Charge Pump Regulator
for Color TFT Panels
ADM8839
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ©2006 Analog Devices, Inc. All rights reserved.
FEATURES
3 voltages (+5 V, +15 V, −15 V) from a single 3 V supply
Power efficiency optimized for use with TFT in mobile
phones
Low quiescent current
Low shutdown current (<5 μA)
Shutdown function
Option to use external LDO
APPLICATIONS
Hand-held instruments
TFT LCD panels
Cellular phones
FUNCTIONAL BLOCK DIAGRAM
OSCILLATOR
CONTROL
LOGIC
TIMING
GENERATOR
SHUTDOWN
CONTROL DISCHARGE
VOLTAGE
INVERTER
VOLTAGE
TRIPLER
LDO
VOLTAGE
REGULATOR
VOLTAGE
DOUBLER
C1+
C1–
LDO_IN
VOUT
+5VOUT
C2+
C2–
C3+
C3–
+15VOUT
C4+
C4–
–15VOUT –15V
+15V
+5V
GND
SHDN
LDO_ON/OFF
V
CC
DOUBLE
TRIPLE
C5, 2.2µF
C1, 2.2µF
C6, 2.2µF
C7, 2.2µF
C8, 0.22µF
C9, 0.22µF
C2, 0.22µF
C3, 0.22µF
C4, 0.22µF
ADM8839
+5VIN
03075-001
Figure 1.
GENERAL DESCRIPTION
The ADM8839 is a charge pump regulator used for color thin
film transistor (TFT) liquid crystal displays (LCDs). Using
charge pump technology, the device can be used to generate
three voltages (+5 V ± 2%, +15 V, −15 V) from a single 3 V
supply. These voltages are then used to provide supplies for the
LCD controller (5 V) and the gate drives for the transistors in
the panel (+15 V and −15 V). Only a few external capacitors are
needed for the charge pumps. An efficient low dropout (LDO)
voltage regulator ensures that the power efficiency is high, and
provides a low ripple 5 V output. This LDO can be shut down
and an external LDO can be used to regulate the 5 V doubler
output and drive the input to the charge pump section that
generates the +15 V and −15 V outputs, if required by the user.
The ADM8839 has a power save shutdown feature. The 5 V
output consumes the most power, so power efficiency is also
maximized on this output with an oscillator-enabling scheme
(Green Idle™). This effectively senses the load current that is
flowing and turns on the charge pump only when charge needs
to be delivered to the 5 V pump doubler output.
The ADM8839 is fabricated using CMOS technology for
minimal power consumption. The part is packaged in a 20-lead
LFCSP (lead frame chip scale package).
OBSOLETE
ADM8839
Rev. C | Page 2 of 12
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Timing Specifications .................................................................. 3
Absolute Maximum Ratings............................................................ 4
Thermal Characteristics .............................................................. 4
ESD Caution...................................................................................4
Pin Configuration and Function Descriptions..............................5
Typical Performance Characteristics ..............................................6
Theory of Operation .........................................................................8
Power Sequencing .........................................................................8
Transient Response .......................................................................8
Boosting the Current Drive of the ±15 V Supply .....................8
Outline Dimensions ....................................................................... 10
Ordering Guide .......................................................................... 10
REVISION HISTORY
7/06—Rev. B to Rev. C
Updated Format..................................................................Universal
Changes to Table 1............................................................................ 3
Changes to Table 5............................................................................ 5
Changes to Ordering Guide .......................................................... 10
Updated Outline Dimension......................................................... 10
7/05—Rev. A to Rev. B
Updated Ordering Guide .................................................................3
2/03—Rev. 0 to Rev. A
Changed Specifications.....................................................................2
Updated Outline Dimensions..........................................................8
OBSOLETE
ADM8839
Rev. C | Page 3 of 12
SPECIFICATIONS
VCC = 3 V (+40%/−10%); TA = −40°C to +85°C; C1, C5, C6, C7 = 2.2 μF; C2, C3, C4, C8, C9 = 0.22 μF; unless otherwise noted.
Table 1.
Parameter Test Conditions Min Typ Max Unit
INPUT VOLTAGE, VCC 2.7 4.2 V
SUPPLY CURRENT, ICC Unloaded 250 500 μA
Shutdown mode, TA = 25°C 5 μA
+5 V OUTPUT
Output Voltage IL = 10 μA to 20 mA 4.9 5.0 5.1 V
Output Current 5 20 mA
Output Ripple 8 mA load 10 mV p-p
Transient Response IL stepped from 10 μA to 8 mA 5 μs
+15 V OUTPUT
Output Voltage IL = 1 μA to 150 μA 14.0 15.0 16.0 V
Output Current 1 150 μA
Output Ripple IL = 100 μA 50 mV p-p
−15 V OUTPUT
Output Voltage IL = −1 μA to −150 μA −16.0 −15.0 −14.0 V
Output Current −150 −1 μA
Output Ripple IL = −100 μA 50 mV p-p
POWER EFFICIENCY R5 VOUT load = 5 mA, ±15 V load = ±150 μA, VCC = 3.0 V 82 %
CHARGE PUMP FREQUENCY 60 100 140 kHz
CONTROL PINS, SHDN
Input Voltage, V SHDN SHDN low = shutdown mode 0.3 × VCC V
SHDN high = normal mode 0.7 × VCC V
Digital Input Current ±1 μA
Digital Input Capacitance1 10 pF
LDO_ON/OFF
Input Voltage Low = External LDO 0.3 × VCC V
High = Internal LDO 0.7 × VCC V
Digital Input Current ±1 μA
Digital Input Capacitance1 10 pF
1 Guaranteed by design. Not 100% production tested.
TIMING SPECIFICATIONS
VCC = 3 V, TA = 25°C; C1, C5, C6, C7 = 2.2 μF; C2, C3, C4, C8, C9 = 0.22 μF.
Table 2.
Parameter Test Conditions/Comments Min Typ Max Unit
POWER-UP SEQUENCE
+5 V Rise Time, tR5V 10% to 90%, see Figure 14 250 μs
+15 V Rise Time, tR15V 10% to 90%, see Figure 14 3 ms
−15 V Fall Time, tFM15V 90% to 10%, see Figure 14 3 ms
Delay Between −15 V Fall and +15 V, tDELAY See Figure 14 600 μs
POWER-DOWN SEQUENCE
+5 V Fall Time, tF5V 90% to 10%, see Figure 14 35 ms
+15 V Fall Time, tF15V 90% to 10%, see Figure 14 10 ms
−15 V Rise Time, tRM15V 10% to 90%, see Figure 14 20 ms
OBSOLETE
ADM8839
Rev. C | Page 4 of 12
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 3.
Parameter Rating
Supply Voltage −0.3 V to +6.0 V
Input Voltage on Digital Inputs −0.3 V to +6.0 V
Output Short-Circuit Duration to GND 10 sec
Output Voltage
+5 V Output 0 V to 7.0 V
–15 V Output −17 V to +0.3 V
+15 V Output −0.3 V to +17 V
Operating Temperature Range −40°C to +85°C
Power Dissipation 50 mW
Storage Temperature Range −65°C to +150°C
ESD Class I
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL CHARACTERISTICS
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 4. Thermal Resistance
Package Type θJA Unit
20-Lead LFCSP_VQ 31°C °C/W
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
OBSOLETE
ADM8839
Rev. C | Page 5 of 12
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
V
CC
1
VOUT 2
LDO_IN 3
11 C3–
LDO_ON/OFF 6
SHDN 7
V
CC
8
GND 9
+15VOUT 10
+5VOUT 4
+5VIN 5
17 –15VOUT
16 C4+
PIN 1
INDICATOR
TOP VIEW
ADM8839
12 C3+
13 C2–
14 C2+
15 C4–
18 GND
19 C1–
20 C1+
0
3075-002
Figure 2. Pin Configuration
Table 5. Pin Function Descriptions
Pin No. Mnemonic Description
1 VCC Positive Supply Voltage Input. Connect this pin to the 3 V supply with a 2.2 μF decoupling capacitor. Must be
electrically tied together with Pin 8 by a PCB trace.
2 VOUT Voltage Doubler Output. This is derived by doubling the 3 V supply. A 2.2 μF capacitor to ground is required
on this pin.
3 LDO_IN Voltage Regulator Input. The user can bypass this circuit by using the LDO_ON/OFF pin.
4 +5VOUT 5 V Output. This is derived by doubling and regulating the 3 V supply. A 2.2 μF capacitor to ground is required
on this pin to stabilize the regulator.
5 +5VIN 5 V Input. This is the input to the voltage tripler and inverter charge pump circuits.
6 LDO_ON/OFF Control Logic Input. 3 V CMOS logic. A logic high selects the internal LDO for regulation of the 5 V voltage
doubler output. A logic low isolates the internal LDO from the rest of the charge pump circuits. This allows the
use of an external LDO to regulate the 5 V voltage doubler output. The output of this LDO is then fed back into
the voltage tripler and inverter circuits of the ADM8839.
7 SHDN Digital Input. 3 V CMOS logic. Active low shutdown control. This shuts down the timing generator and enables
the discharge circuit to dissipate the charge on the voltage outputs, thus driving them to 0 V.
8 VCC Connect this pin to VCC. Must be electrically tied with Pin 1 by a PCB trace.
9 GND Connect this pin to GND. Must be electrically tied with Pin 18 by a PCB trace.
10 +15VOUT 15 V Output. This is derived by tripling the 5 V regulated output. A 0.22 μF capacitor is required on this pin.
11, 12 C3−, C3+ External Capacitor C3 is connected between these pins. A 0.22 μF capacitor is recommended.
13, 14 C2−, C2+ External Capacitor C2 is connected between these pins. A 0.22 μF capacitor is recommended.
15, 16 C4−, C4+ External Capacitor C4 is connected between these pins. A 0.22 μF capacitor is recommended.
17 −15VOUT −15 V Output. This is derived by tripling and inverting the 5 V regulated output. A 0.22 μF capacitor is required
on this pin.
18 GND Device Ground. Must be electrically tied with Pin 9 by a PCB trace.
19, 20 C1−, C1+ External Capacitor C1 is connected between these pins. A 2.2 μF capacitor is recommended.
OBSOLETE
ADM8839
Rev. C | Page 6 of 12
TYPICAL PERFORMANCE CHARACTERISTICS
SUPPLY VOLTAGE (V)
LDO O/P VOL TAGE (V)
4.70
4.75
4.80
4.85
4.90
4.95
5.00
5.05
5.10
3.1 9.35.37.2 2.9 3.3 3.7 4.1 4.2
DEVICE AT –40°C
DEVICE AT +85°C
DEVICE AT +25°C
03075-003
Figure 3. LDO O/P Voltage Variation over Temperature and Supply
I
LOAD
(mA)
LDO O/P VOLTAGE (V)
4.995
5.000
5.005
5.010
5.015
5.020
20461357
8
03075-004
Figure 4. LDO O/P Voltage vs. Load Current
I
LOAD
(µA)
+15V/–15V POW ER EFFI CI ENCY (% )
30
40
50
60
70
80
90
100
30 001070501920 40 60 80 0
0
3075-005
Figure 5. +15 V/−15 V Power Efficiency vs. Load Current
LOAD CURRENT (mA)
LDO P OWE R E FFICIE NCY ( %)
75
76
77
78
79
80
81
84
82
387512 4 6
83
03075-006
Figure 6. LDO Power Efficiency vs. Load Current, VCC = 3 V
SUPPLY VOLTAGE (V)
SUPPLY CURRENT (µA)
150
200
250
300
350
400
3.1 9.35.37.2 2.9 3.3 3.7 4.1 4.2
03075-007
Figure 7. Supply Current vs. Supply Voltage
I
LOAD
(µA)
OUTPUT VOLTAGE (V)
14.1
14.2
14.3
14.4
14.5
14.6
14.7
14.8
14.9
15.0
15.1
500 100 150 200
–15V AT 25°C
+15V AT 25°C
0
3075-008
Figure 8. +15 V/−15 V Output Voltage vs. Load Current, Typical Configuration
OBSOLETE
ADM8839
Rev. C | Page 7 of 12
+15V OUTPUT
–15V OUTPUT
5VOUT
03075-009
Figure 9. +15 V and −15 V Outputs at Power-Up
V
OUT
RIPPLE (DOUBLER OUTP UT RIPP LE)
LDO OUTPUT RIPPLE
V
CC
RIPPLE
03075-010
Figure 10. Output Ripple on LDO (5 V Output)
LOAD DISABLE
5V OUTPUT
03075-011
Figure 11. 5 V Output Transient Response, Load Disconnected
LOAD ENABLE
5V OUTPUT
03075-012
Figure 12. Output Transient Response for Maximum Load Current
+15V O UTPUT
–15V O U T PUT
5VOUT
03075-013
Figure 13. +15 V and −15 V Outputs at Power-Down
OBSOLETE
ADM8839
Rev. C | Page 8 of 12
THEORY OF OPERATION
POWER SEQUENCING
For the TFT panel to power up correctly, the gate drive supplies
must be sequenced such that the −15 V supply is up before the
+15 V supply. The ADM8839 controls this sequence. When the
device is turned on (a logic high on SHDN), the ADM8839
allows the −15 V output to ramp immediately but holds off the
+15 V output. It continues to do this until the negative output
has reached −3 V. At this point, the positive output is enabled
and allowed to ramp to +15 V. This sequence is highlighted in
Figure 14.
V
CC
SHDN
+5V
+15V
–15V
t
RM15V
t
FM15V
t
DELAY
10%
10%
10%
90%
90%
90%
t
F15V
t
R15V
t
F5V
t
R5V
–3V
03075-014
Figure 14. Power Sequence
TRANSIENT RESPONSE
The ADM8839 features extremely fast transient response,
making it very suitable for fast image updates on TFT LCD
panels. This means that even under changing load conditions,
there is still very effective regulation of the 5 V output. Figure 11
and Figure 12 show how the 5 V output responds when a
maximum load is dynamically connected and disconnected.
Note that the output settles within 5 μs to less than 1% of the
output level.
BOOSTING THE CURRENT DRIVE OF THE ±15 V
SUPPLY
The ADM8839 ±15 V output can deliver 150 μA of current in
the typical configuration, as shown in Figure 15. It is also
possible to draw 100 μA from the +15 V output and 200 μA
from the −15 V output, or vice versa. It is possible to draw a
maximum of only 300 μA combined from the +15 V and the
−15 V outputs at any time (see Figure 16). In this configuration,
+5VOUT (Pin 4) is connected to +5VIN (Pin 5), as shown in
the functional block diagram (see Figure 1).
OSCILLATOR
CONTROL
LOGIC
TIMING
GENERATOR
SHUTDOWN
CONTROL DISCHARGE
VOLTAGE
INVERTER
VOLTAGE
TRIPLER
LDO
VOLTAGE
REGULATOR
VOLTAGE
DOUBLER
C1+
C1–
LDO_IN
VOUT
+5VOUT
C2+
C2–
C3+
C3–
+15VOUT
C4+
C4–
–15VOUT –15V
+15V
+5V
GND
SHDN
LDO_ON/OFF
V
CC
DOUBLE
TRIPLE
C5, 2.2µF
C1, 2.2µF
C6, 2.2µF
C7, 2.2µF
C8, 0.22µF
C9, 0.22µF
C2, 0.22µF
C3, 0.22µF
C4, 0.22µF
ADM8839
+5VIN
03075-015
Figure 15. Typical Configuration
I
LOAD
(µA)
OUTPUT VOLTAGE (V)
14.1
14.2
14.3
14.4
14.5
14.6
14.7
14.8
14.9
15.0
15.1
500 100 150 200
–15V AT 25°C
+15V AT 25°C
03075-016
Figure 16. +15 V/−15 V Output Voltage vs. Load Current,
Typical Configuration
OBSOLETE
ADM8839
Rev. C | Page 9 of 12
It is possible to configure the ADM8839 to supply up to 400 μA
on the ±15 V outputs by changing its configuration slightly, as
shown in Figure 17.
OSCILLATOR
CONTROL
LOGIC
TIMING
GENERATOR
SHUTDOWN
CONTROL DISCHARGE
VOLTAGE
TRIPLER
LDO
VOLTAGE
REGULATOR
VOLTAGE
DOUBLER CURRENT BOOST
CONFIGURATION
CONNECTION
C1+
C1–
LDO_IN
VOUT
+5VOUT
C2+
C2–
C3+
C3–
+15VOUT
C4+
C4–
–15VOUT –15V
+15V
+5V
GND
SHDN
V
CC
DOUBLE
TRIPLE
C5, 2.2µF
C1, 2.2µF
C7, 2.2µF
C8, 0.22µF
C9, 0.22µF
C2, 0.22µF
C3, 0.22µF
C4, 0.22µF
ADM8839
+5VIN
C6, 2.2µF
LDO_ON/OFF
03075-017
VOLTAGE
INVERTER
Figure 17. Current Boost Configuration
The configuration in Figure 17 can supply up to 400 μA of
current on both the +15 V and the −15 V outputs. If the load on
the ±15 V does not draw any current, the voltage on the ±15 V
outputs can rise up to ±16.5 V (see Figure 18). In this
configuration, VOUT (Pin 2) is connected to +5VIN (Pin 5).
14.0
14.5
15.0
15.5
16.0
16.5
17.0
0 100 200 300 400 500
I
LOAD
(µA)
OUTPUT VOLTAGE (V)
+15V AT 25°C
–15V AT 25°C
03075-018
Figure 18. +15 V/−15 V Output Voltage vs. Load Current,
Current Boost Configuration
OBSOLETE
ADM8839
Rev. C | Page 10 of 12
OUTLINE DIMENSIONS
1
20
5
6
11
16
15
10
2.25
2.10 SQ
1.95
0.75
0.55
0.35 0.30
0.23
0.18
0.50
BSC
12° MAX
0.20
REF
0.80 MAX
0.65 TYP 0.05 MAX
0.02 NOM
1.00
0.85
0.80
SEATING
PLANE
PIN 1
INDICATO
R
TOP
VIEW 3.75
BCS SQ
4.00
BSC SQ
COPLANARITY
0.08
0.60
MAX
0.60
MAX
0.25 MIN
COMPLIANT TO JEDEC STANDARDS MO-220-VGGD-1
PIN 1
INDICATOR
Figure 19. 20-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
4 mm × 4 mm Body, Very Thin Quad
(CP-20-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model Temperature Range Ordering Quantity Package Description Package Option
ADM8839ACP −40°C to +85°C 75 20-Lead LFCSP_VQ CP-20-1
ADM8839ACP-REEL −40°C to +85°C 5,000 20-Lead LFCSP_VQ CP-20-1
ADM8839ACP-REEL7 −40°C to +85°C 1,500 20-Lead LFCSP_VQ CP-20-1
ADM8839ACPZ1 −40°C to +85°C 75 20-Lead LFCSP_VQ CP-20-1
ADM8839ACPZ-REEL1 −40°C to +85°C 5,000 20-Lead LFCSP_VQ CP-20-1
ADM8839ACPZ-REEL71 −40°C to +85°C 1,500 20-Lead LFCSP_VQ CP-20-1
EVAL-ADM8839EB Evaluation Board
1 Z = Pb-free part.
OBSOLETE
ADM8839
Rev. C | Page 11 of 12
NOTES
OBSOLETE
ADM8839
Rev. C | Page 12 of 12
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C03075-0-7/06(C)
OBSOLETE
