Model 0922B75-37AA Rev. A Xinger Balun 75 to 75 Balanced Description The 0922B75-37AA is a low cost, low profile sub-miniature unbalanced to balanced transformer designed for differential inputs and output locations on wireless chipsets in an easy to use surface mount package covering dual polarized commercial Satellite bands 950 MHz - 2150 MHz. The 0922B75-37AA is ideal for high volume manufacturing and is higher performance than traditional wire wound baluns. The 0922B75-37AA has an unbalanced port impedance of 75 and a 75 balanced port impedance*. This transformation enables single ended signals to be applied to differential ports on modern integrated chipsets. The output ports have equal amplitude (-3dB) with 180 degree phase differential. The 0922B75-37AA is available on tape and reel for pick and place high volume manufacturing. ELECTRICAL SPECIFICATIONS** Features: * * * * * * * * * * * 950 - 2150 MHz 180 Transformer 75 Ohm to 2 x 37.5 Ohm Low Insertion Loss Multi-band Cellular Apps Sat LNB Chipset Compliant No DC Decoupling Capacitors Required Input to Output DC Isolation Surface Mountable RoHS compliant Tape & Reel Frequency Unbalanced Port Impedance Balanced Port Impedance* Return Loss Insertion Loss MHz Ohms Ohms dB min dB max 950 - 2150 75 75 12 0.8*** Amplitude Balance Phase Balance Power Handling JC dB Degrees max Watts C / Watt C 0 0.7 180 10 4 TBD -55 to +85 Operating Temp. **Specification based on performance of unit properly installed on microstrip printed circuit boards with 75 + 37.5 nominal impedance. Spec's subject to change without notice. * 37.5 reference to ground *** Insertion Loss stated at room temperature (0.9 dB Max at +85 C) Outline Drawing Top View (Near-side) 3 .150.005 [3.810.13] 2 Side View 1 .059.006 [1.510.15] Orientation Marker Denotes Pin Location .150.005 [3.810.13] 4 5 6 Dimensions are in Inches [Millimeters] Mechanical Outline Bottom View (Far-side) 4X .020.004 [0.510.10] .125.004 [3.180.10] Pin 1 2 3 4 5 6 Designation In NC / DC GND Out 1 GND Out 2 6X .009.004 [0.240.10] 6X .030.004 [0.760.10] Tolerances are Non-Cumulative Available on Tape and Reel For Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 544-2414 +44 2392-232392 Model 0922B75-37AA Rev. A Typical Broadband Performance: 550 MHz. to 2550 MHz. Amplitude Balance Balanced and UnBalanced Return Loss 1 0.8 Amplitude Balance [dB] 0 Return Loss [dB] -5 -10 -15 -20 -25 -30 550 750 950 1150 1350 1550 1750 1950 2150 2350 2550 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 550 Fre que ncy [M Hz] Fre que ncy [M Hz] Insertion Loss Phase Balance 190 187.5 Phase Balance [Deg] Insertion Loss [dB] 0 -0.2 -0.4 -0.6 -0.8 -1 -1.2 -1.4 -1.6 -1.8 -2 550 750 950 1150 1350 1550 1750 1950 2150 2350 2550 185 182.5 180 177.5 175 172.5 170 550 750 950 1150 1350 1550 1750 1950 2150 2350 2550 750 950 1150 1350 1550 1750 1950 2150 2350 2550 Fre que ncy [M Hz] Fre que ncy [M Hz] Pin Configuration: The internal configuration of the Xinger(R) balun is diagramed to the left; the unbalanced port is DC connected to ground and the two balanced ports are DC connected and floating. For many chipset applications there is an opportunity to eliminate two decoupling capacitors and/or use a single bias point if applicable. Differential drive is popular in integrated circuit since it aids stability in the presence of bond wire and pin inductance, provides some degree of immunity to power supply and ground noise, and can provide higher output power in the case of some device limits. The construction of the Xinger(R) balun is bonded multi-layered stripline made of low loss dielectric material with plated through vias connecting the internal circuitry to the external printed circuit board, similar to that of the Xinger(R) hybrids and directional couplers. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 544-2414 +44 2392-232392 Available on Tape and Reel For Pick and Place Manufacturing. Model 0922B75-37AA Rev. A Mounting Configuration: 6X .030 [0.76] 75 Transmission Line In order for Xinger surface mount components to work optimally, there must be a 75 transmission line to the balanced port and 37.5 transmission lines from the unbalanced ports. If this condition is not satisfied, amplitude balance, insertion loss and VSWR may not meet published specifications. 6X .016 [0.41] Plated thru holes to ground .125 [3.17] All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability having X and Y thermal coefficient o of expansion (CTE) of 17 ppm/ C No copper area 2X 37.5 Transmission Line 4X .020 [0.51] An example of the PCB footprint used in the testing of these parts is shown to the left. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. Circuit Pattern Footprint Pad (s) Solder Resist Dimensions are in Inches [Millimeters] Mounting Footprint Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. Direction of Part Feed (Unloading) Dimensions are in inches [mm] Available on Tape and Reel For Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 544-2414 +44 2392-232392 Model 0922B75-37AA Rev. A OA OC OD QUANTITY/REEL 4000 USA/Canada: Toll Free: Europe: TABLE 1 REEL DIMENSIONS (inches [mm]) OA 13.0 [330.2] B 0.472 [12.0] OC 4.017 [102.03] OD 0.512 [13.0] (315) 432-8909 (800) 544-2414 +44 2392-232392 B Available on Tape and Reel For Pick and Place Manufacturing.