Document No. U13731EJ3V0UM00 (3rd edition)
Date Published May 2003 N CP(K)
Printed in Japan
User’s Manual
IE-78K0-NS
In-Circuit Emulator
Target Devices
78K/0 Series
©
User’s Manual U13731EJ3V0UM
2
[MEMO]
User’s Manual U13731EJ3V0UM 3
V40 Family is a trademark of NEC Electronics Corporation.
Windows is either a registered trademark or a trademark of Microsoft Corporation in the United States and/or
other countries.
PC/AT is a trademark of International Business Machines Corporation.
The information in this document is current as of February, 2003. The information is subject to
change without notice. For actual design-in, refer to the latest publications of NEC Electronics data
sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not
all products and/or types are available in every country. Please check with an NEC Electronics sales
representative for availability and additional information.
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may
appear in this document.
NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from the use of NEC Electronics products listed in this document
or any other liability arising from the use of such products. No license, express, implied or otherwise, is
granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others.
Descriptions of circuits, software and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these
circuits, software and information in the design of a customer's equipment shall be done under the full
responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by
customers or third parties arising from the use of these circuits, software and information.
While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products,
customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To
minimize risks of damage to property or injury (including death) to persons arising from defects in NEC
Electronics products, customers must incorporate sufficient safety measures in their design, such as
redundancy, fire-containment and anti-failure features.
NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and
"Specific".
The "Specific" quality grade applies only to NEC Electronics products developed based on a customer-
designated "quality assurance program" for a specific application. The recommended applications of an NEC
Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of
each NEC Electronics product before using it in a particular application.
The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC
Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications
not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to
determine NEC Electronics' willingness to support a given application.
(Note)
•
•
•
•
•
•
M8E 02. 11-1
(1)
(2)
"NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its
majority-owned subsidiaries.
"NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as
defined above).
Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment
and industrial robots.
Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support).
Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems and medical equipment for life support, etc.
"Standard":
"Special":
"Specific":
User’s Manual U13731EJ3V0UM
4
Regional Information
• Device availability
• Ordering information
• Product release schedule
• Availability of related technical literature
• Development environment specifications (for example, specifications for third-party tools and
components, host computers, power plugs, AC supply voltages, and so forth)
• Network requirements
In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary
from country to country.
[GLOBAL SUPPORT]
http://www.necel.com/en/support/support.html
NEC Electronics America, Inc. (U.S.)
Santa Clara, California
Tel: 408-588-6000
800-366-9782
NEC Electronics Hong Kong Ltd.
Hong Kong
Tel: 2886-9318
NEC Electronics Hong Kong Ltd.
Seoul Branch
Seoul, Korea
Tel: 02-558-3737
NEC Electronics Shanghai, Ltd.
Shanghai, P.R. China
Tel: 021-6841-1138
NEC Electronics Taiwan Ltd.
Taipei, Taiwan
Tel: 02-2719-2377
NEC Electronics Singapore Pte. Ltd.
Novena Square, Singapore
Tel: 6253-8311
J03.4
N
EC Electronics (Europe) GmbH
Duesseldorf, Germany
Tel: 0211-65 03 01
• Sucursal en España
Madrid, Spain
Tel: 091-504 27 87
Vélizy-Villacoublay, France
Tel: 01-30-67 58 00
• Succursale Française
• Filiale Italiana
Milano, Italy
Tel: 02-66 75 41
• Branch The Netherlands
Eindhoven, The Netherlands
Tel: 040-244 58 45
• Tyskland Filial
Taeby, Sweden
Tel: 08-63 80 820
• United Kingdom Branch
Milton Keynes, UK
Tel: 01908-691-133
Some information contained in this document may vary from country to country. Before using any NEC
Electronics product in your application, pIease contact the NEC Electronics office in your country to
obtain a list of authorized representatives and distributors. They will verify:
User’s Manual U13731EJ3V0UM 5
Major Revisions in This Edition
Page Description
Throughout Change of interface board for desktop PC from IE-70000-PCI-IF to IE-70000-PCI-IF-A
p.12 Modification of Figure 1-1 IE-78K0-NS System Configuration
p.36 A.1 Introduction
•Deletion of Applicable models
p.38 B.1 Introduction
•Deletion of Applicable models
The mark shows major revised points.
User’s Manual U13731EJ3V0UM
6
INTRODUCTION
Product overview The IE-78K0-NS is used in combination with an emulation board (IE-780×××-NS-EM1,
IE-780×××-NS-EM4), I/O board (IE-78K0-NS-P0×), and performance board (IE-78K0-
NS-PA) to debug products in the 78K/0 Series of 8-bit single-chip microcontrollers.
Target readers This manual is intended for engineers who perform debugging of systems that employ
78K/0 Series 8-bit single-chip microcontrollers with the IE-78K0-NS and an emulation
board (IE-780×××-NS-EM1, IE-780×××-NS-EM4), I/O board (IE-78K0-NS-P0×), and
performance board (IE-78K0-NS-PA).
Purpose The purpose of this manual is to help the user understand the debugging functions that
are available by using the IE-78K0-NS and the emulation board (IE-780×××-NS-EM1,
IE-780×××-NS-EM4), I/O board (IE-78K0-NS-P0×), and performance board (IE-78K0-
NS-PA) together.
Organization When using the IE-78K0-NS, please refer to the manual that comes with the IE-78K0-
NS (this manual) as well as the manual that comes with the emulation board (IE-
780×××-NS-EM1, IE-780×××-NS-EM4), I/O board (IE-78K0-NS-P0×), and performance
board (IE-78K0-NS-PA).
• Basic specifications • Function outline
• System configuration • Target interface differences
• External interface function
How to read this manual To understand the overall functions of the IE-78K0-NS:
→ Read this manual in the order of the contents.
To understand the basic specifications:
→ Refer to CHAPTER 1 GENERAL and CHAPTER 2 PART NAMES.
For how to connect the IE-780×××-NS-EM1, IE-780×××-NS-EM4, IE-78K0-NS-P0×, IE-
78K0-NS-PA and make settings to debug 78K/0 Series products:
→ Refer to CHAPTER 3 INSTALLATION.
IE-78K0-NS
User’s Manual
(This manual)
IE-780×××-NS-EM1
IE-780×××-NS-EM4
IE-78K0-NS-P0×
IE-78K0-NS-PA
User’s Manual
User’s Manual U13731EJ3V0UM 7
Terminology The meanings of the terms used in this manual are described in the table below.
Term Meaning
Emulation device This is a general term that refers to the device in the emulator that is used to
emulate the target device. It includes the emulation CPU.
Emulation CPU This is the CPU block in the emulator that is used to execute user-generated
programs.
Target device This is the device to be emulated.
Target program This is the program to be debugged.
Target system This is the system to be debugged.
This includes the target program and the hardware provided by the user.
When defined narrowly, it includes only the hardware.
Conventions Data significance: Higher digits on the left and lower digits on the right
Note: Footnote for item marked with Note in the text
Caution: Information requiring particular attention
Remark: Supplementary information
Related Documents Please use the following documents in conjunction with this manual.
The related documents listed below may include preliminary versions. However,
preliminary versions are not marked as such.
{Documents Related to Development Tools (User’s Manuals)
Document Name Document Number
IE-78K0-NS In-Circuit Emulator This manual
Operation U14445E
Language U14446E
RA78K0 Assembler Package
Structured Assembly Language U11789E
Operation U14297ECC78K0 C Compiler Package
Language U14298E
Operation (WindowsTM Based) U15373ESM78K Series Ver.2.30 or later System Simulator
External part user open
interface specifications
U15802E
ID78K Series Integrated Debugger Ver.2.30 or
later
Operation (Windows Based) U15185E
ID78K0 Integrated Debugger (EWS Based) Reference −
Basics U11537ERX78K0 Real-Time OS
Installation U11536E
Project Manager Ver. 3.12 or later (Windows Based) U14610E
PG-FP4 Flash Memory Programmer U15260E
Caution The documents listed above are subject to change without notice. Be sure to use the latest
documents for designing, etc.
User’s Manual U13731EJ3V0UM
8
CONTENTS
CHAPTER 1 GENERAL............................................................................................................................11
1.1 System Configuration....................................................................................................................11
1.2 Hardware Configuration ................................................................................................................13
1.3 Basic Specifications ......................................................................................................................15
1.4 Contents in Carton.........................................................................................................................17
CHAPTER 2 PART NAMES.....................................................................................................................19
2.1 Parts of Main Unit ..........................................................................................................................19
2.2 Board Name....................................................................................................................................21
CHAPTER 3 INSTALLATION ...................................................................................................................23
3.1 Connection .....................................................................................................................................23
3.2 External Trigger Functions ...........................................................................................................32
3.3 Jumper Settings (on Main Board (G-780009 Board)) .................................................................33
3.4 Low-Voltage Emulation Settings ..................................................................................................34
APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC .................................36
A.1 Introduction ....................................................................................................................................36
A.2 Installation ......................................................................................................................................37
APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A) ..................................................................38
B.1 Introduction ....................................................................................................................................38
B.2 Installation ......................................................................................................................................39
APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES ...............................40
C.1 Introduction ....................................................................................................................................40
C.2 Installation ......................................................................................................................................41
APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT COMPATIBLES ............43
D.1 Introduction ....................................................................................................................................43
D.2 Installation ......................................................................................................................................44
APPENDIX E REVISION HISTORY .........................................................................................................46
User’s Manual U13731EJ3V0UM 9
LIST OF FIGURES
Figure Number Title Page
1-1 IE-78K0-NS System Configuration .................................................................................................................... 12
1-2 IE-78K0-NS Basic Hardware Configuration 1.................................................................................................... 13
1-3 IE-78K0-NS Basic Hardware Configuration 2.................................................................................................... 13
1-4 IE-78K0-NS Basic Hardware Configuration 3.................................................................................................... 14
1-5 IE-78K0-NS Basic Hardware Configuration 4.................................................................................................... 14
1-6 Contents in Carton............................................................................................................................................. 17
1-7 Contents in Accessory Bag ............................................................................................................................... 18
2-1 Main Board (G-780009 Board) .......................................................................................................................... 22
3-1 Connecting Emulation Board (IE-780×××-NS-EM1) .......................................................................................... 24
3-2 Connecting Performance Board and Emulation Board (IE-780×××-NS-EM1) .................................................. 25
3-3 Connecting I/O Board and Emulation Board (IE-780×××-NS-EM4) ................................................................... 27
3-4 Connecting Performance Board, I/O Board and Emulation Board ................................................................... 28
3-5 Connecting Emulation Probe............................................................................................................................. 30
3-6 Connecting AC Adapter..................................................................................................................................... 31
3-7 Connecting Dedicated Bus Interface Cable....................................................................................................... 31
3-8 Default Settings of JP2, JP3, JP4, JP6, JP7, and JP8 ...................................................................................... 33
3-9 Part Names of G-780009 Board ........................................................................................................................ 34
3-10 Position of TP1 on IE-78K0-NS ......................................................................................................................... 34
3-11 Position of TP1 on IE-78018-NS-EM1............................................................................................................... 35
A-1 Mounting of PCI Board and Connector Boards ................................................................................................. 37
C-1 INT JP, WAIT JP Settings ................................................................................................................................. 42
D-1 INT JP, WAIT JP Settings ................................................................................................................................. 45
User’s Manual U13731EJ3V0UM
10
LIST OF TABLES
Table Number Title Page
1-1 List of Functions (MAX. Specifications) .............................................................................................................15
3-1 Electrical Specifications .....................................................................................................................................32
C-1 SW1 and SW2 Settings When Setting I/O Address to 01D×H...........................................................................41
D-1 SW1 and SW2 Settings When Setting I/O Address to 020×H ...........................................................................44
User’s Manual U13731EJ3V0UM 11
CHAPTER 1 GENERAL
The IE-78K0-NS is a development tool for effectively debugging hardware and software in which a 78K/0 Series 8-
bit single-chip microcontroller is used.
This chapter describes the system configuration and basic specifications of the IE-78K0-NS.
1.1 System Configuration
Figure 1-1 shows the system configuration of the IE-78K0-NS.
CHAPTER 1 GENERAL
User’s Manual U13731EJ3V0UM
12
Figure 1-1. IE-78K0-NS System Configuration
Integrated debugger
ID78K0-NS
(sold separately)
Device file
Note 4
(available separately)
Interface board
IE-70000-98-IF-C
(sold separately)
Interface board
IE-70000-PC-IF-C
(sold separately)
Interface board
IE-70000-PCI-IF-A
(sold separately)
or
IE-78K0-NS
(this product)
PC card interface
+
++
+
Performance board
IE-78K0-NS-PA
Emulation board
IE-78×××-NS-EM1
(sold separately)
AC adapter
IE-70000-MC-PC-B
(sold separately)
I/O board
IE-78K0-NS-P0×
(sold separately)
Emulation board
IE-780×××-NS-EM4
(sold separately)
Control software
Host machine
PC-9800 series,
IBM PC/AT
TM
compatibles
Interface
cable
NS card
cable
MC card
cable
Note 5
PC card interface
IE-70000-CD-IF-A
(sold separately)
Interface cable
(NS interface cable)
In-circuit emulator
Emulation probe
NP-××××
Note 2
(sold separately)
Convertion socket
EV-×××××-××
TQx-××××××
Note 3
Notes 1. When using the IE-780×××-NS-EM4, it is necessary to connect an I/O board, IE-78K0-NS-P0×. The
IE-780×××-NS-EM4 and IE-78K0-NS-P0× are sold separately.
2. The NP-××××× is a product of Naito Densei Machida Mfg. Co., Ltd.
For further information, contact Naito Densei Machida Mfg. Co., Ltd. (TEL: +81-45-475-4191)
3. The TQx-xxxxxx are products of TOKYO ELETECH CORPORATION.
For further information, contact Daimaru Kogyo Co., Ltd.
Tokyo Electronics Department (TEL: +81-3-3820-7112)
Osaka Electronics Department (TEL: +81-6-6244-6672)
CHAPTER 1 GENERAL
User’s Manual U13731EJ3V0UM 13
Notes 4. The device file can be downloaded from the NEC Electronics website
(URL: http://www.necel.com/micro).
5. This is a cable for the V850 Series. This is not used for the IE-78K0-NS.
1.2 Hardware Configuration
The IE-78K0-NS consists of the following hardware units (such as cabinet and boards).
• Cabinet
• 78K0 main board
• NS interface cable
• Plastic spacers × 2
Figure 1-2. IE-78K0-NS Basic Hardware Configuration 1
IE-78K0-NS
Host
machine
Interface board
(sold separately)
Interface card
(sold separately)
Dedicated
bus interface
78K0
main board
78K0 Series
EM1 board
Emulation probe
(sold separately)
Figure 1-3. IE-78K0-NS Basic Hardware Configuration 2
IE-78K0-NS
78K0
option board
78K0 Series
EM1 board
Host
machine
Interface board
(sold separately)
Interface card
(sold separately)
Dedicated bus
interface
78K0
main board
External sense
probe
Emulation probe
(sold separately)
CHAPTER 1 GENERAL
User’s Manual U13731EJ3V0UM
14
Figure 1-4. IE-78K0-NS Basic Hardware Configuration 3
IE-78K0-NS
Host
machine
Interface board
(sold separately)
Interface card
(sold separately)
Dedicated bus
interface
78K0
main board
Emulation board 2
(IE-78K0-NS-P0×)
78K0 Series
EM4 board
Emulation probe
(sold separately)
Figure 1-5. IE-78K0-NS Basic Hardware Configuration 4
Host
machine
Interface board
(sold separately)
Interface card
(sold separately)
Dedicated bus
interface
78K0
main board
78K0
option board
Emulation
board 2
(IE-78K0
-NS-P0×)
78K0 Series
EM4 board
Emulation probe
(sold separately)
External sense
probe
CHAPTER 1 GENERAL
User’s Manual U13731EJ3V0UM 15
1.3 Basic Specifications
Table 1-1. List of Functions (MAX. Specifications) (1/2)
Parameter Description
Supervisor V40TM (operating frequency: 16.0 MHZ)
Target device 78K/0 Series (
µ
PD780×××)
System clock According to specification of emulation board (sold separately)
External Pulse inputClock
supply Internal Mounted on emulation board (sold separately)
Substitute memory capacity 64 KB
Internal ROM 4 KB
Internal high-
speed RAM
64 bytes
Internal low-speed
RAM
128 bytes
Mapping
unit
External expansion
memory
8 KB
Emulation function • Real-time execution
• Break execution
• Step execution
Real-time internal RAM monitor 2 KB of memory space
Event detection • Program execution detection
• Bus event detection
• External trigger detection
Trigger output (open drain output (1))
Event integration • Path condition
• Trace qualify condition
• Delay condition
• Trigger condition
Break factor • Event break
• Manual break
• Command break
• Fail-safe break
Trace factor • All traces
• Qualify trace
Trace capacity 32 bits × 8 KB
Real-time trace
Trace content Address, data, and status
CHAPTER 1 GENERAL
User’s Manual U13731EJ3V0UM
16
Table 1-1. List of Functions (MAX. Specifications) (2/2)
Parameter Description
Execution time measurement Up to 4 mins 28 sec, resolution: 62.5 ns
Target interface Emulation probe (sold separately) provided for each target device shape
Host interface Dedicated bus interface
Low-voltage support Based on the emulation board (sold separately)
Host machine PC-9800 series, or IBM PC/AT compatibles
Power supply DC 5 V
Operation temperature range 10°C to 40°C
Dimensions W240 × D197 × H73 (mm)
CHAPTER 1 GENERAL
User’s Manual U13731EJ3V0UM 17
1.4 Contents in Carton
The IE-78K0-NS carton contains the main unit, cables, an accessory bag, and a guarantee card.
Make sure that the accessory bag contains a packing list, this user’s manual, spacers, and screws.
In case of missing or damaged items, please contact an NEC Electronics sales representative or NEC Electronics
distributor.
Figure 1-6. Contents in Carton
<2> NS interface cable <3> FG cable
<4> Accessory bag
<1> IE-78K0-NS
<5> Guarantee card
<1> IE-78K0-NS main unit × 1
<2> NS interface cable × 1
<3> FG cable × 1
<4> Accessory bag × 1
<5> Guarantee card × 1
CHAPTER 1 GENERAL
User’s Manual U13731EJ3V0UM
18
Check that the accessory bag contains the following items (refer to Figure 1-7 Contents in Accessory Bag).
<a> Packing list × 1
<b> User’s manual (this manual) × 1
<c> Spacers × 2
<d> Screws × 4
Figure 1-7. Contents in Accessory Bag
<a> Packing list
<b> User's manual
<c> Spacers
<d> Screws
User’s Manual U13731EJ3V0UM 19
CHAPTER 2 PART NAMES
This chapter introduces the parts of the IE-78K0-NS main unit.
The packing box contains the IE-78K0-NS main unit. If there are any missing or damaged items, please contact
an NEC sales representative.
Please make sure to fill out and return the guarantee card that comes with the main unit.
2.1 Parts of Main Unit
(1) Probe end
T V C C
Target system power supply LED
Probe interface
Small: 13 × 158 mm
Large: 16 × 158 mm
(2) Top view
POWER
IN CIRCUIT EMULATOR
Power supply LED
CHAPTER 2 PART NAMES
User’s Manual U13731EJ3V0UM
20
(3) Interface
FG OFF ON RESET HOST-I/F
DC IN
-+
Reset switch
(RESET)
Dedicated bus interface connector
(HOST-I/F)
Power switch
(OFF/ON)
CHAPTER 2 PART NAMES
User’s Manual U13731EJ3V0UM 21
2.2 Board Name
The IE-78K0-NS contains the following board.
• Main board (G-780009 Board) × 1
Check that you have the correct board. To access the inside of the unit, remove the four screws from the sides of
the main unit and open the lid.
CHAPTER 2 PART NAMES
User’s Manual U13731EJ3V0UM
22
Figure 2-1. Main Board (G-780009 Board)
Remark The main board is shown mounted in the main unit
User’s Manual U13731EJ3V0UM 23
CHAPTER 3 INSTALLATION
This chapter describes how to connect the cables to the IE-78K0-NS and the mode settings.
3.1 Connection
Connect the following ten products, which are sold separately.
Refer to Figure 1-1 System Configuration of IE-78K0-NS in CHAPTER 1 GENERAL for the system configuration
of the IE-78K0-NS.
• IE-70000-98-IF-C: Interface board (use cable that comes with IE-78K0-NS)
• IE-70000-PC-IF-C: Interface board (use cable that comes with IE-78K0-NS)
• IE-70000-PCI-IF-A: Interface board (use cable that comes with IE-78K0-NS)
• IE-70000-CD-IF-A: PC card interface (use NS card cable)
• IE-70000-MC-PS-B: AC adapter
• IE-780×××-NS-EM1: Emulation board
• IE-780×××-NS-EM4: Emulation board
• IE-78K0-NS-P0×: I/O board
• IE-78K0-NS-PA: Performance board
• NP-×××××: Emulation probe
Caution Connecting and removing cables or components from the target system and changing the
settings of switches, etc. should be carried out after turning off the power of the IE-78K0-NS
main unit and the target system.
CHAPTER 3 INSTALLATION
User’s Manual U13731EJ3V0UM
24
(1) Connecting emulation board (IE-780×××
××××××
×××-NS-EM1)
The IE-780×××-NS-EM1 is sold separately.
Figure 3-1. Connecting Emulation Board (IE-780×××
××××××
×××-NS-EM1)
<1> Remove the screws from the sides of the
main unit, and then remove the top cover.
<3> Replace the spacers (metal) of the main
board, as indicated in the diagram below,
with the spacers (plastic) attached to the IE-
78K0-NS.
Caution This procedure is needed only
when using the IE-78018-NS-
EM1.
<5> When using a probe, connect the probe.
<2> Remove the first plate from the bottom by
removing the screws.
<4> Connect the IE-780×××-EM1 and fasten the
two screws to the emulation board.
<6> Replace the top cover and fasten the four
screws on the sides.
;;;
;;
;
;
;
;;
Here
Emulation board
;
;
;
;
;;
;;
Refer to (5) for the probe
connection method.
CHAPTER 3 INSTALLATION
User’s Manual U13731EJ3V0UM 25
(2) Connecting performance board (IE-78K0-NS-PA) and emulation board (IE-780×××
××××××
×××-NS-EM1)
The IE-78K0-NS-PA and IE-780×××-NS-EM1 are sold separately.
Figure 3-2. Connecting Performance Board and Emulation Board (IE-780×××
××××××
×××-NS-EM1) (1/2)
<1> Remove the screws from the sides of the
main unit, and then remove the top cover.
<3> Connect the IE-78K0-NS-PA and affix the
attached spacers to the IE-78K0-NS-PA at
five points on the board.
<5> Connect the IE-78×××-NS-EM1 on the IE-
78K0-NS-PA and fasten the two screws.
<2> Remove the first and second plates from the
bottom by removing the screws.
<4> When only connecting the IE-78018-NS-EM1
on the IE-78K0-NS-PA, remove spacer 1
(metal) of the following figure and replace
spacers 2 and 3 (metal) with the attached
spacers (plastic).
<6> When using a probe, connect the probe.
Here
IE-78K0-NS-PA
Attached
spacer Attached
spacer
Fix
Fix
Spacers 2 and 3
Spacer 1
IE-780×××-NS-EM1
IE-78K0-NS-PA
Refer to (5) for the probe
connection method.
Refer to the IE-78K0-NS-PA
User's Manual for the
EXT cable connection method.
CHAPTER 3 INSTALLATION
User’s Manual U13731EJ3V0UM
26
Figure 3-2. Connecting Performance Board and Emulation Board (IE-780×××
××××××
×××-NS-EM1) (2/2)
<7> Replace the top cover and fasten the four
screws on the sides.
IE-780×××-NS-EM1
IE-78K0-NS-PA
CHAPTER 3 INSTALLATION
User’s Manual U13731EJ3V0UM 27
(3) Connecting I/O board (IE-78K0-NS-P0×
××
×) and emulation board (IE-78K0-NS-P0×
××
× and IE-780×××
××××××
×××-NS-EM4)
The IE-78K0-NS-P0× and IE-780×××-NS-EM4 are sold separately.
Figure 3-3. Connecting I/O Board and Emulation Board (IE-780×××
××××××
×××-NS-EM4)
<1> Remove the screws from the sides of the
main unit, and then remove the top cover.
<3> Connect the IE-78K0-NS-P0× to the main
board. Fix the attached spacers to the IE-
78K0-NS-P0× at the four corners of the
board.
<5> When using a probe, connect the probe.
<2> Remove the second plate from the bottom
by removing the screws.
<4> Connect the IE-780×××-NS-EM4 on the IE-78K0-
NS-P0×, and fasten the screws at the four
corners.
<6> Replace the top cover and fasten the four
screws on the sides.
;;;
;
;
;
;
;;
;;
Refer to (5) for the probe
connection method.
;
;
;
;
;
;
;;
;;
IE-78K0-NS-P0×
;
Fix
Attached
spacer
;
Attached
spacer
Fix
;;;
;;
;
;
;
;
;
;
;
;
;
IE-78K0-NS-P0×
IE-780×××-NS-EM4
IE-78K0-NS-P0×
IE-780×××-NS-EM4
CHAPTER 3 INSTALLATION
User’s Manual U13731EJ3V0UM
28
(4) Connecting performance board (IE-78K0-NS-PA), I/O board (IE-78K0-NS-P0×
××
×) and emulation board (IE-
780×××
××××××
×××-NS-EM1 and IE-78K×××
××××××
×××-NS-EM4)
The IE-78K0-NS-PA, IE-78K0-NS-P0×, and IE-780×××-NS-EM4 are sold separately.
Figure 3-4. Connecting Performance Board, I/O Board and Emulation Board (1/2)
<1> Remove the screws from the sides of the
main unit, and then remove the top cover.
<3> Connect the IE-78K0-NS-PA and affix the
attached spacers to the IE-78K0-NS-PA at
five points on the board.
<5> Connect the IE-780×××-NS-EM4 on the IE-
78K0-NS-P0×, and fasten the screws at the
four corners.
<2> Remove the first and third plates from the
bottom by removing the screws.
<4> Connect the IE-78K0-NS-P0× on the IE-
78K0-NS-PA, and fix the spacers to the IE-
78K0-NS-P0× at the four corners.
<6> When using a probe, connect the probe.
IE-78K0-NS-PA
IE-78K0-NS-P0×
IE-78K0-NS-PA
Attached
spacer Attached
spacer
Fix Fix
Here
Attached
spacer
Attached
spacer
FixFix
IE-78×××-NS-EM4
IE-78K0-NS-PA
IE-78K0-NS-P0×Refer to (5) for the probe
connection method.
Refer to the IE-78K0-NS-PA
User's Manual for the
EXT cable connection method.
CHAPTER 3 INSTALLATION
User’s Manual U13731EJ3V0UM 29
Figure 3-4. Connecting Performance Board, I/O Board and Emulation Board (2/2)
<7> Replace the top cover and fasten the four
screws on the sides.
IE-78K0×××-NS-P0×
IE-78K0-NS-PA
IE-78×××-NS-EM4
CHAPTER 3 INSTALLATION
User’s Manual U13731EJ3V0UM
30
(5) Connecting emulation probe (NP-×××××
××××××××××
×××××)
The NP-××××× is sold separately.
Figure 3-5. Connecting Emulation Probe
IE-78K0-NS-P0×
(this is necessary only
when mounting the
IE-780×××-NS-EM4)
IE-78K0-NS-PA
Emulation probe
(NP-×××××)
Emulation probe
(NP-×××××)
IE-780×××-NS-EMn
(n = 1, 4)
IE-780×××-NS-EMn
(n = 1, 4)
Main board
(G-780009 board)
Main board
(G-780009 board)
IE-78K0-NS-P0×
(this is necessary only
when mounting the
IE-780×××-NS-EM4)
Caution The emulation probe (NP-×××××
××××××××××
×××××) mounting location varies depending on the model of the IE-
780×××
××××××
×××-NS-EMn (n = 1 or 4) in use. For details, refer to the IE-780×××
××××××
×××-NS-EMn User’s Manual.
CHAPTER 3 INSTALLATION
User’s Manual U13731EJ3V0UM 31
(6) Connecting AC adapter (IE-70000-MC-PS-B)
The IE-70000-MC-PS-B is sold separately.
<1> Insert the AC adapter plug into the DC IN socket of the IE-78K0-NS.
Figure 3-6. Connecting AC Adapter
FG OFF ON RESET HOST-I/F
DC IN
-
+
Reset switch
(RESET)
Dedicated bus interface connector
(HOST-I/F)
Power switch
(OFF/ON)
(7) Connecting interface cable
<1> Insert the cable into the bus interface connector on the IE-78K0-NS main unit.
Figure 3-7. Connecting Dedicated Bus Interface Cable
FG OFF ON RESET HOST-I/F
DC IN
-
+
Reset switch
(RESET)
Dedicated bus interface connector
(HOST-I/F)
Power switch
(OFF/ON)
Caution The type of interface cable varies depending on whether an interface board or a PC card
interface is used.
•
••
• When using an interface board (IE-70000-98-IF-C, IE-70000-PC-IF-C, or IE-70000-PCI-IF-A)
→
→→
→ Connect the NS interface cable that comes with the IE-78K0-NS.
•
••
• When using a PC card interface (IE-70000-CD-IF-A)
→
→→
→ Connect the NS card cable that comes with the IE-70000-CD-IF-A.
The IE-70000-98-IF-C, IE-70000-PC-IF-C, IE-70000-PCI-IF-A, and IE-70000-CD-IF-A are sold
separately.
CHAPTER 3 INSTALLATION
User’s Manual U13731EJ3V0UM
32
3.2 External Trigger Functions
(1) EXTOUT
At the occurrence of a break event, the EXTOUT pin on the emulation board outputs a low level for 1.3
µ
s.
Caution Because the output is open drain, connect a pull-up resistor in the target system.
(2) EXTIN
The EXTIN pin on the emulation board can be used to input an event signal. Enter high-level pulse signals for
two or more CPU clocks.
Caution For the electrical specifications, refer to Table 3-1.
Table 3-1. Electrical Specifications
Parameter MIN. [V] MAX. [V]
High-level input voltage Target voltage × 0.7 Target voltage
Low-level input voltage 0 Target voltage × 0.3
CHAPTER 3 INSTALLATION
User’s Manual U13731EJ3V0UM 33
3.3 Jumper Settings (on Main Board (G-780009 Board))
(1) Default jumper settings
Figure 3-8. Default Settings of JP2, JP3, JP4, JP6, JP7, and JP8
135
24
JP6
6
123
JP2
123
JP3
123
JP4
135
24
JP8
6
135
24
JP7
6
JP8: Selection of the subsystem clock source (default setting: 1 and 2 shorted)
1 and 2 shorted: Internal (mounted on the emulation board or mounted on the part board by
the user)
3 and 4 shorted: External (input via an emulation probe from the target system)
Caution Jumper settings differ depending on the emulation board. For details, refer to the
relevant emulation board user’s manual.
CHAPTER 3 INSTALLATION
User’s Manual U13731EJ3V0UM
34
Figure 3-9. Part Names of G-780009 Board
CN7
JP6
JP4
JP3
P2
CN6
JP2TP1
JP8JP7
CN5
P1
CN4
3.4 Low-Voltage Emulation Settings
Low-voltage emulation can be executed in the IE-78K0-NS by connecting an emulation board that supports low-
voltage operation.
(1) When using other than the IE-78018-NS-EM1 when the target is at low voltage, supply the same supply voltage
as that of the target to the IE-78K0-NS TP1 terminal pin. (This also applies when the voltage is 5 V.)
Figure 3-10. Position of TP1 on IE-78K0-NS
CN7
P2
CN6
TP1
CN5
P1
CN4
Remark The maximum current consumption of TP1 is from 100 mA (1.8 V) to 300 mA (5 V).
CHAPTER 3 INSTALLATION
User’s Manual U13731EJ3V0UM 35
(2) When using the IE-78018-NS-EM1 when the target is at low voltage, supply the same supply voltage as that of
the target to the TP1 terminal pin on the IE-78018-NS-EM1. (This also applies when the voltage is 5 V.)
Figure 3-11. Position of TP1 on IE-78018-NS-EM1
CN1 CN2
TP1
Remark The maximum current consumption of TP1 is from 100 mA (1.8 V) to 300 mA (5 V).
Caution For details of the target voltage or maximum current consumption, refer to the relevant
emulation board user’s manual.
User’s Manual U13731EJ3V0UM
36
APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC
This chapter describes the setting method when connecting the IE-78K0-NS.
For details, refer to the IE-70000-PCI-IF-A User’s Manual (to be prepared).
A.1 Introduction
The IE-70000-PCI-IF-A is an interface board for an IE product that is installed in the PCI bus slot of a PC.
First of all, check that you have the following items.
• Interface board (IE-70000-PCI-IF-A) for desktop PC × 1
• 8-bit connector board (connected to IE-70000-PCI-IF-A) × 1
• 32-bit connector board × 1
• User’s manual × 1
• DLL-DISK × 1
• DRV-DISK × 1
<Basic specifications>
Hardware resources used
• I/O address .........0000H to FFFFH
• Interrupts ............Unused
• Memory...............Uses 80 bytes
Current consumption
300 mA (MAX. when using +5 V)
Cautions 1. Do not place heavy objects on or apply pressure to the board.
2. Do not drop the board or subject it to excessive vibration or shock.
3. When removing a cable, do not pull it by the cord.
4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it
is directly exposed to sunlight.
5. Avoid subjecting the board to extreme changes in temperature or humidity.
6. Do not spill drinks or other liquids onto the board or its accessories.
7. Do not connect a cable for a different product to the connector.
APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC
User’s Manual U13731EJ3V0UM 37
A.2 Installation
(1) Board settings
There are no jumpers or DIP switches on the IE-70000-PCI-IF-A.
(2) 8-bit connector board mounting
An 8-bit connector board is premounted at shipment.
Remark When a 32-bit board is mounted, place it on the 8-bit connector board using the combination connector
(refer to Figure A-1) and fasten them together.
Caution The 32-bit connector board is attached for future function expansion.
Figure A-1. Mounting of PCI Board and Connector Boards
CH1 CH0
PCI board
32-bit connector board
Combination connector
Combination connector
Combination connector
8-bit connector board
(3) Installation in PC
Make sure that the PC is turned off, then install the interface board in the PCI bus slot following the instructions in
the PC’s manual.
(4) PCI driver installation
Refer to the supplied DRV_DISK Readme_e.txt for PCI driver installation.
(5) Connecting with IE-78K0-NS
Using the supplied cable, connect the IE-78K0-NS to the CH0 side.
Caution Connection with the IE-78K0-NS is possible on the CH0 side only.
User’s Manual U13731EJ3V0UM
38
APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A)
This chapter describes the setting method when connecting the IE-78K0-NS.
For details, refer to the IE-70000-CD-IF-A User’s Manual (to be prepared).
B.1 Introduction
The PC card interface (IE-70000-CD-IF-A) is an interface card for an IE product that is installed in a PC PCI bus
slot compliant with PCMCIA2.1/JEIDA standard Ver. 4.2.
Check that you have the following items.
• PC card interface (IE-70000-CD-IF-A) × 1
• MC-A CABLE × 1
• NS-A CABLE × 1
• User’s manual × 1
• DLL-DISK × 1
• DRV-DISK × 1
<Basic specifications>
Hardware resources used
• I/O address .........20 bytes starting from 220H, 260H, 2E0H, 320H, or 3E0H as a base address
• Interrupts ............Unused
• Memory...............Unused
Current consumption
300 mA (MAX. when using +5 V)
Cautions 1. Do not place heavy objects on or apply pressure to the board.
2. Do not drop the board or subject it to excessive vibration or shock.
3. When removing a cable, do not pull it by the cord.
4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it
is directly exposed to sunlight.
5. Avoid subjecting the board to extreme changes in temperature or humidity.
6. Do not spill drinks or other liquids onto the board or its accessories.
7. Do not connect a cable for a different product to the connector.
APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A)
User’s Manual U13731EJ3V0UM 39
B.2 Installation
(1) Installation in PC
Insert the PCMCIA card in the card slot when the power supply of the PC is turned on.
For Windows NT4.0, insert the card in the slot when the power supply is turned off. Be careful to insert the card
in the correct direction.
(2) PCMCIA driver installation
Refer to the supplied DRV-DISK Readme_e.txt for PCMCIA driver installation.
Caution This interface card cannot be connected to the IE-78××××
××××××××
××××-R. Actually, installation ends
completely by selecting “IE-78××××
××××××××
××××-R” displayed in the DRV-DISK install menu. In this case,
however, the installation is invalid.
(3) Connection with the IE-78K0-NS
Using the NS-A CABLE, connect the IE-70000-CD-IF-A to the IE-78K0-NS.
Caution Be sure to use the NS-A CABLE when connecting to the IE-78K0-NS. If MC-A is used, the IE-
70000-CD-IF-A may be damaged.
User’s Manual U13731EJ3V0UM
40
APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES
This chapter describes the setting method when connecting the IE-78K0-NS.
For details, refer to the IE-70000-98-IF-C User’s Manual (to be prepared).
C.1 Introduction
The IE-70000-98-IF-C is an interface board for an IE product that is installed in the C bus slot of a PC9800 series
machine.
Caution The PC98-NX series is treated as an IBM PC/AT compatible machine. Refer to APPENDIX A
INTERFACE BOARD (IE-70000-PCI-IF(-A)) FOR DESKTOP PC.
First of all, check that you have the correct interface board.
• Interface board (IE-70000-98-IF-C) for PC-9800 series × 1
<Basic specifications>
Applicable models
This product is designed for devices incorporating a PC-9800 series C bus.
Hardware resources used
• I/O addresses .............. 16 bytes at a 256-byte boundary (00D×H, 01D×H,...FFD×H)
• Interrupts and others ... Unused
Current consumption
500 mA (MAX. when using +5 V)
Cautions 1. Do not place heavy objects on or apply pressure to the board.
2. Do not drop the board or subject it to excessive vibration or shock.
3. When removing a cable, do not pull it by the cord.
4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it
is directly exposed to sunlight.
5. Avoid subjecting the board to extreme changes in temperature or humidity.
6. Do not spill drinks or other liquids onto the board or its accessories.
7. Do not connect a cable for a different product to the connector.
APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES
User’s Manual U13731EJ3V0UM 41
C.2 Installation
(1) I/O address settings
SW1 and SW2 are the switches selecting the C bus I/O addresses. SW1 numbers 1 to 8 correspond to C bus
addresses A4 to A11, and SW2 numbers 1 to 4 correspond to C bus addresses A12 to A15.
In the IE-78K0-NS, the addresses should be set in the 16 bytes between 00D×H and FFD×H. The switch takes
the value “0” when ON and “1” when OFF.
The addresses used for setup must be values that are not used in the PC system or for other boards. In
addition, since these values are used during software installation, make a note of them for future reference.
Setting examples of I/O address, SW1 and SW2 are shown below.
Table C-1. SW1 and SW2 Settings When Setting I/O Address to 01D×
××
×H
SW1 Number12345678
Address A4 A5 A6 A7 A8 A9 A10 A11
ON 0 000
OFF 1 1 1 1
SW2 Number12345678
Address A12 A13 A14 A15 OFF OFF ON OFF
ON 0 000 0
OFF 1 1 1
Caution Use the default setting for SW1 numbers 1 to 4.
APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES
User’s Manual U13731EJ3V0UM
42
(2) Jumper settings
The INT JP and WAIT JP are C bus interrupt and WAIT selection jumpers.
In the IE-78K0-NS, set INT JP to NO USE, and WAIT JP to 1 and 2 shorted.
Figure C-1. INT JP, WAIT JP Settings
12
WAIT JP
3
: Shorted
12
INT JP
ShortedNO USE
IR3
IR5
IR6
IR9
IR11
IR12
IR13
(3) Installation in PC
Make sure that the PC is turned off, then install the interface board in the C bus slot following the instructions in
the PC’s manual.
(4) Connecting with IE-78K0-NS
Using the supplied cable, connect the IE-78K0-NS to the CH0 side.
Caution Connection with the IE-78K0-NS is possible on the CH0 side only.
For connection with other models, refer to their respective manuals.
User’s Manual U13731EJ3V0UM 43
APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT COMPATIBLES
This chapter describes the setting method when connecting the IE-78K0-NS.
For details, refer to the IE-70000-PC-IF-C User’s Manual (to be prepared).
D.1 Introduction
The IE-70000-PC-IF-C is an interface board for IBM PC/AT compatibles that is installed in the ISA bus slot of an
IBM PC/AT compatible.
First of all, check that you have the correct interface board.
• Interface board (IE-70000-PC-IF-C) for IBM PC/AT × 1
<Basic specifications>
Applicable models
The IE-70000-PC-IF-C is designed for IBM PC/AT compatibles incorporating an ISA bus.
Hardware resources
• I/O address.................. 16 bytes at any 16-byte boundary (020×H to 03F×H)
• Interrupts and others ... Unused
Current consumption
500 mA (MAX. when using +5 V)
Cautions 1. Do not place heavy objects on or apply pressure to the board.
2. Do not drop the board or subject it to excessive vibration or shock.
3. When removing a cable, do not pull it by the cord.
4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it
is directly exposed to sunlight.
5. Avoid subjecting the board to extreme changes in temperature or humidity.
6. Do not spill drinks or other liquids onto the board or its accessories.
7. Do not connect a cable for a different product to the connector.
APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT COMPATIBLES
User’s Manual U13731EJ3V0UM
44
D.2 Installation
(1) I/O address settings
SW1 and SW2 are the switches selecting the ISA bus I/O addresses. SW1 numbers 1 to 8 correspond to ISA
bus addresses A4 to A11, and SW2 numbers 1 to 4 correspond to ISA bus addresses A12 to A15.
In the IE-78K0-NS, the addresses should be set between 020×H and 03F×H. The switch takes the value “0”
when ON and “1” when OFF.
The addresses used for setup must be values that are not used in the PC system or for other boards. In
addition, since these values are used during software installation, make a note of them for future reference.
Setting examples of I/O address, SW1 and SW2 are shown below.
Table D-1. SW1 and SW2 Settings When Setting I/O Address to 020×
××
×H
SW1 Number12345678
Address A4A5A6A7A8A9A10A11
ON 0 0000 00
OFF 1
SW2 Number12345678
Address A12 A13 A14 A15 OFF OFF ON OFF
ON 0 000 0
OFF 1 1 1
Caution Set SW2 number 7 to ON and SW2 numbers 5, 6, and 8 to OFF.
APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT COMPATIBLES
User’s Manual U13731EJ3V0UM 45
(2) Jumper Settings
The INT JP and WAIT JP are C bus interrupt and WAIT selection jumpers.
In the IE-78K0-NS, set INT JP to NO USE, and WAIT JP to 1 and 2 shorted.
Figure D-1. INT JP, WAIT JP Settings
12
WAIT JP
3
: Shorted
12
INT JP
NO USE Shorted
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
(3) Installation in PC
Make sure that the PC is turned off, then install the interface board in the ISA bus slot following the instructions
in the PC’s manual.
(4) Connecting with IE-78K0-NS
Using the supplied cable, connect the IE-78K0-NS to the CH0 side.
Caution Connection with the IE-78K0-NS is possible on the CH0 side only.
For connection with other models, refer to their respective manuals.
User’s Manual U13731EJ3V0UM
46
APPENDIX E REVISION HISTORY
A history of the revisions up to this edition is shown below. “Applied to:” indicates the chapters to which the
revision was applied.
Edition Major Revisions from Previous Edition Applied to:
Modification of Figure 1-1 IE-78K0-NS System Configuration
Modification of Figure 1-2 IE-78K0-NS Basic Hardware Configuration 1
Addition of 1.4 Contents in Carton
CHAPTER 1
GENERAL
Modification of 3.1 Connection CHAPTER 3
INSTALLATION
Addition of INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC APPENDIX A
Addition of PC CARD INTERFACE (IE-70000-CD-IF-A) APPENDIX B
2nd
Addition of REVISION HISTORY APPENDIX E
Change of interface board for desk top PC from IE-70000-PCI-IF to IE-70000-PCI-IF-A Throughout
Modification of Figure 1-1 IE-78K0-NS System Configuration CHAPTER 1
GENERAL
A.1 Introduction
•Deletion of Applicable models
APPENDIX A
3rd
B.1 Introduction
•Deletion of Applicable models
APPENDIX B
User’s Manual U13731EJ3V0UM 47
[MEMO]
