Data Sheet 26182.124C* 6810 DABiC-IV, 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER A6810xA OUT 8 1 18 OUT 9 OUT 7 2 17 OUT 10 OUT 6 3 16 SERIAL DATA OUT CLOCK 4 GROUND 5 LATCHES CLK REGISTER VBB 15 LOAD SUPPLY REGISTER 14 SERIAL DATA IN The A6810- devices combine 10-bit CMOS shift registers, accompanying data latches and control circuitry with bipolar sourcing outputs and pnp active pull downs. Designed primarily to drive vacuumfluorescent displays, the 60 V and -40 mA output ratings also allow these devices to be used in many other peripheral power driver applications. The A6810- feature an increased data input rate (compared with the older UCN/UCQ5810-F) and a controlled output slew rate. The CMOS shift register and latches allow direct interfacing with microprocessor-based systems. With a 3.3 V or 5 V logic supply, serial-data input rates of at least 10 MHz . A CMOS serial data output permits cascade connections in applications requiring additional drive lines. Similar devices are avail-able as the A6811- (12 bits), A6812- (20 bits), and A6818- (32 bits). The A6810- output source drivers are npn Darlingtons, capable of sourcing up to 40 mA. The controlled output slew rate reduces electromagnetic noise, which is an important consideration in systems that include telecommunications and/or microprocessors and to meet government emissions regulations. For inter-digit blanking, all output drivers can be disabled and all sink drivers turned on with a BLANKING input high. The pnp active pull-downs will sink at least 2.5 mA. The A6810- are available in two temperature ranges for optimum performance in commercial (suffix S-) or industrial (suffix E-) applications. They are provided in three package styles for through-hole DIP (suffix -A), surface-mount SOIC (suffix -LW), or minimum-area surface-mount PLCC (suffix -EP). Copper lead frames, low logicpower dissipation, and low output-saturation voltages allow all devices to source 25 mA from all outputs continuously over the maximum operating temperature range. T A C U IS D P Y O L E X N R 0 O P 1 D E 8 C 6 E N A E U R N HE E I T NT EF R O R C O F S I D -- LATCHES LOGIC SUPPLY 6 VDD STROBE 7 ST OUT 5 8 OUT 4 9 BLNK 13 BLANKING 12 OUT 1 11 OUT 2 10 OUT 3 Dwg. PP-029 ABSOLUTE MAXIMUM RATINGS at TA = 25C Logic Supply Voltage, VDD ................... 7.0 V Driver Supply Voltage, VBB ................... 60 V Continuous Output Current Range, IOUT ......................... -40 mA to +15 mA Input Voltage Range, VIN ....................... -0.3 V to VDD + 0.3 V Package Power Dissipation, PD ........................................ See Graph Operating Temperature Range, TA (Suffix `E-') .................. -40C to +85C (Suffix `S-') .................. -20C to +85C Storage Temperature Range, TS ............................... -55C to +125C Caution: These CMOS devices have input static protection (Class 2) but are still susceptible to damage if exposed to extremely high static electrical charges. FEATURES Controlled Output Slew Rate High-Speed Data Storage 60 V Minimum Output Breakdown Improved Replacements High Data Input Rate for TL4810-, UCN5810-, PNP Active Pull-Downs and UCQ5810- Low Output-Saturation Voltages Low-Power CMOS Logic and Latches Complete part number includes a suffix to identify operating temperature range (E- or S-) and package type (-A, -EP, or -LW). Always order by complete part number, e.g., A6810SLW . 6810 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER TYPICAL OUTPUT DRIVER V TYPICAL INPUT CIRCUIT VDD BB OUTN IN Dwg. EP-021-19 Dwg. EP-010-5 LATCHES GROUND CLK REGISTER REGISTER 5 VBB 17 16 LATCHES VDD STROBE 7 ST OUT 5 OUT 4 NO CONNECTION BLNK 15 BLANKING LOGIC SUPPLY 7 STROBE 8 8 13 OUT 2 9 12 OUT 3 NC 11 NO CONNECTION Dwg. PP-029-2 The products described here are manufactured under one or more U.S. patents or U.S. patents pending. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support devices or systems without express written approval. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. NC 15 SERIAL DATA IN 20 1 BLNK 14 ST LOAD SUPPLY 16 LATCHES OUT 1 NC V BB 17 REGISTER V DD 14 10 2 3 6 9 6 SERIAL DATA IN GROUND LATCHES REGISTER OUT 5 LOGIC SUPPLY LOAD SUPPLY 5 SERIAL DATA OUT BLANKING 13 4 SERIAL DATA OUT NC 18 CLK OUT1 CLOCK 18 4 12 OUT 6 3 OUT 10 CLOCK 11 19 2 OUT 9 10 20 The A6810xEP is a DISCONTINUED PRODUCT OUT 7 1 ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS OUT 8 19 OUT10 A6810xEP OUT 6 A6810xLW Dwg. PP-059 2.5 2.0 SUFFIX 'A', RJA = 65C/W 1.5 SUFFIX 'EP', RJA = 78C/W 1.0 0.5 SUFFIX 'LW', RJA = 90C/W 0 25 50 75 100 125 AMBIENT TEMPERATURE IN C 150 Dwg. GP-024-1A 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 Copyright (c) 1998, 2003 Allegro MicroSystems, Inc. 6810 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER FUNCTIONAL BLOCK DIAGRAM LOGIC SUPPLY V DD CLOCK SERIAL DATA IN SERIAL-PARALLEL SHIFT REGISTER STROBE LATCHES SERIAL DATA OUT BLANKING MOS BIPOLAR LOAD SUPPLY VBB GROUND OUT 1 OUT 2 OUT 3 OUT N Dwg. FP-013-1 TRUTH TABLE Serial Shift Register Contents Data Clock Input Input I1 I2 I3 ... IN-1 IN Serial Data Strobe Output Input Latch Contents I1 I2 I3 ... Output Contents IN-1 IN Blanklng I1 I2 I3 ... IN-1 IN H H R1 R2 ... RN-2 RN-1 RN-1 L L R1 R2 ... RN-2 RN-1 RN-1 X R1 R2 R3 ... RN-1 RN RN X X X L R1 R2 R3 ... RN-1 RN PN H P1 P2 P3 ... PN-1 PN L P1 P2 P3 ... PN-1 PN X X H L X X ... P1 P2 P3 ... L = Low Logic Level X PN-1 PN H = High Logic Level www.allegromicro.com X = Irrelevant X P = Present State X ... X R = Previous State L L ... L L 6810 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER ELECTRICAL CHARACTERISTICS at TA = +25C (A6810S-) or over operating temperature range (A6810E-), VBB = 60 V unless otherwise noted. Limits @ VDD = 3.3 V Characteristic Output Leakage Current Symbol ICEX Test Conditions VOUT = 0 V Limits @ VDD = 5 V Mln. Typ. Max. Min. Typ. Max. Units -- <-0.1 -15 -- <-0.1 -15 A 57.5 58.3 -- 57.5 58.3 -- V VOUT(1) IOUT = -25 mA VOUT(0) IOUT = 1 mA -- 1.0 1.5 -- 1.0 1.5 V Output Pull-Down Current IOUT(0) VOUT = 5 V to VBB 2.5 5.0 -- 2.5 5.0 -- mA Input Voltage VIN(1) 2.2 -- -- 3.3 -- -- V VIN(0) -- -- 1.1 -- -- 1.7 V Output Voltage Input Current Input Clamp Voltage Serial Data Output Voltage Maximum Clock Frequency Logic Supply Current IIN(1) VIN = VDD -- <0.01 1.0 -- <0.01 1.0 A IIN(0) VIN = 0 V -- <-0.01 -1.0 -- <-0.01 -1.0 A IIN = -200 A -- -0.8 -1.5 -- -0.8 -1.5 V VOUT(1) IOUT = -200 A 2.8 3.05 -- 4.5 4.75 -- V VOUT(0) IOUT = 200 A -- 0.15 0.3 -- 0.15 0.3 V 10* -- -- 10* -- -- MHz VIK fc IDD(1) All Outputs High -- 0.25 0.75 -- 0.3 1.0 mA IDD(0) All Outputs Low -- 0.25 0.75 -- 0.3 1.0 mA IBB(1) All Outputs High, No Load -- 1.5 3.0 -- 1.5 3.0 mA IBB(0) All Outputs Low -- 0.2 20 -- 0.2 20 A tdis(BQ) CL = 30 pF, 50% to 50% -- 0.7 2.0 -- 0.7 2.0 s ten(BQ) CL = 30 pF, 50% to 50% -- 1.8 3.0 -- 1.8 3.0 s tp(STH-QL) RL = 2.3 k, CL 30 pF -- 0.7 2.0 -- 0.7 2.0 s tp(STH-QH) RL = 2.3 k, CL 30 pF -- 1.8 3.0 -- 1.8 3.0 s Output Fall Time tf RL = 2.3 k, CL 30 pF 2.4 -- 12 2.4 -- 12 s Output Rise Time tr RL = 2.3 k, CL 30 pF 2.4 -- 12 2.4 -- 12 s Output Slew Rate dV/dt RL = 2.3 k, CL 30 pF 4.0 -- 20 4.0 -- 20 V/s IOUT = 200 A -- 50 -- -- 50 -- ns Load Supply Current Blanking-to-Output Delay Strobe-to-Output Delay Clock-to-Serial Data Out Delay tp(CH-SQX) Negative current is defined as coming out of (sourcing) the specified device terminal. Typical data is is for design information only and is at TA = +25C. *Operation at a clock frequency greater than the specified minimum value is possible but not warranteed. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 6810 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER TIMING REQUIREMENTS and SPECIFICATIONS (Logic Levels are VDD and Ground) C 50% CLOCK A SERIAL DATA IN B DATA 50% t p(CH-SQX) SERIAL DATA OUT DATA 50% D 50% STROBE BLANKING E LOW = ALL OUTPUTS ENABLED t p(STH-QH) t p(STH-QL) 90% DATA OUT N 10% Dwg. WP-029 HIGH = ALL OUTPUTS BLANKED (DISABLED) BLANKING 50% t dis(BQ) tr t en(BQ) OUT N 10% DATA tf 90% 50% Dwg. WP-030A A. Data Active Time Before Clock Pulse (Data Set-Up Time), tsu(D) ......................................... 25 ns B. Data Active Time After Clock Pulse (Data Hold Time), th(D) ............................................... 25 ns C. Clock Pulse Width, tw(CH) ............................................... 50 ns D. Time Between Clock Activation and Strobe, tsu(C) ....... 100 ns E. Strobe Pulse Width, tw(STH) ............................................. 50 ns NOTE - Timing is representative of a 10 MHz clock. Higher speeds may be attainable; operation at high temperatures will reduce the specified maximum clock frequency. Serial Data present at the input is transferred to the shift register on the logic "0" to logic "1" transition of the CLOCK input pulse. On succeeding CLOCK pulses, the registers shift data information towards the SERIAL DATA OUTPUT. The www.allegromicro.com SERIAL DATA must appear at the input prior to the rising edge of the CLOCK input waveform. Information present at any register is transferred to the respective latch when the STROBE is high (serial-to-parallel conversion). The latches will continue to accept new data as long as the STROBE is held high. Applications where the latches are bypassed (STROBE tied high) will require that the BLANKING input be high during serial data entry. When the BLANKING input is high, the output source drivers are disabled (OFF); the pnp active pull-down sink drivers are ON. The information stored in the latches is not affected by the BLANKING input. With the BLANKING input low, the outputs are controlled by the state of their respective latches. 6810 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER A6810EA & A6810SA Dimensions in Inches (controlling dimensions) 0.014 0.008 10 18 0.430 MAX 0.280 0.240 0.300 BSC 1 0.070 0.045 0.100 0.920 0.880 9 0.005 BSC MIN 0.210 MAX 0.015 0.150 0.115 MIN 0.022 0.014 Dwg. MA-001-18A in Dimensions in Millimeters (for reference only) 18 0.355 0.204 10 10.92 MAX 7.11 6.10 7.62 BSC 1 1.77 1.15 2.54 23.37 22.35 9 0.13 BSC MIN 5.33 MAX 0.39 3.81 2.93 MIN 0.558 0.356 NOTES: 1. 2. 3. 4. Dwg. MA-001-18A mm Exact body and lead configuration at vendor's option within limits shown. Lead spacing tolerance is non-cumulative. Lead thickness is measured at seating plane or below. Supplied in standard sticks/tubes of 21 devices. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 6810 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER A6810EEP & A6810SEP Dimensions in Inches (controlling dimensions) The A6810xEP is a DISCONTINUED PRODUCT 13 9 0.021 0.013 8 14 0.169 0.141 0.395 0.385 0.032 0.026 INDEX AREA 0.356 0.350 0.050 0.169 0.141 BSC 18 4 19 20 1 2 3 0.356 0.350 0.020 MIN 0.395 0.385 0.180 0.165 Dwg. MA-005-20A in Dimensions in Millimeters (for reference only) 13 9 0.533 0.331 10.03 9.78 0.812 0.661 INDEX AREA 9.042 8.890 1.27 4.29 3.58 8 14 4.29 3.58 BSC 18 4 19 0.51 MIN 4.57 4.20 20 1 2 3 9.042 8.890 10.03 9.78 Dwg. MA-005-20A mm NOTES: 1. Exact body and lead configuration at vendor's option within limits shown. 2. Lead spacing tolerance is non-cumulative. 3. Supplied in standard sticks/tubes of 48 devices or add "TR" to part number for tape and reel. www.allegromicro.com 6810 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVER A6810ELW and A6810SLW Dimensions in Inches (for reference only) 20 11 0.0125 0.0091 0.419 0.394 0.2992 0.2914 0.050 0.016 0.020 0.013 1 2 0.050 3 0.5118 0.4961 0 TO 8 BSC 0.0926 0.1043 0.0040 MIN. Dwg. MA-008-20 in Dimensions in Millimeters (controlling dimensions) 20 11 0.32 0.23 10.65 10.00 7.60 7.40 1.27 0.40 0.51 0.33 1 2 1.27 3 13.00 12.60 BSC 0 TO 8 2.65 2.35 0.10 MIN. Dwg. MA-008-20 mm NOTES: 1. Exact body and lead configuration at vendor's option within limits shown. 2. Lead spacing tolerance is non-cumulative. 3. Supplied in standard sticks/tubes of 37 devices or add "TR" to part number for tape and reel. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000