OSLON Black Series Lead (Pb) Free Product - RoHS Compliant LR H9GP, LA H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Besondere Merkmale Features * Gehausetyp: SMD Epoxyd Gehause mit Silikonlinse * Typischer Lichtstrom: 61 lm (rot); 80 lm (amber); 58 lm (gelb) bei 350 mA und bis zu 150 lm (rot); 180 lm (amber); 115 lm (gelb) bei 1 A * Besonderheit des Bauteils: Kompakte Lichtquelle fur platzsparende Designs; hohe Zuverlassigkeit * Wellenlange: 625 nm (rot), 617 nm (amber), 590 nm (gelb) * Abstrahlwinkel: 90 * Technologie: Dunnfilm InGaAlP * optischer Wirkungsgrad: 75 lm/W (rot), 89 lm/W (amber), 66 lm/W (gelb) bei 100 mA * Gruppierungsparameter: Lichtstrom, Wellenlange * Lotmethode: Reflow Loten * Vorbehandlung: nach JEDEC Level 2 * Gurtung: 8-mm Gurt mit 600/Rolle, o180 mm * ESD-Festigkeit: ESD-sicher bis 8 kV nach JESD22-A114-D * Erweiterte Korrosionsfestigkeit: Details siehe Seite 13 * * Anwendungen Applications * * * * * * * * * * * * * Die Produktqualifikation wurde entsprechend der Richtlinie AEC-Q101-REV-C, Stress Test Qualification for Automotive Grade Discrete Semiconductors", getestet. 2011-07-28 1 package: SMD epoxy package with silicon lens typical Luminous Flux: 61 lm (red); 80 lm (amber); 58 lm (yellow) at 350 mA and up 150 lm(red); 180 lm (amber); 115 lm (yellow) at 1 A feature of the device: small size high-flux LED for slim designs; high robustness wavelength: 625 nm (red), 617 nm (amber), 590 nm (yellow) viewing angle: 90 technology: Thinfilm InGaAlP optical efficiency: 75 lm/W (red), 89 lm/W (amber), 66 lm/W (yellow) at 100 mA grouping parameter: luminous flux, wavelength soldering methods: reflow soldering preconditioning: acc. to JEDEC Level 2 taping: 8 mm tape with 600/reel, o180 mm ESD-withstand voltage: up to 8 kV acc. to JESD22-A114-D Superior Corrosion Robustness: details see page 13 The product qualification test plan is based on the guidelines of AEC-Q101-REV-C, Stress Test Qualification for Automotive Grade Discrete Semiconductors. LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Bestellinformation Ordering Information Typ Type Emissionsfarbe Lichtstrom1) Seite 20 Color of Emission Luminous Flux1) page 20 Luminous Intensity2) page 20 IF = 350 mA V(lm) IF = 350 mA IV (cd) Lichtstarke Bestellnummer 2) Seite 20 Ordering Code LA H9GP-JYKY-24-1 amber 52.0 ... 97.0 36.5 (typ.) Q65111A0913 LR H9GP-HZKX-1-1 red 39.0 ... 82.0 29.6 (typ.) Q65111A1707 LY H9GP-HZKX-36-1 yellow 39.0 ... 82.0 29.6 (typ.) Q65111A1708 Anm.: Die oben genannten Typbezeichnungen umfassen die bestellbaren Selektionen. Diese bestehen aus wenigen Helligkeitsgruppen (siehe Seite 5 fur nahere Informationen). Es wird nur eine einzige Helligkeitsgruppe pro Gurt geliefert. Z.B.: LA H9GP-JYKY-24-1 bedeutet, dass auf dem Gurt nur eine der Helligkeitsgruppen JY, JZ, KX, oder KY enthalten ist. Um die Liefersicherheit zu gewahrleisten, konnen einzelne Helligkeitsgruppen nicht bestellt werden. Gleiches gilt fur die Farben, bei denen Wellenlangengruppen gemessen und gruppiert werden. Pro Gurt wird nur eine Wellenlangengruppe geliefert. Z.B.: LA H9GP-JYKY-24-1 bedeutet, dass auf dem Gurt nur eine der Wellenlangengruppen -2, -3, oder -4 enthalten ist (siehe Seite 5 fur nahere Information). Um die Liefersicherheit zu gewahrleisten, konnen einzelne Wellenlangengruppen nicht bestellt werden. Gleiches gilt fur die LEDs, bei denen die Durchlassspannungsgruppen gemessen und gruppiert werden. Pro Gurt wird nur eine Durchlassspannungsgruppe geliefert. Z.B.: LA H9GP-JYKY-24-1 bedeutet, dass nach Durchlassspannung gruppiert wird. Auf einem Gurt ist nur eine der Durchlasspannungsgruppen -9B oder -9C enthalten (siehe Seite 5 fur nahere Information). Um die Liefersicherheit zu gewahrleisten, konnen einzelne Durchlassspannungsgruppen nicht direkt bestellt werden. Note: The above Type Numbers represent the order groups which include only a few brightness groups (see page 5 for explanation). Only one group will be shipped on each reel (there will be no mixing of two groups on each reel). E.g.LA H9GP-JYKY-24-1 means that only one group JY, JZ, KX, or KY will be shippable for any one reel. In order to ensure availability, single brightness groups will not be orderable. In a similar manner for colors where wavelength groups are measured and binned, single wavelength groups will be shipped on any one reel. E.g. LA H9GP-JYKY-24-1 means that only 1 wavelength group -2, -3 or -4 will be shippable. In order to ensure availability, single wavelength groups will not be orderable (see page 5 for explanation). In a similar manner for LED, where forward voltage groups are measured and binned, single forward voltage groups will be shipped on any one reel. E.g. LA H9GP-JYKY-24-1 means that only 1 forward voltage group -9B or -9C will be shippable. In order to ensure availability, single forward voltage groups will not be orderable(see page 5 for explanation) 2011-07-28 2 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Grenzwerte Maximum Ratings Bezeichnung Parameter Symbol Symbol Wert Value Einheit Unit Betriebstemperatur Operating temperature range Top - 40 ... + 125 C Lagertemperatur Storage temperature range Tstg - 40 ... + 125 C Sperrschichttemperatur Junction temperature Tj 150 C Sperrschichttemperatur fur Kurzzeitanwendung* Junction temperature for short term applications* Tj 175* C (min.) IF (max.) IF 100 1000 mA mA mA Durchlassstrom Forward current (TS=25C) Stostrom Surge current t 50 ms, D = 0.016, TS=25C IFM 2500 Sperrspannung Reverse voltage (TS=25C) VR not designed for V reverse operation *Auch bei hochsten Temperaturen zeigt der LED Chip sehr gute Leistungsmerkmale. Die mittlere Lebensdauer bei Tj = 175C betragt 100h. *The LED chip exhibits excellent performance. Exemplary median lifetime for Tj = 175C is 100h. 2011-07-28 3 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Kennwerte Characteristics (TS = 25 C) Bezeichnung Parameter Symbol Symbol Werte Values red Wellenlange des emittierten Lichtes Wavelength at peak emission IF = 350 mA 624 597 nm dom 620 625 632 612 617* 624 583 590* 595 nm 18 18 18 nm 2 80 80 80 Grad deg. 2.05 2.15 2.65 2.05 2.2 2.65 2.05 2.25 2.65 V V V 6.5 11** K/W K/W (typ.) (min.) VF (typ.) VF (max.) VF Sperrstrom Reverse current Warmewiderstand Thermal resistance Sperrschicht/Lotpad Junction/solder point not designed for reverse operation (typ.) (max.) Rth JS Rth JS * Einzelgruppen siehe Seite 5 Individual groups on page 5 **Rth(max) basiert auf statistischen Werten Rth(max) is based on statistic values 2011-07-28 yellow 632 Abstrahlwinkel bei 50 % V (Vollwinkel) (typ.) Viewing angle at 50 % V Durchlassspannung 4) Seite 20) Forward voltage4) page 20 IF = 350 mA amber (typ.) peak Dominantwellenlange5) Seite 15 Dominant wavelength5) page 15 IF = 350 mA Spektrale Bandbreite bei 50 % Irel max Spectral bandwidth at 50 % Irel max IF = 350 mA Einheit Unit 4 6.5 11** 6.5 11** LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Durchlassspannungsgruppen6) Seite 20 Forward Voltage Groups6) page 20 Gruppe Group Durchlassspannung Forward voltage Einheit Unit min. max. 9B 2.05 2.35 V 9C 2.35 2.65 V Wellenlangengruppen (Dominantwellenlange)3) Seite 20 Wavelength Groups (Dominant Wavelength)3) page 20) Gruppe Group amber amber gelb yellow min. Einheit Unit min. max. 2 612 616 max. 3 616 620 583 586 4 620 624 586 589 nm 5 589 592 nm 6 592 595 nm nm nm Helligkeits-Gruppierungsschema Brightness Groups Helligkeitsgruppe Brightness Group HZ JX JY JZ KX KY Lichtstrom1) Seite 20 Luminous Flux1) page 20 V (lm) 39.0 ... 45.0 ... 52.0 ... 61.0 ... 71.0 ... 82.0 ... 45.0 52.0 61.0 71.0 82.0 97.0 Lichtstarke2) Seite 20 Luminous Intensity2) page 20 IV (cd) 20.6 (typ.) 23.8 (typ.) 27.7 (typ.) 32.3 (typ.) 37.5 (typ.) 43.8 (typ.) Anm.: Die Standardlieferform von Serientypen beinhaltet eine Familiengruppe. Diese besteht aus nur wenigen Helligkeitsgruppen. Einzelne Helligkeitsgruppen sind nicht bestellbar. Note: The standard shipping format for serial types includes a family group of only a few individual brightness groups. Individual brightness groups cannot be ordered. Gruppenbezeichnung auf Etikett Group Name on Label Beispiel: JY-2 Example: JY-2 Helligkeitsgruppe Brightness Group Wellenlange Wavelength JY 2 Anm.: In einer Verpackungseinheit / Gurt ist immer nur eine Helligkeitsgruppe enthalten. Note: No packing unit / tape ever contains more than one brightness group. 2011-07-28 5 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Relative spektrale Emission2) Seite 20 Relative Spectral Emission2) page 20 V() = spektrale Augenempfindlichkeit / Standard eye response curve rel = f (); TS = 25 C; IF = 350 mA OHL11701 100 % rel 80 V 60 yellow amber red 40 20 0 400 450 500 550 600 650 nm 700 Abstrahlcharakteristik2) Seite 20 Radiation Characteristic2) page 20 rel = f (); TS = 25 C 40 30 20 10 0 OHL04470 1.0 50 0.8 60 0.6 70 0.4 80 0.2 0 90 100 2011-07-28 1.0 0.8 0.6 0.4 0 6 20 40 60 80 100 120 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Durchlassstrom2) 4)Seite 20 Forward Current2) 4)page 20 IF = f (VF); TS = 25 C; red solid line: specified DC-range Durchlassstrom2) 4)Seite 20 Forward Current2) 4)page 20 IF = f (VF); TS = 25 C; amber solid line: specified DC-range OHL04412 1000 mA 1000 mA IF IF 800 800 700 700 600 600 500 500 400 400 300 300 200 200 100 100 0 1.6 1.8 2.0 2.2 2.4 0 1.6 1.8 2.0 2.2 2.4 2.6 2.6 V 2.8 Durchlassstrom2) 4)Seite 20 Forward Current2) 4)page 20 IF = f (VF); TS = 25 C; yellow solid line: specified DC-range 1000 mA OHL04413 IF 800 700 600 500 400 300 200 100 0 1.6 1.8 2.0 2.2 2.4 2.6 V 3.0 VF VF V 3.0 VF 2011-07-28 OHL04411 7 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Relativer Lichtstrom2) Seite 20 Relative Luminous Flux2) page 20 V/V(350 mA) = f (IF); TS = 25 C; red Relativer Lichtstrom2) Seite 20 Relative Luminous Flux2) page 20 V/V(350 mA) = f (IF); TS = 25 C; amber OHL04566 2.5 V V (350 mA) V V (350 mA) 2.0 2.0 1.5 1.5 1.0 1.0 0.5 0.5 0 200 400 600 0 mA 1000 2) Seite 20 Relativer Lichtstrom Relative Luminous Flux2) page 20 V/V(350 mA) = f (IF); TS = 25 C; yellow OHL04567 V V (350 mA) 2.0 1.5 1.0 0.5 0 200 400 600 mA 1000 IF 2011-07-28 200 400 600 mA 1000 IF IF 2.5 OHL04565 2.5 8 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Relative Spannung2) Seite 20 Relative Voltage2) page 20 VF = VF - VF(25 C) = f (Tj); IF = 350 mA; red, amber Relative Spannung2) Seite 20 Relative Voltage2) page 20 VF = VF - VF(25 C) = f (Tj); IF = 350 mA; yellow OHL04417 0.25 V OHL04418 0.20 V VF VF 0.15 0.10 0.10 0.05 0.05 0 0 -0.05 -0.05 -0.10 -0.10 -0.15 -40 -20 0 20 40 60 80 -0.15 -40 -20 0 C 120 Tj 2011-07-28 20 40 60 80 C 120 Tj 9 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Relativer Lichtstrom2) Seite 20 Relative Luminous Flux2) page 20 V/V(25 C)= f (Tj); IF = 350 mA; red Relativer Lichtstrom2) Seite 20 Relative Luminous Flux2) page 20 V/V(25 C)= f (Tj); IF = 350 mA; amber OHL14420 1.6 V V (25 C) V V (25 C) 1.2 1.2 1.0 1.0 0.8 0.8 0.6 0.6 0.4 0.4 0.2 0.2 0 -40 -20 0 20 40 60 80 0 -40 -20 0 C 120 Tj OHL14421 2.5 V V (25 C) 2.0 1.5 1.0 0.5 20 40 60 80 C 120 Tj 2011-07-28 20 40 60 80 C 120 Tj Relativer Lichtstrom2) Seite 20 Relative Luminous Flux2) page 20 V/V(25 C)= f (Tj); IF = 350 mA; yellow 0 -40 -20 0 OHL14419 1.6 10 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Dominante Wellenlange2) Seite 20 Dominant Wavelength2) page 20 dom = f (Tj); IF = 350 mA; red Dominante Wellenlange2) Seite 20 Dominant Wavelength2) page 20 dom = f (Tj); IF = 350 mA; amber OHL04423 8 nm dom dom 6 6 4 4 2 2 0 0 -2 -2 -4 -4 -6 -40 -20 0 20 40 60 80 -6 -40 -20 0 C 120 Tj OHL04424 15 nm dom 10 5 0 -5 20 40 60 80 C 120 Tj 2011-07-28 20 40 60 80 C 120 Tj Dominante Wellenlange2) Seite 20 Dominant Wavelength2) page 20 dom = f (Tj); IF = 350 mA; yellow -10 -40 -20 0 OHL04422 8 nm 11 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Maximal zulassiger Durchlassstrom Max. Permissible Forward Current IF = f (TS) IF OHL04484 1.1 A 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 Do not use current below 100 mA 0 0 20 40 60 80 100 C 140 TS Zulassige Impulsbelastbarkeit IF = f (tp) Permissible Pulse Handling Capability Duty cycle D = parameter, TS = 85 C Zulassige Impulsbelastbarkeit IF = f (tp) Permissible Pulse Handling Capability Duty cycle D = parameter, TS = 25 C 2.6 A IF 2.4 OHL04374 t D = TP 2.6 A IF 2.4 tP IF 1.8 1.6 1.4 1.2 t D = TP T IF T 2.2 2.2 2.0 OHL04374 tP 2.0 D= 0.005 0.01 0.02 0.05 0.1 0.2 0.5 1 1.8 1.6 1.4 1.2 D= 0.005 0.01 0.02 0.05 0.1 0.2 0.5 1 1.0 1.0 0.8 -5 10 10-4 10-3 10-2 10-1 100 101 s 102 0.8 -5 10 10-4 10-3 10-2 10-1 100 101 s 102 tp tp 2011-07-28 12 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Mazeichnung6) Seite 20 Package Outlines6) page 20 Anm.: Die LED enthalt ein ESD-Bauteil, das parallel zum Chip geschalten ist. Note: LED is protected by ESD device which is connected in parallel to LED-Chip. Korrosionsfestigkeit besser als EN 60068-2-60 (method 4): mit erweitertem Korrosionstest: 40C / 90%rh / 15pp m H2S / 336h Corrosion robustness better than EN 60068-2-60 (method 4): with enhanced corrosion test: 40C / 90%rh / 15ppm H2S / 336h Kathodenkennung: Cathode mark: Gewicht / Approx. weight: Markierung mark 25 mg Anm.: Das Gehause ist fur Ultraschallreinigung nicht geeignet Note: Package not suitalbe for ultra sonic cleaning 2011-07-28 13 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Gurtung / Polaritat und Lage5) Seite 20 Method of Taping / Polarity and Orientation5) page 20 2011-07-28 Verpackungseinheit 600/Rolle, o180 mm Packing unit 600/reel, o180 mm 14 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Empfohlenes Lotpaddesign5) Seite 20 Recommended Solder Pad5) page 20 Reflow Loten Reflow Soldering Anm.: Sollte das Leiterplattenlayout auch fur weitere OSLON Derivate oder zukunftige OSLON Derivate einsetzbar sein, muss die Warmesenke auf der Leiterplatte elektrisch gegen den Anoden- und Kathodenanschluss isoliert sein, um Varianten mit invertiertem Chip einsetzen zu konnen. Note: In case the PCB layout of the application is intended to be used with other OSLON derivates or in future developped OSLON derivates, the heat sink must not be electrically connected to anodeor cathode solder pad because of possible chip inverted polarity. 2011-07-28 15 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Lotbedingungen Soldering Conditions Vorbehandlung nach JEDEC Level 2 Preconditioning acc. to JEDEC Level 2 Reflow Lotprofil fur bleifreies Loten Reflow Soldering Profile for lead free soldering (nach J-STD-020D.01) (acc. to J-STD-020D.01) OHA04525 300 C T 250 Tp 245 C 240 C tP 217 C 200 tL 150 tS 100 50 25 C 0 0 50 100 150 200 250 s 300 t Profile Feature Pb-Free (SnAgCu) Assembly Recommendation Max. Ratings Ramp-up Rate to Preheat*) 25C to 150C 2C / sec 3C / sec Time ts from TSmin to TSmax (150C to 200C 100s min. 60sec max. 120sec Ramp-up Rate to Peak*) 180C to T P 2C / sec 3C / sec Liquidus Temperture TL 217C Time tL above TL 80sec max. 100sec Peak Temperature TP 245C max. 260C Time tP within 5C of the specified peak temperature TP - 5K 20sec min. 10sec max. 30sec Ramp-down Rate* TP to 100C 3K / sec 6K / sec maximum Time 25C to Peak temperature max. 8 min. All temperatures refer to the center of the package, measured on the top of the component * slope calculation T/t: t max. 5 sec; fulfillment for the whole T-range 2011-07-28 16 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Barcode-Produkt-Etikett (BPL) Barcode-Product-Label (BPL) OSRAM Opto BIN1: XX-XX-X-XXX-X LX XXXX Semiconductors RoHS Compliant (6P) BATCH NO: 1234567890 ML Temp ST 2 260 C R (1T) LOT NO: 1234567890 (9D) D/C: 1234 Pack: R18 DEMY 022 B_R999_1880.1642 R (X) PROD NO: 123456789(Q)QTY: 9999 (G) GROUP: XX-XX-X-X OHA04563 Gurtverpackung Tape and Reel W1 D0 P0 A N F W E 13.0 0.25 P2 Label P1 Direction of unreeling Direction of unreeling W2 Gurtvorlauf: 400 mm Leader: 400 mm Gurtende: Trailer: 160 mm 160 mm OHAY0324 Tape dimensions in mm (inch) W 8 + 0.3 - 0.1 P0 P1 P2 D0 E F 4 0.1 4 0.1 2 0.05 1.5 + 0.1 1.75 0.1 3.5 0.05 (0.157 0.004) (0.157 0.004) (0.079 0.002) (0.059 + 0.004) (0.069 0.004) (0.138 0.002) Reel dimensions in mm (inch) A 180 (7) 2011-07-28 W Nmin W1 W2 max 8 (0.315) 60 (2.362) 8.4 + 2 (0.331 + 0.079) 14.4 (0.567) 17 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Trockenverpackung und Materialien Dry Packing Process and Materials Moisture-sensitive label or print Barcode label L VE l LE see labe k, If code blan bar ). (RH . idity N s IVE RS Otain TO SIT UC TIcon SEN U < RH hum 0% e tive d C/6 kag rela are 30 _ < infr pac of 90% to ak ns ed (pe or rs e). ND Hou rs rs Hou and ject ditio cod C, 72 sing Hou e 5 bag E 48 C sub Hou con s UR ICO ces 24 6 dat 40 be time C ory ThiISTSEM pro < time . or 23 time at t will C) l with or fact ent MO . Flo time s TO at or at Flo l tica d tha or ival ure nth OP Flo 4 if: rea w Flo labe mo ices iden 5 ced equ el n e 5a is el ing, belo or 24 pro 6 Lev e dev : el cod e , unt whe Lev el re ow, see bag Lev l dat re mo bak bar ned Lev refl istu 10% re led time sea for istu ore> re ope e Mo see istu k, is or . sea is has k, Mo bef istu d 033 Mo in Flo RH blan Mo or-p blan in bag Car ing, r TDlife (if If with t. r lf 10%bak or J-S thisvapp. Yea _ eks rs < r ed icat med, C 1 Yea tem She ow, at uire not > y 1 WeHou unt DE Afte Ind 4 uire refl is red req 2. bod Mo /JE time 168 req : 2b a) Sto ices idity time or is IPC or time b) ned Flo or Hum ing ce time or Dev 2a e Flo a) ope or 3. b) bakren Flo 1 l dat Flo If 2 refe time el 2a 4. el sea 3 Lev el and Lev el re Bag e Lev re Lev istu Dat re istu re Mo istu Mo istu Mo Mo A rs C 1. AM R OS Humidity indicator Barcode label Please check the HIC immidiately after bag opening. Discard if circles overrun. Avoid metal contact. Do not eat. Comparator check dot WET If wet, examine units, if necessary bake units 15% If wet, examine units, if necessary bake units 10% 5% If wet, parts still adequately dry. change desiccant Humidity Indicator MIL-I-8835 AM Desiccant OSR OHA00539 Anm.: Feuchteempfindliche Produkte sind verpackt in einem Trockenbeutel zusammen mit einem Trockenmittel und einer Feuchteindikatorkarte Bezuglich Trockenverpackung finden Sie weitere Hinweise im Internet und in unserem Short Form Catalog im Kapitel "Gurtung und Verpackung" unter dem Punkt "Trockenverpackung". Hier sind Normenbezuge, unter anderem ein Auszug der JEDEC-Norm, enthalten. Note: Moisture-senisitve product is packed in a dry bag containing desiccant and a humidity card. Regarding dry pack you will find further information in the internet and in the Short Form Catalog in chapter "Tape and Reel" under the topic "Dry Pack". Here you will also find the normative references like JEDEC. Kartonverpackung und Materialien Transportation Packing and Materials 8 1 R1 Q- lti LS TO Y T6 PL 76 1+ PGR OU (G) Mu o pt rs O to uc (9D ) AM nd 21 00 21 99 8 : 4 co 44 Y: 20 (Q) SR NO mi O H H1 23 Se BA TC 3G : 12 (6P ) 5 NO T 14 2 LO ) (1T 11 00 : OD NO DE T6 PL 76 MY 1 R1 8 Q- lti LS TO Y 1+ P: PGR (G) 44 Mu 8 o : 01 99 pt rs O to ) 21 uc D/C 20 00 QT Y: (Q) M 00 (9D nd 21 : 4 SR ico A NO 23 m O H H1 Se TC 3G BA ) : 12 5 OS ) (1T NO OD (X) PR : 11 00 LO T 14 2 (6P OU Muster ED Bin Bin 1: Bin 2: P-1 3: Q-1 -20 ML -20 2 Te 2a 220 mp 3 240 ST Ad 260 C R C R0 diti R ona C RT PA 77 l TE CK VA XT R: (X) PR C NO D/C : 01 ). QT see labe 00 l k, N TIO U A P: Muster L VE LE code (RH blan If y bar . idit RH hum 60% e tive d C/ kag rela are 30 E S s _ < infr pac OR of tainITIV 90% to ak urs CT < e). or urs ted (pe ons con NS Ho g urs SE DU Ho and jec diti cod C, 72 sin Ho urs e 5 bag E ON 48 C sub e Ho con ces is UR 24 6 dat e MIC 40 be tim C h e ThISTSE pro < tory tim . or t wit 23 tim e at t will C) or fac MO . Flo al len tim s TO at or at Flo d or iva ure el nth s tha OP ntic Flo 4 if: rea Flo , lab ow mo ice equ ide 5 ced el e 5a is el ingen bel or 24 pro 6 Lev e dev, : el cod e , unt wh Lev el re ow see bag Lev l dat re mo bak e bar ned Lev refl istu 10% re led tim sea for istu ore> re ope se Mo see 3 istu is or . sea is Mo nk, bef istu pha nk, Flo , rd -03 Mo in RH bla Mo orbag bla hin ingCa TD life (if ar If wit t. vapp. 10%baktor J-S this elf Ye ar eks , _ < ed ica med, C 1 urs Ye erow tem Sh at uire not > y 1 WeHo unt DE Aft Ind 1. e 4 uire refl red req 2. bod Mo e ity is /JE tim 168 req : e 2b a) Sto es tim or mid is IPC or tim e vic b) ned Flo or Hu tim ing ce or De e 2a Flo a) ope or 3. b) bakren Flo dat e 1 l Flo If 2 el refe tim 2a 4. el sea 3 Lev g el and Lev el re Ba te Lev re Lev istu Da re istu re Mo istu Mo istu Mo Mo DE MY Barcode label ED Bin Bin 1: Bin 2: P-1 3: Q-1 -20 ML -20 2 Tem 2a 220 3 240 p ST Ad 260 C R C R0 diti R ona C RT PA 77 l TE CK VA XT R: Barcode label Packing Sealing label M RA OHA02044 Dimensions of transportation box in mm (inch) Breite / Width 200 5 (7,874 0,1968) 2011-07-28 Lange / length Hohe / height 200 5 (7,874 0,1968) 30 5 (1,1811 0,1968) 18 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Revision History: 2011-07-28 Previous Version: 2011-07-27 Page Subjects (major changes since last revision) Date of change all Preliminary Data Sheet created 2009-10-13 15 Note (Recommended Solder Pad) updated 2011-01-18 1 Applications updated 2011-02-24 2,5 Forward voltage groups introduced 2011-07-27 2 Q-Numbers updated 2011-07-27 1,14 Taping updated 2011-07-28 Patent List Patent No. US 6 066 861 US 6 277 301 US 6 245 259 Wegen der geplanten Streichung der LED aus der IEC 60825 erfolgt die Bewertung der Augensicherheit nach dem Standard IEC 62471:2006 ("photobiological safety of lamps and lamp systems") Im Risikogruppensystem dieser CIE- Norm erfullen die in diesem Datenblatt angegebenen LED die "exempt"- Gruppe (die die sich im "sichtbaren" Spektralbereich auf eine Expositionsdauer von 10000 s bezieht). Unter realen Umstanden (fur Expositionsdauer, Augenpupille, Betrachtungsabstand) geht damit von diesen Bauelementen keinerlei Augengefahrdung aus. Grundsatzlich sollte jedoch erwahnt werden, dass intensive Lichtquellen durch ihre Blendwirkung ein hohes sekundares Gefahrenpotenzial besitzen. Wie nach dem Blick in andere helle Lichtquellen (z.B. Autoscheinwerfer) auch, konnen temporar eingeschranktes Sehvermogen und Nachbilder je nach Situation zu Irritationen, Belastigungen, Beeintrachtigungen oder sogar Unfallen fuhren. Due to the planned cancellation of the LED from IEC 60825, the evaluation of eye safety occurs according to the standard IEC 62471:2006 ("photobiological safety of lamps and lamp systems"). Within the risk grouping system of this CIE standard, the LEDs specified in this data sheet fall into the "exempt" group (relating to devices in the visible spectrum with an exposure time of 10000 s). Under real circumstances (for exposure time, eye pupils, observation distance), it is assumed that no endangerment to the eye exists from these devices. As a matter of principle, however, it should be mentioned that intense light sources have a high secondary exposure potential due to their blinding effect. As is also true when viewing other bright light sources (e.g. headlights), temporary reduction in visual acuity and afterimages can occur, leading to irritation, annoyance, visual impairment, and even accidents, depending on the situation. Attention please! The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. If printed or downloaded, please find the latest version in the Internet. Packing Please use the recycling operators known to you. We can also help you - get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components7) page 20 may only be used in life-support devices or systems8) page 20 with the express written approval of OSRAM OS. 2011-07-28 19 LA H9GP, LR H9GP, LY H9GP Vorlaufige Daten / Preliminary Data Funoten: 1) Helligkeitswerte werden wahrend eines Strompulses einer typischen Dauer von 25 ms, mit einer internen Reproduzierbarkeit von +/- 8 % und einer erweiterten Messunsicherheit von +/- 11 % gemessen (gema GUM mit Erweiterungsfaktor k = 3). 2) Wegen der besonderen Prozessbedingungen bei der Herstellung von LED konnen typische oder abgeleitete technische Parameter nur aufgrund statistischer Werte wiedergegeben werden. Diese stimmen nicht notwendigerweise mit den Werten jedes einzelnen Produktes uberein, dessen Werte sich von typischen und abgeleiteten Werten oder typischen Kennlinien unterscheiden konnen. Falls erforderlich, z.B. aufgrund technischer Verbesserungen, werden diese typischen Werte ohne weitere Ankundigung geandert. 3) Die dominante Wellenlange wird wahrend eines Strompulses einer typischen Dauer von 25 ms, mit einer internen Reproduzierbarkeit von +/- 0,5 nm und einer erweiterten Messunsicherheit von +/- 1 nm gemessen (gema GUM mit Erweiterungsfaktor k = 3). 4) Vorwartsspannungen werden wahrend eines Strompulses einer typischen Dauer von 8 ms, mit einer internen Reproduzierbarkeit von +/- 0,05 V und einer erweiterten Messunsicherheit von +/- 0,1 V gemessen (gema GUM mit Erweiterungsfaktor k=3). 5) Im gestrichelten Bereich der Kennlinien muss mit erhohten Helligkeitsunterschieden zwischen Leuchtdioden innerhalb einer Verpackungseinheit gerechnet werden 6) Mae werden wie folgt angegeben: mm (inch) 7) Ein kritisches Bauteil ist ein Bauteil, das in lebenserhaltenden Apparaten oder Systemen eingesetzt wird und dessen Defekt voraussichtlich zu einer Fehlfunktion dieses lebenserhaltenden Apparates oder Systems fuhren wird oder die Sicherheit oder Effektivitat dieses Apparates oder Systems beeintrachtigt. 8) Lebenserhaltende Apparate oder Systeme sind fur (a) die Implantierung in den menschlichen Korper oder (b) fur die Lebenserhaltung bestimmt. Falls sie versagen, kann davon ausgegangen werden, dass die Gesundheit und das Leben des Patienten in Gefahr ist. Remarks: Brightness values are measured during a current pulse of typical 25 ms, with an internal reproducibility of +/- 8 % and an expanded uncertainty of +/- 11 % (acc. to GUM with a coverage factor of k = 3). 1) 2) 3) 4) 2011-07-28 5) In the range where the line of the graph is broken, you must expect higher brightness differences between single LEDs within one packing unit. 6) Dimensions are specified as follows: mm (inch). A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or the effectiveness of that device or system. 7) 8) Published by OSRAM Opto Semiconductors GmbH Leibnizstrasse 4, D-93055 Regensburg www.osram-os.com (c) All Rights Reserved. 20 Due to the special conditions of the manufacturing processes of LED, the typical data or calculated correlations of technical parameters can only reflect statistical figures. These do not necessarily correspond to the actual parameters of each single product, which could differ from the typical data and calculated correlations or the typical characteristic line. If requested, e.g. because of technical improvements, these typ. data will be changed without any further notice. The dominant wavelength is measured at a current pulse of typical 25 ms, with an internal reproducibility of +/- 0,5 nm and an expanded uncertainty of +/- 1 nm (acc. to GUM with a coverage factor of k=3). The forward voltage is measured during a current pulse of typical 8 ms, with an internal reproducibility of +/- 0,05 V and an expanded uncertainty of +/- 0,1 V (acc. to GUM with a coverage factor of k=3). Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health and the life of the user may be endangered.