MINISMDC260F/12-02 - TE CONNECTIVITY

DTA143Z series

PNP -100mA -50V Digital Transistor (Bias Resistor Built-in Transistor) Datasheet

llOutline

Parameter Value SOT-723 SOT-416FL

VCC -50V

IC(MAX.) -100mA

R14.7kΩ DTA143ZM DTA143ZEB

R247kΩ (VMT3) (EMT3F)

SOT-416 SOT-323FL

llFeatures

1) Built-In Biasing Resistors, R1 = 4.7kΩ, R2 = 47kΩ

2) Built-in bias resistors enable the configuration of

　an inverter circuit without connecting external

　input resistors (see inner circuit) .

3) Only the on/off conditions need to be set

　for operation, making the circuit design easy.

4) Complementary NPN Types: DTC143Z series

DTA143ZE DTA143ZUB

(EMT3) (UMT3F)

SOT-323 SOT-346

llApplication

INVERTER, INTERFACE, DRIVER DTA143ZUA DTA143ZKA

(UMT3) (SMT3)

llInner circuit

DTA143ZM/ DTA143ZEB/ DTA143ZUB DTA143ZE/ DTA143ZUA/ DTA143ZKA

llPackaging specifications 　　　　　　　　　　　　　　　　　　　　　　

Part No. Package Package

size

Taping

code

Reel size

(mm)

Tape width

(mm)

Basic

ordering

unit.(pcs)

Marking

DTA143ZM SOT-723 1212 T2L 180 8 8000 E13

DTA143ZEB SOT-416FL 1616 TL 180 8 3000 E13

DTA143ZE SOT-416 1616 TL 180 8 3000 E13

DTA143ZUB SOT-323FL 2021 TL 180 8 3000 113

DTA143ZUA SOT-323 2021 T106 180 8 3000 113

DTA143ZKA SOT-346 2928 T146 180 8 3000 E13

www.rohm.com

DTA143Z series 　　　　　　　　　 Datasheet

llAbsolute maximum ratings (Ta = 25°C)

Parameter Symbol Values Unit

Supply voltage VCC -50 V

Input voltage VIN -30 to 5 V

Output current IO-100 mA

Collector current IC(MAX)*1 -100 mA

Power dissipation

DTA143ZM

PD*2

150

mW

DTA143ZEB 150

DTA143ZE 150

DTA143ZUB 200

DTA143ZUA 200

DTA143ZKA 200

Junction temperature Tj150 ℃

Range of storage temperature Tstg -55 to +150 ℃

llElectrical characteristics (Ta = 25°C)

Parameter Symbol Conditions

Values

Unit

Min. Typ. Max.

Input voltage

VI(off) VCC = -5V, IO = -100μA - - -0.5

V

VI(on) VO = -0.3V, IO = -5mA -1.3 - -

Output voltage VO(on) IO = -5mA, II = -0.25mA - -100 -300 mV

Input current II VI = -5V - - -1.8 mA

Output current IO(off) VCC = -50V, VI = 0V - - -500 nA

DC current gain GI VO = -5V, IO = -10mA 80 - - -

Input resistance R1- 3.29 4.7 6.11 kΩ

Resistance ratio R2/R1- 8 10 12 -

Transition frequency fT*1 VCE = -10V, IE = 5mA,

f = 100MHz - 250 - MHz

*1 Characteristics of built-in transistor

*2 Each terminal mounted on a reference land.

www.rohm.com

DTA143Z series 　　　　　　　　　　 Datasheet

llElectrical characteristic curves (Ta =25°C)

Fig.1 Input voltage vs. output current (ON

characteristics)

Fig.2 Output current vs. input voltage (OFF

characteristics)

Fig.3 Output current vs. output voltage Fig.4 DC current gain vs. output current

www.rohm.com

DTA143Z series 　　　　　　　　　　 Datasheet

llElectrical characteristic curves (Ta =25°C)

Fig.5 Output voltage vs. output current

www.rohm.com

DTA143Z series 　　　　　　　　　　　　　　 Datasheet

llDimensions

www.rohm.com

DTA143Z series 　　　　　　　　　 Datasheet

llDimensions

www.rohm.com

DTA143Z series 　　　　　　　　　 Datasheet

llDimensions

www.rohm.com

DTA143Z series 　　　　　　　　　 Datasheet

llDimensions

www.rohm.com

DTA143Z series 　　　　　　　　　 Datasheet

llDimensions

www.rohm.com

DTA143Z series 　　　　　　　　　 Datasheet

llDimensions

www.rohm.com

Datasheet

Notice-PGA-E Rev.001

Notice

Precaution on using ROHM Products

1. Our Products are designed and manufactured for applicatio n in ordinar y elec tronic eq uipm ents (such as AV equipment ,

OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you

intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport

equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car

accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or

serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.

Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any

damages, expenses or losses incurred b y you or third parties arisin g from the use of an y ROHM’s Prod ucts for Specific

Applications.

(Note1) Medical Equipment Classification of the Specific Applic ations

JAPAN USA EU CHINA

CLASSⅢ CLASSⅢ CLASSⅡb CLASSⅢ

CLASSⅣ CLASSⅢ

2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor

products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate

safety measures including but not limited to fail-safe d esign against the physical injur y, damage to any property, which

a failure or malfunction of our Products may cause. T he following are examples of safety measures:

[a] Installation of protection circuits or other protective devices to improve system safety

[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3. Our Products are designed and manufactured for use under standard conditions and not under any special or

extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way

responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any

special or extraordinary environments or conditions. If you intend to use our Products under any special or

extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of

product performance, reliabili ty, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents

[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlig ht or dust

[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,

H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves

[e] Use of our Products in proximity to heat-producing comp onents, plastic cords, or other flammable items

[f] Sealing or coating our Products with resin or other coating materials

[g] Use of our Products without cleaning residue of flu x (even if you use no-clean type fluxes, cleaning residue of

flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning

residue after soldering

[h] Use of the Products in places subject to dew condensation

4. The Products are not subject to radi ation-proof design.

5. Please verify and confirm ch aracteristics of the final or mounted products in using the Pro ducts.

6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,

confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power

exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect

product performance and reliability.

7. De-rate Power Dissipation (Pd) dependi ng on Ambient temp erature (T a). When used i n sealed area, co nfirm the actual

ambient temperature.

8. Confirm that operation temperature is within the specified range described in the product specification.

9. ROHM shall not be in any way responsible or lia ble for failure induced under deviant conditio n from what is defined in

this document.

Precaution for Mounting / Circuit board design

1. When a highly active halogen ous (chlori ne, bromine, etc.) flu x is used, the residue of flux may negativel y affect product

performance and reliability.

2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must

be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,

please consult with the ROHM represe ntative in advance.

For details, please refer to ROHM Mounting specification

Datasheet

Notice-PGA-E Rev.001

Precautions Regarding Application Examples and External Circuits

1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the

characteristics of the Products and external components, including transient characteristics, as well as static

characteristics.

2. You agree that application notes, reference designs, and associated data and information contained in this document

are presented only as guidance for Products use. Therefore, in case you use such information, you are solely

responsible for it and you must exercise you r own indepen dent verificatio n and judgmen t in the use of such information

contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses

incurred by you or third parties arising from the use of such information.

Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper

caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be

applied to Products. Please t ake special care under dry condit ion (e.g. Grounding of human body / equipment / sol der iron,

isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

Precaution for Storage / Transportati on

1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:

[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2

[b] the temperature or humidit y exceeds those recommended by ROHM

[c] the Products are exposed to direct sunshine or condensation

[d] the Products are exposed to hi gh Electrostatic

2. Even under ROHM recommended storage condition, solderabilit y of products out of recommended storage time period

may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is

exceeding the recommen de d storage time period.

3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads

may occur due to excessive s t ress applied when dropping of a carton.

4. Use Products wit hin the specified time after opening a humidity barrier bag. Baking is required before u s ing Products of

which storage time is exceeding the recommended storage time perio d.

Precaution for Product Label

QR code printed on ROHM Products label is for ROHM’s internal use only.

Precaution for Disposition

When disposing Products pl ease dispose them properly us ing an authorized industr y waste compan y.

Precaution for Foreign Exchange and Foreign Trade act

Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign

trade act, please consult with ROHM in case of export.

Precaution Regarding Intellectual Property Rights

1. All information and data including but not limited to application example contained in this document is for reference

only. ROHM does not warrant that foregoi ng information or data will not infringe any int ellectual property rights or any

other rights of any third party regarding such information or data.

2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the

Products with other articles such as components, circuits, systems or external equipment (including software).

3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any

third parties with respect to the Products or the information contained i n this document. Provide d, however, that ROHM

will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to

manufacture or sell products containing the Products, subject to the terms and conditions herein.

Other Precaution

1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.

2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written

consent of ROHM.

3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the

Products or this document for any military purposes, including b ut not limited to, the development of mass-destruction

weapons.

4. The proper names of companies or products described in this document are trademarks or registered trademarks of

ROHM, its affiliated companies or third parties.

DatasheetDatasheet

Notice – WE Rev.001

General Precaution

1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.

ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny

ROHM’s Products against warning, caution or note contained in this document.

2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior

notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s

representative.

3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all

information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or

liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccuracy or errors of or

concerning such information.

Datasheet

Part Number dta143zua

Package UMT3

Unit Quantity 3000

Minimum Package Quantity 3000

Packing Type Taping

Constitution Materials List inquiry

RoHS Yes

dta143zua - Web Page

Distribution Inventory

Buy