
FREQUENCY (Hz)
-150
-145
-140
-135
-130
-125
-120
-115
-110
-105
-100
INPUT IS CONNECTED TO
GND
NOISE (dBV/
Hz)
0 10 20 30 40 50 60
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
THD+N (%)
INPUT VOLTAGE (mVPP)
f = 1 kHz
0 10 20 30 40
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
THD+N (%)
INPUT VOLTAGE (mVPP)
f = 1 kHz
0 50 100 150 200 250
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
THD+N (%)
INPUT VOLTAGE (mVPP)
f = 1 kHz
0 20 40 60 80 100 120
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
THD+N (%)
INPUT VOLTAGE (mVPP)
f = 1 kHz
LMV1012
SNAS194H NOVEMBER 2002REVISED MAY 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise specified, VS= 2.2V, RL= 2.2 k, C = 2.2 μF, single supply, TA= 25°C
Total Harmonic Distortion vs. Input Voltage (LMV1012-07) Total Harmonic Distortion vs. Input Voltage (LMV1012-15)
Figure 13. Figure 14.
Total Harmonic Distortion vs. Input Voltage (LMV1012-20) Total Harmonic Distortion vs. Input Voltage (LMV1012-25)
Figure 15. Figure 16.
Output Noise vs. Frequency (LMV1012-07) Output Noise vs. Frequency (LMV1012-15)
Figure 17. Figure 18.
8Submit Documentation Feedback Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LMV1012
10 100 1k 10k 100k
FREQUENCY (Hz)
-150
-145
-140
-135
-130
-125
-120
-115
-110
-105
-100
NOISE (dBV/
Hz)
INPUT IS CONNECTED
TO GND
10 100 1k 10k 100k
FREQUENCY (Hz)
-150
-145
-140
-135
-130
-125
-120
-115
-110
-105
-100
NOISE (dBV/
Hz)
INPUT IS CONNECTED
TO GND
LMV1012
www.ti.com
SNAS194H NOVEMBER 2002REVISED MAY 2013
Typical Performance Characteristics (continued)
Unless otherwise specified, VS= 2.2V, RL= 2.2 k, C = 2.2 μF, single supply, TA= 25°C
Output Noise vs. Frequency (LMV1012-20) Output Noise vs. Frequency (LMV1012-25)
Figure 19. Figure 20.
Copyright © 2002–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LMV1012
10 100 1k 10k 100k
FREQUENCY (Hz)
-70
-60
-50
-40
-30
-20
-10
0
10
dBV
DIAPHRAGM
AIRGAP
BACKPLATE
ELECTRET
CONNECTOR
LMV1012
x
x
x
x
x
x
x
x
xxx
x
xx
xx
IC
LMV1012
SNAS194H NOVEMBER 2002REVISED MAY 2013
www.ti.com
APPLICATION SECTION
HIGH GAIN
The LMV1012 series provides outstanding gain versus the JFET and still maintains the same ease of
implementation, with improved gain, linearity and temperature stability. A high gain eliminates the need for extra
external components.
BUILT IN GAIN
The LMV1012 is offered in 0.3 mm height space saving small 4-pin DSBGA packages in order to fit inside the
different size ECM canisters of a microphone. The LMV1012 is placed on the PCB inside the microphone.
The bottom side of the PCB usually shows a bull's eye pattern where the outer ring, which is shorted to the metal
can, should be connected to the ground. The center dot on the PCB is connected to the VDD through a resistor.
This phantom biasing allows both supply voltage and output signal on one connection.
Figure 21. Built in Gain
A-WEIGHTED FILTER
The human ear has a frequency range from 20 Hz to about 20 kHz. Within this range the sensitivity of the human
ear is not equal for each frequency. To approach the hearing response weighting filters are introduced. One of
those filters is the A-weighted filter.
The A-weighted filter is usually used in signal to noise ratio measurements, where sound is compared to device
noise. This filter improves the correlation of the measured data to the signal to noise ratio perceived by the
human ear.
Figure 22. A-Weighted Filter
10 Submit Documentation Feedback Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LMV1012
A-WEIGHTED FILTER
5 pF
LMV1012
www.ti.com
SNAS194H NOVEMBER 2002REVISED MAY 2013
MEASURING NOISE AND SNR
The overall noise of the LMV1012 is measured within the frequency band from 10 Hz to 22 kHz using an A-
weighted filter. The input of the LMV1012 is connected to ground with a 5 pF capacitor, as in Figure 23. Special
precautions in the internal structure of the LMV1012 have been taken to reduce the noise on the output.
Figure 23. Noise Measurement Setup
The signal to noise ratio (SNR) is measured with a 1 kHz input signal of 18 mVPP using an A-weighted filter. This
represents a sound pressure level of 94 dB SPL. No input capacitor is connected for the measurement.
SOUND PRESSURE LEVEL
The volume of sound applied to a microphone is usually stated as a pressure level referred to the threshold of
hearing of the human ear. The sound pressure level (SPL) in decibels is defined by:
Sound pressure level (dB) = 20 log Pm/PO
where
Pmis the measured sound pressure
POis the threshold of hearing (20 μPa). (1)
In order to be able to calculate the resulting output voltage of the microphone for a given SPL, the sound
pressure in dB SPL needs to be converted to the absolute sound pressure in dBPa. This is the sound pressure
level in decibels referred to 1 Pascal (Pa).
The conversion is given by:
dBPa = dB SPL + 20*log 20 μPa (2)
dBPa = dB SPL - 94 dB (3)
Translation from absolute sound pressure level to a voltage is specified by the sensitivity of the microphone. A
conventional microphone has a sensitivity of -44 dBV/Pa.
Copyright © 2002–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LMV1012
10 1k 1M
FREQUENCY (Hz)
-5
5
20
GAIN (dB)
100k
10k
100
15
10
0
VDD = 2.2V
-40°C
25°C
85°C
ABSOLUTE
SOUND
PRESSURE
[dBPa]
-94 dB SENSITIVITY
[dBV/Pa]
SOUND
PRESSURE
[dB SPL]
VOLTAGE
[dBV]
LMV1012
SNAS194H NOVEMBER 2002REVISED MAY 2013
www.ti.com
Figure 24. dB SPL to dBV Conversion
Example: Busy traffic is 70 dB SPL
VOUT = 70 94 44 = 68 dBV (4)
This is equivalent to 1.13 mVPP
Since the LMV1012-15 has a gain of 6 (15.6 dB) over the JFET, the output voltage of the microphone is 6.78
mVPP. By implementing the LMV1012-15, the sensitivity of the microphone is -28.4 dBV/Pa (44 + 15.6).
LOW FREQUENCY CUT OFF FILTER
To reduce noise on the output of the microphone a low frequency cut off filter has been implemented. This filter
reduces the effect of wind and handling noise.
It's also helpful to reduce the proximity effect in directional microphones. This effect occurs when the sound
source is very close to the microphone. The lower frequencies are amplified which gives a bass sound. This
amplification can cause an overload, which results in a distortion of the signal.
Figure 25. LMV1012-15 Gain vs. Frequency Over Temperature
The LMV1012 is optimized to be used in audio band applications. By using the LMV1012, the gain response is
flat within the audio band and has linearity and temperature stability (see Figure 25).
12 Submit Documentation Feedback Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LMV1012
INPUT
OUTPUT
VDD
10 pF 33 pF
LMV1012
www.ti.com
SNAS194H NOVEMBER 2002REVISED MAY 2013
NOISE
Noise pick-up by a microphone in cell phones is a well-known problem. A conventional JFET circuit is sensitive
for noise pick-up because of its high output impedance, which is usually around 2.2 k.
RF noise is amongst other caused by non-linear behavior. The non-linear behavior of the amplifier at high
frequencies, well above the usable bandwidth of the device, causes AM-demodulation of high frequency signals.
The AM modulation contained in such signals folds back into the audio band, thereby disturbing the intended
microphone signal. The GSM signal of a cell phone is such an AM-modulated signal. The modulation frequency
of 216 Hz and its harmonics can be observed in the audio band. This kind of noise is called bumblebee noise.
RF noise caused by a GSM signal can be reduced by connecting two external capacitors to ground, see
Figure 26. One capacitor reduces the noise caused by the 900 MHz carrier and the other reduces the noise
caused by 1800/1900 MHz.
Figure 26. RF Noise Reduction
Copyright © 2002–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LMV1012
LMV1012
SNAS194H NOVEMBER 2002REVISED MAY 2013
www.ti.com
REVISION HISTORY
Changes from Revision G (May 2013) to Revision H Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 13
14 Submit Documentation Feedback Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LMV1012
PACKAGE OPTION ADDENDUM
www.ti.com 16-May-2013
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish MSL Peak Temp
(3)
Op Temp (°C) Top-Side Markings
(4)
Samples
LMV1012TP-07/NOPB ACTIVE DSBGA YPB 4 250 TBD Call TI Call TI
LMV1012TP-15/NOPB ACTIVE DSBGA YPB 4 250 TBD Call TI Call TI
LMV1012TP-25/NOPB ACTIVE DSBGA YPB 4 250 TBD Call TI Call TI
LMV1012TPX-15/NOPB ACTIVE DSBGA YPB 4 3000 TBD Call TI Call TI -40 to 85
LMV1012TPX-25/NOPB ACTIVE DSBGA YPB 4 3000 TBD Call TI Call TI -40 to 85
LMV1012UP-07/NOPB ACTIVE DSBGA YPC 4 250 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM
LMV1012UP-15/NOPB ACTIVE DSBGA YPC 4 250 TBD Call TI Call TI
LMV1012UP-20/NOPB ACTIVE DSBGA YPC 4 250 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM
LMV1012UP-25/NOPB ACTIVE DSBGA YPC 4 250 TBD Call TI Call TI
LMV1012UPX-07/NOPB ACTIVE DSBGA YPC 4 3000 TBD Call TI Call TI -40 to 85
LMV1012UPX-15/NOPB ACTIVE DSBGA YPC 4 3000 TBD Call TI Call TI
LMV1012UPX-20/NOPB ACTIVE DSBGA YPC 4 3000 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM
LMV1012UPX-25/NOPB ACTIVE DSBGA YPC 4 3000 TBD Call TI Call TI -40 to 85
LMV1012XP-15/NOPB ACTIVE DSBGA YPE 4 250 TBD Call TI Call TI
LMV1012XP-25/NOPB ACTIVE DSBGA YPE 4 250 TBD Call TI Call TI
LMV1012XPX-15/NOPB ACTIVE DSBGA YPE 4 3000 TBD Call TI Call TI -40 to 85
LMV1012XPX-25/NOPB ACTIVE DSBGA YPE 4 3000 TBD Call TI Call TI -40 to 85
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
PACKAGE OPTION ADDENDUM
www.ti.com 16-May-2013
Addendum-Page 2
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
MECHANICAL DATA
YPB0004
www.ti.com
TPA04XXX (Rev B)
0.5±0.045 D
E
4215097/A 12/12
A
. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
NOTES:
D: Max =
E: Max =
1.057 mm, Min =
0.981 mm, Min =
0.996 mm
0.92 mm
MECHANICAL DATA
YPC0004
www.ti.com
UPA04XXX (Rev C)
0.350±0.045
D
E
4215139/A 12/12
A
. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
NOTES:
D: Max =
E: Max =
1.057 mm, Min =
0.981 mm, Min =
0.996 mm
0.92 mm
MECHANICAL DATA
YPE0004
www.ti.com
XPA04XXX (Rev C)
TOP SIDE OF PACKAGE BOTTOM SIDE OF PACKAGE
0.250±0.045
D
E
4215203/A 12/12
A
. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
NOTES:
D: Max =
E: Max =
1.057 mm, Min =
0.981 mm, Min =
0.996 mm
0.92 mm
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated