782100 Series PE22100 Compatible Converter Transformers SELECTION GUIDE Order Code V Output Voltage V Isolation2 Voltage VDC Turns Ratio 3.3 5 3.3 5.0 3.3 3.3 5.0 5.0 4000 4000 4000 4000 1CT:1.33CT 1.14CT:1CT 1:2.14 1:1.33 Input Voltage 782100/33VC 782100/53VC 782100/35JVC 782100/55JVC Package Type DIL SM ORDER CODE DETAILS FEATURES pSemi PE22100 compatible 3.3V and 5V versions Isolation tested to 4kVDC Order Code 782100/XX(J)VC 782100/XXJVC-R Package Type 6 Pin (SM) / DIL 6 Pin SM Packaging Type Tube Tape & Reel Quantity 50 500 782100/33VC CHARACTERISTICS Parameter Conditions Min. Max. Units 100kHz, 20mV 100kHz, 250mV 100kHz, 250mV <0.1VDC Pins 1/2 or 2/3 190 310 8 11 600 H H pF UL 94 V-0 package materials Primary Inductance, LP1 Leakage Inductance, LL1 Inter winding Capacitance, CWW Primary D.C. Resistance, RDC1 Volt-time Product, Et Industrial temperature range 782100/53VC CHARACTERISTICS J-STD-020D reflow (SM versions) Parameter Conditions Min. Max. Units Primary Inductance, LP1 Leakage Inductance, LL1 Inter winding Capacitance, CWW Primary D.C. Resistance, RDC1 Volt-time Product, Et 100kHz, 20mV 100kHz, 250mV 100kHz, 250mV <0.1VDC Pins 1/2 or 2/3 150 260 8 8 600 H H pF Parameter Conditions Min. Max. Units Primary Inductance, LP1 Leakage Inductance, LL1 Inter winding Capacitance, CWW Primary D.C. Resistance, RDC1 Volt-time Product, Et 100kHz, 20mV 100kHz, 250mV 100kHz, 250mV >0.1VDC Pins 1/2 or 2/3 110 203 5 8 600 H H pF Parameter Conditions Min. Max. Units Primary Inductance, LP1 Leakage Inductance, LL1 Inter winding Capacitance, CWW Primary D.C. Resistance, RDC1 Volt-time Product, Et 100kHz, 20mV 100kHz, 250mV 100kHz, 250mV >0.1VDC Pins 1/2 or 2/3 170 335 8 8 600 H H pF Toroidal construction Low profile Industry-standard pinout RoHS compliant Backwards compatible with Sn/Pb soldering systems 13 m Vs 13 m Vs 782100/35JVC CHARACTERISTICS DESCRIPTION The 782100 series of converter transformers are specifically designed for use with the pSemi PE22100 chip set to provide isolated power supplies for transceivers in isolated interface applications. 18 m Vs 782100/55JVC CHARACTERISTICS 25 m Vs All specifications typical at TA=25C 1. LP, LL and RDC measured between pins 1-3. 2. Flash tested for 1 second For full details go to www.murata-ps.com/rohs www.murata-ps.com All enquiries: www.murata-ps.com/support KMP_782100_A03 Page 1 of 4 782100 Series PE22100 Compatible Converter Transformers ABSOLUTE MAXIMUM RATINGS Operating free air temperature range -40C to 85C Storage temperature range -50C to 125C VC VARIANTS SOLDERING INFORMATION Pin finish Peak wave solder temperature Matte tin 260C for 10 seconds JVC VARIANTS SOLDERING INFORMATION Pin finish Max. peak reflow temperature Moisture sensitivity level3 Max. time above liquidous (217C) Matte tin 245C 1 100s TECHNICAL NOTES ISOLATION VOLTAGE `Hi Pot Test', `Flash Tested', `Withstand Voltage', `Proof Voltage', `Dielectric Withstand Voltage' & `Isolation Test Voltage' are all terms that relate to the same thing, a test voltage, applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation. All products in this series are 100% production tested at their stated isolation voltage. A question commonly asked is, "What is the continuous voltage that can be applied across the part in normal operation?" For a part holding no specific agency approvals both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or 60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to safety standard requirements. REPEATED HIGH-VOLTAGE ISOLATION TESTING It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials, construction and environment. This series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage. This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further insulation system of physical spacing or barriers. 3. Representative samples of the product were subjected to the conditioning described in IPC/JEDEC J-STD-020D and passed electrical testing, package coplanarity and visual inspection which revealed no external cracks or changes in package body flatness. www.murata-ps.com All enquiries: www.murata-ps.com/support KMP_782100_A03 Page 2 of 4 782100 Series PE22100 Compatible Converter Transformers PACKAGE SPECIFICATIONS MECHANICAL DIMENSIONS DIL Package 9.77 (0.385) Max. SM Package Top View Primary Secondary 1 9.14 (0.360) Max. 12.70 (0.5) 9.52 (0.375) MAX 6 2 9.0 (0.354) MAX 5 782100/XXVC 3 XYYWW 4 Top View Primary Secondary 782100 1 6 XXJVC 2 5 XYYWW 3 4 6.35 (0.25) 6.35 (0.25) 3.440.50 (0.1350.02) 0.30(0.012) 0.20(0.008) 0.30 (0.012) 0.20 (0.008) 0.6 (0.024) 10.160.40 (0.400.016) 0.90 (0.035) 2.54 (0.1) 0.63 (0.025) 0.53 (0.021) 2.54 (0.1) Package weight: 1.1g Typ. Unless otherwise stated all dimensions in mm (inches) 0.25 (0.01). All pins on a 2.54 (0.1) pitch and within 0.25 (0.01) of true position. RECOMMENDED FOOTPRINT DETAILS VC Versions JVC Versions 0.10 (2.54) 0.06 (1.60) 0.10 (2.54) 0.10 (2.54) O0.05 (1.20) +0.006 (0.15) -0.000 (0.00) 0.04 (1.00) 0.45 (11.50) Unless otherwise stated all dimensions in mm (inches) 0.25 (0.01). All pins on a 2.54 (0.1) pitch and within 0.25 (0.01) of true position. TUBE OUTLINE DIMENSIONS 10.65 - 11.65 (0.419 - 0.459) 4.00 (0.16) 0.600.15 (0.0240.006) 12.95 (0.51) 5.20 (0.21) 3.80 (0.15) Tube material: Antistatic coated clear pvc Unless otherwise stated all dimensions in mm (inches) 0.25 (0.01). www.murata-ps.com 15.70 (0.62) Tube length: 5002 (19.70.08) Tube quantity: 50 All enquiries: www.murata-ps.com/support KMP_782100_A03 Page 3 of 4 782100 Series PE22100 Compatible Converter Transformers TAPE & REEL SPECIFICATIONS REEL OUTLINE DIMENSIONS 60 (2.36) Min. O382 (15.039) Max. 23.9-27.4 (0.94-1.08)* O 13.50 (0.53) 12.80 (0.50) Leader section 400 (15.7) Min. 100 (3.9) Min. 1.50 (0.059) Min. 30.4 (1.20) Max.g Goods enclosure section 24.4 (0.96)g 26.4 (1.04) Trailer section 160 (6.3) Min. Reel quantity: 500 Unless otherwise stated all dimensions in mm (inches) 0.25(0.01). O 20.20 (0.80) Min. * Includes flange distortion at outer edge. g Measured at hub. TAPE OUTLINE DIMENSIONS 4.00 (0.157) XYYWW 11.50 (0.453) 2.00 (0.079) 1.50 +0.10 +0.004 -0.00 (0.059 -0.000 ) 782100 XXJVC +0.30 +0.012 24.00 -0.10 (0.945 -0.004) 1.75 (0.069) Cover tape 7.20 (0.283) 9.37 (0.369) 12.00 (0.472) 0.60 (0.024) Max. Direction of unreeling Unless otherwise stated all dimensions in mm (inches) 0.25(0.01). This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. (c) 2018 Murata Power Solutions, Inc. www.murata-ps.com All enquiries: www.murata-ps.com/support KMP_782100_A03 Page 4 of 4