User's Manual IE-78K0-NS In-Circuit Emulator Target Devices 78K/0 Series Document No. U13731EJ3V0UM00 (3rd edition) Date Published May 2003 N CP(K) (c) Printed in Japan [MEMO] 2 User's Manual U13731EJ3V0UM V40 Family is a trademark of NEC Electronics Corporation. Windows is either a registered trademark or a trademark of Microsoft Corporation in the United States and/or other countries. PC/AT is a trademark of International Business Machines Corporation. * The information in this document is current as of February, 2003. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. * No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. * NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. * Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. * While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. * NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above). M8E 02. 11-1 User's Manual U13731EJ3V0UM 3 Regional Information Some information contained in this document may vary from country to country. Before using any NEC Electronics product in your application, pIease contact the NEC Electronics office in your country to obtain a list of authorized representatives and distributors. They will verify: * Device availability * Ordering information * Product release schedule * Availability of related technical literature * Development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, AC supply voltages, and so forth) * Network requirements In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country. [GLOBAL SUPPORT] http://www.necel.com/en/support/support.html NEC Electronics America, Inc. (U.S.) NEC Electronics (Europe) GmbH NEC Electronics Hong Kong Ltd. Santa Clara, California Tel: 408-588-6000 800-366-9782 Duesseldorf, Germany Tel: 0211-65 03 01 Hong Kong Tel: 2886-9318 * Sucursal en Espana Madrid, Spain Tel: 091-504 27 87 * Succursale Francaise Velizy-Villacoublay, France Tel: 01-30-67 58 00 * Filiale Italiana Milano, Italy Tel: 02-66 75 41 * Branch The Netherlands Eindhoven, The Netherlands Tel: 040-244 58 45 * Tyskland Filial Taeby, Sweden Tel: 08-63 80 820 NEC Electronics Hong Kong Ltd. Seoul Branch Seoul, Korea Tel: 02-558-3737 NEC Electronics Shanghai, Ltd. Shanghai, P.R. China Tel: 021-6841-1138 NEC Electronics Taiwan Ltd. Taipei, Taiwan Tel: 02-2719-2377 NEC Electronics Singapore Pte. Ltd. Novena Square, Singapore Tel: 6253-8311 * United Kingdom Branch Milton Keynes, UK Tel: 01908-691-133 J03.4 4 User's Manual U13731EJ3V0UM Major Revisions in This Edition Page Description Throughout Change of interface board for desktop PC from IE-70000-PCI-IF to IE-70000-PCI-IF-A p.12 Modification of Figure 1-1 IE-78K0-NS System Configuration p.36 A.1 Introduction * Deletion of Applicable models p.38 B.1 Introduction * Deletion of Applicable models The mark shows major revised points. User's Manual U13731EJ3V0UM 5 INTRODUCTION Product overview The IE-78K0-NS is used in combination with an emulation board (IE-780xxx-NS-EM1, IE-780xxx-NS-EM4), I/O board (IE-78K0-NS-P0x), and performance board (IE-78K0NS-PA) to debug products in the 78K/0 Series of 8-bit single-chip microcontrollers. Target readers This manual is intended for engineers who perform debugging of systems that employ 78K/0 Series 8-bit single-chip microcontrollers with the IE-78K0-NS and an emulation board (IE-780xxx-NS-EM1, IE-780xxx-NS-EM4), I/O board (IE-78K0-NS-P0x), and performance board (IE-78K0-NS-PA). Purpose The purpose of this manual is to help the user understand the debugging functions that are available by using the IE-78K0-NS and the emulation board (IE-780xxx-NS-EM1, IE-780xxx-NS-EM4), I/O board (IE-78K0-NS-P0x), and performance board (IE-78K0NS-PA) together. Organization When using the IE-78K0-NS, please refer to the manual that comes with the IE-78K0NS (this manual) as well as the manual that comes with the emulation board (IE780xxx-NS-EM1, IE-780xxx-NS-EM4), I/O board (IE-78K0-NS-P0x), and performance board (IE-78K0-NS-PA). IE-780xxx-NS-EM1 IE-78K0-NS IE-780xxx-NS-EM4 User's Manual IE-78K0-NS-P0x (This manual) IE-78K0-NS-PA User's Manual * Basic specifications * Function outline * System configuration * Target interface differences * External interface function How to read this manual To understand the overall functions of the IE-78K0-NS: Read this manual in the order of the contents. To understand the basic specifications: Refer to CHAPTER 1 GENERAL and CHAPTER 2 PART NAMES. For how to connect the IE-780xxx-NS-EM1, IE-780xxx-NS-EM4, IE-78K0-NS-P0x, IE78K0-NS-PA and make settings to debug 78K/0 Series products: Refer to CHAPTER 3 INSTALLATION. 6 User's Manual U13731EJ3V0UM Terminology The meanings of the terms used in this manual are described in the table below. Term Conventions Meaning Emulation device This is a general term that refers to the device in the emulator that is used to emulate the target device. It includes the emulation CPU. Emulation CPU This is the CPU block in the emulator that is used to execute user-generated programs. Target device This is the device to be emulated. Target program This is the program to be debugged. Target system This is the system to be debugged. This includes the target program and the hardware provided by the user. When defined narrowly, it includes only the hardware. Data significance: Higher digits on the left and lower digits on the right Note: Footnote for item marked with Note in the text Caution: Information requiring particular attention Remark: Supplementary information Related Documents Please use the following documents in conjunction with this manual. The related documents listed below may include preliminary versions. However, preliminary versions are not marked as such. { Documents Related to Development Tools (User's Manuals) Document Name Document Number IE-78K0-NS In-Circuit Emulator This manual RA78K0 Assembler Package CC78K0 C Compiler Package Operation U14445E Language U14446E Structured Assembly Language U11789E Operation U14297E Language U14298E TM SM78K Series Ver.2.30 or later System Simulator ID78K Series Integrated Debugger Ver.2.30 or Operation (Windows Based) U15373E External part user open interface specifications U15802E Operation (Windows Based) U15185E later - ID78K0 Integrated Debugger (EWS Based) Reference RX78K0 Real-Time OS Basics U11537E Installation U11536E Project Manager Ver. 3.12 or later (Windows Based) U14610E PG-FP4 Flash Memory Programmer U15260E Caution The documents listed above are subject to change without notice. Be sure to use the latest documents for designing, etc. User's Manual U13731EJ3V0UM 7 CONTENTS CHAPTER 1 GENERAL............................................................................................................................11 1.1 System Configuration....................................................................................................................11 1.2 Hardware Configuration ................................................................................................................13 1.3 Basic Specifications ......................................................................................................................15 1.4 Contents in Carton.........................................................................................................................17 CHAPTER 2 PART NAMES.....................................................................................................................19 2.1 Parts of Main Unit ..........................................................................................................................19 2.2 Board Name....................................................................................................................................21 CHAPTER 3 INSTALLATION ...................................................................................................................23 3.1 Connection .....................................................................................................................................23 3.2 External Trigger Functions ...........................................................................................................32 3.3 Jumper Settings (on Main Board (G-780009 Board)) .................................................................33 3.4 Low-Voltage Emulation Settings..................................................................................................34 APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC .................................36 A.1 Introduction ....................................................................................................................................36 A.2 Installation ......................................................................................................................................37 APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A) ..................................................................38 B.1 Introduction ....................................................................................................................................38 B.2 Installation ......................................................................................................................................39 APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES ...............................40 C.1 Introduction ....................................................................................................................................40 C.2 Installation ......................................................................................................................................41 APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT COMPATIBLES ............43 D.1 Introduction ....................................................................................................................................43 D.2 Installation ......................................................................................................................................44 APPENDIX E REVISION HISTORY .........................................................................................................46 8 User's Manual U13731EJ3V0UM LIST OF FIGURES Figure Number Title Page 1-1 IE-78K0-NS System Configuration .................................................................................................................... 12 1-2 IE-78K0-NS Basic Hardware Configuration 1.................................................................................................... 13 1-3 IE-78K0-NS Basic Hardware Configuration 2.................................................................................................... 13 1-4 IE-78K0-NS Basic Hardware Configuration 3.................................................................................................... 14 1-5 IE-78K0-NS Basic Hardware Configuration 4.................................................................................................... 14 1-6 Contents in Carton............................................................................................................................................. 17 1-7 Contents in Accessory Bag ............................................................................................................................... 18 2-1 Main Board (G-780009 Board) .......................................................................................................................... 22 3-1 Connecting Emulation Board (IE-780xxx-NS-EM1) .......................................................................................... 24 3-2 Connecting Performance Board and Emulation Board (IE-780xxx-NS-EM1) .................................................. 25 3-3 Connecting I/O Board and Emulation Board (IE-780xxx-NS-EM4) ................................................................... 27 3-4 Connecting Performance Board, I/O Board and Emulation Board ................................................................... 28 3-5 Connecting Emulation Probe............................................................................................................................. 30 3-6 Connecting AC Adapter..................................................................................................................................... 31 3-7 Connecting Dedicated Bus Interface Cable....................................................................................................... 31 3-8 Default Settings of JP2, JP3, JP4, JP6, JP7, and JP8 ...................................................................................... 33 3-9 Part Names of G-780009 Board ........................................................................................................................ 34 3-10 Position of TP1 on IE-78K0-NS ......................................................................................................................... 34 3-11 Position of TP1 on IE-78018-NS-EM1 ............................................................................................................... 35 A-1 Mounting of PCI Board and Connector Boards ................................................................................................. 37 C-1 INT JP, WAIT JP Settings ................................................................................................................................. 42 D-1 INT JP, WAIT JP Settings ................................................................................................................................. 45 User's Manual U13731EJ3V0UM 9 LIST OF TABLES Table Number Title Page 1-1 List of Functions (MAX. Specifications) .............................................................................................................15 3-1 Electrical Specifications .....................................................................................................................................32 C-1 SW1 and SW2 Settings When Setting I/O Address to 01DxH...........................................................................41 D-1 SW1 and SW2 Settings When Setting I/O Address to 020xH ...........................................................................44 10 User's Manual U13731EJ3V0UM CHAPTER 1 GENERAL The IE-78K0-NS is a development tool for effectively debugging hardware and software in which a 78K/0 Series 8bit single-chip microcontroller is used. This chapter describes the system configuration and basic specifications of the IE-78K0-NS. 1.1 System Configuration Figure 1-1 shows the system configuration of the IE-78K0-NS. User's Manual U13731EJ3V0UM 11 CHAPTER 1 GENERAL Figure 1-1. IE-78K0-NS System Configuration Integrated debugger ID78K0-NS (sold separately) Device fileNote 4 (available separately) Control software Host machine PC-9800 series, IBM PC/ATTM compatibles Interface board IE-70000-98-IF-C (sold separately) Interface board IE-70000-PC-IF-C (sold separately) Interface board IE-70000-PCI-IF-A (sold separately) PC card interface or Interface cable (NS interface cable) IE-78K0-NS (this product) Interface cable In-circuit emulator NS card MC card cable cableNote 5 PC card interface IE-70000-CD-IF-A (sold separately) + Performance board IE-78K0-NS-PA + AC adapter IE-70000-MC-PC-B (sold separately) + Emulation board IE-78xxx-NS-EM1 (sold separately) Emulation probe NP-xxxxNote 2 (sold separately) Convertion socket EV-xxxxx-xx TQx-xxxxxxNote 3 Notes 12 I/O board IE-78K0-NS-P0x (sold separately) + Emulation board IE-780xxx-NS-EM4 (sold separately) 1. When using the IE-780xxx-NS-EM4, it is necessary to connect an I/O board, IE-78K0-NS-P0x. The IE-780xxx-NS-EM4 and IE-78K0-NS-P0x are sold separately. 2. The NP-xxxxx is a product of Naito Densei Machida Mfg. Co., Ltd. For further information, contact Naito Densei Machida Mfg. Co., Ltd. (TEL: +81-45-475-4191) 3. The TQx-xxxxxx are products of TOKYO ELETECH CORPORATION. For further information, contact Daimaru Kogyo Co., Ltd. Tokyo Electronics Department (TEL: +81-3-3820-7112) Osaka Electronics Department (TEL: +81-6-6244-6672) User's Manual U13731EJ3V0UM CHAPTER 1 GENERAL Notes 1.2 4. The device file can be downloaded from the NEC Electronics website (URL: http://www.necel.com/micro). 5. This is a cable for the V850 Series. This is not used for the IE-78K0-NS. Hardware Configuration The IE-78K0-NS consists of the following hardware units (such as cabinet and boards). * * * * Cabinet 78K0 main board NS interface cable Plastic spacers x 2 Figure 1-2. IE-78K0-NS Basic Hardware Configuration 1 IE-78K0-NS Interface board (sold separately) Dedicated bus interface 78K0 main board Host machine 78K0 Series EM1 board Interface card (sold separately) Emulation probe (sold separately) Figure 1-3. IE-78K0-NS Basic Hardware Configuration 2 IE-78K0-NS Dedicated bus Interface board interface (sold separately) Host machine 78K0 main board 78K0 option board 78K0 Series EM1 board External sense probe Emulation probe (sold separately) Interface card (sold separately) User's Manual U13731EJ3V0UM 13 CHAPTER 1 GENERAL Figure 1-4. IE-78K0-NS Basic Hardware Configuration 3 IE-78K0-NS Interface board (sold separately) Dedicated bus interface Host machine Emulation board 2 (IE-78K0-NS-P0x) 78K0 main board 78K0 Series EM4 board Interface card (sold separately) Emulation probe (sold separately) Figure 1-5. IE-78K0-NS Basic Hardware Configuration 4 Interface board (sold separately) Dedicated bus interface 78K0 main board Host machine 78K0 option board Emulation board 2 (IE-78K0 -NS-P0x) 78K0 Series EM4 board Interface card (sold separately) External sense probe 14 User's Manual U13731EJ3V0UM Emulation probe (sold separately) CHAPTER 1 GENERAL 1.3 Basic Specifications Table 1-1. List of Functions (MAX. Specifications) (1/2) Parameter Description TM Supervisor V40 (operating frequency: 16.0 MHZ) Target device 78K/0 Series (PD780xxx) System clock According to specification of emulation board (sold separately) Clock supply External Pulse input Internal Mounted on emulation board (sold separately) Substitute memory capacity 64 KB Mapping unit Internal ROM 4 KB Internal highspeed RAM 64 bytes Internal low-speed RAM 128 bytes External expansion memory 8 KB Emulation function * Real-time execution * Break execution * Step execution Real-time internal RAM monitor 2 KB of memory space Event detection * Program execution detection * Bus event detection * External trigger detection Event integration * Path condition * Trace qualify condition * Delay condition * Trigger condition Break factor * Event break * Manual break * Command break * Fail-safe break Trigger output (open drain output (1)) Real-time trace Trace factor * All traces * Qualify trace Trace capacity 32 bits x 8 KB Trace content Address, data, and status User's Manual U13731EJ3V0UM 15 CHAPTER 1 GENERAL Table 1-1. List of Functions (MAX. Specifications) (2/2) Parameter Description Execution time measurement Up to 4 mins 28 sec, resolution: 62.5 ns Target interface Emulation probe (sold separately) provided for each target device shape Host interface Dedicated bus interface Low-voltage support Based on the emulation board (sold separately) Host machine PC-9800 series, or IBM PC/AT compatibles Power supply DC 5 V Operation temperature range 10C to 40C Dimensions W240 x D197 x H73 (mm) 16 User's Manual U13731EJ3V0UM CHAPTER 1 GENERAL 1.4 Contents in Carton The IE-78K0-NS carton contains the main unit, cables, an accessory bag, and a guarantee card. Make sure that the accessory bag contains a packing list, this user's manual, spacers, and screws. In case of missing or damaged items, please contact an NEC Electronics sales representative or NEC Electronics distributor. Figure 1-6. Contents in Carton <2> NS interface cable <3> FG cable <4> Accessory bag <1> IE-78K0-NS <5> Guarantee card <1> <2> <3> <4> <5> IE-78K0-NS main unit x 1 NS interface cable x 1 FG cable x 1 Accessory bag x 1 Guarantee card x 1 User's Manual U13731EJ3V0UM 17 CHAPTER 1 GENERAL Check that the accessory bag contains the following items (refer to Figure 1-7 Contents in Accessory Bag). <a> <b> <c> <d> Packing list x 1 User's manual (this manual) x 1 Spacers x 2 Screws x 4 Figure 1-7. Contents in Accessory Bag <a> Packing list <b> User's manual <c> Spacers <d> Screws 18 User's Manual U13731EJ3V0UM CHAPTER 2 PART NAMES This chapter introduces the parts of the IE-78K0-NS main unit. The packing box contains the IE-78K0-NS main unit. If there are any missing or damaged items, please contact an NEC sales representative. Please make sure to fill out and return the guarantee card that comes with the main unit. 2.1 Parts of Main Unit (1) Probe end Target system power supply LED T V C C Small: 13 x 158 mm Large: 16 x 158 mm Probe interface (2) Top view R O T LA U M E IT U C IR C IN POWER Power supply LED User's Manual U13731EJ3V0UM 19 CHAPTER 2 PART NAMES (3) Interface DC IN FG - + Power switch (OFF/ON) 20 Dedicated bus interface connector (HOST-I/F) OFF ON RESET HOST-I/F Reset switch (RESET) User's Manual U13731EJ3V0UM CHAPTER 2 PART NAMES 2.2 Board Name The IE-78K0-NS contains the following board. * Main board (G-780009 Board) x 1 Check that you have the correct board. To access the inside of the unit, remove the four screws from the sides of the main unit and open the lid. User's Manual U13731EJ3V0UM 21 CHAPTER 2 PART NAMES Figure 2-1. Main Board (G-780009 Board) Remark 22 The main board is shown mounted in the main unit User's Manual U13731EJ3V0UM CHAPTER 3 INSTALLATION This chapter describes how to connect the cables to the IE-78K0-NS and the mode settings. 3.1 Connection Connect the following ten products, which are sold separately. Refer to Figure 1-1 System Configuration of IE-78K0-NS in CHAPTER 1 GENERAL for the system configuration of the IE-78K0-NS. * IE-70000-98-IF-C: Interface board (use cable that comes with IE-78K0-NS) * IE-70000-PC-IF-C: Interface board (use cable that comes with IE-78K0-NS) * IE-70000-PCI-IF-A: Interface board (use cable that comes with IE-78K0-NS) * IE-70000-CD-IF-A: PC card interface (use NS card cable) * IE-70000-MC-PS-B: AC adapter * IE-780xxx-NS-EM1: Emulation board * IE-780xxx-NS-EM4: Emulation board * IE-78K0-NS-P0x: I/O board * IE-78K0-NS-PA: Performance board * NP-xxxxx: Emulation probe Caution Connecting and removing cables or components from the target system and changing the settings of switches, etc. should be carried out after turning off the power of the IE-78K0-NS main unit and the target system. User's Manual U13731EJ3V0UM 23 CHAPTER 3 INSTALLATION (1) Connecting emulation board (IE-780xxx xxx-NS-EM1) xxx The IE-780xxx-NS-EM1 is sold separately. Figure 3-1. Connecting Emulation Board (IE-780xxx xxx-NS-EM1) xxx <1> Remove the screws from the sides of the ;; <2> Remove the first plate from the bottom by removing the screws. main unit, and then remove the top cover. <3> Replace the spacers (metal) of the main ;; ;;; <4> Connect the IE-780xxx-EM1 and fasten the board, as indicated in the diagram below, two screws to the emulation board. with the spacers (plastic) attached to the IE78K0-NS. Caution This procedure is needed only when using the IE-78018-NSEM1. ;;; ; ;;; ; Here <5> When using a probe, connect the probe. <6> Replace the top cover and fasten the four screws on the sides. Refer to (5) for the probe connection method. 24 User's Manual U13731EJ3V0UM Emulation board CHAPTER 3 INSTALLATION (2) Connecting performance board (IE-78K0-NS-PA) and emulation board (IE-780xxx xxx-NS-EM1) xxx The IE-78K0-NS-PA and IE-780xxx-NS-EM1 are sold separately. Figure 3-2. Connecting Performance Board and Emulation Board (IE-780xxx xxx-NS-EM1) (1/2) xxx <1> Remove the screws from the sides of the <2> Remove the first and second plates from the bottom by removing the screws. main unit, and then remove the top cover. <3> Connect the IE-78K0-NS-PA and affix the <4> When only connecting the IE-78018-NS-EM1 attached spacers to the IE-78K0-NS-PA at on the IE-78K0-NS-PA, remove spacer 1 five points on the board. (metal) of the following figure and replace spacers 2 and 3 (metal) with the attached spacers (plastic). Attached spacer Attached spacer Fix Fix Spacer 1 Here Spacers 2 and 3 IE-78K0-NS-PA <5> Connect the IE-78xxx-NS-EM1 on the IE- <6> When using a probe, connect the probe. 78K0-NS-PA and fasten the two screws. IE-780xxx-NS-EM1 Refer to (5) for the probe connection method. IE-78K0-NS-PA Refer to the IE-78K0-NS-PA User's Manual for the EXT cable connection method. User's Manual U13731EJ3V0UM 25 CHAPTER 3 INSTALLATION Figure 3-2. Connecting Performance Board and Emulation Board (IE-780xxx xxx-NS-EM1) (2/2) xxx <7> Replace the top cover and fasten the four screws on the sides. IE-780xxx-NS-EM1 IE-78K0-NS-PA 26 User's Manual U13731EJ3V0UM CHAPTER 3 INSTALLATION (3) Connecting I/O board (IE-78K0-NS-P0x x) and emulation board (IE-78K0-NS-P0x x and IE-780xxx xxx-NS-EM4) xxx The IE-78K0-NS-P0x and IE-780xxx-NS-EM4 are sold separately. Figure 3-3. Connecting I/O Board and Emulation Board (IE-780xxx xxx-NS-EM4) xxx <1> Remove the screws from the sides of the main unit, and then remove the top cover. ;;; <2> Remove the second plate from the bottom by removing the screws. ; ;;;;; ;; ; ; ;;; ; <3> Connect the IE-78K0-NS-P0x to the main board. Fix the attached spacers to the IE78K0-NS-P0x at the four corners of the board. <4> Connect the IE-780xxx-NS-EM4 on the IE-78K0- NS-P0x, and fasten the screws at the four corners. IE-780xxx-NS-EM4 Attached spacer Attached spacer Fix Fix ;; ;; ;; ;; IE-78K0-NS-P0x IE-78K0-NS-P0x <5> When using a probe, connect the probe. <6> Replace the top cover and fasten the four screws on the sides. IE-780xxx-NS-EM4 Refer to (5) for the probe connection method. User's Manual U13731EJ3V0UM IE-78K0-NS-P0x 27 CHAPTER 3 INSTALLATION (4) Connecting performance board (IE-78K0-NS-PA), I/O board (IE-78K0-NS-P0x x) and emulation board (IE780xxx xxx-NS-EM1 and IE-78Kxxx xxx-NS-EM4) xxx xxx The IE-78K0-NS-PA, IE-78K0-NS-P0x, and IE-780xxx-NS-EM4 are sold separately. Figure 3-4. Connecting Performance Board, I/O Board and Emulation Board (1/2) <1> Remove the screws from the sides of the <2> Remove the first and third plates from the main unit, and then remove the top cover. bottom by removing the screws. <3> Connect the IE-78K0-NS-PA and affix the <4> Connect the IE-78K0-NS-P0x on the IE- attached spacers to the IE-78K0-NS-PA at 78K0-NS-PA, and fix the spacers to the IE78K0-NS-P0x at the four corners. five points on the board. Attached spacer Fix Attached spacer Fix Attached spacer Fix Attached spacer Fix IE-78K0-NS-P0x Here IE-78K0-NS-PA IE-78K0-NS-PA <5> Connect the IE-780xxx-NS-EM4 on the IE- <6> When using a probe, connect the probe. 78K0-NS-P0x, and fasten the screws at the four corners. IE-78xxx-NS-EM4 IE-78K0-NS-P0x IE-78K0-NS-PA Refer to (5) for the probe connection method. Refer to the IE-78K0-NS-PA User's Manual for the EXT cable connection method. 28 User's Manual U13731EJ3V0UM CHAPTER 3 INSTALLATION Figure 3-4. Connecting Performance Board, I/O Board and Emulation Board (2/2) <7> Replace the top cover and fasten the four screws on the sides. IE-78xxx-NS-EM4 IE-78K0xxx-NS-P0x IE-78K0-NS-PA User's Manual U13731EJ3V0UM 29 CHAPTER 3 INSTALLATION (5) Connecting emulation probe (NP-xxxxx xxxxx) xxxxx The NP-xxxxx is sold separately. Figure 3-5. Connecting Emulation Probe IE-78K0-NS-P0x (this is necessary only when mounting the IE-780xxx-NS-EM4) Emulation probe (NP-xxxxx) IE-780xxx-NS-EMn (n = 1, 4) Main board (G-780009 board) Emulation probe (NP-xxxxx) IE-78K0-NS-PA IE-78K0-NS-P0x (this is necessary only when mounting the IE-780xxx-NS-EM4) IE-780xxx-NS-EMn (n = 1, 4) Main board (G-780009 board) Caution The emulation probe (NP-xxxxx xxxxx) xxxxx mounting location varies depending on the model of the IE780xxx xxx-NS-EMn (n = 1 or 4) in use. For details, refer to the IE-780xxx xxx-NS-EMn User's Manual. xxx xxx 30 User's Manual U13731EJ3V0UM CHAPTER 3 INSTALLATION (6) Connecting AC adapter (IE-70000-MC-PS-B) The IE-70000-MC-PS-B is sold separately. <1> Insert the AC adapter plug into the DC IN socket of the IE-78K0-NS. Figure 3-6. Connecting AC Adapter Dedicated bus interface connector (HOST-I/F) DC IN FG - + OFF ON RESET HOST-I/F Power switch (OFF/ON) Reset switch (RESET) (7) Connecting interface cable <1> Insert the cable into the bus interface connector on the IE-78K0-NS main unit. Figure 3-7. Connecting Dedicated Bus Interface Cable Dedicated bus interface connector (HOST-I/F) DC IN FG - + OFF ON RESET HOST-I/F Power switch (OFF/ON) Reset switch (RESET) Caution The type of interface cable varies depending on whether an interface board or a PC card interface is used. * When using an interface board (IE-70000-98-IF-C, IE-70000-PC-IF-C, or IE-70000-PCI-IF-A) Connect the NS interface cable that comes with the IE-78K0-NS. * When using a PC card interface (IE-70000-CD-IF-A) Connect the NS card cable that comes with the IE-70000-CD-IF-A. The IE-70000-98-IF-C, IE-70000-PC-IF-C, IE-70000-PCI-IF-A, and IE-70000-CD-IF-A are sold separately. User's Manual U13731EJ3V0UM 31 CHAPTER 3 INSTALLATION 3.2 External Trigger Functions (1) EXTOUT At the occurrence of a break event, the EXTOUT pin on the emulation board outputs a low level for 1.3 s. Caution Because the output is open drain, connect a pull-up resistor in the target system. (2) EXTIN The EXTIN pin on the emulation board can be used to input an event signal. Enter high-level pulse signals for two or more CPU clocks. Caution For the electrical specifications, refer to Table 3-1. Table 3-1. Electrical Specifications Parameter High-level input voltage Low-level input voltage 32 MIN. [V] Target voltage x 0.7 0 User's Manual U13731EJ3V0UM MAX. [V] Target voltage Target voltage x 0.3 CHAPTER 3 INSTALLATION 3.3 Jumper Settings (on Main Board (G-780009 Board)) (1) Default jumper settings Figure 3-8. Default Settings of JP2, JP3, JP4, JP6, JP7, and JP8 1 2 3 1 3 5 1 3 5 2 4 JP6 6 2 4 JP7 6 1 3 5 2 4 JP8 6 JP2 1 2 3 JP3 1 2 3 JP4 JP8: Selection of the subsystem clock source (default setting: 1 and 2 shorted) 1 and 2 shorted: Internal (mounted on the emulation board or mounted on the part board by the user) 3 and 4 shorted: External (input via an emulation probe from the target system) Caution Jumper settings differ depending on the emulation board. For details, refer to the relevant emulation board user's manual. User's Manual U13731EJ3V0UM 33 CHAPTER 3 INSTALLATION Figure 3-9. Part Names of G-780009 Board JP7 JP8 CN5 CN7 JP6 P1 P2 JP4 JP3 CN4 CN6 TP1 JP2 3.4 Low-Voltage Emulation Settings Low-voltage emulation can be executed in the IE-78K0-NS by connecting an emulation board that supports lowvoltage operation. (1) When using other than the IE-78018-NS-EM1 when the target is at low voltage, supply the same supply voltage as that of the target to the IE-78K0-NS TP1 terminal pin. (This also applies when the voltage is 5 V.) Figure 3-10. Position of TP1 on IE-78K0-NS CN5 CN7 P1 P2 CN4 CN6 TP1 Remark The maximum current consumption of TP1 is from 100 mA (1.8 V) to 300 mA (5 V). 34 User's Manual U13731EJ3V0UM CHAPTER 3 INSTALLATION (2) When using the IE-78018-NS-EM1 when the target is at low voltage, supply the same supply voltage as that of the target to the TP1 terminal pin on the IE-78018-NS-EM1. (This also applies when the voltage is 5 V.) Figure 3-11. Position of TP1 on IE-78018-NS-EM1 TP1 CN1 Remark CN2 The maximum current consumption of TP1 is from 100 mA (1.8 V) to 300 mA (5 V). Caution For details of the target voltage or maximum current consumption, refer to the relevant emulation board user's manual. User's Manual U13731EJ3V0UM 35 APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC This chapter describes the setting method when connecting the IE-78K0-NS. For details, refer to the IE-70000-PCI-IF-A User's Manual (to be prepared). A.1 Introduction The IE-70000-PCI-IF-A is an interface board for an IE product that is installed in the PCI bus slot of a PC. First of all, check that you have the following items. * Interface board (IE-70000-PCI-IF-A) for desktop PC x 1 * 8-bit connector board (connected to IE-70000-PCI-IF-A) x 1 * 32-bit connector board x 1 * User's manual x 1 * DLL-DISK x 1 * DRV-DISK x 1 <Basic specifications> Hardware resources used * I/O address .........0000H to FFFFH * Interrupts ............Unused * Memory...............Uses 80 bytes Current consumption 300 mA (MAX. when using +5 V) Cautions 1. Do not place heavy objects on or apply pressure to the board. 2. Do not drop the board or subject it to excessive vibration or shock. 3. When removing a cable, do not pull it by the cord. 4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is directly exposed to sunlight. 5. Avoid subjecting the board to extreme changes in temperature or humidity. 6. Do not spill drinks or other liquids onto the board or its accessories. 7. Do not connect a cable for a different product to the connector. 36 User's Manual U13731EJ3V0UM APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC A.2 Installation (1) Board settings There are no jumpers or DIP switches on the IE-70000-PCI-IF-A. (2) 8-bit connector board mounting An 8-bit connector board is premounted at shipment. Remark When a 32-bit board is mounted, place it on the 8-bit connector board using the combination connector (refer to Figure A-1) and fasten them together. Caution The 32-bit connector board is attached for future function expansion. Figure A-1. Mounting of PCI Board and Connector Boards Combination connector 32-bit connector board Combination connector Combination connector CH1 PCI board CH0 8-bit connector board (3) Installation in PC Make sure that the PC is turned off, then install the interface board in the PCI bus slot following the instructions in the PC's manual. (4) PCI driver installation Refer to the supplied DRV_DISK Readme_e.txt for PCI driver installation. (5) Connecting with IE-78K0-NS Using the supplied cable, connect the IE-78K0-NS to the CH0 side. Caution Connection with the IE-78K0-NS is possible on the CH0 side only. User's Manual U13731EJ3V0UM 37 APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A) This chapter describes the setting method when connecting the IE-78K0-NS. For details, refer to the IE-70000-CD-IF-A User's Manual (to be prepared). B.1 Introduction The PC card interface (IE-70000-CD-IF-A) is an interface card for an IE product that is installed in a PC PCI bus slot compliant with PCMCIA2.1/JEIDA standard Ver. 4.2. Check that you have the following items. * PC card interface (IE-70000-CD-IF-A) x 1 * MC-A CABLE x 1 * NS-A CABLE x 1 * User's manual x 1 * DLL-DISK x 1 * DRV-DISK x 1 <Basic specifications> Hardware resources used * I/O address .........20 bytes starting from 220H, 260H, 2E0H, 320H, or 3E0H as a base address * Interrupts ............Unused * Memory...............Unused Current consumption 300 mA (MAX. when using +5 V) Cautions 1. Do not place heavy objects on or apply pressure to the board. 2. Do not drop the board or subject it to excessive vibration or shock. 3. When removing a cable, do not pull it by the cord. 4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is directly exposed to sunlight. 5. Avoid subjecting the board to extreme changes in temperature or humidity. 6. Do not spill drinks or other liquids onto the board or its accessories. 7. Do not connect a cable for a different product to the connector. 38 User's Manual U13731EJ3V0UM APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A) B.2 Installation (1) Installation in PC Insert the PCMCIA card in the card slot when the power supply of the PC is turned on. For Windows NT4.0, insert the card in the slot when the power supply is turned off. Be careful to insert the card in the correct direction. (2) PCMCIA driver installation Refer to the supplied DRV-DISK Readme_e.txt for PCMCIA driver installation. Caution This interface card cannot be connected to the IE-78xxxx xxxx-R. xxxx Actually, installation ends completely by selecting "IE-78xxxx xxxx-R" displayed in the DRV-DISK install menu. In this case, xxxx however, the installation is invalid. (3) Connection with the IE-78K0-NS Using the NS-A CABLE, connect the IE-70000-CD-IF-A to the IE-78K0-NS. Caution Be sure to use the NS-A CABLE when connecting to the IE-78K0-NS. If MC-A is used, the IE70000-CD-IF-A may be damaged. User's Manual U13731EJ3V0UM 39 APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES This chapter describes the setting method when connecting the IE-78K0-NS. For details, refer to the IE-70000-98-IF-C User's Manual (to be prepared). C.1 Introduction The IE-70000-98-IF-C is an interface board for an IE product that is installed in the C bus slot of a PC9800 series machine. Caution The PC98-NX series is treated as an IBM PC/AT compatible machine. Refer to APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF(-A)) FOR DESKTOP PC. First of all, check that you have the correct interface board. * Interface board (IE-70000-98-IF-C) for PC-9800 series x 1 <Basic specifications> Applicable models This product is designed for devices incorporating a PC-9800 series C bus. Hardware resources used * I/O addresses .............. 16 bytes at a 256-byte boundary (00DxH, 01DxH,...FFDxH) * Interrupts and others ... Unused Current consumption 500 mA (MAX. when using +5 V) Cautions 1. Do not place heavy objects on or apply pressure to the board. 2. Do not drop the board or subject it to excessive vibration or shock. 3. When removing a cable, do not pull it by the cord. 4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is directly exposed to sunlight. 5. Avoid subjecting the board to extreme changes in temperature or humidity. 6. Do not spill drinks or other liquids onto the board or its accessories. 7. Do not connect a cable for a different product to the connector. 40 User's Manual U13731EJ3V0UM APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES C.2 Installation (1) I/O address settings SW1 and SW2 are the switches selecting the C bus I/O addresses. SW1 numbers 1 to 8 correspond to C bus addresses A4 to A11, and SW2 numbers 1 to 4 correspond to C bus addresses A12 to A15. In the IE-78K0-NS, the addresses should be set in the 16 bytes between 00DxH and FFDxH. The switch takes the value "0" when ON and "1" when OFF. The addresses used for setup must be values that are not used in the PC system or for other boards. In addition, since these values are used during software installation, make a note of them for future reference. Setting examples of I/O address, SW1 and SW2 are shown below. Table C-1. SW1 and SW2 Settings When Setting I/O Address to 01Dx xH SW1 Number Address 1 2 3 4 5 6 7 8 A4 A5 A6 A7 A8 A9 A10 A11 0 0 0 0 ON OFF 1 SW2 Number 1 Address ON OFF Caution 1 1 1 2 3 4 5 6 7 8 A12 A13 A14 A15 OFF OFF ON OFF 0 0 0 0 0 1 1 1 Use the default setting for SW1 numbers 1 to 4. User's Manual U13731EJ3V0UM 41 APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES (2) Jumper settings The INT JP and WAIT JP are C bus interrupt and WAIT selection jumpers. In the IE-78K0-NS, set INT JP to NO USE, and WAIT JP to 1 and 2 shorted. Figure C-1. INT JP, WAIT JP Settings 1 2 1 NO USE 2 3 Shorted IR3 WAIT JP IR5 IR6 : Shorted IR9 IR11 IR12 IR13 INT JP (3) Installation in PC Make sure that the PC is turned off, then install the interface board in the C bus slot following the instructions in the PC's manual. (4) Connecting with IE-78K0-NS Using the supplied cable, connect the IE-78K0-NS to the CH0 side. Caution Connection with the IE-78K0-NS is possible on the CH0 side only. For connection with other models, refer to their respective manuals. 42 User's Manual U13731EJ3V0UM APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT COMPATIBLES This chapter describes the setting method when connecting the IE-78K0-NS. For details, refer to the IE-70000-PC-IF-C User's Manual (to be prepared). D.1 Introduction The IE-70000-PC-IF-C is an interface board for IBM PC/AT compatibles that is installed in the ISA bus slot of an IBM PC/AT compatible. First of all, check that you have the correct interface board. * Interface board (IE-70000-PC-IF-C) for IBM PC/AT x 1 <Basic specifications> Applicable models The IE-70000-PC-IF-C is designed for IBM PC/AT compatibles incorporating an ISA bus. Hardware resources * I/O address.................. 16 bytes at any 16-byte boundary (020xH to 03FxH) * Interrupts and others ... Unused Current consumption 500 mA (MAX. when using +5 V) Cautions 1. Do not place heavy objects on or apply pressure to the board. 2. Do not drop the board or subject it to excessive vibration or shock. 3. When removing a cable, do not pull it by the cord. 4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is directly exposed to sunlight. 5. Avoid subjecting the board to extreme changes in temperature or humidity. 6. Do not spill drinks or other liquids onto the board or its accessories. 7. Do not connect a cable for a different product to the connector. User's Manual U13731EJ3V0UM 43 APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT COMPATIBLES D.2 Installation (1) I/O address settings SW1 and SW2 are the switches selecting the ISA bus I/O addresses. SW1 numbers 1 to 8 correspond to ISA bus addresses A4 to A11, and SW2 numbers 1 to 4 correspond to ISA bus addresses A12 to A15. In the IE-78K0-NS, the addresses should be set between 020xH and 03FxH. The switch takes the value "0" when ON and "1" when OFF. The addresses used for setup must be values that are not used in the PC system or for other boards. In addition, since these values are used during software installation, make a note of them for future reference. Setting examples of I/O address, SW1 and SW2 are shown below. Table D-1. SW1 and SW2 Settings When Setting I/O Address to 020x xH SW1 Number Address ON 1 2 3 4 5 6 7 8 A4 A5 A6 A7 A8 A9 A10 A11 0 0 0 0 0 0 0 OFF 1 SW2 Number Address ON OFF Caution 44 1 2 3 4 5 6 7 8 A12 A13 A14 A15 OFF OFF ON OFF 0 0 0 0 0 1 1 1 Set SW2 number 7 to ON and SW2 numbers 5, 6, and 8 to OFF. User's Manual U13731EJ3V0UM APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT COMPATIBLES (2) Jumper Settings The INT JP and WAIT JP are C bus interrupt and WAIT selection jumpers. In the IE-78K0-NS, set INT JP to NO USE, and WAIT JP to 1 and 2 shorted. Figure D-1. INT JP, WAIT JP Settings 1 2 1 NO USE 2 3 Shorted IRQ2 WAIT JP IRQ3 IRQ4 : Shorted IRQ5 IRQ6 IRQ7 INT JP (3) Installation in PC Make sure that the PC is turned off, then install the interface board in the ISA bus slot following the instructions in the PC's manual. (4) Connecting with IE-78K0-NS Using the supplied cable, connect the IE-78K0-NS to the CH0 side. Caution Connection with the IE-78K0-NS is possible on the CH0 side only. For connection with other models, refer to their respective manuals. User's Manual U13731EJ3V0UM 45 APPENDIX E REVISION HISTORY A history of the revisions up to this edition is shown below. "Applied to:" indicates the chapters to which the revision was applied. Edition 2nd Major Revisions from Previous Edition Modification of Figure 1-1 IE-78K0-NS System Configuration Modification of Figure 1-2 IE-78K0-NS Basic Hardware Configuration 1 Applied to: CHAPTER 1 GENERAL Addition of 1.4 Contents in Carton 3rd 46 Modification of 3.1 Connection CHAPTER 3 INSTALLATION Addition of INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC APPENDIX A Addition of PC CARD INTERFACE (IE-70000-CD-IF-A) APPENDIX B Addition of REVISION HISTORY APPENDIX E Change of interface board for desk top PC from IE-70000-PCI-IF to IE-70000-PCI-IF-A Throughout Modification of Figure 1-1 IE-78K0-NS System Configuration CHAPTER 1 GENERAL A.1 Introduction * Deletion of Applicable models APPENDIX A B.1 Introduction * Deletion of Applicable models APPENDIX B User's Manual U13731EJ3V0UM [MEMO] User's Manual U13731EJ3V0UM 47