Unmontierte Laserbarren, 82.5% Fullfaktor, 808 nm Un-mounted Laser Bars, 82.5% Fill-factor, 808 nm Lead (Pb) Free Product - RoHS Compliant SPL BS81-9S Besondere Merkmale Features * * * * * Unmontierter Laserbarren Design mit 75 Emittern (82.5% Fullfaktor) Empfohlene optische Spitzenleistung 150 W Typischer Konversionswirkungsgrad 52 % Hocheffiziente und zuverlassige MOVPE Quantenfilmstruktur * Standard-Wellenlangenselektion von 3 nm * Andere zentrale Pulswellenlangen auf Anfrage * Lotbare p- und n-seitige Metallisierung * * * * * Anwendungen Applications * Empfohlen fur quasi-kontinuierliche (QCW)Anwendungen * Pumpen von Festkorperlasern * Direkte Materialbearbeitung * Erwarmen, Beleuchten * Medizinische Anwendungen * Druckanwendungen * Recommended for quasi continuous wave (qcw)- applications * Pumping of solid state lasers * Direct material processing * Heating, illumination * Medical applications * Printing applications Sicherheitshinweise Safety Advices Je nach Betriebsart emittieren diese Bauteile hochkonzentrierte, nicht sichtbare InfrarotStrahlung, die gefahrlich fur das menschliche Auge sein kann. Produkte, die diese Bauteile enthalten, mussen gema den Sicherheitsrichtlinien der IEC-Norm 60825-1 behandelt werden. Depending on the mode of operation, these devices emit highly concentrated non-visible infrared light which can be hazardous to the human eye. Products which incorporate these devices have to follow the safety precautions found in IEC 60825-1 "Safety of laser products". 2009-12-21 Un-mounted monolithic linear array 75 emitter (82.5% fill-factor) design Recommended peak optical power 150 W Typical conversion efficiency 52 % High efficiency and reliable MOVPE-grown quantum-well structure * Standard wavelength selection is 3 nm * Other pulse peak wavelengths are available upon request * Solderable p- and n-side metallization 1 SPL BS81-9S Typ Type Spitzenleistung1) Peak Power1) SPL BS81-9S Wellenlange2) Wavelength2) 150 W Bestellnummer Ordering Code 804 nm Q65110A2676 1) Empfohlene Spitzenleistung setzt einen geringen thermischen Widerstand von Rth < 0.5 K/W voraus. Recommended peak optical power implies a low thermal resistanceof Rth < 0.5 K/W. 2) Mittlere Wellenlange bei 1 s Pulsbreite und 4 kHz Wiederholfrequenz eines unmontierten Barren. Andere Wellenlangen oder Toleranzen auf Anfrage erhaltlich. Pulsed peak wavelength at 1 s pulse width and at 4 kHz repetition rate refer to measurement on an un-mounted laser bar. Other peak wavelengths or tolerances are available upon request. Kennwerte (TA = 25 C)1) Characteristics1) Bezeichnung Parameter Symbol Symbol Wert Values Einheit Unit min. typ. max. Empfohlene Spitzenausgangsleistung Recommended peak output power Pop - 150 QCW - W Empfohlenes Tastverhatnis2) Recommended duty cycle2) d.c. - - 20 % PCOD 270 350 - W Schwellstrom Threshold current Ith - 17 21 A Betriebsstrom3) Operatiing current 3) Iop - 153 170 A 1.0 1.1 - W/A Gesamter Konversionswirkungsgrad3)4) Total conversion efficiency3)4) tot 48 52 - % Strahldivergenz schnelle Achse Vollwinkel (1/e)3) Beam divergence fast-axis full width (1/e)3) - 65 70 Grad deg. Strahldivergenz langsame Achse Vollwinkel (1/e) 3) Beam divergence slow-axis full width (1/e) 3) II - 9 12 Grad deg. pulse 801 804 807 nm Zerstorgrenze Catastrophic optical damage limit Differentielle Quanten-Effizienz3) Differential quantum efficiency3) Zentrale Impulswellenlange3) Standard pulse center wavelength3) 2009-12-21 2 SPL BS81-9S Kennwerte (TA = 25 C)1) Characteristics1) Bezeichnung Parameter Symbol Symbol Wert Values Einheit Unit min. typ. max. Spektrale Breite (Halbwertsbreite)3) Spectral width (FWHM)3) - 3 5 nm TE Polarisation 3)5) TE Polarization 3)5) PTE - 90 - % 1) Alle Kenn- und Grenzwerte beziehen sich auf Impulsmessungen (1 s Pulsbreite bei 4 kHz Wiederholfrequenz) an unmontierten Barren. Die Erzielung der spezifizierten Werte im QCW - Modus (Quasi Continuous Wave) setzt eine geeignete Montagetechnik mit einem thermischen Widerstand von Rth < 0.5 K/W voraus. Die zentrale Emissionswellenlange im Betrieb ist abhangig vom Betriebsmodus, Betriebstemperatur, thermischer Widerstand Rth und ist in aller Regel hoher als die spezifizierte Impulswellenlange pulse (1 s Pulsbreite bei 4 kHz Wiederholfrequenz). Alle Parameter konnen im jeweiligen Betriebsmodus von den spezifizierten Kennwerten abweichen. All characteristics and limitations refer to pulsed measurements on unmounted bars (1 s pulse width at 4 kHz repetition rate) implies a suitable mounting technology with a thermal resistance of Rth< 0.5 K/W. The operating peak emission wavelength depends on the operating mode, ambient temperature and thermal resistance Rth. The operating peak emission wavelength in general is higher than the specified pulsed peak wavelength pulse (1 s pulse width at 4 kHz repetition rate). All characteristics obtained in the operating mode may differ from the characteristics specified herein. 2) Das maximale Tastverhaltnis hangt von der Pulsbreite und dem thermischen Widerstand ab. The maximal duty cycle depends on pulse width and thermal impedance of the package. 3) Spezifiziert bei der typischen optischen Spitzenausgangsleistung Pop, typ Specified at the typical, peak optical output power Pop, typ 4) Der spezifizierte Wert fur den Konversionswirkungsgrad setzt eine homogene Strominjektion voraus The specified typical efficiency is reached under conditions of homogeneous current injection 5) Der spezifizierte Wert fur die Polarisation ist stark von der Montage abhangig The specified value for the polarisation strongly depends on bar mounting 2009-12-21 3 SPL BS81-9S Dimensionen Dimensions Bezeichnung Parameter Symbol Symbol Werte Values Einheit Unit min. typ. max. Emitteranzahl Number of emitters n - 75 - Kontaktbreite je Emitter Single emitter contact width w - 110 - m Emitterabstand Emitter pitch p - 130 - m Packungsdichte Fill-factor F - 82.5 - % Barrenbreite Bar width W 9.9 10 10.1 mm Barrenhohe Bar height H 105 115 125 m Resonatorlange Resonator length L 890 900 910 m Published by OSRAM Opto Semiconductors GmbH Leibnizstrasse 4, D-93055 Regensburg www.osram-os.com (c) All Rights Reserved. The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. Packing Please use the recycling operators known to you. We can also help you - get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components 1 , may only be used in life-support devices or systems 2 with the express written approval of OSRAM OS. 1 A critical component is a component usedin a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or effectiveness of that device or system. 2 Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health of the user may be endangered. 2009-12-21 4